Search Documents

By David Seaman, J-P Franzidis, Emmy Manlapig

"A new device has been developed to directly measure the bubble loading of particle-bubble aggregates in industrial flotation machines, both mechanical flotation cells as well as flotation column cells. The bubble loading of aggregates allows for in-depth analysis of the operating performance of a flotation machine in terms of both pulp/collection zone and froth zone performance. This paper presents the methodology along with an example showing the excellent reproducibility of the device and an analysis of different operating conditions of the device itself.The device has been used to investigate the froth selectivity of attached particles. Simultaneous measurements were made using a different froth recovery measurement technique in the same flotation cell. A comparison of these techniques shows that in this case, particles are selectively detached from bubbles at or near the pulp-froth interface.INTRODUCTIONA flotation cell can be considered to operate in two distinct phases or zones; namely the pulp or collection phase and the froth phase. The pulp zone is responsible for the formation of hydrophobic particle-bubble aggregates, whilst the froth phase is responsible for the separation of these aggregates from surrounding suspended hydrophobic and hydrophilic particles. Thus, the froth phase is the grade determining phase in flotation. A measurement of the bubble load (the mass of particles attached to air bubbles in units of mass/volume) will enable the analysis of the performance of both the collection zone at creating bubble-particle aggregates and also the froth zone at separating these aggregates from surrounding pulp.A measure of froth zone performance that has been used extensively in flotation research is the Froth Recovery, Rf, of a particular system. Froth recovery is defined as the mass of particles collected in the concentrate launder by true flotation as a fraction of the mass of particles entering the froth phase. The measurement of bubble load allows for this term to be calculated easily, rather than having to go through the laborious task of, for example, changing froth depths to determine this performance criterion (Contini et al., 1988; Vera et al., 1999b; Feteris et al., 1987)."

Jan 1, 2004

Both innovation and excellence are desirable attributes of education, as they are also markers in the progression of the human race, but how attainable are they? The interaction of minerals and humanity provides a special insight into the development of both criteria, from the discovery that chert cuts, through the Bronze Age and the first use of metal alloys for implements, to using coal, oil and uranium as sources of fuel. However, there have been many hiccups along the way, where excellence in one respect has meant disaster in another. Examples are in the exploitation of asbestos, and in traditionally poor work practices in mining, both contributing to the widespread public belief that minerals and mining are ecologically undesirable. Yet is this perception based on the unrealistic expectation of innovation and excellence being simultaneous qualities of any given process? Common sense born of experience indicates that the journey from one, to the other, is usually a long and often tedious process, with much trial and error before excellence is attained. In our time, the partnership between academia and industry is the usual pathway to achieve it. Even so, we should take care that innovation does not become overwhelmed by the pursuit of excellence: as history clearly demonstrates, humanity depends upon both.

Jan 1, 2004

By J. Day, Matthew X. Yao, Lijue Xue

Hardfacing overlays are commonly applied on the shroud Z-section of turbine blades for enhanced wear resistance. Among various processes that are used to apply the hardfacing overlays, the plasma transferred arc (PTA) welding process offers several advantages including lower heat input, less base material dilution, rapid process time, and reduced operating cost associated with the capability to apply materials in the powder form. The development of a robust PTA process is crucial for overlay performance and repeatability, particularly in the aerospace industry where a quality intensive manufacturing environment prevails. For this reason, the Taguchi method of experimental design was selected to develop a test plan. A 4-factor 3-level (L9) orthogonal array (OA) was used in the experiment. The L9 OA allows for a more detailed (3 level) investigation of critical process parameters, namely plasma gas flow rate, traverse speed, powder feed rate, and arc current. Two hardfacing materials, Stellite 694 and Tribaloy T-800, both Co-based wear resistant alloys, were investigated by deposition onto a cast IN738 Ni-based superalloy substrate. Performance measurements of the hardfacing deposits included deposit hardness, substrate hardness, deposit density (porosity), degree of cracking/inclusions, and a quantified visual inspection. The procedure resulted in optimized PTA hardfacing parameters for both Stellite 694 and Tribaloy T-800 on IN738 turbine blade material.

Jan 1, 2004

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004

By Ron Millions, J. A. Folinsbee, Ishwinder Grewal, Michael Fullam, Don Strickland, Tony Y. Chong

"Since milling began in 1912, the Dome mill, now part of the Porcupine Joint Venture (PJV), has been expanded several times, the most recent increasing the milling rate from 3,500 to 11,500 tonnes per day. Dome uses conventional crushing and grinding followed by gravity concentration to recover free milling gold. A cyanidation/CIP process recovers the remaining gold in the gravity tails.Over the past few years, continuous gravity improvements have increased the gravity recovery from 20% to nearly 50% of the plant feed gold. This paper describes some of the factors that have contributed to this dramatic increase, and suggests how gravity recovery can be further improved. Gravity circuit availability has been improved to >98% with the implementation of a preventative maintenance program. More Knelson concentrators have been added to the circuit, and in 2002, an Acacia Intensive Leach Reactor was installed to replace the shaking table. In 2003, the entire gravity circuit was audited to evaluate and quantify the circuit performance. The metallurgical and mechanical operating conditions of the gravity circuit are now well understood, and areas for further improvement are well defined.INTRODUCTIONThe Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. One of the goals of the JV was to use the milling capacity of the Dome mill to process ore from Placer Dome and Kinross mines in the Timmins Camp. The PJV Dome Mill utilizes gravity concentration, cyanide leaching and carbon in pulp gold circuits to recover gold. Gravity recovery has been used in some form at the Dome Mill for most of its existence, first using conventional jigs, these being replaced in 1993 by two Knelson Concentrators, one for each of the two grinding circuits in the Dome mill. Over the years more concentrators have been added to improve the gravity recovery, most recently in 2002 for a current total of five. Also in 2002, an Acacia Intensive Leach Reactor was added to process the Knelson concentrate, replacing the shaking table."

Jan 1, 2004

By W. Wallace

The aerospace industry celebrated 100 years of powered flight in 2003, and the remarkable achievements that have occurred during the past 100 years are in no small way due to major developments in materials. Modern alloys for airframes, engines and other major sub-systems have evolved through the intelligent application of new processing concepts involving melting, casting, hot and cold working, heat treatment and more recently vapour phase processing. Alloy design has evolved in parallel to allow maximum benefits to be achieved from these processing advances. However, the pace of development seems to be slowing and future gains are likely to be made by learning how to extract major value from aerospace assets. Understanding the modes of deterioration and establishing cost effective lifetimes by holistic life cycle management seem to be the way of the future. Extending component lifetimes by repair, rejuvenation and refurbishment are all viable possibilities and they offer great opportunities for Canada, which, traditionally, has been a major user of modern aerospace materials rather than a supplier. The challenges for metallurgist, physicists and engineers will be no less than in the past and should create new business opportunities for Canada. The scenario described above will be developed by calling upon examples drawn from the author's experience.

Jan 1, 2004

By Maria I. De Rosa

The major fire and fire injury findings for all metal/nonmetal mining categories for 1990-2001 are shown in tables 64-65. Table 66, partly illustrated in figure 22, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays for all metal/nonmetal mining categories by time period. For all metal/nonmetal operations (including stone and sand and gravel), a total of 518 fires occurred during 1990-2001; 296 of those fires caused 308 injuries and 4 fatalities (Ewhr = 4,012 x 106 hr, In = 0.015, LWD = 36,204). Thirty fires and 26 injuries involved contractors. The greatest number of fires and fire injuries occurred at surface operations; the highest risk rate values were also calculated for surface operations. The number of fires increased during the first four 2-year time periods (1990-1991, 1992-1993, 1994-1995, and 1996-1997), then decreased during the last two periods (1998-1999 and 2000-2001). The number of injuries showed a decrease throughout the periods, accompanied by an increase in employees' working hours. Twenty-five firefighting interventions by mine rescue teams in underground mines and at least 30 interventions at surface operations were required to combat these fires. However, 45 fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. Ninety-seven fires were detected late, and 30 fires were undetected. The ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flame (169 fires or 33% with 137 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (89 fires or 17% with 46 injuries and 3 fatalities), heat source/explosion and flammable liquids/ gas/refueling fuel on hot surfaces (98 fires or 19% with 73 injuries), electrical short/arcing (51 fires or 10% with 16 injuries), and spontaneous combustion/hot material (46 fires or 9% with 17 injuries). The flame cutting/welding spark/slag/flame source caused fires usually involving welders' clothing or oxyfuel/grease and other materials (including chute and dust collector liners, flammable liquids, belt material, crusher, hopper and shaker deck materials, washer plants, equipment mechanical components, stampler breaker, hydraulic fluid, rubber tires and hoses, gear boxes, bin feeder, dump rope cables, screen liner and screen panel, kiln and shaft material, pipelines, liquor pumps, wood pallets, electrical junction boxes, handrails, grease, refuse, shop and wood). The spontaneous combustion/hot material and electrical fires were usually detected late due to lack of combustion gas/smoke detection systems. At least 55 of the 89 mobile equipment hydraulic fluid/fuel fires became large fires (requiring 12 mine rescue team interventions in underground

Jan 1, 2004

By Victor Li, Joley Lam

"INTRODUCTIONJacked piles are piles that are pressed into the ground, usually by hydraulic jacks. For this reason, jacked piles are also known as pressed in piles. Jacked piles are mainly used for the following applications.• Underpinning worksJacked piles have been commonly used for strengthening the foundation of existing structures. In pressing the pile into the ground, the hydraulic jacks will jack against existing pile caps or ground beams that support the structure or against a steel frame connected to the floor slabs or structural walls of the structure. The self weight of the structure provides the reaction force for pile jacking. Jacked piles used for underpinning works usually have lower design ultimate capacities, typically less than 2000 kN (225 tons).• New foundationsJacked piles can be used to support new structures. A heavy pile jacking machine is employed to provide the reaction force for jacking the piles into the ground.• Retaining structuresJacked piles can be installed at close spacings to form a retaining wall. For relatively large and easily accessible sites, the piles can be installed using a conventional pile jacking machine. For sites that are smaller and are more difficult to access, a more compact patented equipment called the Silent-Piler developed by Giken Seisakusho Co. Ltd. in Japan can be used.Jacked piles have several distinct advantages. The vibration and noise induced during pile jacking are minimal. Jacked piles are 100 percent proof-tested to a load level equal to the maximum applied jacking force. The pile jacking machine can also be treated as mobile kentledge for static loading test. In this article, discussion will focus on jacked piles used for supporting new structures.HISTORICAL DEVELOPMENTThe People’s Republic of China (PRC) is perhaps one of the earliest countries in which jacked piles were used as new foundations. Jacked piles had been installed in the PRC since the 1960s. The capacities of jacked piling machines used in the country are usually in the range of 3000 to 6000kN (337 to 675 tons). High capacity jacking machines with a capacity of 9000 kN (1000 tons), presently used by the construction industry in Hong Kong, were also manufactured in the PRC. There are also plans to produce machines with a capacity exceeding 10000 kN (1125 tons). It was projected by Wang (1999) that jacked prestressed spun concrete piles would become one of the most popular pile types in the PRC in the 21st century."

Jan 1, 2004

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By Chris Crowl

Employee involvement does not directly correlate to performance improvement. A key ingredient is the introduction of new Human Resource Systems that promote both performance improvement and employee involvement. Many organizations have tried to use employee involvement as the ''fixer" of performance issues-and seen their performance deteriorate further. They failed to realize that the entire human resource strategy must be connected to the goals of performance improvement and that greater employee involvement is only one tool in that strategy. So what are Human Resource Systems? These are systems that all managers use to get work done. Most of us are familiar with basics such as planning, assigning work, checking progress (auditing), completing assignments. We also commonly think in terms of staffing, training, compensation, or corrective action. All of these are human resource systems. All must be designed to support what you are trying to accomplish with your people. We call that the Human Resource Strategy. Let's examine one part of a total strategy intended to support more employee involvement at Kennecott Utah Copper-the hourly job structure. The design of hourly jobs directly affects how many employees of different capabilities are required to get the work done. It begins to answer some fundamental questions: • What are the roles and accountabilities of each employee? Do they have enough information to make decisions, to take responsibility for their work?

Jan 1, 2004

By K. A. Moxham

The ARM 1100 was described in a paper presented at the 6th International Symposium on Mine Mechanization and Automation in September 2001. It started operation underground at Rowland Shaft in early 2002. This paper covers the results of those trials that resulted in more than 1 100square metres of UG2 being mined.

Jan 1, 2004

By Peter Moser

The average annual consumption of raw minerals in Europe is 10 ton per person. About 50 % is produced by blasting. For a population of 450 million (including the population from the countries of the new member states) this makes 2.25 billion tons of blasted rock, 80 % being building industry aggregates and industrial minerals. In aggregate quarries 10-15 % of the rock blasted can’t be sold, as the material is too fine, i.e. smaller than 4 mm. This ‘fines problem’ is worse in the quarries of limestone and cement producers where up to 30 % of the material is useless. Thus about 450 million tons of useless rock fines are produced and put on waste dumps every year, i.e. 1 ton/person. This problem is addressed by the research project LESS FINES - “Less Fines production in aggregate and industrial minerals industry” which is funded by the European Union under the project contract G1RD-CT-2000-00438. The project consortium, formed of nine partners from 5 EU countries, works on the following two main research subjects: 1. The determination of the natural breakage behavior (NBC) of the rock mass, which is defined as the particle size distribution curve for a certain rock mass with the maximum uniformity and thus for a given maximum particle size that fragmentation curve which gives the minimum amount of unusable fine material. The comparison between the NBC and an actual blast fragmentation curve allows to quantify the fines reduction potential. 2. The adaptation of explosives properties, charging techniques and timing in order to produce only the minimum, inherently unavoidable percentage of fines. With about 15 full time working persons the project is estimated to be one of the largest blast related research activities in Europe at the time of the project period. The project is coordinated by the Department of Mining Engineering& Mineral Economics of the University of Leoben.

Jan 1, 2004

Electronic detonators bring a fundamental and radical change to the potential of rockbreaking operations. The immense technical challenge of safely merging electronic systems with explosives has been largely overcome, but a surprisingly difficult obstacle has been to convert users to the much more capable electronic systems, in routine as opposed to exotic applications. Unit cost is probably the main point of resistance. For years papers have confirmed significant improvements in blasting results, feeding through to enhanced bottom line value for the whole operation: much reduced environmental impact, and improved control over fragmentation, muckpile shape and overbreak. In Africa, a number of operations have been employing the technology for sufficient time to see enduring improvements in throughput, control and cost structure, and these improvements have fed through to the planning process: both the cost and the benefits are part of the plan. This has essentially rendered very unattractive the option of reverting to pyrotechnic systems and incurring the penalties previously unseen but now understood to be avoidable. Examples given are of improved throughput at opencast and underground mines, and greatly extended life at an urban quarry. The general experience of management in implementing the technology is that it over-delivers: adopted to solve one particular problem, significant other issues are also addressed. These extra benefits were quite logical, but not at all obvious prior to implementation. Exploring this reality is essential for harvesting the benefits of the technology sooner rather than later.

Jan 1, 2004

By P. V. Barr, Y. -H. Li, A. P. Watkinson

Subsequent to a campaign of pilot-kiln trials of firing bio-oil and natural gas, scale-up to commercial lime kilns was made using an in-house mathematical kiln model. Both dry limestone and lime mud kilns of 3.5 m OD. by 100 m length were used for bio¬oil firing simulations. Comparisons were made against natural gas firing on the basis of specific firing rate, off-gas volume, energy consumption and overall lime quality. Model simulation results indicate that conversion from natural gas to bio-oil with no productivity loss will increase energy comsumption by about 7.5% and total off-gas volume by about 8%. Alternatively, a 6% decrease in productivity would be expected if off-gas volume is maintained constant. The calculations are sensitive to deviations in the lower heating value (LHV) used in the simulations. A 5% increase in the LHV of the bio-oil, which could result from a 3% decrease in the moisture content, reduces the energy penalty to 2% coupled with a slight reduction in off-gas volume.

Jan 1, 2004

By K. Fujita, T. Kikuchi, Y. Sakamoto

Ceramic fibers were classified as a category 2 carcinogen by The European U legislation. Therefore we developed non-fibrous insulating castable which utilizes n porous aggregate, which is composed of Calciumhexaluminate. Although at beginning we applied alumina cement as binder for non-fibrous insulating castable, kind of formulation had a poor resistance to spalling. We developed non-fibrous insulating castable without alumina cement. This solved a problem which pre\ formulation had a poor resistance of spalling. We applied a new non-fibrous insub castable for reheat furnace in steelworks, then we could achieve good result which condition equivalent to ceramic fiber insulating castable.

Jan 1, 2004

By Santo Ranieri

We will briefly review the nickel market in 2003 and look forward to the supply demand balance for the next few years focusing in on the key factors influencing future price dynamics. On the supply side we will examine slated brownfield and greenfield expansions including the Norilsk factor and the small to mid-range 'supply creep'. We will also review the cost side of the industry and what to expect going forward. On the demand side, we will discuss the stainless steel and non-stainless demand, the China factor and the stainless steel scrap supply cycle. We will conclude by pinpinting where the market is on the current price cycle, and where we believe the mid-term direction is headed.

Jan 1, 2004

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

The scale and seriousness of AustraliaÆs social and environmental problems are no longer in doubt. We are consuming the opportunities of future Australian generations by our lifestyle choices. And at the global level, human activities are altering the very systems on which our species depends. Doing nothing about such problems as climate change is not an option. It is possible to move to a sustainable future but it will require fundamental changes to our values and national social institutions. We must recognise that we share a common future with the entire human family and the other species with which we share the planet. It is not just our humanitarian duty to improve the lot of the poorest people of the world. It is also enlightened self-interest because a world of increasing inequality will be a world of increasingly destructive tension.

Jan 1, 2004

By M. Reza Bateni, M. Zandrahimi, J. A. Szpunar

Titanium aluminides and nickel aluminides offer the potentials, as coating materials, for high temperature and aerospace applications. In this research, attempt has been made to develop Al-Ti and Ni-Al intermetallic compound coatings on the surface of Inconel 738. The coatings applied through pack cementation and simultaneous diffusion annealing processes. Scanning-electron microscopy (SEM), energy-dispersive X-ray spectrometry (EDAX) and grazing angle X-ray diffraction were used for evaluating of coating structure. It was demonstrated that the pack cementation technique could be used to develop TiAl3 and AlNi intermetallic compounds coating on Inconel 738 substrate. When pack cementation technique is based on a halide-activated pack with aluminum and titanium powders, the coating consists of TiAl3 intermetallic compound phase. Whereas, by pack aluminization of Inconel 738, the coating consists of AlNi intermetallic compound phase.

Jan 1, 2004

By I. J. Kotzé, R. T. Jones

Conventional PGM matte smelting requires the presence of a certain quantity of base metal sulphides in order to collect the platinum group metals in a molten sulphidic matte phase in the furnace. Furthermore, the quantity of chromium oxide in the feed materials is controlled in order to avoid the build-up of high-melting chromite spinels in the furnace. Mintek has developed a process for smelting difficult PGM-containing feed materials that contain low amounts of sulphur and/or high amounts of chromium oxide. A DC arc furnace is used to provide the appropriate conditions to generate an iron alloy that collects PGMs very effectively, leaving extremely low residual quantities of PGMs in the slag. Various feed materials have been treated successfully in furnace campaigns running at power levels up to 1.5 MW. The longest of these campaigns was run continuously for more than four months, treating more than two thousand tons of materials such as low-grade concentrates, revert tailings, and converter slag. The campaigns demonstrated the robustness and versatility of the process, and proved that it is possible to sustainably produce a PGM-containing alloy and discardable slags containing an average of less than 1.4 g/t of PGMs over the entire campaign. Keywords: DC arc, smelting, furnace, platinum, PGM, revert tailings, converter slag, ConRoast

Jan 1, 2004