Search Documents

By J. M. King, C. J. Boggs

Acquisitions of mineral properties and companies can saddle the acquirer with unexpected and substantial liabilities and obligations incurred by the acquired or selling company that are not readily apparent from review of the company's books or files. This paper will address selected areas of concern, such as environmental and reclamation liabilities, problems of foreign ownership by the buyer or seller, pension obligations, plant closing laws, effective title review, land use and zoning.

Jan 1, 1992

By Clark I, Stockton N, Warren L

Nickel flotation circuits currently experience difficulties in recovering fine particles of pentlandite less than ten microns. By agglomerating these particles using shear-flocculation it is hoped to improve the recovery of these fine particles. A sample of massive sulphide ore from the Kambalda region was separated using magnetic separation to obtain a high grade pentlandite concentrate (> 90 per cent). This was finely ground to produce a sample with particles of 50 per cent minus 10 um in size. This sample was then shear-flocculated using a variety of reagents, including xanthates, dithiophosphate and mercaptobenzothiazole (MBT). The effects of reagent type and concentration, conditioning time, impeller speed and type, and pulp density were studied. Froth flotation tests were also conducted on the shear flocculated pulps to compare the effects of xanthate and MBT on the recovery of pentlandite.

Jan 1, 1992

By C. O. Bounds

The magnetic properties of (NdDy)15Fe78B6 sintered magnets have been evaluated using powder prepared by Inert gas atomization. The atomized powder had a particle size distribution from 1 to approximate 1000 microns. The as atomized powders have been sieved into, coarse, intermediate, and fine fractions; magnetic properties were evaluated for the as produced powder and each fraction. A B, of 11.7 kG, a Hci of 11.0 kOe and a BHmax of 32.5 MGOe was -obtained on a sintered magnet made from the as-atomized powder. The magnet made from coarse powder exhibited a slightly higher B, of 12.1 kG, while that from fine powder showed a decrease in B, to 11.2 kG. Hydrogen decrepitation has been utilized to study its effect on the magnetic properties. Finally, cast ingots with a definite columnar structure have also been used to compare the magnetic properties of magnets of the same nominal, composition but of different alloy preparation process. Hydrogen decrepitation does not appear to improve the magnetic properties of magnets made from thin cast ingots. However, it does show a significant improvement in the Hci of magnets made from the atomized powders. Possible causes for the differences in the magnetic properties on magnets made from each process have been discussed in the paper.

Jan 1, 1992

By M. E. Myers

An experimental program is being carried out to determine the thermodynamic characteristics of zinc solubilization in high-temperature iron and iron-carbon alloys. Two versions of an isopiestic technique are being used, with zinc at a lower temperature being equilibrated with pure iron foils or molten iron-carbon alloys at a higher one. The lower temperature sets the partial pressure of zinc vapor, and thus the activity relative to a given reference state. Initial results show Henrian behavior for dilute zinc solutions in austenite and a molten 4.6% C alloy, with unit-pressure solubilities in pure Fe that closely match the predictions of Wriedt.

Jan 1, 1992

By Tim B. Vanderwood

The mineralogy of dusts from several locations in a lead smelting plant, remotely collected dusts and soils near the lead smelter, and dusts from a secondary copper smelter were examined by reflected light microscopy (RLM) to determine their m1neralogy, texture, and origins. Individual grams were further analyzed by microbeam techniques. Detailed petrographic analysis of the dust has been supplemented by automated scanning electron microscopy combined with energy dispersive x-ray spectroscopy (ASEM-EDS). This technique allows the rapid sizing and chemical analysis of thousands of individual particles in a dust sample, producing particle size distributions as well as statistically meaningful breakdown of a sample into chemical types (e.g., proportion of galena vs chalcopyrite).

Jan 1, 1992

Sustainable development places a heavy burden upon everyone involved in the public policy debate, about how to balance economic growth and environmental protection. We must treat that responsibility very seriously indeed. The mining industry especially cannot dodge the responsibility, even if it wished to.

Jan 1, 1992

By Mohamad Hussein

Low strain dynamic tests are performed to evaluate the structural integrity of driven or cast-in-place concrete piles. This type of testing requires minimal pile preparation, and is simply performed by attaching an accelerometer to the pile head and striking the pile head with a hand held hammer. The measured data is processed by a dedicated system, inspected for wave reflections, and interpreted based on one dimensional wave propagation theory. Piles are normally tested shortly after installation so that problems can be identified early and corrective measures taken before construction of the superstructure. However, evaluation of existing foundations is occasionally required. Often, pile installation records are not available rendering impossible any rational foundation reanalysis. This paper discusses three case histories where low strain dynamic measurements allowed determination of pile lengths and structural integrity under existing structures where pile heads were not accessible.

Jan 1, 1992

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By Anylmore M, Walker A, Fletcher A

Roasting of sulphide and sulph-arsenide gold ores produces unwanted emission of sulphur and arsenic oxides, and a less than complete recovery of gold. Pyrite loses sulphur and arsenopyrite loses arsenic at a useful rate at temperatures of 600¦C and above in an inert atmosphere. Sulphur and arsenic driven off can be condensed before entering the atmosphere. During the process, solid-solution gold redistributes itself on internal surfaces of the resulting iron sulphide. Two subsequent processing options may be used; direct cyanidation of the porous sulphide resulting from the anoxic pyrolysis, or a second-stage roast to oxidise the remaining iron sulphide. The first option may be viable under certain conditions of pyrolysis. The two-stage option has an environmental advantage over the traditional roast because it reduces oxide vapour emissions by 50 per cent. The second stage may provide nearly enough energy to sustain the entire process.

Jan 1, 1992

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By R. Hogg

Sedimentation in highly flocculated suspensions of fine particles such as clays occurs through individual settling units (flocs) which have very open structures and correspondingly low density -typically less than 5% solids by volume. It follows that such settling processes rapidly lead to the build-up of a bed of flocs which are essentially close-packed, with inter-floc porosity of perhaps 50%, but with an overall solids content of no more than about 2-3 percent by volume. An important consequence is that the thickening process is dominated by the consolidation of this bed rather than by simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate that for a given system, consolidation rates are essentially determined by solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical as well as chemical conditions of the flocculation process. Furthermore the extent to which gravity consolidation proceeds depends on the total weight of sediment (i.e. on both height and solids concentration). The implications with respect to thickener operation and the requirements for laboratory testing for thickener design are discussed.

Jan 1, 1992

By James F. Allan

"Abstract -The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec . Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by ? 0.10% Y203, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% Zr02. The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and cale-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and rninor britholite. Yttrium also occurs in britholite in cale-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By Louis J. Jansen, D. E. Ranta

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Precambrian greens tone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1992

By John J. McClelland, Gerald T. Homce, John R. Thalimer

The U.S. Bureau of Mines has investigated the early detection of insulation failure in squirrel cage induction motors for the past 4 years. Research was done using a sophisticated empirical data-modeling technique based on values calculated from a motor's voltage and current phasors. This technique produces two polynomial equations that calculate the insulation leakage current and power. These models were implemented in a prototype system that monitors six motors on a continuous miner for insulation leakage. These insulation leakage values are used to anticipate insulation failure. The system consists of a motor-data-system for each motor on the machine and a control computer located away from the miner. Each motor-data-system consists of an analog interface to the motor's voltages and currents, a single-board computer that reads digitized data and calculates voltage and current phasors, and a bus node that interfaces the single-board computer with the rest of the system by way of a serial bus system. Using this bus system, the control computer requests and receives phasor data from the motor-data-systems. From these data the control computer calculates and displays two deterioration values for each motor, for leakage current and power, using Bureau-developed models. These values are stored in a data base from which the user can display graphs of each motor's deterioration values over time.

Jan 1, 1992

The treatment of gold-plant tailings with ferrous sulphate to remove the cyanide is currently in use, on several gold plants. In some cases there is scope for optimization the process. The present work provides a detailed study of the reaction between cyanide and ferrous sulphate. Optimal conditions for the removal of total cyande required a ph of 5,.5 to 6,5 and an Fe:CN molar ratio of 0,5. Ferrocyanide ion is shown to be unstable In aqueous acidic solution, with rapid oxidation to ferricyanide, (Fe(CN) 6 ), and formation .of Fe(CN)5H2O3- at pH values below 4, The precipitate from the reaction between cyanide and ferrous sulphate consists mainly 01 Insoluble Prussian blue, Fe4[Fe(CNI&!.3,and IS shown to be unstable in the presence of alkaline solution, since it decomposes rapidly at pH values above 7 to form ferrocyanide, (Fe(CN)6 ), in solution and various insoluble iron oxides,

Jan 1, 1992

By Linda J. Dahl

The U.S. Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ leach mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits which include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, proximity of ore minerals to the leach fluid paths, surface subsidence potential, and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental, and economic feasibility of in situ leach mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability, and porosity as they relate to in situ leach mining.

Jan 1, 1992

By Strickland R. E J

Heap leaching is establishing itself as an efficient method for the extraction of gold from low grade ore. It has the advantage of low capital costs, low operating costs and rapid startup. However, not all ores are amenable to heap leaching. It is only applicable to well oxidized ores that have reasonable permeability characteristics. Ore with excess fines or clay often display low permeability and are unsuitable for heap leaching.In this study, an attempt has been made to increase the rate of cyanide leach solution percolation by flocculating clay particles or reducing the surface tension of the leach solution. A wetting agent was found to decrease the rate of gold dissolution, possibly by presenting a hydrophobic surface to the gold particle. Flocculation of the clay increased the solution flow rate. The flocculation agent had no affect on the total gold leached but decreased the leaching rate.

Jan 1, 1992

By Cotton R. E, Cox R

Digger Rocks is one of several nickel-bearing sulphide deposits localised within komaLiitic volcanics of the Forrestania Greenstone Bell within the Archaean YiIgam Block of Western Australia. Exploration and evaluation to April 1990 have delineated a resource, at a nominal cut-off grade of 0.5 per cent Ni, of 1.9 Mt at 1.1 per cent Ni within a lensoid sulphide body which strikes NW, dips 50°SW, and occurs at a depth of 30 - 110 m below surface. There has been no production from any of the Forrestania nickel deposits to-date. The deposit, comprising both disseminated and massive sulphides, has maximum dimensions of 400 m strike, 115 m vertically and 90 m true width. Generally the massive sulphides occur at the base of the disseminated sulphides, on or close to the base of the Digger Rocks dunite. The two main massive sulphide lenses have maximum dimensions of 120 m strike, 75 m vertically and 16 m true width (northern lens) and 60 m strike, 25 m vertically and 4 m true width (southern lens). The average grades of the massive and disseminated sulphides are 5.9 per cent i and 1.2 per cent i respectively. The massive sulphides generally have sharp hangingwall and fOOlwall contacts and display strong internal grade anisolropy.The massive sulphides are mainly within the supergene zone and consist of violarite, pyrite and marcasite. The disseminated sulphides are mainly within the primary zone and consist of pentlandite, pyrrholite, pyrite and minor chalcopyrite. Alteration zones, up to six in number, are complex in detail. The sulphides are capped by an average of 30 m of sub-economic, leached, siliceous, oxidised material.A genetic model for the deposit is described which places Digger Rocks in Category 2 (sulphides in large layered dunite bodies) of the latest classification of komatiitic nickel sulphide deposits in the Yilgam Block of Western Australia by Hill and Gole (1990).

Jan 1, 1992

By Kapoor M. L

EMF measurements were performed in the temperature range of 933-1095 K to determine the thermodynamic properties of oxygen dissolution in liquid lead and lead-tin alloys with tin in the dilute concentration range of 0 to 6 atom per cent. The oxygen in the Pb-O system was varied by equilibrating with (PbO) slag, and that in the Pb-O-Sn system was varied with the addition of lead oxide. Wagner's interaction parameter approach was used to evaluate the self interaction parameter and ternary interaction parameters at different temperatures, to yield: E8(pb) = 97.35 - 113.27 x 103/t Eo(pb) = 139 - 20.616 x104/1' Quasichemical formulation was employed to yield Inf to reveal the effect of tin on oxygen in lead. Results have been predicted on the basis of classical models and those obtained using the QCT approach of Alcock and Richardson at Z=2 have been found to agree with the experimental Data.

Jan 1, 1992

A number of factors have resulted in the widespread use of computer simulation as a day to day tool in the mineral processing industry, as is the case in most engineering disciplines. A number of simulation packages, both steady-state and dynamic are now available commercially. The developers of such software face an enormous challenge in maintaining and improving the packages due to the complexity inherent in such systems. This problem known as the software crisis faces all developers of complex software. Object-oriented (OOP) and design is a methodology which has been developed to try and minimise this problem. The use of the OOP paradigm in the devlopment of simulation software for mineral processing systems is explored in this paper and it is found that OOP techniques have major benefits for the design and development of such software.

Jan 1, 1992