Search Documents

By D. K. Sengupta

Increased recycling of waste paper has been emphasized in recent years in both the USA and Canada for environmental and economic reasons. Removal of ink particles from the waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. Our study investigated the feasibility of a simplified flotation scheme which showed that about 90-92% ink removal can be achieved while 95-97% ink removal is achievable if a hydrophobic polymer is used ahead of flotation. The clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH, and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1993

Segregation of granular material is a very common phenomenon. Realised in a forced manner it is a basis of all separation processes in mineral processing, mainly classification and beneficiation. Spontaneous segregation, occurring under dynamic conditions and making possible mutual translocations of grains, is however an undesired phenomenon as a rule. It decreases the degree of blending of the material which in many cases is an important technological feature of the material. It should be noted that the segregation can be treated as the reverse phenomenon to blending. The importance and frequency of spontaneous segregation has caused many rules and technical solutions to be developed aimed at decreasing the possibility of the spontaneous segregation. However, not enough attention has been focused on an quantitative description of the phenomenon of segregation, either to ways of quantitatively evaluating segregation effects or to explanation of the influence of conditions under which the grained material exists on the occurrence of segregation and its degree. The paper presents the following topics: 1. new numerical indicator for evaluation of the segregation degree (and blending) of material contained in an arbitrary determined region is proposed; it is determined relative to the maximum possible degree of segregation of the given material when taking into account its individual properties; values of the indicator can be calculated effectively for an arbitrary material, also for ulticomponent material. 2. there is proposed a way of evaluating the state of segregation (or blending) of material in an arbitrary part of the region mentioned above, based on investigation of the gradient of distribution of the material features; algorithms of analytical procedures and calculations are presented for typical cases met in mineral processing; 3. results of initial experimental studies, both laboratory and industrial, concerning the effect of the chosen factors occurring in transport and storage of the material on its degree of segregation are presented; and 4. conclusions referring to the fundamental and practical significance of the results are also presented.

Jan 1, 1993

By E. J. Donovan, O&apos

The use of Dynamic Analysis techniques in the design of conveyor systems is extremely limited. The most frequent use of the technique is in large and expensive systems where the emphasis is on insurance against failure caused by catastrophic tension waves. This paper sets out to illustrate a much wider range of applications where dynamic analysis has been successfully employed. The examples chosen deal with identification and correction of dynamic low tension problems, the variability in take-up movement as other system parameters change, the requirement for proper tuning of starting controls and finally the absolute necessity for a complete understanding of the entire system when specifying brakes for critical applications. The intent of the paper is to get designers to view a conveyor as a system of interacting flexible components rather than as a single rigid body.

Jan 1, 1993

By J. F. Childs

Montana consists of an Archean crystalline basement overlain by Proterozoic through Cenozoic sedimentary rocks. Igneous rocks range in age from Archean to Pleistocene; the most voluminous magmatism and volcanism occurred during the Late Cretaceous and early Tertiary. The state can be divided into three tectonic provinces whose deformational styles are a function of different bedrock responses to Late Cretaceous-early Eocene compressional tectonism. Several long-lived structural zones have been periodically reactivated since the Precambrian, and were the sites of recurrent magmatism. Regional gold distributions are strongly influenced by the tectonic provinces and structural zones. Lode gold systems in Montana occur in diverse geologic settings resulting from a complex interaction between structure, magmatism, and sedimentary depositional processes. Reserves or resources are known for 19 significant lode gold systems, and additional unannounced discoveries have been made recently. Mineralization ranges in age from Archean to Tertiary. The influence of long-lived structures is apparent at both the regional and deposit scale, and in some cases multiple mineralizing events have been superimposed upon one another. Most Montana gold systems have a direct spatial and genetic association with Late Cretaceous through Oligocene igneous rocks. However, the importance of sedimentary rocks and associated depositional processes should not be underestimated.

Jan 1, 1993

By G. S. Hanumanth

Sedimentation of particles during the liquid metal processing of particulate metal-matrix composites can affect the homogeneity, and thereby the properties, of the cast product. A novel electrical probe has been developed to measure the in-situ volume fraction of ceramic particles in molten metal baths. Using this probe, sedimentation rates for 90 pm silicon carbide particles dispersed in molten aluminum A356 alloy were measured over a wide range of particle volume fraction, 0.05 to 0.3. The sedimentation rate was found to depend strongly on particle volume fraction; the time to clarify a 0.15 m depth increased from approximately 60 to 500 seconds as the volume fraction increased from 0.05 to 0.3. Measured sedimentation rates agree well with the predictions of a sedimentation model based on one-dimensional, two-phase flow theory in which the inter-phase drag function is derived from the momentum equation, utilizing the Richardson-Zaki Equation for sedimentation in aqueous systems. The implications for solidification are discussed.

Jan 1, 1993

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993

By M. D. Attfield

During 1992 a number of papers were published on aspects of respiratory disease in US underground coal miners. These included reports on trends in prevalence of coal workers' pneumoconiosis, the risks of developing coal workers' pneumoconiosis in relation to dust exposure, and the relationship between lung disease other than pneumoconiosis and dust exposure. The intent of this paper is to provide a summary of the essential findings from these investigations. PREVALENCE AND INCIDENCE OF COAL WORKERS' PNEUMOCONIOSIS Coal workers' pneumoconiosis (CWP) is usually detected in living miners through use of the chest x-ray. Deposits of dust in the lung, and the fibrotic tissue reactions to the dust, are manifested on the x-ray as small and large opacities. These abnormalities are quantified into degrees of severity using a standardized classification scheme (the International Classification of Radiographs of the Pneumoconioses of the International Labour Office). For small opacities, the scheme provides for a four-point scale of abnormality (0, 1, 2, 3), reflecting increasing profusion of the opacities on the x-ray. In this report, category 1 or greater small rounded opacities (CWP 1+) represents the earlier radiographic stages of pneumoconiosis. Large opacities, indicate the later and often disabling stage of pneumoconiosis, usually referred to as progressive massive fibrosis (PMF). Information collected in a national surveillance program for underground coal miners (the Coalworkers' X-ray Surveillance Program (CWXSP)) and a large epidemiologic study (National Study of Coalworkers' Pneumoconiosis (NSCWP)) provide a means to assess trends in CWP prevalence over the years following the reduction in dust levels mandated by the 1969 Federal Coal Mine Health and Safety Act (FCMHSA). These programs are operated by the National Institute for Occupational Safety and Health (NIOSH), and are described in detail in Attfield and Althouse (1992) and Attfield and Castellan (1992). Both studies were divided administratively into distinct time periods, and the results shown here reflect that division. Figure 1 shows the prevalence of CWP 1+ as determined from data from the CWXSP, plotted by time period and years in mining. There is evidence of a temporal reduction in prevalence. (The lack of an obvious decline in the early 1970s may be an artifact arising from use of different versions of the standard classification.) Figure 2 provides information in the same format for PMF, and shows a similar trend [ ]

Jan 1, 1993

By N. D. Jagger

In order to maximize the benefits obtained from flocculating agents when used as settling aids in high rate and conventional thickeners, it is often necessary to dilute the thickener feed prior to flocculant addition. In some cases, no flocculation at all is possible unless dilution water is used. The most common method of diluting thickener feed has been to recirculate some of the thickener overflow by means of a centrifugal pumping system. This represents a significant capital and operating cost. Supaflo Technologies of Australia has developed and patented an internal recirculation method known as Auto Dilution (or "Autodil") which is based on the principle that an hydraulic head differential exists between the inside and outside of the feedwell because of the higher S. G. of the pulp inside the feedwell, By installing non-return ports in the feedwell wall at the appropriate level, supernatant solution flows into the feedwell at a calculated rate and dilutes the feed without any need for external recirculation of overflow.

Jan 1, 1993

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

Minerals are of course important to our way of living and hence the search and exploitation of minerals has always had a high priority in Australia. Metal mining commenced in South Australian in the 1840s when silver-lead and copper were first mined. This was Australia's earliest mining era and led to the rush that never ended. This and subsequent mining periods have had significant, widespread impact on local and national economic development, settlement, and social conditions.

Jan 1, 1993

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

By Tevfik Güyagüler

Airborne dust is one of the important environmental problems in mines. Besides conventional dust control methods, recently, extensive studies have been carried out on the elimination of dust before it has actually been formed. Determining to what extend rock characteristics influence the amount of dust produced during different mining activities are considered as a guide for this purpose. The factors analyzed in this study were main mechanical, physical properties and petrographical constituents, namely free and combined silica. In the study regression analysis techniques were applied to investigate the effectiveness of aforementioned factors. INTRODUCTION Nearly every aspect of mining activity contributes to the air pollution caused by dust. Therefore the harmfull effect of airborne dust has been investigated many years and limit dust concentration levels were determined for various types of mine dust. To keep the dust level below limit value different dust control techniques have been applied in mines. So far, the well known techniques regarding dust control focuses on reducing the amount of airborne dust. However, recently various studies have been carried out to avoid the dust before it has actually been formed (Bhaskar and Gong, 1991). In this respect, influence of rock characteristics on dust formation is regarded as a guide for this purpose. The present contribution describes such a study in which the drilling operation is considered as the source of the dust. In this study drilling and dust sampling process were undertaken in a model gallery that simulates an underground working. The mechanical and physical properties of the rock samples were measured in rock mechanics and ore dressing laboratories. Quartz and combined silica contents of the rock samples, on the other hand, were determined in the laboratories of geological engineenring department. Rock samples used in the research were different types of coal measure rocks, namely, sandstone, shale and conglomerate. The rock characteristics studied in this work are brittleness, toughness, rock strength, hardness and hardgrove index as inherent properties; free silica, and total silica contents of rock samples as petrographical constituents. Although there have been various studies to determine the effect of rock characteristics on the dust formation, still the type and extend of effectiveness have not been understood clearly. LITERATURE REVIEW Most of the studies investigating the effect of rock properties on dust formation concluded that they are effective. In such an investigation, it has been found that inherent rock properties influence dust formation (Das, 1973). In the another study, dustiness of the air was considered as a function of the composition, hardness and moisture content (Panov, 1967). It was also accepted that in a drilling operation more fine dust is produced if the rock to be drilled is hard (Skochinsky and Kamarov, 1969). In some other investigations dust production were considered as a function of hardgrove index (Moore and Bise, 1984) or formulated in terms of brittleness, toughness and hardness (Güyagüler, 1991). The effect of the petrographical properties of coal or rock on dust formation characteristics have also been studied (Baafi, 1979) (Panov, 1967). Because of its importance, various researches were conducted the study to find out the effect of free and combined silica content of dust on dust formation. In one of the study, the relationship between quartz in the coal seam and quartz in the airborne coal dust was investigated (Ramani et al, 1988).

Jan 1, 1993

By Robert A. Jankowski

The U.S. Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the mining industry, has identified and demonstrated the effectiveness of several improved face ventilation techniques for longwall mining systems. These include the following: identifying improved techniques for measuring face ventilation parameters on longwall sections, installing curtains at the intake end of the longwall face to maximize usage of the primary airflow, identifying optimum face airflow rates for maximizing dilution effects, and coursing the primary face intake from tailgate to headgate to minimize outby airflow contamination. Application of these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 1993

By G. Van Weert

The pellet reactor was developed approximately 20 years ago in the Netherlands for softening drinking water. Since then, some 35 plants have been built, ranging in capacity up to 8500 m3/h. Applications now also include removal of phosphates and fluorides and the production of metal carbonates and sulphides from waste streams. The pellet reactor consists of a fluidized bed, wherein the process solution is thoroughly mixed with the precipitation reagent at special inlet nozzles to give over-saturation of the compound to be precipitated. In water softening applications, the compound is CaCO,. In the case of nickel or other metal waste streams, Na2CO3 solution is added in sufficient amounts to precipitate metal (hydroxy) carbonate on the fluid bed particles. These grow typically to dense spheroids, which are removed when they reach 0.8 to 1.0 mm diameter. These spheroids are easily dewatered, free flowing and low dusting. The latter property is becoming an attractive advantage in connection with new plant hygiene regulations. The operation of a 60 cm diameter pellet reactor on nickel containing plating waste is described and the properties of the produced nickel carbonate spheroids are discussed.

Jan 1, 1993

By Slavoljub Makslmovic

One important element of the U.S. Bureau of Mines computer-assisted mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include use of natural gamma radiation (NGR), vibration, passive infrared, video, and radar. To help establish which CID sensor technologies need to be developed for a given seam, the Bureau has collected geological and mining practices data from over 460 underground and surface mines in the United States. Also, over 500 coal and rock samples have been obtained for laboratory analyses of ash content, sulfur content, heating value, and NGR. The Bureau's findings indicate that the immediate roof strata in 81% of the underground mines and 93% of the surface mines are made up of shale, draw slate, or claystone. The immediate floor strata in 88% of both the underground and surface mines consist of fireclay, shale, draw slate, or claystone. The results of the NGR testing indicate that the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1993

By Yoon R-H, Luttrell GH

A theoretical model has been developed to predict the probability of particle collection by air bubbles in a quiescent flotation pulp. The model considers the effects of both hydrodynamic and surface chemistry forces acting during the bubble-particle interaction. Hydrodynamic forces considered include the gravitational, buoyancy, streamline and film thinning resistance forces. The surface chemistry forces considered include the electrostatic, dispersion and hydrophobic forces. The hydrophobic force has been estimated from extended DLVO theory. The model is capable of predicting hydrodynamic and surface chemistry conditions under which bubble-particle adhesion is possible. Validity of the model has been verified experimentally.

Jan 1, 1993