Search Documents

By K. V. Raj

"Air inversion is a meteorological phenomenon generally occurs during winter times. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for health and safety of miners. Mine operations cease if the concentration of NOx or CO exceeds the threshold limit value (TLV) of the pollutants. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Studies of the turbulence parameters suggest that effective ventilation of the pit and removal of pollutants can be accomplished if a large enough mixing length in the open pit can be created. Turbulent mixing by eddies of different length scales under an inversion layer is product of wind shear, thermal gradient and buoyancy. The main result of turbulence is mixing of the atmospheric profile and transport of momentum. Computational fluid dynamics (CFD) Simulation results of a novel mitigation approach using cloud cover will be presented in this paper. INTRODUCTION In extreme climatic conditions, deep open-pit mines tend to trap pollutants at the pit bottom due to air inversions. Keeping open pits adequately ventilated is a considerable challenge for the mining community. Mine operators in cold regions are very familiar with this problem, the severity of which can be judged from Figures 1 and 2. The top portion of the figures show clear sky and snow covered benches. The brown haze, containing various contaminants accumulated over time in the pit under the air inversion, can be seen in the bottom portion of the figures. Several Arctic or subarctic mines have reported air inversions. Even Rio Tinto’s Bingham Canyon pit in Utah has reported local air inversions from time to time [1].Mitigation of pollutants in deep open-pit mines in the Arctic is a challenging task. Release of pollutants below the inversion height in an open-pit mine during periods of weak winds and consequently weak vertical mixing may result in very high concentrations of primary and secondary pollutants, causing serious consequences for human health. Mine operations cease if the concentration of any one of the pollutants (NOx or CO) exceeds the TLV. Sustained cessation of a mine operation has serious economic consequences. For continued mining operation, the levels of pollutants must be below the TLVs. If no significant synoptic meteorological situation changes during an inversion, a warm air mass sits over the cold air mass within the open pit. Artificial ventilation is required to dilute the pollutants to an extent that mine workers can safely resume work. Some of the early approaches in artificially ventilating open pits were attempted in the USSR. Most of the studies by Soviet researchers suggested the use of turbojets and turbo-propeller engines, airscrews, axial pit fans, and meteotrons [2, 3]. However, the majority of these studies were only theoretical in nature, with no evidence of an approach that really worked in practice."

Jan 1, 2017

By Davood Moradkhani, Maryam Rasouli

"The present study reports solvent extraction and separation of zinc from concentrated nickel sulfate solution. In our previous study, Zn and Cd in cold filter cake (CFC, 45-55% Zn, 11-16% Cd, and 2.5-4% Ni) were extracted by alkaline leaching followed by electrowinning processes respectively. The strip solution from electrowinning process, was a pregnant liquor solution (PLS) containing 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process for separation of traces of Zn from high grade nickel. The zinc free raffinate containing 16.6 g/l Ni sulfate solution will flow to nickel electrowinning plant for cathode production. Di-(2-ethylhexyl) phosphoric acid (D2EHPA) is the organic phase used in this study. The effects of various parameters such as organic phase concentration (10- 40 % v/v), pH (1.5-3), and temperature (25 and 45°) are investigated. Zinc over nickel separation factor increases by increasing pH from1.5 to 3. The results show that 98.7% of Zn was loaded at25°C O/A ratio of 1, pH 3, and 10% vol. D2EHPA. A 10 M NaOH is used for pH control. However, replacement of pH controlling agent with ammonia solution (25%. v/v) results in interesting observations. Ammonia addition, reduces the solubility of Ni2+ cations in solution. Nickel starts to precipitate from raffinate in a crystalline bluish-green form. The obtained crystals are characterized by XRF and identified to be nickel-bearing analog of boussingaultite, a rare sulfate mineral of nickel with chemical formula of Ni (NH4)2(SO4)2.6H2O. The crystallization rate of crystals is studied. It is a slow precipitation process with 75% in 4 days.INTRODUCTION Annually, many hydrometallurgical processes such as electrowinning, solvent extraction and leaching are applied to waste filter cakes in Zanjan, Iran. These additional processes on filter cakes are critical from both environmental and economic points of view. CFC (cold filter cake) is a toxic but valuable filter cake (45-55% Zn, 11-16% Cd, 2.5-4% Ni, and 0.2-1.5% Cu) produced in many zinc production plants. Our research group at Research and Engineering Company for Non-ferrous Metals (ReCo.), developed a series of hydrometallurgical methods for extraction of zinc, cadmium and nickel from CFC (Moradkhani, & Rasouli 2012). The recovery of zinc and cadmium with alkaline leaching and electrowinning was successfully studied. The strip sulfate solution from cadmium electrowinning unit, contains high concentration of nickel with some traces of zinc impurity. This pregnant liquor solution (PLS) was analyzed and reported to contain 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process to separate Zn from nickel (Fig. 1). The organic phase stripping solution containing 4.2 g/l zinc and 200 ppm nickel can be circulated and used in the acidic leaching step. This generates nickel solution with high purity suitable for nickel cathode production."

Jan 1, 2017

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By S. D. Graham

"The extractive metallurgy of gold is largely controlled by mineralogical factors such as the presence of refractory gold, particle size, gangue mineral associations, presence of preg-robbers, oxygen and cyanide consumers, and locking characteristics in base metal sulphides. Light microscopy and automated mineralogy techniques are regularly used to characterise the effect of these variables on gold recovery. However, despite their widespread application there are a range of limitations when grades are low. Typically, the analysis of low-grade samples requires the preparation and analysis of numerous polished blocks. This is often costly and time consuming, with complexities regarding analysing statistically representative particle quantities and problems overcoming stereological bias. This is compounded by the “nugget” effect and high tenor nature of gold mineralisation. X-ray Microscopy techniques have the potential to overcome many of these problems, in particular the statistical representivity of analysis, removing stereological bias and effectively locating phases that are present in ultra-trace proportions. In this paper we outline the potential benefits of employing X-ray Microscopy (XRM) in characterising gold losses from a typical Cu-Au porphyry project, which were illusive in 2D based analysis. The talk will also outline additional application areas of XRM within the extractive value chain."

Jan 1, 2017

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By Qi Wang, Zengzhu Kang, Jianguo Liu, Guanglei Liu

"Due to the increase of automotive vehicles, available parking spaces become a new type of limited resource in central cities of China, especially in those old districts without visionary urban planning. Additional mechanical parking in underground space is an efficient solution to provide parking spaces under the situation where the urban space is constrained. Shichahai district is an old protected zone in Beijing which is close to the Forbidden City and there are many Hutong (alleyway) and Quadrangles (courtyard house). No spaces are available for car parking on the ground and all vehicles are parking in Hutong without order currently. The local government plan to do renovation work for this district and improve the residential environment. Several innovative solutions are studied including parking in deep shafts, parking under existing buildings by under-pinned method, parking under buildings by covered excavation method, parking under roads built together with utility tunnel etc. 5000 difference types underground parking spaces are planned to be constructed in the following three years. Project examples are also introduced in this paper. INTRODUCTIONCar parking resources are very limited in central cities, especially in old districts without planning for increasing automotive vehicle volume. Traffic get worse when cars park on the side of the roads or move slowly to find parking spaces. Investigation shows the normal (parking space/ automotive vehicle volume) ratio is about 1.2 in most big cities such as New York, Tokyo and Hong Kong, while this ratio is only 0.5 in Beijing. One solution is to move cars out of central cities. But there are still huge parking requirements for the citizens living in central cities. Shichahai district is an historic protected zone in Beijing which is close to the Forbidden City and there are many Hutong and Quadrangles (refer to Figure 1 for project location). No spaces are available for car parking on ground and all vehicles are parked in Hutong without order currently. The local government had a plan to do renovation work of this district and improve the residence environment. 5000 different types of underground parking spaces are planned to be constructed in the following three years. One project designed and to be constructed by Zhongyan Technology will be introduced in this paper. Other innovative solutions will be introduced briefly as well."

Jan 1, 2017

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By J. Herbst, J. Groppo, A. Noble, R. Q. Honaker

"Coal and coal byproducts produced annually contain enough rare earth elements (REEs) to meet current U.S. demand. The REEs exist in the form of minerals, ion-exchanged elements associated with clays and chemically bonded elements within the organic coal matrix. Researchers at three universities have collaborated to evaluate the effectiveness of existing physical and chemical concentration processes for the recovery of the REEs. The efforts have found that physical separation processes can increase the total REE content in the thickener underflow material collected from a Central Appalachian coal cleaning facility from around 300 ppm to values greater than 17,500 ppm on an ash basis. On the other hand, leaching was effective in recovering REEs from coarse middlings materials collected from multiple coal basins as indicated by recovery values exceeding 80%. Based on material characterization data and process evaluations conducted for several potential feed coal sources, economic recovery of the REEs will require byproduct production of both clean coal and REE concentrate using a process flowsheet that is unique for each source. INTRODUCTION Recent studies initiated by NETL showed that U.S. coals contain significant amounts of rare earth elements (REEs), suggesting that rare earth minerals (REMs) and/or REEs can be produced as byproducts [1]. According to the report, the richest source of REEs is the Central Appalachian coal. At present, there are 208 coal preparation plants located in the region (WV, KY, PA, VA, AL, TN) with a capacity of 166,495 tons/hr or more than 1 billion tons annually [2]. If only a portion of these plants are retrofitted with advanced separation processes, the U.S. coal industry can become a significant producer of RE minerals as byproducts. An inherent advantage of becoming a byproduct producer of REEs is that no mining cost needs to be part of the product cost. Other researchers have also shown that coal can be a significant source of REEs. The average sum of the rare earth plus yttrium (REY) concentration of the world coal is approximately 68.5 ppm, which is lower than the corresponding upper crustal concentration (UCC) (168.4 ppm). However, the average REY content of the mineral matter in the world (404 ppm) and U.S. coals (517 ppm) are 3 times higher than the average UCC. Some of the mineral matter in Russian and Chinese coals have REY concentrations in the range of 0.68 to 2.03% and contain a better source of higher value REYs than many primary rare earth deposits [3]."

Jan 1, 2017

By M. Savella

The Runruno Gold Project is located on the island of Luzon, approximately 200 km north of Manilla in the Philippines. The mine is a surface mine operation and use the proven BIOX® and carbon in leach processes to recover gold, and the ASTER™ process for detoxification of the CIL residue prior to discharge to the Residue Storage Impoundment (RSI). Work to date has defined a mineral resource of 1.39 million ounces of gold, and the operation will produce 96,700 ounces of gold per annum over a mine life of 10.4 years. The BIOX® circuit is designed to treat 140,000 tpa of concentrate with a design capacity of 404 tpd of concentrate at a design sulphide sulphur grade of 17% S2-. The Runruno project is the first BIOX® plant to implement the Generation III BIOX® design principles. As part of the Generation III BIOX® program Outotec supplied a turnkey, containerised metallurgical laboratory to facilitate the first four stages of the BIOX® and ASTER™ inoculum build up requirements. BIOX® inoculum build-up was started during early January 2015 with 5 litres of stock cultures shipped from South Africa. The BIOX® culture was successfully adapted to concentrate produced from the mini plant during March 2015. The ASTER™ inoculum build-up commenced during early August 2015 utilising 27 litres of ASTER™ bacterial inoculum already adapted to similar process conditions expected during commercial operation. This paper will detail the various stages of inoculum build-up through to commissioning and ramp-up of the BIOX® and ASTER™ Processes at the Runruno Gold Project. The paper will highlight some of the factors affecting the commissioning process as well as the improvements seen through the introduction of the Generation III BIOX® design principles.

Jan 1, 2017

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

The Curtin University Gold Technology Group has been involved in surveying, modelling and optimisation of batch centrifugal concentrator type gravity circuits and CIP/CIL circuits for nearly two decades. The most commonly asked question regarding gravity recovery is, “What is the benefit of a gravity circuit”, which can be hard, if not impossible, to quantify. With the help of the AMIRA P420 Project’s Integrated Liberation Leach Model (ILLM) it is now possible to evaluate the effect of gravity recovery on total gold recovery when changes are made to the grind size, gravity and/or leach/adsorption circuits. This paper demonstrates how the ILLM can be used to determine the net benefit of introducing or modifying a gravity circuit and assess the effect of operating conditions (grind size, coarse gold size distribution, leach residence time, carbon activity, etc.) on plant performance.

Jan 1, 2017

By Quenton Johnson, W. A. Gough, David Carr

"This paper describes the application of the BrainWave Model Predictive Controller (MPC) and Advanced Control Expert (ACE) Advanced Supervisory Control System on the SAG Mill, Ball Mill, and Rougher Flotation cells for a new gold processing line at the Oceana Gold - Haile Gold mine in Kershaw, South Carolina. For this project, ANDRITZ supplied the control system design and programming, operator-training simulator and advanced control. The advanced control was tested against the IDEAS™ dynamic simulator, and commissioned during the startup of the processing plant to help achieve target production as quickly as possible. Operators were able to run the equipment in a consistent and optimized manner from an early stage of the plant operation, increasing efficiency and profitability. MPC is able to reduce process variability beyond the best performance that can be obtained with conventional Proportional Integral Derivative (PID) control methods. MPC is able to optimize the control of processes that exhibit an integrating type response in combination with transport delays or variable interaction, which are characteristic of many gold processes including SAG mill weight control and Flotation cell froth level control. The experience and benefits of applying MPC during the startup of a new gold processing plant are presented in this paper.INTRODUCTION Mineral processing operations present many challenges for automatic process control due to variations in unmeasured ore properties, material transport delays, and non-linear response characteristics. Advanced process control technologies such as expert systems and multi-variable model predictive controllers are often used to improve the control of these processes to increase productivity and recovery efficiency. Typically these systems are applied after the mine has been in operation for a period of time. For this project, a complete dynamic process simulator was developed using the IDEAS platform for the purpose of training operators before the plant was constructed. Operators were able to become familiar with the process and the control system in order to become proficient in the use of the controls before the plant was ready to start. They were able to practice abnormal condition management including startup and shutdown of the process using the simulator and develop complete Standard Operating Procedures (SOPs) for these situations. The simulator was also used to test the control system functionality and operator Human Machine Interface (HMI) configuration to reduce errors and improve the performance of the control system during plant start-up."

Jan 1, 2017

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By Roberto Pena, Cristhian Morales, Darwin Morales, Veronica Cambiaso

"This article makes evident the shortcomings of the current operation of oxygen pipes as well as the damages they cause and why they cause them. When focusing on the causes and effects of these drawbacks, it was possible to develop a new family of thermal lances that could pierce a taphole with the precision of a drill but with the capacity to complete the whole operation. Although efforts have been made to replace oxygen pipes since they are annoying, dangerous and inefficient, nobody had worked to improve the way the traditional oxygen pipe taps/perforates the furnaces and reactors tapholes. In fact, developments made in drills and robotic arms, have failed to replace the oxygen pipe, which despite their negative side effects have been used for more than a century. Observation and theory were key to radically transform this humble tool into a dependable and efficient support in the operation. A good news that it is worthwhile to share for the benefit of all of us, passionate about the world of pyro metallurgy.INTRODUCTION Normally, reports and papers prepared for conventions, symposia or other technical events related to metallurgy aim to relevant topics in the operational field, probably because in them lay the scale economies every company pursues. We intend to give relevance to a matter normally disregarded in operations, but that unmistakably vital: if the furnace or reactor cannot be bled, the pyrometallurgical process will not be completed. Besides, if the tapping task is difficult or is long delayed, the availability of the furnace will be reduced. Consequently, there will be a waste of energy and workers will be exposed to dangerous levels of radiation as well as to work overload and physical injuries Apart from these basic effects, in tapping operations where oxygen pipes are used, we can see serious damages in the smelting furnace, especially in the taphole components such as refractory bricks, taphole jackets and water cooled plates. This paper intends to show that taking care of the tapping task can significantly upgrade not only to the tapping operation itself, but also the whole plant productivity."

Jan 1, 2017