Search Documents

By Bailey S, Avraamides J, Jayasekera S

The anodic dissolution of iron from three different Western Australian reduced ilmenites was investigated using the carbon paste electrode technique. A characteristic current-potential diagram, called a cyclic voltammogram (CV), was obtained for each of the reduced ilmenites. The shape of the CV measured for all three reduced ilmenites was strongly time dependent. The effect of electrolyte composition and temperature on the CV of one reduced ilmenite was also investigated. The results suggest that the initial surface of iron in reduced ilmenite is slow to dissolve and that chloride ions and higher temperatures accelerate the dissolution of this initial surface layer. However, after removal of this layer, the dissolution rate was essentially independent of the electrolyte composition and the temperature.

Jan 1, 1996

The National Mining Hall of Fame and Museum will hold its Ninth Annual Induction Banquet Sept. 8, 1996, at the Las Vegas Hilton Hotel. Six mining greats, two of them living, will be enshrined at the event. They will join 126 other mining legends previously honored by the hall of fame. The keynote speaker will be William Perry Pendley, president and chief legal officer of Mountain States Legal Foundation in Denver, CO. Jeffrey Zelms, president and chief executive officer of The Doe Run Co., will be master of ceremonies. Richard Swayne, regional director USA for Boart Longyear Co. of Salt Lake City, UT, will introduce the speakers. Thomas Falkie, president of Berwind Natural Resources Corp. and chairman of the Mining Hall of Fame’s board of governors, will enshrine the inductees.

Jan 1, 1996

By Jan W. Oberholzer, Patrick Linzer

The globally increasing environmental awareness which has manifested itself in the past few years also encompasses problems associated with mine closures. A crucial requirement for the effective planning, management, monitoring and control of mine closures is an information system which allows the qualitative and quantitative evaluation of proposed closure strategies, not only in terms of their local influences, but also of their potential effects on areas farther a field. This paper describes some of the closure associated problems and the establishment of such an information system from existing facilities, all of which are readily available. No modifications to these facilities are necessary, which enables rapid and cost-effective implementation of the system.

Jan 1, 1996

By M. L. Nave, R. E. Melley

DC motor drives are available technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of DC drive features. The purpose of this paper is to familiarize and inform possible mining users of DC drive attributes.

Jan 1, 1996

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

The new generation Hlsmelt« Direct Iron Ore Smelting Process is a CRA Limited technology initiative. The process development is now focussed on commercialisation. The goal is to have the first commercial vessel operating around the year 2000. The HIsmelt« Process, based on the abundantly available iron ore fines and the more readily available non-coking coals, has the potential to fundamentally change iron ore processing through the application of high intensity techniques to replace the current sinter/coke ovens/blast furnace .technologies. The process will have great potential in the rapidly growing economies of Asia where steelmaking aspirations are based around local market focussed plants. This potential can be. realised as a supplier of premium grade iron units to electric arc furnace (EAF) steelmaking plants or as the front end to an ore based steel mill.

Jan 1, 1996

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yuji Wada, Yukio Katoh, Yoshikazu Hirosaki

In our previous work, the results of photographic observation using a high speed framing camera showed that the difference between precursor air shock wave velocity and detonation velocity was primary factor for the channel effect. It is assumed that the decreasing precursor air shock wave velocity can prevent the channel effect in charge hole.

Jan 1, 1996

By J. C. Harrison

When Exploraciones Eldorado, S.A. de C.V. finished their first phase of reverse circulation drilling at their La Trinidad property in Sinaloa, Mexico they began immediately with permitting and engineering activities. The first phase of drilling lasted four months and ended in April, 1994. The second phase of drilling ran from May through September of 1994. From May through December, 1994, Exploraciones Eldorado performed the permitting and engineering work for their La Trinidad heap leach mine. The mining permit was submitted to the regulatory agencies in February of 1995 and the first draft of the feasibility study finished one month later. The report outlines the permitting and engineering activities that took place during the second half of 1994.

Jan 1, 1996

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

Slide presentation at conference

Jan 1, 1996

By N. B. Gray, A. E. Guerra, D. E. Morton

"The formation of splash in pyrometallurgical operations that involve the injection of gases into a liquid has been the subject of a number of studies over the last few decades. Given the complexity of the phenomena, there have been some advances in understanding the microscale formation of splash but the ability to accurately predict the amount and character of the splash formed is still in its infancy. First, the macroscale mechanisms for splash formation is very varied. Second, the timescales for splash formation are very small, usually less than 100 milliseconds, making experiments elucidating the formation of splash difficult and costly. Work at the GKW CRC has shown that the microscale mechanism of splash formation is primarily is due to the Kelvin-Helmholtz instability. Substantial progress has been made in understanding the behaviour of large bubbles in effecting splash formation and a simple model has been developed to estimate the behaviour of splash formed from a top submerged lance. Direct numerical computation of splash formation using the GKMAC codes developed at the Centre has been successful in simulating the impact of liquid drops onto a liquid bath.IntroductionInjection of gases into melts is used in the metallurgical industry to promote mixing to ensure acceptable heat and mass transfer rates, conveying solids for alloying, provide efficient contact for gas-melt reactions, and as a reactant. High gas injection rates bring about the formation of splash and slop. Extensive splash formation leads to loss of valuable product, creation of safety hazards, formation of accretion on refractory lining and exhaust ducts, and increased load on dust removal equipment. Many operators and researchers have claimed that splash formation is the limiting factor in many gas injected processes. The problems listed above lead to loss of production and increased maintenance, adding to the cost of processing base metals. Over the last five years, the GKW CRC has been studying the formation of splash from a number of sources. They include the impingment of drops on liquids[ l·2.31, slopping of bath liquidI4.51, breakup of gas bubbles at the liquid-gas interfacel61, shearing of liquids by gases[7·81, and impact of packets of fluids on solidsl81. Theoretically, the extreme deformation of fluid shape and the influence of surface tension makes the simulation of flow resulting from only a drop impacting on a liquid surface a very challenging computational fluid dynamics problem. Recently, we have been successful in simulating the formation of the Rayleigh jet resulting from a drop impact showing the effect of drop Froude number on the shape of the Rayleigh jet."

Jan 1, 1996

By Chris M. Haberfield

The design of side resistance of drilled shafts socketed into rock has traditionally been empirically based on the results of pile loading tests in which the side resistance can be isolated from the side resistance. In practice, this is achieved in one of several ways : loading the pile in tension, using a collapsible base, or by using a device such as an Osterberg cell to load the pile from the base. Although this approach has resulted in generally safe design practice, this has been at the expense of efficient design practice. Safety in design has been achieved through conservatism, which has been necessary because of the large scatter that is evident in the pile socket resistance database (Rowe and Armitage, 1984; Kulhawy and Phoon, 1993). Research at Monash University through the 1980's has been aimed towards understanding and then modelling the complex mechanisms of shear transfer at the concrete-socket interface of sedimentary rocks. Armed with such an understanding, the important factors which affect the strength of pile sockets can be isolated, and the reasons for the large scatter can be deduced. This paper briefly describes the research approach taken, and the main features of the design method and computer program which have now been developed. Some load-settlement predictions of the program are compared with the results of full-scale pile socket tests. The paper then presents the results of a numerical study which relates predicted socket a factors to unconfined compressive strength of the rock, socket diameter, initial normal stress and socket roughness.

Jan 1, 1996

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

Physical and chemical methods were investigated to tower thorium levels in Eneabba Ilmenite from the natural levels of 180-500 ppm to give Becher Process synthetic rutile with less than 100 ppm thorium. Chemlcal treatments, but not physical separations were successful. A pilot plant trial of a sodium hydroxide leach (25M NaOH at 75°C and 40 wt% solids for Ih) followed by a sulphuric acid leach (3M H2S04 at 90°C and 60 wt% solids for 211) confirmed that thorium could be removed to below 100 ppm. However, the activity of the ilmenite was not lowered to the same extent

Jan 1, 1996

By G. Laird, N. B. Gray, N. Lawson

"Photographic, video, laser, hot film and conductivity methods are used in the experimental study of gas-liquid flows. A discussion of their capabilities and limitations are given in this paper illustrating the wide range of phenomena that can be studied. Most of these methods are limited to physical models at room temperature with transparent fluids, although they can be extended for use with opaque and hot fluids. A number of these techniques have been used by the GKW CRC in studies on industrial plants and their usage is increasing although a number of technical difficulties still need to be overcome. An in-depth discussion of the laser doppler anemometry (LDA) and particle image velocimetry (PIV) methods is given with experimental results on the flow field of an air plume in water based on advanced development of the techniques and studies carried out at the GKW CRC. The LDA method provides high resolution data on the velocity profiles, while the PIV method provides an overall view of the complex flow structure occurring at the gas-liquid regions. These two methods complement each other in providing experimental data for validating numerical models and exploring the complexities of multi phase flows.IntroductionThe injection of gases into melts is an important operation in the metallurgical industry. It is used in converters, anode furnaces, blast furnaces, ladles, bath smelters, zinc fumers and many other smelting processes. In many of these processes, the gas is injected into a molten bath resulting in the formation of bubbles that promote reaction, mixing, alloying and heat transfer. The study of gas-liquid systems presents enormous challenges to the researcher due to the complexity of the mathematical and physical modelling which require innovative numerical and experimental skills."

Jan 1, 1996

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By Syed M. Tariq, John W. Wilson, Paul N. Worsey

The position of a major joint in relation to a blasthole has a significant effect in presplitting. Broad research into the combined effects of firing two decoupled blastholes has been performed in the past. The effects of joints simulated between two blastholes has also been evaluated. However, no attempt has been made to investigate the splitting effects produced by firing a single decoupled blasthole. This paper presents the results of such an investigation.

Jan 1, 1996

The kinetics of adsorption of gold di-cyanide onto activated carbon has been investigated extensively over the past two decades. These studies have demonstrated that both film and intra-particle mass transfer affect the kinetics. The dominant mechanism of intra-particle mass transfer has not yet been identified. In the work described, surface diffusion and pore diffusion are considered as possible rate-determining mechanisms of intra-particle mass transfer. Mathematical models are described that incorporate film mass transfer and the respective intra-particle mass transfer mechanism with equilibrium described by a Freundlich isotherm. Rate constants of film mass transfer and pore or surface diffusivities were estimated by the fitting of the respective models to experimental carbon adsorption data. The estimated pore diffusivities, after they had been corrected for the porosity and tortuosity of the carbon, were found in most instances to be higher than the molecular diffusivity of dilute gold di-cyanide in aqueous solution. This situation is not physically viable. The surface diffusion mechanism acting in parallel with the pore-diffusion mechanism is thus responsible for the intra-particle transportation of most of the gold.

Jan 1, 1996

By J. Cassells, N. Chrisman, R. Arnold, P. Rusin, L. Quintana

Toxic substances in On solutions can retard biological leaching of sulfide dump ores. On solutions were ana1yzed for metals, organics and chloride and showed inhibitory concentrations of aluminum, manganese and chloride. Inhibition of bacterial activity by the solid fraction of On solution with and without the organic constituents, was evaluated. Bacterial toxicity was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50% to 60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different solvent extraction (SX) reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost-effective and the least toxic.

Jan 1, 1996