Search Documents

By J. Kemeny, K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in an area of the mine that contains argillite and is relatively homogeneous. This process also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for argillite will be updated as more tests are conducted, and the model will be extended to the four other primary rock types at the Asarco Mission mine.

Jan 1, 2011

By Yi Luo

Subsidence events occurring above inactive room-and-pillar (R&P) mines, including abandoned mines or sealed portions of active mines, are classified as unplanned subsidence, because of their timing and distribution are unpredictable. When investigating such subsidence cases, many uncertainties exist and disputes often focused on whether the observed structural damages are caused by mine subsidence or other natural or artificial causes. However, solid evidence to identify the cause is often lacking. In order to conduct a complete and impartial investigation, thorough knowledge of subsidence theories and other ground control topics, as well as broad experience, are required.

Jan 1, 2011

Grade uncertainty can have a number of important implications for a mining operation. One of the most significant risks in not considering grade uncertainty in planning is the over or under allocation of processing or mining capacity when compared to realised grades. This could lead to wasted capital expenditure or missed opportunities to add value. This paper demonstrates a method that optimises production capacity and mining schedules in the presence of grade uncertainty. Applying this method to the case study of a nickel deposit recommended a reduction in processing capacity, an increase in mining capacity and more extensive utilisation of stockpiles than optimisations completed with traditional methods. As a result, average NPV improvements of between seven per cent and 27 per cent were gained.

Dec 6, 2010

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

Enterprise Optimisation is a methodology for increasing the value of mining and mineral processing operations through better long-term planning decisions. It involves a combination of ten mechanisms which deal with decisions at different stages of the value chain. A decision made at any point in the chain potentially affects the decision for all other points in the chain. The key, therefore, is to optimise them simultaneously. The Enterprise Optimisation approach can be shown to produce increases of five per cent to 35 per cent or more in net present value (NPV), even when several optimisation methods have already been applied. This paper steps through an example case study, illustrating the effect of each mechanism and how they can work together to develop greatly improved results. This example results in a series of counter-intuitive outcomes, which challenges conventional management practices and typical organisational objectives based on organisational silos.

Dec 6, 2010

In-pit crushing and conveying (IPCC) is being increasingly considered as an alternative to traditional truck-shovel mining methods. The move towards IPCC is driven by a number of factors including the potential to reduce greenhouse gas emissions, the availability of skilled labour and the need to increase extraction rates to levels that present significant challenges to traditional methods.When considering the relative performance of IPCC and truck-shovel methods, the outcome can be inadvertently impacted by either the use of different simulation approaches, or techniques that do not adequately model the processes in sufficient detail.A simulation approach is proposed that models both IPCC and truck-shovel using the same software platform and is capable of functioning at a wide range of resolutions from life-of-mine scale through to second-by-second asset tracking level. The simulation framework also holds models of processing equipment and hence the mining simulations can be extended to gauge the impact on downstream plant.The approach, known as mine-process operational simulation (MPOS), can be tailored to the level of information available and hence the type of study required, ie order of magnitude, prefeasibility, feasibility, or detailed design.Using information from block models and a range of detailed equipment and process models, MPOS can span major system discontinuities, typified by the mine-plant interface, to allow the estimation of final mine and plant product specifications.

Dec 6, 2010

Many problems result when coal mine shafts are built in complicated geological conditions and serious shaft lining ruptures have often occurred in the eastern part of China since 1987. Grouting is applied as one of the major measurements for shaft lining ruptures. However, as the general location of reinforcement grouting for shaft lining is deep in or near the bottom aquifer, while using cement grout as the grouting material, the grouting mostly belongs to fracturing grouting in deep alluvium. In these conditions, the mechanism and behavior of fracturing grouting has not yet been understood. From these points of view, this paper describes the mechanism of shaft lining rupture and fracturing grouting and then discusses the effect of grout injection on the stability of shaft lining by means of numerical analysis and field data obtained so far.

Dec 6, 2010

The selection of the mining fleet can have as much of an effect on the efficiency and effectiveness of an operation as the mining method. This is not to say that inefficiencies are only attributable to inappropriate equipment selections, these aspects have many factors but are not the subject of this paper.This paper will give an overview of equipment selection processes that have been utilised to date. It will also look at the increase in application of study programs/simulations from an aspect of accuracy, as well as the importance of enabling the analysis of multiple sensitivity scenario planning. An aspect that is increasingly important in project planning with commodity market movements.Another aspect that is increasing in popularity is that of automation, what effect does this have on equipment selection? What additional aspects need to be taken into consideration when assessing Automation of equipment from the beginning of a project as well as introduction into an operating mine?Once the selection process has been finalised and equipment implemented, how do we, as an industry, 'close the loop' through analysis of estimated versus actual equipment application?

Dec 6, 2010

Failure of rock materials is a process of crack propagation. Crack initiation takes place when the crack tip stress intensity K reaches a critical value called fracture toughness, K1C. The rock fracture toughness is known to be affected by the surrounding environment such as temperature, confining pressure and humidity. In order to examine the effect of humidity, a series of semi-circular bend tests were performed under various water vapour pressures in a rock material that is known to be anisotropic. Water vapour promotes stress corrosion of rock and therefore the fracture toughness was found to have a decreasing trend with increasing water vapour pressure. The rate of decreasing the fracture toughness depends on the microcrack density that promotes the migration of water vapour into the rock. Also in an anisotropic rock, the fracture toughness depends on the direction of crack in relation to the anisotropy of the rock material.

Dec 6, 2010

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

This paper describes new research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. The effort aims at increasing the overall rate of roadway development as well as providing a safer working environment for underground mine personnel. The activity is funded by the Australian Coal Association Research Program (ACARP) and forms part of a larger underground development initiative, known as the CM2010 project. The CM2010 is managed via a consortium of leading mining industry representatives through the Roadway Development Task Group (RDTG). The Task Group has identified three research areas requiring new development in order to realise the CM2010 project objectives: self-guiding (autonomous) continuous miner capability, an enhanced drilling and bolting process and improved mesh deployment. CSIRO's primary role in the CM2010 project is in the development of the autonomous continuous miner guidance capability.This paper reports on outcomes achieved at the half-way mark of a three year research and development project. It details the technical developments undertaken towards demonstration of a 'self-steering' capability to enable a continuous miner to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the continuous miner in real-time. Testing and validation of the guidance system solution has been implemented using a combination of an instrumentation-grade inertial navigation unit and radar technology. Comprehensive performance evaluations have been conducted using a scale skid-steer mobility platform known as the Phoenix. Results achieved to the present stage of the project are highly promising and suggest that an automated self-steering functionality is achievable under production conditions. This new outcome represents an important move towards implementing a step change improvement for future underground roadway development.

Dec 6, 2010

Hydraulic mining shovels can be successively used at open-pit mining operation in severe climatic zone with air temperature interval from -700C to +450C typical for some northern region of the world particularly of Russia, Canada and Sweden, if they would be equipped by special preheating facilities for their diesel engine, water, hydraulic oil and lubrication systems. All shovels manufactured by the Komatsu Mining Germany GmbH for operation at ambient air temperatures down to -50¦C have cast and forged structural design elements, bolted connections made of special steel grades, electric cables with special insulation, flexible high-pressure hoses manufactured by ICE-Champion with connectors made of special steel grades.Generally at the temperatures below -25¦C the ordinary machine has to be stopped, the attachment should be placed in the parking position, the generator should be switched on, or the external electrical power supply connected, for the preheating equipment. For rapid start-up in winter after a long shutdown of a hydraulic shovel, there is a procedure for preheating of the main systems. It is applied for the following systems: engine cooling system, engine oil, hydraulic oil, pumps and drive motors of the propel gears, electric cabinets, machinery house, especially near the ventilation inlets and outlets.Start-up of the main drive engine is permitted at a hydraulic oil temperature of -20¦C, when it has a viscosity of 1000 cSt. In this case the rotation speed of the diesel engine crankshaft is lower by two times than the nominal value and this is the most favourable condition of start-up of the engine and hydraulic pumps and motors, which work with half of their rated rotation speed until the hydraulic oil reaches a viscosity from 100 to 10 cSt. After that the hydraulic system and the entire shovel begin to operate under normal conditions.

Dec 6, 2010

Underground mine planning is characterised by a series of designs, starting with prefeasibility and culminating in operational. Information on the mineralisation and geotechnical conditions is available in increasing levels of detail, as development occurs. In the recently completed AMIRA Planning and Rapid Integrated Mine Optimisation (PRIMO) project, a methodology for producing good strategic and then tactical designs using new optimisation tools, was developed. At the strategic level, fundamental decisions must be made such as those relating to cut-off grade, bench heights, mining methods, access and haulage systems, properties of the mill, etc. The inputs are the block and financial models, geotechnical data, infrastructure and production costs, etc. Stope definition for strategic designs includes bench RLs (relative levels), orebody envelopes, and design and placement of amalgamated or simplified stopes. If multiple mining methods are under consideration, then stopes need to be associated with these. Access design must take into account decisions such as declines versus shafts, a template for level layouts and the topology of the access network. Some of the geotechnical and physical constraints are relaxed for strategic design stages. Strategic scheduling is high level, from a month to a year at a time. In the PRIMO project, software tools have been developed enabling the mine planner to rapidly produce a large number of such strategic designs. After the designs have been evaluated, the highest value designs are chosen and a small number of these can then be further refined at a tactical level. For these designs, the first step is determination of all stopes meeting physical and geotechnical requirements and constraints, allowing for complex stope shapes. Next, detailed layout of the mine access network is obtained, satisfying all operational and geotechnical constraints. Finally, more detailed scheduling is performed, over shorter time periods. The Melbourne University group has focused on optimal access design. In particular, the access network is optimised for minimum cost, taking into account the cost of haulage and development over the lifetime of the mine. Costs vary over the different parts of the network depending on the quantity of haulage and so a weighted network optimisation problem has to be solved. We have developed two software tools for this task, decline optimisation tool (DOT) and planar underground network optimiser (PUNO). DOT produces an optimal network of declines and crosscuts connecting access points on the levels to a portal or break-out point from existing infrastructure. PUNO designs the level layout, including footwall and hanging wall drives, development drives and connections to vent raises. A survey will be given of the capabilities of DOT and PUNO when used on some recent case studies. Our current goals include incorporating some aspects of ventilation design and modelling the development costs when additional ground support is required. This is an abstract only. A full paper was not prepared for this abstract.

Dec 6, 2010

Thermal method of diagnostic as a nondestructive monitoring is based on data logging of infrared radiation from heated surface or from the associated thermal field. Monitoring of gearcases and motors hidden faults, such as, bearing degradation (deep-seated wears and tears, fretting wear, spalling and jamming solids of revolution) is closely related to high variations in temperature. The use of portable thermal imaging devices provides considerable advantages due to: easy remote access to the unit under test even when it is operating; minimum time required to obtain information and an opportunity for a real-time diagnosis of the tested subject's condition.

Dec 6, 2010

Mine planning includes equipment selection as a subprocess because aging equipment must be replaced to maintain or improve productivity levels. The criteria used for decision-making in mine planning and equipment selection are often inextricably linked and inherently contradictory. For example, financial wisdom demands that development, which is an expense and locks up capital, be deferred as far into the future as possible yet on the contrary technical knowledge suggests that developing well ahead of stoping is practically desirable because it generates additional geological information required to improve planning of the unmined portion of the orebody and create better operating flexibility. Consequently, mine planning professionals have to delicately balance all decision criteria when executing mine planning in order to achieve optimal mineral extraction or when selecting equipment, so that capital is optimally deployed. These two processes can therefore be characterised as belonging to the multi-criteria decision analysis (MCDA) type of problems. MCDA problems are alternatively referred to as multiple attribute decision-making (MADM) problems and belong to a broader group of problems called multi-criteria decision-making (MCDM). There is now a gradual recognition and application of MCDA techniques in the minerals industry. This paper explores the theory, current and potential application of these techniques in decision-making in the minerals industry.

Dec 6, 2010

Generating short- and long-term mine production schedules in isolation and independently from each other means that only a local optimum can be achieved when each scheduling phase is carried out. The globally optimal solution however, can be achieved when integrating scheduling phases and accounting for the interaction between short-term and long-term activities simultaneously. This paper addresses the task of integrating short- and long-term production plans by combining the short-term objective of minimising deviation to targeted mill feed grade with the long-term objective of maximising net present value (NPV) into a single mathematical model. A case study is presented which compares the present values of the same stope data set scheduled via separate long and short-term models and than by the proposed integrated model which applies a predetermined penalty for each tonne of metal deviation to target for the respective ore tonnage being processed. This allows an operation to obtain a globally optimal scheduling regime when taking into consideration the cost and loss of value resulting from fluctuations in grade to the mill over the short-term.

Dec 6, 2010

Precision surface mining is increasingly occupying a significant role in open pit mining. Improvements in technology now allow continuous surface mining of material well above 140 MPa (20 300 psi) efficiently and cost effectively when compared to drilling and blasting/primary crushing methods. These include the elimination of the use explosives and primary crushing, the ability to precisely extract the ore from the waste, or separate ores of varying chemistry and mine thin seams and non-homogenous orebodies cost effectively. In addition, precision surface mining extends the useful life of a mine by extending the mine boundaries. It can expand production capacity in existing mines and is particularly cost effective in greenfield start-up mines. Precision mining techniques result in higher percentage recoveries. This paper reviews several of these techniques for the Terrain Leveler« surface excavation machine (SEM), and shows their impact. Vermeer's current approach to precision surface mining is utilisation of the T1255 Terrain Leveler SEM. Several units have been proven in round-the-clock, seven day operations throughout the world. Among other innovations are design simplicity, stability, maneuverability, rear-mounted tilting drum and top-down cutting. The impact of these items are discussed in more detail in the paper. After a detailed analysis of the importance of machine availability on overall mine performance, Vermeer has extended its equipment line to include a direct-drive option for its T1255 Terrain Leveler SEM. In addition, improvements in dust suppression are presented. While the T1255 Terrain Leveler SEM is of optimum size and cost in small and medium sized mines, Vermeer has recognised that larger mines require larger machines with increased capacities. Vermeer will prototype the T1655 Terrain Leveler SEM later this year. Specifications of this machine and up-to-date preliminary results are presented. A discussion of the role of each machine size and driving mechanisms are included. Finally, the next stage in Vermeer's providing solutions to the surface mining community will be described - a continuous loader. The impact on current mine planning is presented using a detailed computer program developed for studying the impact of loading techniques and higher production rates on mine plan optimisation.

Dec 6, 2010

By N S Melkoumian

While improvements in occupational health and safety (OHS) in the mining industry have decreased fatalities and accidents, little attention has been paid to the cultural confound of 'safety' in the increasingly multicultural mining industry. Occupational health and safety processes often contain assumptions of cultural understanding that may not be shared or understood by mining employees. There are potentially dangerous and costly implications of cultural difference in the mining environment. Some people have been enculturated with high levels of anxiety concerning catastrophe and uncertainty while others have a more laissez faire attitude to accidents and disaster. The level of cultural anxiety about uncertainty can be a major factor in the acceptance of OHS processes. OHS manuals based on a comprehensive set of rules and procedures may assume that the authority of 'rules' is shared by all employees regardless of a variety of cultural understandings when this may not be the case. Similarly, cross-cultural employees may not share a background or acceptance of expensive technological innovation and so resist/avoid the application of new safety equipment. Then too, OHS staff may not realise the significance of religious belief or personal responsibility on employees' attitudes to safety in the workplace environment. A lack of consideration of these cultural elements could have fatal and expensive results. This paper explores the impact of cultural difference in the understanding of OHS in the Mining Industry, presents a model to improve the understanding of the cultural confound in safety, improves analysis of OHS in practical multicultural situations, provides assistance for those involved in OHS training and may become a basis for developing OHS policy and procedure.

Dec 6, 2010

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010