Search Documents

By Chris M. Healey

"Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10070 of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are: 1) Line Drilling 2) Cushion Blasting 3 Smooth Wall Blasting 4) Buffer Blasting 5) Presplitting or Preshearing 6) Air Deck Presplitting

Jan 1, 1992

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By LeJuge G. E, McKenzie C. K

Innovative mining and blasting techniques were demanded at the Richmont Mines, Francoeur Mine in Quebec, Canada, by a narrow, shallowly dipping high grade gold ore body. The ore body being mined occurs as a thin tabular deposit varying in thickness between 1.5 and 3.7 metres, and dipping at 36¦. The mine proposed experimenting with open stoping techniques using small diameter drill-holes. The hangingwall required progressive, full face rockbolting after each production blast, utilising a specially manufactured machine which provided access to the hangingwall for both scaling and bolting. Blasted material is mucked from the stope by scraper and hoisted directly to surface without benefit of primary crushing.

Jan 1, 1992

By Kim Lapakko

As part of a project funded by the US EPA, through the Western Governors' Association, the recent literature on the prediction of acid drainage from metal mine wastes was reviewed. Static tests such as Acid Base Accounting, Modified Acid Base Accounting, B. C. Research Initial Test, and APP:S Test attempt to quantify the total capacities for a mine waste to produce and consume acid. In kinetic tests (e.g. humidity cells, soxhlet extraction, elevated temperature oxidation, column tests, batch reactor tests, B. C. Research Confirmation Test) mine waste samples are subjected to oxidation and the resultant drainage pH is assumed to reflect that of mine wastes dissolving in the field. This paper summarizes information presented in the recent literature on static tests.

Jan 1, 1992

By Tyler DB, Thin LGT

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications are made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a new squat pillar empirical strength relationship.

Jan 1, 1992

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

Through 1986, Kentucky was the nation's largest coal producer. Currently it ranks third in production, behind Wyoming and West Virginia. Because of the size and variety of Kentucky's coal industry, virtually every kind of surface coal mining and reclamation activity takes place in the state. Extensive coal deposits occur in two separate areas: the eastern coal field, which is part of the Appalachian coal field, and the western coal field. Kentucky's reserves are estimated at 65 billion tons, with 27 billion tons in eastern Kentucky and 38 billion tons in western Kentucky. Kentucky coal is high in volatile matter, low in sulfur and ash, and relatively high in heating value. Coal from Kentucky's eastern coal fields contains a sulfur content of less than 1 percent. Conditional primacy was granted to Kentucky May 18,1982. Since then, all conditions have been removed; final regulatory approval was granted on May 30,1985. The Abandoned Mine Land Program was approved with the regulatory program May 18, 1982.

Jan 1, 1992

By Harris RW, Wood BR

At any given time, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes In the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

Halide media are considered as suitable alternatives to cyanide for extracting gold and have received much attention lately. The extraction of gold by iodide-iodine mixture has been patented and briefly studied without much attention given to the fundamental aspects of this process. This paper reports recent studies on the kinetics of gold extraction in iodide media, using hypochlorite, iodine and hydrogen peroxide oxidants. The kinetics of dissolution was found to be dependent on the solution pH, reagent concentration and most importantly the iodide- oxidant molar ratio. Without proper control, the gold surface can be passivated due to the formation of solid products. Thermodynamic modelling was carried out to determine the equilibria governing the dissolution process. The formation of AuI solid was also identified as a possible product during the dissolution.

Jan 1, 1992

By Dean S. Rogers, R. A. Metz

The conventional role or exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1992

By D. E. Ranta, Leigh A. Readdy

Defining classes of ore using geostatistical methods that match historical classifications has presented problems in the past. A simplistic and practical approach to this problem is presented. An example of the approach is presented using a porphyry-type system as a case study. The technique described uses area of drill-hole influence and known conditions from similar deposits, or the production history of the deposit being studied. It provides a practical bridging mechanism for defining the class of ore on a block-by-block basis using the error of estimation value developed during kriging. The approach provides a filtering method that refocuses attention on the adequacy of drill-hole spacing.

Jan 1, 1992

By Robert B. Parsons

"The annual onslaught of provincial budgets and tax changes is complete, and once again the Canadian taxpayer is being asked to dig deeper into his pocket to fund old and new programs. It is noteworthy that 1987 tax reform promised lower taxes, but a broader fax base. Five years later, we still have the broader tax base, but the lower faxes have gradually crept up to pre-tax reform levels. Surprise! Surprise!IntroductionThe last edition of Tax Notes commented on some important proposals announced in Manitoba's 1992 budget. In this issue, Tax Notes summarizes the 1992 budget proposals of British Columbia, Ontario and Quebec. These budgets reflect the continuing trend of transferring responsibilities and the related costs-from the federal government to the provinces. As well, the budget papers bear witness to the respective governments' political stripes. British Columbia, Ontario and Quebec are seeking higher tax revenues. Only Quebec continues to acknowledge the importance of the mining industry in its annual budget documents."

Jan 1, 1992

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

8.1 INTRODUCTION Under room and pillar mining if the extraction ratio is low, (i.e., < 50%) a pillar can support the overburden without collapse and there will be no surface subsidence whatsoever. In other words, if the pillar sizes are properly determined to support the overburden weight, the roof strata cannot cave and there will be no surface subsidence, provided the entry width is small and properly reinforced so that a continuous roof fall leading to piping or the total collapse of the roof does not occur. Under the prevailing mining conditions in the US if only development mining is em¬ployed in room and pillar mining (i.e., no pillar extraction), the extraction ratio is usually less than 50% and generally no surface subsidence will occur. If pillar mining is employed, surface subsidence may occur, depending on the extraction ratio and the size of the remnant pillars (or stumps) left in the gob. The higher the extraction ratio, the smaller the stump pillars left behind in the gob. As the size of the stump pillars becomes smaller, the possibility of their support¬ing the roof without collapse is smaller. If all stumps are crushed completely, the roof will collapse and surface subsidence will occur. Again, whether surface subsidence occurs, it depends on whether the remaining stumps can support the overburden or not. Therefore, since the weight of the overburden which the stump pillars have to support is proportional to the mining depth, a fixed¬size stump pillar can support the overburden at a shallow depth, but will collapse under greater depths. In this context extraction ratio is not the only parameter for determining whether surface subsidence will occur. Furthermore, during pillar mining a pillar can be cut away in many ways to finally reach the same extraction ratio. Therefore, the safest way to determine whether or not sur¬face subsidence will occur in room and pillar mining is to compare the strength of all stump pillars in the panel of interest with the weight of the overburden that the pillars have to support. If they are too small to support the overburden, surface subsidence will occur. Under normal mining practices the characteristics of surface subsidence profiles vary with methods of mining. In the US there are two types of coal mining methods, i.e., longwall and room and pillar mining. Longwall mining is indisputably a total extraction method, but different percentages of coal recovery are achieved in room and pillar mining. Recovery is much higher for sections with pillar extraction than those without pillar extraction. For those without pillar extraction, coal recovery increases with increasing entry width or decreasing pillar size. For those with pillar extrac¬tion, the total coal recovery depends on the amount of coal ex¬tracted from each pillar which is in turn dependent on the roof conditions and methods of pillar extraction. Bauer and Hunt (1981) analyzed the characteristics of the subsidence profiles due to the three types of mining methods in Illinois. Fig. 8.1 shows the range of locations associated with the following profile features: profile edge, maximum tensile curvature, maximum slope, maxi¬mum compressive curvature, and maximum subsidence. The scat¬ter of the data increases with decreasing percentages of extraction. The profile is much sharper for longwall mining and becomes milder as percentage of extraction decreases; for longwall mining the profile edge is always beyond the opening, while in room and pillar mining it may fall within. The location of maximum tensile strain moves outward, while that of the maximum compressive strain moves inward as the percentage of extraction decreases and the maximum subsidence decreases with decreasing extraction ra¬tio. The general concepts discussed in this chapter may not apply to the entry development sections between two longwall panels where roof caving in both panels are very severe and overlap each other. Consequently, it must be treated differently. 8.2 CASE STUDIES Kohli et al. (1982) described several case studies on surface subsidence due to room and pillar mining with pillar extraction. In one case, the seam was 6 ft thick and ranged from 650 to 800 ft deep. The panel was 720 ft wide (Fig. 8.2) and was developed with seven entries. Each entry was 18 ft wide and the pillars were driven at 88 ft center-to-center between entries and crosscuts. Dur¬ing retreating, two additional pillars (pillars J and K) were devel¬oped, two blocks ahead of the pillar line, to take the barrier pillar, 160 ft wide, between panel No. I and No. 2. Pillar extraction began by taking a central slice across the whole panel, beginning from pillar 0 through J. After that, each pillar was sliced by 6 wing-slices, 3 on each side, leaving 4 stumps, 2 on each side. One of each pair was triangular shaped approximately 6 ft wide by 26 ft long. The other was trapezoidal, 26 ft long by 16 ft and 10 ft wide at the upper and lower bases, respectively. This resulted in a total extraction ratio of 85% within the panel. Obviously the stump pillars were not large enough to support the overburden and col¬lapsed completely. The final subsidence profiles were rather smooth, just like those under total extraction (Fig. 8.3). The max¬imum subsidence on Lines A and B was about 3 ft for an average mining height of 6 ft, but the locations of the maximum subsidence were skewed toward panel No. 1. Along Line D, the central por¬tion was flat-bottomed, but the maximum subsidence was only 2 ft, mainly because Line D was only two blocks from the right-side edge. Notice in every profile there was heaving of as much as 0.3 ft, beyond the edges above the solid coal. In another case (Fig. 8.4), the seam was 6 ft thick under 650 to 850 ft cover. Three panels, 710, 400, and 350 ft wide, respec¬tively, were extracted side by side. The entries were 18 ft wide and the pillars at 88 ft center-to-center between entries and crosscuts. Pillar extraction was practiced the same way as described previ¬ously. According to the mine maps, there was no barrier pillar left between the adjacent panels. Thus after extraction the three panels formed a common gob of more than 1460 ft wide. This was re¬flected in the development of the subsidence profile along the county road. After Panel No. I was mined, the maximum subsi¬dence of 1.2 ft occurred at Monument No. 1. This was increased to 1.6 ft after the extraction of Panel No. 2 and went to a further 1.8 ft after the extraction of Panel No. 3. The final maximum subsidence of 4.3 ft occurred at Monuments No. 6 through No. 8, while the remaining portion of the county road showed rebound. However it must be noted that the subsidence profiles were rather bumpy and fluctuated, perhaps an indication of the irregular stump pillars that were left and crushed at various time after mining. Moebs (1982) surveyed the subsidence profiles of four room

Jan 1, 1992

By Xu Linsheng

Datong coal Mine suffers from delays and sudden caving of its massive competent conglomerate roof. Detailed geological studies of the nature of pebbles and matrix of the conglomerate and its sparse bedding, joint and fracture structure, gave rise to investigation of water injection to destroy its strength and to control caving. Comparative investigations, including porisity, permeability, compressive strengths and water injection of conglomerate and sandstone led to empirical expressions relating various properties and to guidance for effective injection and caving practice. This new safe roof control practice should be even more improved with further research, including modelling.

Jan 1, 1992

By John H. Walsh

"ForewordThis paper is to be published in two parts in succeeding issues of the CIM Bulletin. In Part I, the problem of global climate change is explored together with a summary of the government&apos;s present policy in this field. Implications for the steel industry are examined as are possible strategic responses. Part II of the paper will present a new possibility - the joint production of iron and liquid fuels useful for transportation purposes. In the joint production case, the objective is to use carbon for more than one purpose in what might be termed a &apos;carbon cascading&apos; technique. ABSTRACTIt is becoming increasingly probable that emissions of carbon dioxide from the fossil fuels will have to be reduced to deal with the threat of global warming. This issue is likely to be resolved one way or the other in the period 1995 to 2000 which does not leave much time to develop responsive options. In the intervening period, the policy of the Government of Canada is to stabilize emissions of greenhouse gases at their 1990 level by 2000, by encouraging greater efficiency in the use of energy. Should further reductions prove necessary, economic instruments would probably be employed but these would not be applied before a comprehensive international agreement is reached.There are three main themes in this paper: it is assumed that measures to control carbon dioxide emissions will in fact be necessary by the tum of the century; that there will be a rising need for liquid fuels to supply the world&apos;s steadily growing fleet of motor vehicles for many years to come, and that the future niche for Canada &apos;s industry in such a carbon-constrained world will be the operation of the energy-intensive industries with efficiency and environmental sensitivity.The steel industry, as a large user of both coal and energy in other forms, would be significantly affected by a need to reduce carbon dioxide emissions. This paper first examines what might be called the conventional responses open to the industry in such a situation and then explores a new possibility for making better use of carbon by the co-production of iron and liquid fuels."

Jan 1, 1992

By R. A. Metz, James W. Clark, William C. Dixon, Kevin L. Wiley, Thomas R. Couzens

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1992

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. &apos;s Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992

By D. E. Ranta, Ora H. Rostad

Ore reserve estimation, from the earliest "quick and dirty" estimates made at the first consideration of a possible project down to periodic revisions of detailed estimates made during the life of a mine, should take into account many geologic and allied factors in order to obtain results that will provide proper guidance for necessary economic decisions. Factors include: sample collection and analysis, character of the vein and associated wall- rock, mineralogy, pre and post mine oxidation effects, core loss, sample correlation, internal vein structure, wallrock controls, geologic factors affecting dilution in mining and interrelated mining and milling problems.

Jan 1, 1992