Search Documents

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By S. Espley, T. Nyabeze, D. Beneteau

"Many mentorship programs are available to Canadian mining industry employees. Some are company-led initiatives, whereas others are provided through educational institutions or nonprofit organizations. In 2016, a national survey was launched to gain insight into perceptions of what mentorship is, learn about available programs, and collate experiences with formal and informal mentorship opportunities. This paper outlines survey findings and delivers recommendations to industry for consideration in employee mentorship programs. In addition, mining industry leaders share their mentor/mentee perspectives. The intent of this paper is to bring awareness of best practices that can help employees grow and develop in their profession.RÉSUMÉ Les employés de l’industrie minière canadienne ont accès à de nombreux programmes d’encadrement. Certains sont des initiatives menées par les sociétés, d’autres sont proposées par le biais d’établissements d’enseignement ou d’organismes à but non lucratif. En 2016, une enquête à l’échelle nationale a été lancée en vue d’obtenir des informations quant à la perception de ce qu’est réellement l’encadrement, de découvrir les programmes proposés et de comparer les expériences aux possibilités d’encadrement, officielles ou non. Cet article présente les résultats de cette enquête et fournit des recommandations à l’intention de l’industrie afin qu’elle les prenne en compte dans ses programmes d’encadrement des employés. En outre, des chefs de file de l’industrie minière partagent leurs points de vue conseillers/protégés. L’intention de cet article est de sensibiliser les employés aux meilleures pratiques, ce qui les aidera à évoluer et à se développer dans leur profession. INTRODUCTIONThis paper about mentorship in the mining industry is based on voluntary responses to a cold survey, written and circulated by the authors. In 2016, a link to an online mentorship survey was circulated to males and females in the mining industry with the belief that mentorship programs should be available to everyone. The link was delivered via the authors’ personal networks in mining, the CIM Reporter, Women in Mining (WIM) email blasts, LinkedIn, and Facebook. This paper summarizes the answers to the survey questions. The paper is a follow up to one by the same authors (Nyabeze, Espley, & Beneteau, 2010), which was written to gain insight into why women join and stay in the mining industry, and to learn why the overall representation of women is low."

Jan 1, 2018

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By COLIN A. LAWRENCE, Anthony Del Vescovo

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2017

By Dong Maolin

A great amount of high temperature off-gas, whose maximum temperature is up to 2100?, is generated during the smelting process of electric arc furnace (EAF). The dust content, which is mainly iron oxide, of the off-gas is high and worthy of industrial recovery. The heat carried by the high temperature off-gas with dust is about 11% of the total energy input of EAF, and some even is as high as 20%. The high-temperature off-gas not only takes away a lot of heat but also places a huge burden to de-dusting system of EAF. It not only reduces the iron oxide dust recovery ratio, but also causes serious pollution problems. With the development of the iron and steel industry, the proportion of molten iron for EAF gradually increases, and even more than 30% in some cases. The increase of molten iron causes increases in the amount of EAF off-gas and heat waste. As a result the problem of dust removal is worsening [1-2]. How to sufficiently recover the sensible heat of the high temperature off-gas, create conditions for efficient dust removal, thus reduce operating costs of dust removal system and the production costs is a problem which EAF steel making companies must pay attention to.

Oct 30, 2017

By Herrmann Flor

In steelmaking process, where up to 70% of variable cost of finished product is already incurred, energy and refractory costs account for 45-50% of the cost of production of crude steel and contribute significantly to the carbon footprint of the end product. Any attempt to control and reduce these costs will automatically lead to more competiveness and reduced carbon emissions. Leading the technology for ECOPLANT (characterized by the fact that the economic and ecological benefits are integral part of our products), SMS has developed innovative solutions which can be applied to both new and existing plants alike. This paper reviews one of the electrical and automation concepts. Tackling the secondary gas cleaning system and hence being applicable to almost all steel plants, the X-Pact® Gas Cleaning Assistant optimizes the control of individual dampers based on modelling of fluid resistances of ductwork in gas cleaning system. It guarantees the best dust removal from work place at minimum energy consumption.

Oct 30, 2017

By Steven Gillgrass

Gerdau Monroe has installed and commissioned the Tallman Supersonic Carbon Injection system (TSCi™) for use in their 135-ton Electric Arc Furnace (EAF) located in Monroe, MI. TSCi™ is an innovative injection system with the primary aim of improving injection carbon delivery to the steel bath by increasing efficiency. It is proven technology with installations at numerous steelmaking facilities all over the world. Results from installation and commissioning of TSCi™ at Gerdau Monroe will be reported as well as on-going trials and optimization efforts. Standard injection systems deliver carbonaceous material from a vessel to the EAF using air where it is injected through a lance pipe or oxy-fuel burner. Using this method, material delivery to the EAF is limited by the pressure and velocity of the transport air. Loss of efficiency can be observed by looking at the quality of the injection carbon stream during operation or by measuring loss on ignition of EAF slag or off-gas system dust. TSCi™ uses a patented design and proprietary technology to improve delivery of carbonaceous material to the EAF. Using this method, savings at Gerdau Monroe were realized by reducing the amount of carbon used in each heat while maintaining or improving upon existing foamy slag practice. As well, significant savings were achieved as a result of reduced FeO content in the slag and improved recovery of iron. Additional savings can be realized by using a smaller mesh material to take advantage of lower material cost and higher injected surface area. Other inherent benefits to improved injection carbon include lower energy and electrode consumption, reduced refractory wear and reduced maintenance cost.

Oct 30, 2017

By Daniel Mapa Clemente

Processing of tin slags in reduction furnaces was studied in order to optimize tin recovery and reduce recirculation rates of slags containing thorium and uranium oxides. A theoretical approach considering a mass balance of the process was developed and adjusted by experimental results in order to predict the final slag composition. A metallic phase (FeSnSi) was discovered trapped in the slag due to high apparent viscosity, raising the FeO and SnO2 contents of the slag sample. This FeSnSi alloy is rich in tin and its recovery would help to reduce the slags recirculation. High contents of ZrO2 were found in the slag, restricting it from reaching complete fluid phase. Through an analysis of the slag in the CaO-FeOx-SiO2 and ZrO2-CaO-SiO2 phase systems it can be concluded that final slags should be modeled aiming fluid phase at working conditions and additions should be planned in order to control ZrO2 levels.

Oct 30, 2017

By Fábio Lucas da Silva

Com a queda brusca nos preços das commodities, os termos redução de custos e maior produtividade tornaram-se assuntos constantemente abordados no cotidiano das empresas, pois esses fatores representam questão de sobrevivência das organizações. Para tal, a busca por melhorar continuamente o processo produtivo em prol de garantir espaço no mercado é uma realidade e necessidade, com isto é importante que as empresas conheçam detalhadamente os seus processos e tenham maturidade para tomar decisões baseadas em dados e fatos. Assim, este trabalho tem como objetivo aplicar a metodologia Seis Sigma para investigar quais são as variáveis que mais influenciam no processo de flotação reversa de minério de ferro reduzindo o consumo do reagente coletor amina uma empresa de mineração na cidade de Itabira MG.

Oct 30, 2017

By Douglas Glenn Stalheim

Production of structural steel with a minimum yield strength of 700 Mpa produced as hot rolled coil has become increasingly popular due to cost considerations when compared to quench and temper equivalent product. This grade when produced as hot rolled coil requires the use of microalloy precipitation strengthening mechanisms. This is typically a combination of niobium and titanium microalloys. While the metallurgical concept of structural steel precipitation strengthening mechanisms has been well researched and published, actual implementation into the production process can be very challenging. In addition to achieving a minimum yield strength of 700 Mpa, in many applications additional mechanical property attributes of formability as measured by hole expansion testing along with low temperature toughness properties are now required. Achieving a balance of all the mechanical properties in a stable and repeatable performance in production using microalloy precipitation strengthening mechanisms further increases the challenges. This paper will discuss the metallurgical/process strategies required to successfully produce 700 Mpa minimum yield strength hot rolled structural steel coil. In addition, the role and goals of both niobium and titanium in this product design will be presented.

Oct 30, 2017

By Steven G. Jansto

Carbon content and continuous casting parameters affecting solidification behavior, such as super heat, mold level fluctuation, heat transfer, fine grain chill zone depth and other process solidification parameters directly influence the surface and internal quality of the steel strand. The carbon content, resultant fine grain chill zone depth, the equiaxed-columnar transition zone and the strain energy are the primary drivers that govern hot ductility behavior. These factors influence the propensity for crack formation during the unbending section in the continuous casting process. Elements such as microalloys exhibit secondary or tertiary root causes for crack formation and are not the primary crack formation root cause. This solidification research identifies that the traditional hot ductility as measured via the percent reduction in area (%RA) at elevated temperature grossly overstates the minimum ductility required to assure crack-free casting of microalloyed steels. The strain at the ultimate tensile strength exhibits a very high correlation coefficient with strain energy while an extremely low correlation coefficient is exhibited with %RA.

Oct 30, 2017

By Aitor Elorriaga Fernandez de Arroyabe

The purpose of Sinter plants is to heat iron ore fines along with fluxes and coke fines or coal, to produce a semi-molten mass that solidifies into porous pieces of sinter with the needed size and strength. Fluxes used in the sintering process need to have an appropriate size distribution and TI to avoid generation of fines, which could reduce the productivity of the Sinter. Besides, a homogeneous chemical composition and high absorption characteristics are necessary to control the basicity and to combine the flux with P, S, Si, etc, respectively. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification, being olivine and serpentine its principal minerals. It is a very homogeneous and hard stone and its main characteristics are: high hot and cold resistance to mechanical stresses, softening and melting points of a flux not of a refractory material. In addition, due to its mechanical and chemical properties, less fines are generated in the sintering process and during the handling and transportation to the blast furnace, improving the productivity of these processes. In this way, the use of PASEK Dunite allows increasing the homogeneity structure of sinter, reducing the percentage of return fines and improving the Sinter productivity.

Oct 30, 2017

By Andrea Zanon

Slitting processes have been used for many years to increase the productivity of smaller diameter deformed bars, without making major investments in the rolling mill. This technology is used mainly for the production of reinforcing bars (7-20 mm diameter), but successful applications exist also for round bar production. The multi-slitting process enables to produce up to 5 bars starting from one billet, thus increasing the productivity of the smaller products. Danieli Morgårdshammar, world leader in the supply of rolling mills for long products, has been a front-runner in slitting technology since its first applications and has recently developed, first in the world, the technology to produce 5X8mm rebar. This process has been recently applied in BRSM steel, a company based in Bangladesh which is a worldwide benchmark for slitting technology performances. This paper presents the necessary modifications which need to be considered when developing a 5-strand slitting project (and multi-strand slitting projects in general), as well as the results obtained at BSRM Steel when the process was implemented in 2016, the first rolling mill in the world rolling 5X8 mm slit rebars.

Oct 30, 2017

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017