Search Documents

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By S. Angioletti

This paper addresses strategic investment decisions when they are nested in a project development format where each project is implemented in phases and each phase is approved to move on to the next phase only if certain technical and economic requirements are met. This configuration is sometimes referred to as a ?Project Portfolio?. Mining companies maintain project portfolios in their exploration investment plan. This study proposes a procedure to best manage an exploration project portfolio including technical and economic uncertainties. The procedure may support decision makers in a simple and intuitive way, while maintaining the rigor and precision required by the rather large amount of financial resources typically called for by mining projects. The procedure was tested in a real case study of a gold mining company and its exploration projects portfolio. The procedure uses the following approaches: i) investment valuation methods under technical and market uncertainties based on Option Pricing Model, Real Option Theory and Option Space; ii) portfolio management and Stage Gate®1 method; iii) Monte Carlo simulation.

Jan 1, 2010

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By D. Sager

Middleburg Ferrochrome (MFC), a company in Samancor Chrome, commissioned a new ferrochrome smelter in March 2009. This is a 60 MW DC-arc furnace with a DC power supply for the smelting of Transvaal chromite ore fines. With the benefit of 12 years&apos; experience with this technology while operating a 44 MW DC-arc furnace, MFC mitigated all known challenges and considered up-scaling risk in the new plant, which had a rapid ramp-up to full power in 02 of 2009. Good operating practices, as made possible by robust equipment selection, including a thyristor rectifier set of proven technology, and operation with optimal slag chemistry, leads to a safe and effective plant operation. With the optimized furnace design and a correctly sized power conditioning system, using only standard (static) harmonic filters and a correctly sized smoothing reactor, the arc furnace is not a &apos;dirty load&apos; for the utility, staying well within IEC limits for power quality. A patented arc compensation system is installed and allows for full arc position control (to compensate for magnetic field induced arc deflection) so that a symmetrical crucible is maintained, significantly benefiting refractory life. The principal benefits gained from the MFC process is the fact that ore fines are processed, without metallurgical coke, and higher chrome recoveries are achieved compared to other smelting technologies when using a DC open arc for smelting. Keywords Samancor Chrome, Middelburg Ferrochrome, ABB, smelting, DC arc furnace, arc compensation, power factor correction, anode, harmonics, thyristor, reactor, maintenance, refractory, ores, reductants.

Jan 1, 2010

By Walter K. Utt

The U.S. Bureau of Mines conducted research to develop an accurate, real-time, position monitoring and warning system for the vehicles used in surface mining. The product of this research will be technology to reduce accidents and injuries associated with the operation of surface mining haulage equipment. The position monitoring system should reduce accidents related to vehicle position and also increase the efficiency of haulage operations. This research was conducted in preparation for development of an accurate, real-time position monitoring and warning system, which notifies equipment operators when they deviate from a known safe course and are approaching a fixed hazard. A radar positioning system designed for marine applications was evaluated and a series of tests was run to determine the accuracy of the radar positioning system when used in a land vehicle. The radar position determination was compared to surveyed values. Both static and dynamic (moving vehicle) tests were conducted. The static test results were marginal and the dynamic test results were not accurate enough for the position monitoring and warning system. Although a promising technology, the system tested needs to be modified to meet the accuracy requirements of mobile mine equipment.

Jan 1, 2010

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated&apos; the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By G. Bylapudi, K. Mondal, J. Hirschi

ABSTRACT: Rock bolts are the main form of defence against rock falls in mines. Conditions under-ground are conducive to corrosion. A perception exists about American coal mines that bolt corrosion is not an issue, especially when bolts are fully grouted. This perception is not necessarily accurate due to the formation of micro-cracks as the resin sets and to subsequent rock movement that breaks the resin column’s continuity. Corrosion should be considered when designing rock bolt support in long-term excavations. This paper explores the problem of corrosion, outlines a method to determine the corrosion potential of bolts, and suggests ways to mitigate such effects.

Jan 1, 2010

Blast vibrations induce sounds within neighboring residences. A house wide vibration and sound monitoring system was installed in a West Virginia home which was subjected to blasts at varied distances and direction. Eighty-nine blast events were monitored and analyzed for this case study. Fifteen channels of data were collected including three triaxial geophones, one airblast microphone, one uniaxial geophone mounted to the wall of the house (response channel), and four microphones that recorded CD quality sound waves inside the house. Each of these channels was recorded on the same time reference and scale allowing for direct comparison of the waveforms. The response channel signal was easily separated into ground vibration induced and airblast induced movement due to the differences in their times of arrival. This response channel was then compared to the sounds recorded inside the home to determine which component of blast vibration induced the maximum sound response inside the home. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond 762 meters (2,500 feet), the maximum sound response inside the home was caused by ground vibration without exception. When airblast was identified as the dominant sound generator in the house, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator in the house, the peak amplitude of sound was not related to the amplitude of ground vibration. In these cases, sound amplitude was driven by the conditions present in the house such as loose items, doors, and windows creating sudden peaks from falling or slamming. In the same respect, sound amplitudes varied depending on where the sound was recorded. Different rooms generated very different sounds based on the contents of the room. Findings from frequency analysis showed that the frequency content of sounds inside the house were not related to frequency content of airblast or ground vibration regardless of source suggesting that residents would have difficulty determining the source of blast induced noise in their homes.

Jan 1, 2010

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine&apos;s ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By M. Robson

Water & Earth Technologies, Inc. (WET), Habitat Management, Inc. (HMI) and Chevron Mining, Inc. (CMI) together developed a solution for reclaiming steep southwest facing slopes in mining Area 12C that have historically been prone to excessive erosion, low vegetation establishment and continuing maintenance. Area 12C is located in the east wing of the Chevron McKinley Coal Mine, 27 miles northwest of Gallup, New Mexico, on Navajo Nation land administered by the Office of Surface Mining (OSM). Mining in this area was completed in May of 2007. Challenges encountered for this reclamation project included the need to reclaim graded material on a slope of 18-35% with southwest facing aspect, the presence of undisturbed rock outcropping that needed to be avoided during reclamation, the operational need to limit bulldozer pushes and the inability to import or export additional materials for construction. Two different reclamation alternatives were considered for Area 12C. The first alternative would use a traditional reclamation approach including three levels of draining terraces designed to convey water on a 3% slope to a single riprapped down drain. Terracing and down drains have been used to reclaim areas with similar terrain conditions elsewhere at the McKinely Mine and have failed to adequately control erosion (Williamson 2006). Terrace overtopping and down drain blowouts have been issues in maintenance and functionality for the mine. Maintenance routines consist of cleaning out terraces where they have filled in with sediment and repairing damaged or blown out terraces and down drains.

Jan 1, 2010

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By M. Reda

Because of the adverse environmental effect of Chromate, Molybdate ions had been investigated as replacement for Chromate and the results had shown not to be encouraging. Film deposited from peroxopolymolybdate (from reaction of Molybdenum meta, with excess Hydrogen Peroxide), are more robust than that deposited from molybdate solutions. This was shown to be due to higher fraction of Mo (IV) and Mo (V) that form from Mo (VI) in the peroxopolymolybdate deposited film than the film deposited from Molybdate solutions. The peroxopolymolybdate film contains 40% un-hydrated molybdic acid, tetraperoxodimolybdate and tetra peroxo tetra molybdate. The protective properties of peroxopolymolybdate were shown to be due to the effectiveness of the un-hydrated molybdic acid.

Jan 1, 2010

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010

In early June, Rio Tinto?s chief executive officer Tom Albanese said that he expected demand for iron ore, aluminum and copper to double in the next 15 years. Driven by global industrialization and urbanization, Albanese said during his company?s annual general meeting that to meet the demand in 2030, the additional supply required will be equivalent to replicating the iron ore output of Australia?s Pilbara region every five years, adding another aluminum production complex the size of Canada?s Saguenay every nine months and developing another copper mine the size of Escondida, in Chile, each year.

Jan 1, 2010

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010