Search Documents

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By D Olivier

De Beers' Finsch Mine is situated in the Northern Cape province, 170 km northwest of Kimberley. The concentrator facility, designed and constructed by Bateman Engineering, was commissioned in 1967 and upgraded in 1979 using diamond liberation and extraction technology available at the time of design. Since then significant advances in diamond processing and technology have been made and these -have been incorporated into the new main treatment plant and recovery plant flowsheets, making diamond liberation and recovery from the Pre-1979 dumps a viable economic option at Finsch."

Jan 1, 2010

By J. J. Carlson

An important factor in filtration is the zeta potential of the particles. Since zeta potential is a function of pH, it was hypothesized that adding CO would lower the pH and zeta potential. A reduction in zeta potential should enhance the flocculation and increase the filtration rate. This paper describes the effects CO on the zeta potential of both pure hematite and samples of hematite concentrate from an iron ore processing plant. A significant shift in the zeta potential, as a function of pH, curve was observed. These results point to an alteration of the particles mineralogy, not just a shift in pH.

Jan 1, 2010

By R. L. Levens

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface area exposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 2010

By Thomas M. Barczak

This U.S. Bureau of Mines study evaluates factors that influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: longwall panel, powered roof supports, and gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from convergence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data sumest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 2010

By L. MacHue

Sulfur containing collectors have been shown over the years to function as strong, selective and non-selective sulfide mineral collectors. Unfortunately, the majority of the widely known sulfur based collectors are of low molecular weight, volatile and subsequently, possess an objectionable odor. Higher molecular weight sulfur based collectors (C9 and higher) are significantly less odiferous due to lower volatility and lower vapor pressures. In this study, a specific proprietary higher carbon number collector, Orfom® MC 37, was blended and used successfully to recover 2-3% additional molybdenum in a laboratory flotation system, when compared to a standard collector blend. Copper recoveries were also positively affected. Further testing is required to give additional conditions favorable to increased copper and molybdenum recoveries, but indications at this time show the proprietary sulfur based collector blend to be a selective collector of molybdenum, while providing a significant increase in copper recoveries.

Jan 1, 2010

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c&apos; = 340 kPa (49 psi) and f&apos; = 24°. Residual strengths were determined to be c&apos;r = 0 and f&apos;r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.070 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70° C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 to 1,000 ms gave the following results: Ag concentrations decreased from 34 to 0.1µg/mL, Au concentrations decreased from 54 to 0.2 µg/mL, and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 2010

By D. H. Carlson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory-grade instruments. Concentrations of CO and CO2 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for CO2. EMA¬ measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO2 differences are related to the method of calculating the EMA&apos;s dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA&apos;s unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 2010

By Lightfoot. Nicholas, Na Liu

"Mining in multi-seam workings has been undertaken for many years in the VK Remnant pillars above and/or below current working areas have an important influence on retreat gateroad conditions at five of the remaining six deep coal mines. These interaction effects need lo be predicted ahead of mining so that longwall panels can be positioned to minimize roadway damage and to identify areas where additional support should be installed early into competent strata when and where it is most effective.Currently, three-dimensional elastic stress analysis using MAP3D is undertaken to predict local vertical and horizontal stress magnitudes during gateroad development and in front of the face on retreat. The predicted stress fields are often used as input to FLAC for roadway modelling.Using Maltby Colliery in South Yorkshire as a case study, this paper illustrates the MAP3D approach, together with its current limitations and uncertainties. Possible future improvements in the analysis method are proposed and the authors would welcome comments on these, or suggestions for alternative approaches.MODELLING OF MULTl-SEAM LAYOUT & MULTI-SEAM INTERACTIONThe remaining large coal mines in the UK arc operating at depths of 800-1, 150 m (2,625-3,773 ft). Production panels are now mined on retreat after the accompanying single entry access roadways have been completed. These gateroads are typically supported with a system of steel rock bolts and cable in the roof and steel bolts and glass re in forced polymer (G RP) dowels in the sidewalls.In addition to new panels being mined in the vicinity of old goafed districts, a significant amount of extraction has usually already taken place in coal seams above and/or below the current working areas. This means that there is also interaction between the current workings and the remnants of the old workings in other seams. As a consequence of the mining methods employed, old workings can have a complex geometry compri ing collapsed and partially collapsed excavations intersper ed with small and large pillars of unmined coal. The unmined coal pillar act as stress concentrators that carry the overburden load while the mined out excavations create stress shadows of varying degrees depending on how much collap e and reconsolidat ion has occurred. This is illustrated by a simple elastic model as shown in Figure I."

Jan 1, 2010

By P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown&apos;s modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers&apos; Z2 measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 2010

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010

By P. Burke, V. Vuaroqueaux, A. Doyle, C. Petit, Kipouros. G. J.

Magnesium and its alloys are attractive for use in automotive and aerospace applications because of their low density and good mechanical properties. However, difficulty in forming magnesium and the limited number of available commercial alloys limit their use. The present work reviews the efforts to improve the attractiveness of magnesium through non-traditional processing, and presents results of current work on producing magnesium alloys via powder metallurgy (P/M). P/M can be used to alleviate the formability problem through near-net-shape processing, and also allows unique chemical compositions that can lead to new alloys with novel properties. The surface layer formed on the Mg powders during processing acts as a barrier to diffusion and sintering is problematic. The layer contains oxides, hydroxides and carbonates of magnesium, formed by reactions with the atmosphere. There are several means to possibly overcome this barrier. Alloying additions have been identified that may promote surface layer disruption during sintering. Processing variables such as sintering atmosphere may reduce the layer or allow the formation of less detrimental compounds. Post-sintering processes such as hot working may disrupt the layer and improve density. The experimental effect of all these processing parameters is presented in this paper.

Jan 1, 2010

By Gary L. Hundley

As part of the U.S. Bureau of Mines program to reduce the Nation&apos;s reliance on foreign supplies for critical metals, a procedure was devised to separate and recover critical metals from mixed and contaminated super alloy scrap. The process uses both pyrometallurgical and hydrometallurgical methods to treat the scrap. The mixed scrap is converted to a matte containing 4 to 7 pct S by adding S directly to the molten metal. This matte is then granulated and ground to a minus 35-mesh particle size and leached with an HCI-CI2 solution. This process takes essentially all the Ni, Co, Cr, Fe, AI, and Mo into solution in a 3-h leach, leaving W, Ta, Ti, and Nb (Cb) in the residue. The Mo is recovered from the chloride leach solution by solvent extraction, and the Cr and Fe are recovered together by precipitation. The Ni and Co can be recovered individually by an existing solvent extraction-electrowinning process. The W is recovered by a caustic leach of oxidized Cl2 leach residue.

Jan 1, 2010