Search Documents

By Francisco Tamargo

"This paper refers to a new process for the full recovery (above 98%) of zinc and other valuable metals (Pb, Ag, Au) accompanying zinc in its concentrates while iron is separated as a marketable product free of any harmful impurities and suitable for sale to the cement industry. The process has been especially designed to achieve the following goals: maximizing the recovery of zinc and those valuable metals that are present in most zinc concentrates (lead, silver, gold); allowing the recovery of other valuable metals such as indium or germanium that could be present in some zinc concentrates; avoiding or minimizing the need for residue disposal in safe areas as it is the common practice nowadays in the zinc industry. Finally, the process achieves the previously related goals at a competitive cost, in line with the existing more efficient operations while using conventional equipment working under atmospheric conditions. The new process can be easily implemented in those smelters using the jarosite or goethite processes as well as in those smelters using direct leaching as a part of the processing facilities. A study has already been conducted on the use of jarosite in the cement manufacturing process, in the raw mix preparation as well as for a set controller. It shows that use of clean jarosite in the manufacture of ordinary Portland cement can result in improved quality of the clinker. Jarosite showed compatibility to influence the burning characteristics of the cement raw mixes. The presence of SO3 bearing mineral phases such as natrojarosite showed the suitability of clean jarosite for use as a set controller in cement production.INTRODUCTION Iron is by far the most abundant impurity accompanying zinc in its concentrates, and consequently, iron residue disposal is a major environmental concern for many zinc smelters in the world. This is especially true during the last 30 years when environmental restrictions became more and more strict. Much research work has been carried out during the last 30 years to try to find a solution for this important issue, but with little success. Only the jarofix process represents a partial solution to this problem as jarofix is stored nearby the smelters with certain limitations as a non-contaminant residue. However, it does not avoid the need to dispose of an important amount of residues every year, representing an environmental liability. Meanwhile, the number of countries limiting or banning the disposal of iron residues generated by the zinc smelters is growing, so that the solution to this problem is becoming an urgent matter right now. At the same time, the lack of appropriate available land for iron disposal is also a major concern in many cases."

Jan 1, 2016

By Cancelli Paolo, Bragonzi Gianluca, Pelizza Sebastiano

"In May 2015 the New Monte Bianco aerial cableway, operating on the Italian side, have been completed. It connects the lower station in Pontal d’Entreves (1300 metres above sea level (m a.s.l.)) with the intermediate station at Pavillon de Mont Frety (2160 m a.s.l.) and with the top station at Helbronner Peak (3460 m a.s.l.). A new underground link between Helbronner Peak and New Torino Refuge has also been built. The link is divided into two different sections: the first one, a 70 meters deep vertical pit created using the “Raise Boring”, descends underground from Helbronner Peak station; the second section, a 160 meters long sub horizontal tunnel, emerges at Torino Refuge. After a first introduction focused on the general layout of the project, the paper will present the geomechanical survey aimed to evaluate the effect of permafrost on the stability of intensely fractured granitic mass. Finally, it will describe the relevant issues related to the highest construction yard in Europe (3400 m a.s.l.): difficult conditions such as extremely cold and windy weather and restricted spaces. INTRODUCTION The new cable way connects the lower station in Pontal d’Entreves (1300 m a.s.l.), close to Courmayeur, with the top station at Helbronner Peak (3462 m a.s.l.) and its territory, as well as links with France and, through the French territory, with the town of Chamonix (1000 m a.s.l.). The overall layout is divided into two sections (as shown in Figure 1): the first section, “Pontal d’Entreves – Mont Frety”, has a length of 1700m, elevation differential of 886m, a capacity of 800 persons/hour and cable cars for 80 passengers; the second one, “Mont Frety – Punta Helbronner”, has a length of 2630m, elevation differential of 1276m, a capacity of 600 persons/hour, and cable cars for 75 passengers. The new system is designed for fully rotating cable cars moving at a constant rate of 9.0 m/s. The track requires constructing special cables supports, three for the first section and two for the second one."

Jan 1, 2016

By McGill Metals Processing Centre, S. Chang, L. Calzado, X. K. Cao, C. H. Hsin, M. Isac

"Due to the increasingly stringent cleanliness requirements for final steel products, there has been a growing interest in the possible use of micro-bubbles for the removal of inclusions with diameters smaller than ~50µm, present within the steel passing through a steelmaking tundish. However, several technological barriers have prevented the adoption of this technique in industry. These are related to a) the generation of micro-bubbles in liquid steel, b) the measurement of bubble size distributions, and c) the optimization of bubble injection conditions to create micro-bubbles. In the present study, a novel Aqueous Particle Sensor (APS) system was developed for the in-situ, on-line, detection of micro-bubbles in water, generated by a newly designed full-scale ladle shroud, located at McGill Metal Processing Centre (MMPC). Measurement results from the sensor were validated against bubble size data collected through a high speed camera and post-processed through the commercial software, Image J.Control variables and orthogonal experiments were designed to assess the dependence of average micro-bubble sizes and bubble size distributions on key experimental parameters. Those chosen were the air inlet flowrate, the distance of the gas injection port from the slide gate, and the number of injection ports used. The investigation demonstrated that the APS system can be successfully adapted to detect micro-bubbles up to ~800 micron diameters. Using this novel sensor, it was shown that multi-port injection using low air inlet flowrates, closer to the slide gate, were useful in forming small micro-bubbles within the flow through the ladle shroud. The results from the APS system were compared and validated against data resulting from an optical technique. INTRODUCTIONModern industry expects increasingly stringent cleanliness requirements for final cast products. Therefore, the numbers and sizes of inclusions need to be strictly controlled in steelmaking operations. Thus, the cleanliness of steel products depends on the amount, morphology and size distributions of nonmetallic inclusions in steel (Zhang L. & Thomas B., 2003). Since large, deep, tundishes provide longer nominal residence times for liquid steel passing through it to the exit SEN’s, this can provide the ideal place to separate inclusions, and bubbles can assist by removing help attach inclusions and float them to the top surface."

Jan 1, 2016

By T. W. Camm

"Search Amazon.com using the keyword “leadership,” and you are rewarded with a list of over 144,000 titles. There is no shortage of books and articles, many of them well written, with excellent ideas. So why is there still a constant cry for effective leadership in organizations? Often, the person in charge has personal blinders that prevent them from seeing or understanding how to implement the newest leadership idea or method. Either deliberately or subliminally, there is a disconnect from learning about leadership, and actually modelling and implementing what has been learned. Some current research in leadership theory can provide insight and tools to address this issue. INTRODUCTION Let’s start with a discussion of terms. Pseudo is defined by Webster (2015) as “Being apparently rather actually as stated.” Synonyms include affected, assumed, contrived, fake, false, phony, pretended, and artificial. Antonyms for pseudo provide additional clarity, especially when we consider terms normally associated with effective leadership: genuine, natural, unaffected, unforced. A similar type from my world of academia is a pseudointellectual, “A person exhibiting intellectual pretentions that have no basis in sound scholarship” (Dictionary.com, 2015). This is a person pretending to have an interest in intellectual activities for status; a fraudulent intellectuality. The thought of applying the term pseudo to leadership first occurred to me while reading Power and Innocence by Rollo May (1972). In discussing the dynamics of power, and how the innocent are often victims of the exercise of power, especially the more aggressive and destructive types of power, he saw two types of innocence. The first he called authentic innocence, which he described as a childlike clarity that carried into adulthood. The second type he called pseudoinnocence, a type of naïveté that makes a virtue of powerlessness, weakness, and helplessness; being more childish than childlike (p. 48-50). Just as there is the potential for pseudoinnocence and pseudointellectuals, it is also possible to experience pseudo leadership. (I hope the gentle reader is not troubled by my decision to use pseudo leadership as two separate words, in contrast to the use of compound words for pseudoinnocence and pseudointellectual cited above. Since there is no official definition of pseudo leadership, I have exercised my author’s prerogative to treat it as two words, both because I think in this particular application this makes the most sense, and also I think it is easier to read). As we will see, there are numerous theories applied to leadership. What is so troubling to many of us in organizations, there are a myriad of “leaders” in companies espousing pet theories, but very few instances where the actions of these individuals match their words. This is a particularly important problem when we look at the effect this has on the day to day operations of a mine, and where effective leadership (or its absence) can have a profound impact on both productivity and safety."

Jan 1, 2016

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By Eleanor Kentish, Edward Batty, Alan Skarda

"The design of the tunnels at Bond Street Station includes a final sprayed concrete fireproofing layer. The performance of this layer was verified by a program of testing to Crossrail’s KT24 specification, which proved that a dosage of 1kg/m³ polypropylene fibers and a layer thickness of 50mm would be sufficient to limit spalling in the event of a fire. Application of this thin layer was achieved using a state of the art spraying robot, with the ability to scan the profile and automatically apply a uniform layer of concrete. To provide assurance and calibrate this spraying robot, BFK developed a bespoke survey system for checking SCL thicknesses in the field. This provided an instant independent check of the spraying robot and allowed areas of inadequate thickness to be rectified without risk of cold joints. This paper describes the practical application of the fireproofing layer and how design compliance was ensured. INTRODUCTION Fire is one of the most serious risks to a tunnel. The nature of tunnels — being long enclosed spaces — can increase the intensity of a fire, and make fire-fighting and rescue operations difficult. The damage that can be caused has been demonstrated by a number of historic tunnel fires, such as the Channel Tunnel fires of 1996 and 2008, and the Mont Blanc Tunnel fire in 1999. Without any intervention, the high temperatures in a fire create thermal stresses and a build-up of vapor pressure within the pores of concrete, which eventually exceed the tensile strength and trigger explosive spalling. Spalling exposes the core of the section to severe temperatures, leading to a loss of concrete and steel reinforcement strength or further spalling of successive layers. The concrete used in tunnel linings is particularly susceptible to explosive spalling, due to its low permeability achieved by the addition of microsilica (Bailey 2011). The sprayed concrete lined (SCL) tunnels on Crossrail have been designed to resist the worst anticipated fire in operation, in order to prevent collapse and minimize damage to the structure. The design called for a system of passive fire protection, the efficacy of which was validated by the contractor through a testing regime. It was critical that the application on site reflected the test conditions, which demanded special control of the profile and thickness of the lining. In order to meet these constraints on tolerances and quality, BAM Ferrovial Kier joint venture (BFK) developed a reliable method of working with the Meyco Logica spraying robot, and a bespoke survey system for accurately checking thicknesses in the field. These innovations are the focus of this paper."

Jan 1, 2016

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By Yoichi Shimada, Katsuyuki Nishida, Shinichi Takahashi, Yasushi Okada, Yohei Nakamichi, Kazunori Oshiro, Taichi Terui, Sigehiko Sugie

"Temporary retaining walls are ordinarily used for tunnel construction work conducted using the opencut construction method. Retaining walls in such instances are typically installed vertically. However, shoring (such as struts and king posts) is required to ensure the stability of retaining walls in cases of excavation work to depths that exceed approximately 4 m. A new design and construction method that focuses on the effectiveness of retaining walls that are installed on an incline was studied with the aim of improving construction workability by omitting shoring. The inclined braceless excavation support (IBES) method, which was developed for use with the inclined buttress method, requires no shoring, even for deep-open-cut construction work and can be applied to deep excavation work on ground with a high groundwater level. This method has been applied at six work sites in Japan in recent years. This paper introduces the IBES design and construction method and presents verification results based on the design method, a model experiment, finite element analysis, and measurements obtained during construction work.INTRODUCTIONBackgroundIn the past, temporary retaining walls used in open-cut construction work have been installed vertically, and shoring (such as struts and king posts) has typically been used to ensure the stability of these retaining walls when the excavation depth reached 3–4 m. However, shoring interferes with structures built within excavations and requires box-outs and penetration sections in the structures, as well as concrete joints that raise concerns about their impact on the watertightness and long-term durability of structures (Figure 1).Shoring also narrows the space available for conducting construction work and reduces construction work efficiency, and the installation and removal of shoring increases the construction duration and cost. As a result, there has been a demand for ways to reduce or eliminate shoring to improve the quality of structures and construction work efficiency."

Jan 1, 2016

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By Olivier Kraft, Olaf Kortz

"Project-specific optimized tunnel boring machines represent the spearhead of technological progress in tunneling because with their use, very long-lasting, high quality tunnel structures in almost any geology, depth and topography can be produced with a high degree of automation. The mechanized excavation of tunnel structures ensures the greatest possible environmental protection during tunneling itself. Professional, systematic and high quality rebuilds and reuse of already proven equipment also ensures maximum efficiency in the use of materials and energy resources. It offers an enormous potential for a highly optimized environmental balance. Here the manufacturers of tunnel boring machines and their users in particular have a duty to ensure transparent, high quality and binding standards in the entire rebuild cycle and in the refurbishment management of innovative tunneling technology. This paper deals with the comprehensive processes with rebuild levels of tunnel boring machines and highlights some exemplarily implemented projects. 1 INTRODUCTION All over the world, the number of tunnel boring machines (TBM) in which equipment rebuilds from previous projects are re-used has increased over the last few years. This text presents the technical and economical aspects of this market development. It also takes a look at the practical implementation of rebuild measures. The ""ITAtech Guidelines on Rebuilds of Machinery for Mechanized Tunnel Excavation"" from 2015 lay down the requirements that the machine manufacturers must meet. 2 ECONOMICAL AND ECOLOGICAL ASPECTS OF RE-USING COMPONENTS The globalization of the construction sector and the consideration of environmental aspects promote an increased re-use of machines and machine components. Nowadays, large-scale construction projects are often carried out by international joint ventures of several individual companies that are established specifically for this purpose. After the completion of the project, the joint ventures are dissolved and they liquidate their project-specific equipment, such as tunnel boring machines. Today, it is much more uncommon for such machines to remain permanently in the possession of construction companies. Joint ventures offer TBMs on the free market, or they exercise contractually agreed repurchase options with the manufacturer. On the whole, this increases the number of re-usable components or complete tunneling systems available on the market."

Jan 1, 2016

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By M. Maccagni, J. Nielsen

"Engitec developed the EZINEX® Technology some years ago to recover zinc from oxidized secondary sources. This process works at neutral pH and can take into solution any kind of metal, but iron is rejected and remains in the leach residue. Engitec has also developed the FLUOBORATE System, which is able to recover lead and copper from relevant concentrates. Some iron is leached into solution, but it is controlled through a solution purification bleed treatment. In this paper, we present the two above mentioned technologies. They are very different with regards to the chemical environments and the methods used to control the build-up of iron in solution, but both systems are suitable to treat iron bearing feeds.INTRODUCTIONIn the design of hydrometallurgical processes, the most important issues are the water balance, the filtration and the control of impurities. This is particularly important when the process includes an electrowinning unit. Iron has been one of the most problematic elements to remove, especially in acidic environments.Engitec Technologies has developed several hydrometallurgical processes divided in two different electrolyte lines: the Fluoborate Technology for the recovery of lead and copper from primary and secondary sources and the Ammonium Chloride System based on a chloride electrolyte for the recovery of different non-ferrous metals, among which zinc and lead are the most important. In both cases, iron is present in the feed and needs to be eliminated from the solution. It is not a problem for the quality of the metal produced, but when present in solution, it consumes the basic electrolyte reducing its free concentration which is very important both for both the leaching and electrowinning unit operations. Both process systems are very peculiar, the fluoborate case being much more intriguing."

Jan 1, 2016

By Elbasher M. E. Ahmed, Indresan Govender

"A mechanistic model of axial charge segregation in rotating drums is presented. We show that granular material composed of different frictional properties diffuse into axial bands as a consequence of concentration fluctuations in the free surface layer that is caused by friction-limited mobility. A Bagnoldian stress assumption ensures an asymmetric free surface profile thereby providing the essential ingredients for the evolution of axial bands and the subsequent band coarsening observed in the literature. The formulation is sensitive to the boundary conditions of tumbling mills, including particle size and density, mill speed, inter-particle bulk friction, end wall friction and drum geometry (length and diameter).INTRODUCTIONA mechanism to fully describe the axial segregation of charge in a rotating drum remains elusive to the mineral processing industry. With regard to low aspect ratio mills (like ball mills), current thinking favours the use of closed circuit mills with correspondingly low residence times to offset the completely random contact probabilities between particles and balls (Wills & Napier-Munn, 2006). Conical end caps are argued to exploit the centrifugal force to achieve a regular gradation of ball size along the mill with larger sizes at the feed end and smaller ones closer to the discharge. However; segregation along the length has been observed in the absence of conical end caps (Oyama, 1939; Levine, 1999): In these investigations, sufficient differences in the particle’s mechanical properties (particle size, density, shape, surface roughness) was enough to successfully achieve axial segregation. Figure 1 shows the segregation of a bimodal distribution (by size) into bands of larger (darker colour) and smaller (lighter colour) particles."

Jan 1, 2016