Search Documents

By Frank E. McCall, Michael A. Trevits, Fred Garcia

The U.S. Bureau of Mines investigated the influence of atmospheric pressure changes on methane gas migration through mine seals at a mine site located in the Pittsburgh Coalbed. The mine gained access to a coal reserve through part of an abandoned mine and constructed nine seals to isolate the extensive old workings from the active mine area. Underground problems were experienced when atmospheric pressure fell, causing methane gas to migrate around the seals and into the active workings. During mining operations, methane gas levels exceeded legal limits and coal production was halted until the ventilation system could be improved. When mining resumed with increased air flow, methane gas concentrations occasionally exceeded the legal limits and production had to be halted until the methane level fell within the mandated limit. To assist the ventilation system, a pressure relief borehole located in the abandoned workings near the mine seals was proposed. Preliminary estimates by a gob gas simulator (computer model) suggested that a 0.76 m (2.5 ft) diameter pressure relief borehole with an exhaust fan would be necessary to remove enough methane from the abandoned area so that the ventilation system could dilute the gas in the active workings. However, by monitoring methane gas emissions and seal pressure, during periods of low atmospheric pressure, the amount of methane gas that migrated into the active mine workings was calculated. Researchers then determined that a relief borehole, 20.3 cm (8-in) with an exhaust fan could remove at least twice the maximum measured volume of migrating methane gas. Because gas concentrations in the abandoned workings could potentially reach explosive limits, it was proposed that the mine eliminate the exhaust fan. Installation of the recommended borehole and enlarging two other ventilation boreholes located in the abandoned area reduced methane gas leakage through the seals by at least 63%.

Jan 1, 1995

By G. Chi, M. C. Fuerstenau, R. C. Bradt

Reduction of the total energy expenditure in mining and ore preparation processes was achieved by redistribution of the energy from the crushing and grinding steps to the blasting operation. Reducing the burden/spacing distance by 25% or increasing the charge length by 25% during blasting results in significant energy savings in subsequent comminution processes. The energy cost of mining and comminution is reduced by up to 10%.

Jan 1, 1995

By C. G. Treworgy

Geologists at the Illinois State Geological Survey are evaluating geologic and land use conditions that affect the minability of coal to determine how much coal is available for development using current technology and mining practices. Coal resources are being evaluated for selected 7.5-minute quadrangle study areas. In a central Illinois study area, more than 25% of the deep-minable resources were limited from development by unstable roof conditions resulting from thick unconsolidated sediments overlying thin bedrock overburden. In some southern and southeastern Illinois study areas, geologic conditions associated with a paleo-channel limit the minability of significant resources of low-to medium-sulfur coal. Some features which were thought to limit mining, such as areas of closely-spaced oil wells, have been found to have minimal impact on the amount of coal recovered.

Jan 1, 1995

By Ken G. Stowe, Stephen L. Chryssoulis, Christian Bendel, Joe Y. Kim, Ewald Niehuis

"TOF-SIMS (Time-of-flight secondary ion mass spectrometry) was used to detect collectors sorbed onto the surface of mineral particles in concentrate and tailings samples from the Brunswick, Matagami and Kidd Creek concentrators. This technique uses ion beams from either Cs or Ga sources to sputter the particle surface, a method which reduces fractionation of the collector molecule during sampling.In the Brunswick Zn circuit, sphalerite particles lost to the scavenger tails had less amyl xanthate and isobutyl xanthate compared to sphalerite recovered to the Zn final concentrate. Xanthates were detected on the surface of sphalerite particles floating to the CuPb final concentrate.At Matagami, significantly more isopropyl xanthate and isobutyl dithiophosphate were detected on sphalerite recovered to the Zn final concentrate, compared to sphalerite lost in the Zn rougher tails.In the Zn circuit of Kidd Creek, sphalerite lost to the tails had on average ten times less xanthate compared to sphalerite recovered into the Zn final concentrate. Xanthate was also detected on the floated pyrite particles. In addition to isobutyl xanthate, amyl xanthate was also detected on the floated sphalerite and pyrite particles.This preliminary investigation has (a) demonstrated the ability of TOF-SIMS to detect individual collectors on particle surfaces from plant samples and (b) shown that TOF- SIMS is an excellent tool, complimentary to TOF-LIMS, in establishing the surface chemistry of minerals as related to mineral processing."

Jan 1, 1995

By A D. Stewart Gillies

Resource rent taxes are taxes which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. Resource Rent Taxes have from time to time been considered for implementation in bothAustralia and New Zealand. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax.   The implications of the current form of additional profits tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of additional profits tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation.   Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional profits tax is both time, and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory.   A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with resource rent taxes. The review includes examples based on the structure of additional profits tax which is levied in Papua New Guinea.

Jan 1, 1995

The structure and tectonic setting has had a strong influence on gold mineralisation at the Porgera gold deposit. Here, the structural controls on the mineralisation at Porgera are discussed and placed in a regional tectonic context. The Porgera gold deposit is related to the emplacement of the Porgera Intrusive Complex. Prior to intrusive emplacement at Porgera, Papua New Guinea was affected by a major fold and thrust episode which occurred in response to arc-continent collision in the Late Miocene. After crustal shortening the region experienced a relaxation of compression which is expressed in the deformation accompanying mineralisation at Porgera. The first stage of mineralisation (stage I) is hosted by extension fractures, and is spatially associated with exposed intrusive stocks. A later episode of mineralisation (stage II) is hosted by the faults and fractures of the Roamane Fault Zone, which was active as a dip-slip normal fault during stage II mineralisation. Therefore a change in the tectonic environment from shortening to extensional tectonics can be seen at Porgera before and during mineralisation. Rapid fault-slip during stage II mineralisation may have aided high-grade gold mineralisation by subjecting hydrothermal fluids to changes in pressure, temperature, fluid-fluid and fluid-rock interaction. Uplift to form the highlands of Papua New Guinea occurred after mineralisation and was largely complete by 4.0 Ma.

Jan 1, 1995

By T. J. Malterer

Peat has unique physical, chemical, and biological properties. These include high porosity and water retention, high absorption and adsorption properties, high buffering capacity, and it is a rich medium for microorganism activity. Peat has traditionally been used for horticultural purposes. However, in recent years, peat is increasingly being used for waste treatment purposes. This paper reviews North American literature on the use of peat for waste treatment applications. The literature indicates promising use of peat in treating municipal and on-site effluent, removal of low concentrations of heavy metals from wastewaters, and adsorption of liquid and gaseous hydrocarbon pollutants.

Jan 1, 1995

By Jon Y. Kaneshiro, Gregory E. Korbin, Stephen J. Navin, Larry J. Stout

Sewage presently being discharged into the Tijuana River Valley pollutes the valley as well as the beaches in the South Bay of San Diego, making the beaches unusable nearly year round. The SBTO will convey flows down a 8.5 m (28 ft.) by 58 m (190 ft.) deep drop shaft, through a 3.35 m (11 ft.) by 5.8 km (3.6 mile) long tunnel, and up a 46 m by 2.7 m (150 ft. by 9 ft.) riser shaft connecting to a 1.5 km (0.95 mile) of seafloor pipeline and 1.2 km (0.76 mile) of diffusers on the ocean floor. The drop shaft will be sunk through 38 m (125 ft.) of saturated sands and gravels and 20 m (65 ft.) into the dense fine sands of the San Diego Formation. The tunnel liner has been designed as a five piece, single pass, gasketed, bolted, reinforced concrete liner designed to withstand an external head of 76 m (250 ft.) of water and internal operating head of up to 27 m (89 ft.) and to accommodate movement at the numerous fault crossings. The tunnel is contemplated to be driven with a state-of-the-art Earth Pressure Balance Machine (EPBM) or slurry shield machine through a wide range of conditions from clay to gravel with boulders.

Jan 1, 1995

By Sadan Kelebek, Gerhard W. Heinrich, Peter F. Wells, Peter J. Whittaker

"Based on plant mineralogical data & circuit modelling, a pilot plant campaign was conducted at Strathcona Mill to identify options for improving the performance and operating flexibility of the copper-nickel separation circuits. Emphasis was given to options for combined treatment of the two feed streams (primary nickel ore rougher concentrate and copper ore circuit concentrate) to obtain more flexibility in the use of existing column flotation capacities. The pilot test results demonstrated that circuits which incorporated preconcentration prior to column flotation gave the best metallurgical results. Maximum column carrying rates were also related to the preconcentration. Predictions that increased circulating loads from the column scavengers would improve copper-nickel separation performance were confirmed.IntroductionThe copper-nickel separation circuits at Falconbridge's Strathcona Mill produce a high grade (>30% Cu) copper concentrate most of which is treated at the Falconbridge Kidd Creek smelter near Timmins. The remaining nickel concentrate which still contains approximately 20% of the feed copper is combined with other lower grade nickel/copper concentrates and shipped to the Falconbridge nickel smelter. The separation is required because of the limited capacity for copper processing in and downstream from the nickel smelter. Since no nickel is recovered at present in the Kidd smelter, the challenge is to minimize the nickel content of the copper concentrate.At present there are two independent separation circuits treating the rougher concentrates from the copper and nickel circuits as shown in Figure I. The minerals treated are mainly chalcopyrite and pentlandite but there is up to 25% of the copper present as cubanite in the copper ore. The circuits were kept separate because the flotation rates and froth characteristics were very different, probably because of the presence of cubanite and the large difference in the concentrate grades feeding the circuits."

Jan 1, 1995

By C. L. Schneider, R. P. King

Size distributions and liberation spectra were measured in samples taken from 10 streams in a taconite milling circuit under normal operating conditions. The size distributions were deter- mined by sieving and the liberation spectra by image analysis using the linear-intercept method with proper stereological correction. The measured data were used to validate a simulation of the milling circuit using MODSIM which included the calculation of both size distributions and liberation spectra. Both the measured data and the simulator showed that liberated magnetite was returned to the mill in the cyclone underflow. The simulation will be used to improve the economic performance of the plant.

Jan 1, 1995

By Changwoo Lee

Under drastically deteriorated situations, diesel equipment was introduced to some of local coal mines, aiming at higher productivity and better safety. To accommodate various diesel equipment in conventionally developed mines, mining system itself had to be modified; much larger trackless haulage ways were excavated. Possible health hazards of diesel not taken into account at the beginning become a serious concern and effective control measures are being searched for. The purpose of this paper is to study the diffusion characteristics of diesel exhaust in local coal mines. One of the parameters affecting dispersion of diesel contaminants is the coefficient of turbulent diffusion. Since CO2 is known to be closely correlated with other contaminants such as CO, NO, NQ, SO2 and RCD, it was chosen as a tracer gas in a series of dispersion experiments. A large diesel passage as well as a conventional track haulage way were the sites for the experiments. Rectangular dispersion pulses were generated for 30 ~60 seconds and CO2 concentrations were recorded at several locations 50~190 m downwind. The diffusion coefficients calculated graphically vary between 0.10~0.48 m2/s at both haulage ways. The results are analyzed to find any correlation with the air velocity and the distance from the disperser. Skobunov's empirical formula is applied to the experimental data for comparison and the relationship between Reynolds number and Ex/Dp/sci0.4 Sc1…

Jan 1, 1995

By J. L. Watson

n the U.S., lead has been produced via blast furnace processing for over a century, and the slags from that pyro-metallurgical process have been accumulating on industrial sites over that extended period. Lead blast furnace slags typically contain both lead and zinc compounds in an iron-silicate matrix, and it appears highly likely that such materials will have to be processed in the near future to meet with EPA regulations. Thus it is appropriate to investigate possible processing routes to render the slags non-hazardous and simultaneously to recover metal values to partially off-set the inherent high cost of processing such materials. There are two major processing alternatives: one being pyrometallurgical and the other hydrometallurgical. The research reported here investigates leaching/solution purification/recovery processes for lead and presents experimental data for the treatment of lead blast furnace slags from S.E. Missouri. The results of the research suggest that both lead and zinc can be removed effectively from the slag, and that metallic lead can be recovered directly from the organic extractant utilized for solution purification.

Jan 1, 1995

The current understanding of the mechanics of rock fracturing during smooth blasting is largely empirical and qualitative due to an inability to model the dynamic process at the fundamental level. In order to overcome this difficulty, a numerical simulation of smooth blasting is performed using the Dynamic Lattice Network Model. This model is capable of simulating material inhomogeneities and the dynamic evolution of fragmentation at the micromechanical level. In this study, smooth blasting techniques are numerically analyzed to characterize the development of the damage rock zone during explosive fracturing.

Jan 1, 1995

By Fuller T

This paper introduces the technology used in laser surveying systems, and the development of a reflectorless one-man total station. These systems are being used for applications such as blast pattern surveys, face profiling, muckpile surveys and the general survey of inaccessible areas. Black Diamond Solutions is continuing to assess new technology and develop integrated systems for applications in the mining industry.

Jan 1, 1995

By J. R. Koehler

Effective barrier pillar design is essential for safe and productive underground coal mining. This U.S. Bureau of Mines report presents an overview of available barrier pillar design methodologies that incorporate sound engineering principles while remaining practical for everyday usage. Nomographs and examples are presented to assist in the determination of proper barrier pillar sizing. Additionally, performance evaluation techniques and criteria are included to assist in determining the effectiveness of selected barrier pillar configurations.

Jan 1, 1995

"Line Creek Resources Ltd. produces three million clean tonnes per year of metallurgical and thermal coals for the international market. The mining operation, which is located in the mountains of southeastern British Columbia, produces coal from four pits by conventional truck and shovel methods.The South Pit, which has been in operation since J982, has a benched highwall 490 m in height. Shallow dipping coal seams at the base of the syncline formation will be exposed in the highwall over the next four years of pit life. The first of these seams, which will measure 500 m in final highwall length, was exposed in J994. An auger, powered by a 1250 hp engine capable of cutting 2.2 m diameter holes, was brought on site in J994 and has proven to be a successful means of recovering coal from the J3 m thick seam.This paper covers the background to the selection of an auger mining method to recover highwall reserves together with the geotechnical and methane considerations for this approach.IntroductionLine Creek Resources Ltd., a wholly owned subsidiary of Manalta Coal Ltd., owns and operates the Line Creek mine. The operation which consists of four active pits, a processing plant, and rail loadout is located in the southeastern coal fields of British Columbia. Figure 1 shows the general area.The coal bearing sequence at the mine is preserved on the east and west limbs of a major syncline. Up to twelve mineable coal seams, ranging in thickness from 2 m to 15 m are contained in the formation. Within the pits the seams are stratigraphically consistent and structurally undisturbed, except for small-scale thrust faults that create multiple repeats of the seams."

Jan 1, 1995

By Richard D. Hagni

Reflected light microscopy is routinely applied to the study of ore minerals and textures in polished sections prepared from a wide variety of ore specimens. With the increasing interest in environmental problems, the important role of the reflected light microscope in the precise phase identifications and the determination of the textural relationships between those phases needs to be recognized. Among other environmental applications, the microscope has been applied to the recognition of lead smelter particles from remote collect sites in Missouri and those particles have been compared to dust particles from specific localities at the nearby lead sinter plant and lead blast furnace. Dust from a secondary copper refinery has been studied for its mineralogy. Soils in the vicinity of a Missouri lead smelter have been studied for their mineralogy in preparation to the clean up of those soils. Electric arc furnace (EAF) dusts, recently classified as hazardous waste by the EPA, have been examined for their mineralogy and textural intergrowth in order to better evaluate proposed metallurgical treatment procedures to render the dust non-hazardous. The initial products from experimental metallurgical treatment of EAF dusts also have been studied to aid in determining the effectiveness of those treatment procedures. Refractory gold sulfides that have been roasted in the presence of lime to retain environmental objectionable sulfur and arsenic while recovering the gold have been studied by RLM to determine their mineralogy, porosity, and permeability for cyanide leach solutions. These case histories illustrate the applicability of ore microscopy to the study of problems related to environmental concerns.

Jan 1, 1995

By M Ash, P Bellairs

The world class iron ore mines at Mt Whaleback, Tom Price and Paraburdoo located in the Hamersley Province of Western Australia must mine the Mt McRae Shale to obtain high grade ore from the Dales Gorge Member of the Brockman Iron Formation. The Mt McRae Shale contains a Black Pyritic Shale lithology that reacts with Ammonium Nitrate based explosives. This paper provides an overview of the problems associated with mining this reactive rock type as well as the development of a comprehensive procedure to safely and efficiently blast, excavate and dispose of this material.

Jan 1, 1995

By A. Fyson, M. P. Smith, Margarete Kalin

"Drums containing 0.07 m3 of pyritic waste rock from a zinc/copper mine, with and without Natural Phosphate Rock (NPR) additions (40 kg/t waste rock) were set up outdoors. The effluent chemistry has been monitored over a period of 709 days. In the presence of NPR, the cumulative acidity discharged from 7 out of 8 drums was 80 % less than that discharged from drums without NPR. Mixing NPR throughout the drums was more effective in reducing acidity than placement of the NPR in a layer in the drum. NPR treatment was more effective for 'fresh' waste rock than for material which had weathered for more than 4 years. It is concluded that application of NPR to pyritic waste rock could greatly reduce acidity generated.IntroductionWaste rock dumps are significant sources of acid, generated by the oxidation of sulphides. Oxygen and water supply are oxidation rate-controlling factors, and oxygen supply is the reaction-limiting component. If secondary minerals can be formed on the surface of the rocks, pyrite oxidation and therefore acid generation may be reduced or inhibited. Neutralizing agents such as limestone do not prevent the oxidation of pyrite but treat the resultant acid mine drainage (AMD) or acid rock drainage (ARD).Meek et al. (1991) determined in pilot scale experiments that apatite mixed with tailings was more cost effective than liming or use of PVC liners to reduce oxygen and water penetration into the tailings. Phosphate is not acting as a neutralising agent but it creates a chemical condition on pyritic surfaces which prevents reactions of the oxidising agents. Precipitation of principally iron phosphates physically isolates the pyrite surfaces from further oxidation (Ziemkiewicz 1990; Evangelou 1994). The chemistry of the phosphate effects has been described by Spotts and Dollhopf (1990). Secondary mineral formation was evident in the leach pile at Gibraltar when leaching was impaired (Scott, 1991) indicating a link between oxidation and the mineral-formation process. This paper reports on effluent characteristics when waste rock is generating acid in the presence of NPR."

Jan 1, 1995

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995