Search Documents

By T. Lindstad, V. Myrvågnes

In the production of high silicon alloys, carbonaceous materials like coal, coke, charcoal and woodchips are utilized as reducing agents. Primarily based on historical prices of charcoal compared to fossil reduction materials, the Norwegian Ferroalloy Industry has mostly been using coal and coke (char) as carbon source. The most important role of the carbonaceous material is to react with the SiO gas to produce SiC. The ability of the reduction materials to bind SiO gas can be measured and the value is recognised as the reactivity of the carbon source. This reactivity is one of the most important parameters in the smelting process in order to obtain a high yield of metal. The reactivity of the carbon materials is directly correlated to the material properties. It is known that the rank of the coal influences the SiO reactivity where low rank is beneficial. Coals of the same rank have however proven to have varying reactivity. In order to investigate how the micro-constituents of coal influence the reactivity towards SiO gas, three single seam unwashed coals of different origin which fulfil the requirements of the Norwegian Ferroalloy producers have been chosen. As the structure in the carbonized product is a function of petrographic constitution and carbonization parameters, the coals have been separated into different density fractions. The various density fractions of the same coals proved to have significantly different petrographic composition. The coals were carbonized according to a procedure simulating the conditions the coals experience when charged to an industrial furnace. Chemical-, physical- and petrographical properties of both the coals and the resultant chars have been thoroughly examined and correlated towards the SiO reactivity.

Jan 1, 2007

By T J. Howard

At BHP Billiton Iron Ore operations, run of mine ore from the several Newman Joint Venture (NJV) mines is railed in 12 kt rakes to Port Hedland. Rakes are processed sequentially, with the lump and fines components from each rake sampled after crushing and screening. The grade of ore from the individual mines varies around consistently different means. Although a discrete sample is attributed to each rake, the sample contains some material from the following and/or the preceding rakes due to dilution by ore from the neighbouring rakes during the dumping, screening and crushing processes. Individual rake grades at the port are therefore biased according to the mine sources of adjacently processed rakes. Dilution does not affect the grade of the overall NJV product or the accuracy of port stockpile grades; however, it does limit the ability to use port rake grades to review the quality performance of individual mines and provide meaningful lump-fines algorithms and port to mine biases for individual mines, information that is useful when scheduling ore for mining. A non-linear regression model has been used to estimate the average dilution from the preceding and following rakes. It has been shown that the lump and fines samples for 12 kt rakes are each diluted within the Port process with about 8.3 per cent of the sample coming from the preceding rake and about 3.6 per cent from the following rake. This can bias the reported rake grade by up to one per cent iron. The results of this analysis have been incorporated into the daily grade scheduling system to provide more accurate individual mine grade data and consequently better decision making.

Jan 1, 2007

By N Cusworth

The development of a resource project inevitably requires the investigation of a vast range of issues across most engineering disciplines û mining, metallurgical, chemical, civil, electrical, mechanical and environmental û as well as the geosciences. It is also a characteristic feature of the resource industry that no two orebodies û and hence no two development projects û are the same. So these technical issues have to be addressed to a greater or lesser extent in evaluating any resource projectÆs development potential. Not surprisingly then, technical issues tend to predominate when assessing the development potential of a project in the process typically referred to as ædoing a feasibility studyÆ. But the principal purpose of a æfeasibility studyÆ is to determine whether a development opportunity makes good business sense, not just whether it is technically possible. Resolution of technical issues is often seen as the primary focus of a feasibility study, whereas in reality, these technical issues are the basis upon which an asset delivery and business plan is built. This is not to say that technical issues are unimportant û they are a prerequisite to the demonstration of a projectÆs viability. The feasibility study process must therefore demonstrate that not only have the technical issues been satisfactorily addressed, but also that the broader commercial, economic and social issues have been considered in the development of a comprehensive business plan, which includes an assessment of the risk-reward profile of the proposed development. This paper will present a framework for the conduct of æfeasibility studiesÆ and provide guidance to minimum standards and best practice.

Jan 1, 2007

By H. J. McQueen

Friction stir welding (FSW) generates complex microstructures in the nugget and thermomechamically affected zones (TMAZ) that have led to diverse explanations. However, consideration as an extension of microstructure development in piercing/extrusion can lead to a better understanding of flow patterns and microstructures during FSW. Furthermore, the intense strains in the nugget/TMAZ can be interpreted by comparison with ultra-high strains in torsion that exhibit dynamic recovery as extending into regions with high angle boundaries strongly serrated with spacing near the subgrain size defined by the high temperature. The subgrain diameter and extrusion pressure have been shown to be dependent on the Zener-Hollomon parameter Z (=t exp(Q/RT), Q activation energy, R gas constant) combining temperature T and strain rate E in the same mariner as for torsion and compression. Moreover, such tests exhibited steady state stress os above a certain strain Es (rising as Z increases) in which T, , subgrain diameter and dislocation spacing remain constant. Due to the subgrain boundaries (SGB, low angle <5°, i.e.,LAB), continually rearranging by migration, decomposition and reformation, the subgrains remain equiaxed in elongating grains, whose boundaries (GB) become serrated as they migrate to absorb SGB. As confirmed by straining in torsion at constant T and Z. , more subgrains bordering the greater GB area have several high-angle facets (HAB) ; these small cellular regions with a mixture of HAB and LAB facets are designated HAB-subgrains. As serrations in neighboring grain boundaries impinge, the grains pinch off becoming shorter; this occurs at higher strains as subgrain size decreases with rising Z. The pinching-off makes the neighbors thicker so the grains never become thinner than about two subgrain diameters. In conjunction with such geometric dynamic recrystallization (gDRX), GB&apos;s undergo a net migration into grains with denser substructure, enlarging those with larger subgrains. Consequently a better name has been proposed: grain dimensioning dynamic recovery (gDRV).

Jan 1, 2007

By R. P. Zahn

The need for quantitative mineralogical data to characterize ore types before they are processed is becoming increasingly necessary. Mineralogical data (modal abundances, grain size, liberation/locking characteristics, mineral textures and associations) can provide invaluable information to facilitate the identification of metallurgical issues that may arise during processing of a particular ore. This paper will discuss the use of QEMSCAN analysis in conjunction with bench scale flotation test work to determine metallurgical characteristics for several ore types that will be fed to the Morenci concentrator upon commencement.

Jan 1, 2007

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By S. L. Chen

The Kumera Technology Center developed a unique type of steam dryer for drying copper concentrate in the mid 1990s. The dryer has been chosen in several copper smelter projects since 1999. To expand production capacities, the Norddeutsche Affinerie smelter, the Pirdop smelter of Cumerio, the Toyo smelter of Sumitomo Metal Mining and the Tamano smelter of Hibi Kyodo Smelting have carried out projects in which Kumera Steam Dryers were installed. The capacity of a single steam dryer varies from 70 t/h to 160 t/h. This article summarizes the latest operation results of the Kumera Steam Dryers in these smelters and introduces the progress of the ongoing projects in Yanggu Xiangguang Copper, Guixi smelter of Jiangxi Copper, Jinlong Copper, Boliden Harjavalta, and Onsan smelter of LS-Nikko Copper.

Jan 1, 2007

By T. A. Silva, A. C. Bragança

Lime has been added to the iron ore slurry transported by the Samarco pipeline since its operation start-up in 1977.Initially, internal corrosion was the main concern therefore the reagent was used only for pH correction. Over the last ten years, though, transport of more complex slurries demanded a significantly higher dosage of lime to guarantee adequate rheology control. Several other reagents have been tested for the same purpose yet none has proven to be as effective regarding technical performance, environmental impact and cost. However, an alternative was sought so that the slurry rheology could still be controlled in case lime addition became impracticable. The objective of this paper is to present a technical solution for this matter, which takes into account environmental aspects. It consists of adding soda for pH correction and an organic coagulant as a rheology modifier. The latter is a quaternary ammonium salt which affected the slurry transport properties in the same manner as lime when tested in a laboratory. It showed no plug formation and allowed solid particles to settle, forming a loose sediment after rest. These results indicate a low probability of plug occurrence in the pipeline and the formation of a readily reslurryable sediment upon shutdown of the pumping system. Industrial tests should be performed in order to validate the laboratory results.

Jan 1, 2007

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By F. Tanaka

Copper losses to discard slag have long impacted on the profitability of copper smelters. Businesses based on the treatment of secondary materials have also revealed that copper losses are indices of precious-metals losses. Many custom smelters are thus required to obtain more reliable controls for reducing copper losses than ever before. Mitsubishi Materials Corp. has cooperated with academic research institutes in conducting research projects on the pyrometallurgical fundamentals of copper smelting systems, including mutual evaluation of magnetite behavior between synthetic and industrial slags. The state-of-the-art pyrometallurgy has subsequently been introduced to Naoshima smelter for controlling the Mitsubishi process. The revised controls function successfully and the operational results demonstrate that avoiding the discharge of solid magnetite from the S-furnace is quite effective to reduce copper losses. Magnetite behavior has been controlled over the Mitsubishi process so as to reduce copper losses while satisfying the needs of recycling businesses growing in Japan. In-situ estimation of magnetite behavior using the absorbed heat from the melts to cooling water will also be discussed.

Jan 1, 2007

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007

Aitik, a Boliden owned and operated open pit mine located in northern Sweden, will expand production from 18 Mt per year today to 36 Mt per year copper ore during 2010. The challenge for the mine operation is to double production with a planned increase of the shovel and truck fleet of only 50 per cent. This will be achieved through improved shovel and truck utilisation and productivity. In early 2005 Aitik started projects to enhance the utilisation of truck engine hours and to reduce fuel consumption. Both projects were successful, within a year efficient2 utilisation of engine hours increased from 60 per cent to 75 per cent and fuel consumption was reduced by six to eight per cent. The truck utilisation project focused on minimising idle truck hours by for example four operators on three trucks thus reducing idle engine hours to minimise lost time for breaks and shift changes. Other measures included focusing on improved dispatch usage, parking trucks when overtrucked, etc. Eco-driving was a project together with Swedish Road Administration with the objective to combine economical and environmental savings. To keep the focus on eco-driving a reward was set up for the shift team with the lowest fuel rate over rolling 15 weeks periods. Both activities included a comprehensive training program for mine foremen, dispatchers and truck operators focusing on efficient use of trucks from economic driving to optimised truck dispatching and minimising idle engine hours. Online monitoring of trucks activities and fuel consumption combined with continuous reporting gave shift foremen and management a tool to discuss and follow trends and individual shift team performance. The combination of close monitoring of mainly organisational practices and operator training resulted in significant productivity increase and lower operating costs without any capital investments.

Jan 1, 2007

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

Thermo Fisher Scientific is the worldÆs leading supplier of analysers for laboratories and process industries. The companyÆs X-ray fluorescence (XRF)-based slurry immersion probes were originally developed by the acquired Amdel Instrumentation. These analysers have found limited application within wet beneficiation plants for measurement of iron. The recent trend of renewed efforts to maximise recovery from existing resources and lower costs has increased industry interest in online analysis. In the mid-1990s the company developed online analysers (the light element slurry analyser û LESA) for slurry applications using the prompt gamma neutron activation analysis (PGNAA) method. The company has successfully installed LESA for the direct measurement of lighter impurity elements in Brazilian plants using flotation for rejection of silica. A case study is presented. The PGNAA technique has the unique ability to provide elemental analysis of bulk materials on a conveyor belt. The company released its eighth generation cross belt Omni analyser using PGNAA in 2007. Results from a recent project with sinter are presented. The Niton range of hand-held XRF analysers is also supplied by Thermo Fisher Scientific. These handy devices are finding widespread use in the mining industry to provide quick and easy analyses in exploration settings. In contrast to PGNAA this is a surface technique. A prototype for light element analysis is being tested for iron ore.

Jan 1, 2007

By L. E. Gutiérrez

A new filtration model based on porous media transport theory is presented. It predicts capacity and final moisture content in the filtered cake as a function of design and operational variables at the plant. FilterSim® is the computer code where this new model is programmed. Application of FilterSim® to ten-month operation of an industrial copper concentrate filtration plant is shown on a daily basis and using a single set of internal parameters for the whole period. Average error is less than 5%, both in capacity and moisture estimation. FilterSim® abilities to optimize industrial filtration plants as well as to estimate future budgets are illustrated with several real examples.

Jan 1, 2007

By M. Ruel

In today&apos;s highly competitive worldwide market, it is becoming extremely important for managers to make sure that all resources are used where needed the most. That way, all resources are generating added value, process control equipments are maintained in an optimal state for best performance, and final product is produced at least cost. Performance monitoring is the only way to ensure that everyone is working on top priorities toward the same goal. How can we add value to these warehouses of data? The data is there and the information is hidden; it is just waiting to be extracted. A process performance monitoring system is able to determine if a loop, a system, a unit, or a plant meets the expected performances. The system prioritizes the areas that need attention. It also provides historical reports of the plant status by areas, by loops, and by identified problems. This information is provided to different categories of users in an appropriate format for each one. The system also includes diagnostics and tools to detect and analyze problems.

Jan 1, 2007

By C. Ciriello

Six Sigma methodology, as applied within Xstrata (formerly Falconbridge and Noranda), involves a disciplined approach to managing projects, solving problems, improving performance, and leveraging information. The four (4) cornerstones of Six Sigma are the use of Philosophy (customer driven, desire to improve and discipline), Metrics (measurement systems), Methodology (scientific method and sequence of deliverables), and Tools (such as statistics, change management, and root cause analysis). This paper will outline the general steps of the Six Sigma methodology and demonstrate how each phase directly applies to a real plant metallurgical project aimed at reducing nickel losses of the rougher flotation circuit at Raglan. The main concepts of Six Sigma are described, along with the specific challenges, successes, and deliverables related to the project. It is also the authors&apos; aim to demystify the basic Six Sigma principles.

Jan 1, 2007

Mining is a business involving extraction of commodities of value to society from non-renewable resources. Consequently there is only one opportunity to extract ore from the ore body in order to unlock the value potential encompassed in the asset. It is therefore imperative that the maximum value is unlocked during the extraction programme, considering the relative wealth generated for shareholders and society, the sustainability of society, the environment and the operation. The bulk of the value that is unlocked is usually embedded in the initial design process. How do you measure sucess The most common measure of success is the return on investment, which is unlocked during the extraction process. This is usually only determined and locked-in during the study process. Another measure of success is the profitability that is achieved on a monthly basis. A further measure would be the enhancement the asset affords to the share price of the operation. Increasing focus on sustainable development requires that the impact on the society and environment received high priority as well. All these measures are largely encompassed in the cash flow and the discounted cash flows. This paper focuses on the dynamics of the cash flow and the most significant elements influencing return in investment. These include the mine design, production volume, sustainability, risk and valuation techniques. When do you add the most value? There are many different phases and definitions noted by different authors to demonstrate and standardise the study process for new projects. This paper is based on a process with 3 major components namely a conceptual study, a prefeasibility study and a feasibility study.

Jan 1, 2007

By K. Soga

DOWA has long been specialized in the treatment of complex massive sulfide ores from exploration through smelting. Its competitive advantage derived from ore dressing technology to dress and concentrate complex ore to various kinds of metals concentrates. With this technology, the company recovers as many as seventeen different nonferrous metals. Therefore, it is crucial for the environment management and recycling business both to recover valuable elements like gold, silver, copper etc. and to handle hazardous elements in safety. From this view point, the nonferrous metal industry has a potential to play an important role; that is "The Anchor of Recycling" or "The Joint of Recycling Loop". By utilizing these mining, smelting and refining technologies, know-how and facilities, DOWA became a leading waste treatment, soil remediation and metal recycling company in Japan. This knowledge is now being applied in China .

Jan 1, 2007

Zincor operates four Lurgi fluidized-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Roaster 3 was the first to be rebuilt in 2006 because its condition had deteriorated the most. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled owing to the combined effects of excessively high operating temperatures and corrosion. These were caused by the following two main factors: ?Thicker external insulation was installed during a previous maintenance shut, which resulted in an increased steel shell temperature and exacerbated the normal metal fatigue ?SO2/SO3 containing gas that had permeated the brick lining passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but when it was dismantled more damage was found, and the roaster was rebuilding from the tuyeres upwards. During there building the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007