Search Documents

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

By Chu E. Ho

Current methods of determining jet grout column diameters are highly empirical and site specific, and do not take into account the jet hydrodynamics and soil parameters explicitly. A theoretical model which describes the jet excavation mechanism is introduced in this paper, with the aim of providing an improved prediction tool that can be used in jetting design. The model is based on the assumption that the velocity distribution in the cutting jet is equivalent to that of a free jet with boundaries corresponding to the dimensions of the cavity excavated in the ground. The shape of the cavity formed depends on the erosional properties of the soil and jet expansion is limited by the resistance at the jet-soil interface. The model predicts that the limit of jet penetration is reached when the average dynamic pressure at the jet tip becomes equal to the ultimate soil bearing resistance. The reliability of the model, evaluated using results from four case histories of jet grouting field trials, is within ±15%.

Jan 1, 2006

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

Technical disputes, commercial negotiations and workplace/societal conflict are a natural part of doing business and just living itself. Conflict is everywhere û at home (between family and neighbours); in the workplace (between management, co-workers and unions), with contractors and with other companies; and everywhere at the community level, dealing with land access (pastoralists/farmers and indigenous/First Nation people), environmental protestors and NIMBY-ites - Civil Society in general. Exploration and mining companies, operating in more remote, less developed and culturally diverse regions, tend to encounter myriad areas of conflict (typically emotion-charged) and they are outlined. Dispute prevention, management and various binding and non-binding resolution techniques are discussed. The paper gives a general overview of the ADR nomenclature and framework (mediation, conciliation, expert determination, adjudication, arbitration and litigation) encouraging technical professionals to participate. Its thesis is that lawyers should not necessarily be the first port of call when problems arise between the mining workforce, contractors, joint venture partners, purchasers of prospects/mines, traditional land owners, protest groups, etc. If the matter must be litigated, the role of the expert witness is critical in pretrial planning, negotiations, mediation and litigation management, so a few guidelines are provided. Whilst dispute resolution has a legal context, the paper is written from an AusIMM technical professionalÆs perspective, emphasising practical long-lasting pragmatic solutions.

Jan 1, 2006

During the hydrometallurgical processing of the major base metals Cu, Zn, Ni and Co, the presence of iron is normally a serious complication, and iron separation from the pay metals usually constitutes one of the main challenges for the metallurgist. There are many instances, however, where the presence of iron is beneficial, or is even required. Two cases are presented where iron is required during the processing of base metals. The first example deals with the use of ferric sulphate to oxidize sulphides, more particularly copper and zinc sulphides, under atmospheric conditions. The results presented confirm that ferric ion leaching is efficient, particularly when the oxidant is regenerated during the process. The second case is the use of iron to solubilise refractory cobalt oxide minerals; examples, including pilot plant results, are presented for various ores from Africa and Central America. In both cases, this paper reviews the basic concepts involved and provides details of their application.

Jan 1, 2006

By Song Ning

The main mineral constituents of phase-transformed chalcopyrite are CuS and FeS2. CuS is more soluble than FeS2 in an acidic CuCl2 solution with presence of excessive NaCl, so that FeS2 could be removed as solid residue from a leached solution. The experimental results showed that the efficiency of the copper leaching is heavily determined by the following two factors: a) The degree of the chalcopyrite phase transformation to CuS and FeS2 b)The concentration of Cl during the leaching, specifically whether there is enough excessive Cl existed. I t was found that when the Cl in the solution is not excessive, the slowest step of the leaching is the dissolution of Cu2Cl2.

Jan 1, 2006

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By O. Leuangthong, E. Schnetzler

"The McMurray formation in the Athabasca oil sands deposits of northern Alberta is part of the world’s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine, and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modelling of the McMurray formation using modern geostatistical techniques.Geostatistical modelling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: 1) assessing the most appropriate stratigraphic transformation for optimization of the correlation structure; 2) determining representative distributions with declustering and debiasing techniques; 3) modelling spatial continuity of the bitumen grade, fines grade, water saturation, and other petrophysical variables; 4) performing estimation and cross validation as checks against simulation results; 5) performing simulation for uncertainty quantification of bitumen and fines grade; and 6) model checking of simulation results against the input data, and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed."

Jan 1, 2006

By R. K. Sidhu, N. L. Richards, M. C. Chaturvedi

Nickel base superalloy IN-738LC, strengthened mainly by the precipitation of y' phase, is extensively used in hot sections of land-based and aero gas turbine engines. Fusion welding, which is one of the most commonly used joining techniques for the repair and fabrication of superalloy components, however, finds a very limited application in case of IN-738LC components, as the alloy suffers from HAZ cracking during welding and during subsequent postweld heat treatment (PWHT). The present paper reports on the two methods studied to reduce the HAZ cracking in as-welded and postweld heat treated GTA welded IN-738LC, viz., the use of various fillers during welding, and the use of appropriate heat treatments prior to welding. The results of the microstructural analysis and crack measurements indicated that the HAZ cracking in GTA welds of IN-738LC was significantly reduced by using age-hardenable fillers with Al+Ti concentration less than that in the base metal in conjunction with a preweld heat treatment developed by the authors.

Jan 1, 2006

By L. I. Kiss, A. Larouche, V. Dassylva-Raymond

Control of the quenching capacity of the cooling water is of primary importance for maintaining the quality and recovery rate of ingots produced by direct chill casting. Industrially, this can be done using a cylindrical metallic probe undergoing rapid quenching by direct immersion in a reservoir filled with casting water. Such a test rig originally developed at Alcan Arvida Research and development Centre was modified and used to assess the role of key parameters affecting the boiling heat transfer. During the tests, the probe of the instrument undergoes the effects of different heat transfer mechanisms. An experimental study was performed in order to clarify the details of the probe-water heat transfer during rapid quenching. The heat flux along the surface was determined by mathematical modeling using the measured temperature signals, while the corresponding heat transfer regimes like stable and unstable film boiling, nucleate boiling and natural convection were identified by the analysis of high-speed video recordings. Aluminium

Jan 1, 2006

By T. Xue

429 As part of Inco's S02 abatement project for its Sudbury operations, a weak acid treatment plant (W ATP) was commissioned at the Copper Cliff smelter in August of 2004 to treat the weak acid streams generated by the flash furnaces, the MK reactor and the fluidized bed roaster (FBR) gas cleaning plants. The W ATP process was developed by Inco Technical Services Limited (ITSL) by means of laboratory and mini-pilot plant programs. In the W ATP process, the feed solution containing arsenic, sulphur dioxide, iron and other impurities is treated by oxidation and neutralization to form a stable precipitate for disposal in Inco's tailings impoundment area. During the commissioning of the WATP, a team of operations, maintenance, engineering, project and R&D personnel was formed, and the designed capacity was achieved in less than a month. Since then, the W A TP has been operating smoothly and the impurities, specifically arsenic, in the Copper Cliff smelting process have been effectively removed.

Jan 1, 2006

By T. Rahimzadeh, C. W. Trueman, S. Farzaneh, S. V. Hoa, I. Abdalla

This paper presents the shielding effectiveness (SE) of woven continuous carbon/epoxy composite materials. The theoretical and physical concepts behind the experimental results are demonstrated in details. The influence of frequency, the overlapping angle between overlapped layers and the number of overlapped layers upon the EMI shielding of composite sheets are discussed. In this work, in particular, the epoxy layers are considered as dielectric apertures of the conducting carbon fiber slab for the interpretation of the experimental results. The experimental results, using ASTM standard D4935-89, indicate that the SE can reach values greater than 90 dB above 500 MHz.

Jan 1, 2006

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

By I. Nakatsugawa

Chemical conversion coating is a process to create thin oxide/hydroxide film containing several inorganic/organic compounds by way of chemical deposition reaction. In case of the application to Mg mobile electronic housings, the film should possess a good electric conductivity while keeping adequate corrosion resistance and working as a paint base. The use of toxic/hazardous chemicals is strictly prohibited from the environmental aspects. This paper describes the recent trend of conversion coating used for Mg electronic housings and analyzes critically from the point of surface technology. The importance of cleaning process and understanding of surface microstructure are particularly emphasized with several experimental results.

Jan 1, 2006

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By Z. Farhat

In spite of advances in cutting tool technology, the understanding of the basic wear behavior and failure mechanisms needs further study. Tool wear is the main factor contributing to geometrical error and thermal damage in machined components. Manifested as a reduction in tool life, it also affects the workpiece surface finish, increases cutting forces and induces residual stresses. Furthermore, the emergence of high and ultra-high speed machining processes necessitates the investigation of tool wear under these severe working conditions. Tungsten carbide-cobalt composite material has been used traditionally as wear resistant materials for many years. One main application of this material is in cutting tools. WC-Co tools consist of hard WC particles imbedded in a tough Co matrix, which functions as a binder phase. More recently, Cubic boron nitride (CBN) tool material have attracted special attention due to its high hardness and excellent wear resistance. Boron nitride in its cubic form is known to be the hardest material next only to diamond. In this paper microstructural and tribological properties of commercial grade WC-Co and CBN cutting tool materials are investigated under high speed cutting conditions. The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Four-fold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear mechanisms are proposed and are related to the observed wear characteristics in the cutting zone.

Jan 1, 2006

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006