Search Documents

By Wenqing Qin, Yunfan Wang, Ximei Luo, Fen Jiao

In order to investigate the effect of nanobubbles on adsorption of surfactant on mineral surface, the nanobubbles on the surface of calcite with -37µm fraction in the sodium oleate system were controlled by pressurization and decompression to mixing vessel. Subsequently, the adsorption amount of sodium oleate on the surface of calcite were detected by ultraviolet spectrum at different stirring times and different pressures. At the same time, the nanobubbles on the calcite surface were imaged with atomic force microscopy (AFM). In addition, a homemade vacuum Hallimond tube device was used for the flotation of single mineral, and the grade and recovery of minerals in concentrate was used to determine the influence of the nanobubbles on flotation. The experimental results showed that a large number of nanobubbles were found on the calcite surface by AFM under the dissolved oxygen difference (DOD) condition of -4 mg/L. And a large difference in adsorption capacity of sodium oleate on the surface of calcite was observed under different air pressure conditions. It indicated that the ambient pressure had a certain effect on the adsorption of sodium oleate on the calcite surface, and this effect did not depend on the constant low pressure or constant normal pressure, but depended on the changing process of pressure. The single mineral flotation experiment results indicated the recovery of calcite under decompression condition (formation condition of nanobubbles) was 1.5-2 times that under constant normal pressure, and the flotation time is much shorter. Moreover, the recovery under constant normal pressure was greatly influenced by flotation time. In this paper, only one aspect of the effect of nanobubbles on mineral flotation was preliminarily explored. It was confirmed that after vacuum-pumping, the adsorption of sodium oleate on calcite surface could be increased, the flotation time also was greatly reduced and the recovery of calcite was increased.

Jan 1, 2018

By M. McClintock

"High Pressure Grinding Rolls (HPGR) is increasingly being chosen for comminution circuits for its energy-efficiency for hard rock mining operations. Despite HPGR’s growing popularity, geo-metallurgy programs are still prohibitively expensive because of large sample requirements. Traditionally, sizing HPGR application requires a significant amount of sample, in the order of 1 to 10 tonnes, depending on the level of study and complexity of the resource. Therefore, engineering and design of HPGR circuits typically are reliant on few composites that are required to be representative of the resource and mine plan. Three bench scale HPGR test methodologies were developed in 2015 at NBK Institute of Mining Engineering at the University of British Columbia (UBC) capable of defining the energy size breakage relationship of pilot HPGR. These methodologies were developed to allow bench scale testing for different levels of study from PEA (Preliminary Economic Assessment) to detailed design and operations. The Piston Press test defines the energy size reduction relationship by measuring specific energy consumption and corresponding feed and product size distributions. The advantage of Piston Press testing is the small sample requirement of 5 to 10 kg. Small sample requirements allow multiple samples to be tested across a deposit. Piston Press testing allows extensive geo-metallurgy programs that can determine ore variability and inform in optimization and production planning. To date, the Piston Press methodologies have been validated on a pilot-scale HPGR unit located at UBC. Recently, testing was conducted to calibrate and validate the Piston Press test against full-scale HPGR on a gold sulphide ore deposit. The program included the collection of operational data with the respective HPGR feed and recycle sample. Sample collected was used both for Piston Press testing and HPGR piloting. This paper discusses the test-work and results as carried out during this program, using the aforementioned methodologies."

Jan 1, 2018

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By Det Juridiske Fakultet, Maria Madalena das Neves

The ocean is increasingly seen as the answer for a myriad of challenges facing humankind. In effect, in addition to being vital for transportation and communication, the oceans contain living and non-living resources that are essential to meet the demand for food, and to the development of pharmaceutical products, energy resources, and high-technology products. This entails that the oceans are under pressure by different activities: navigation, fishing, oil and gas exploration and production, renewable energy development, laying of cables and pipelines, marine scientific research, bioprospecting, and deep-sea mining for minerals and metals. The growing demand for essential minerals and metals such as cobalt, nickel, zinc, copper, and manganese, seen in tandem with technological advances in deep-sea mining, makes the latter an increasingly attractive activity, both in areas within and beyond national jurisdiction. At the same time, the further development of deep-sea mining adds to the problem of the competing uses of maritime space and accentuates the need to balance and articulate the interests of the different users of the seas (States, sponsored deep-sea mining investors, oil and gas investors, fishermen, shippers, etc.). Furthermore, as deep-sea mining activities increase and move on to an exploitation phase so does the possibility of new disputes (for instance during deep-sea mining exploitation a communication’s cable is severed, a vessel conducting deep-sea bottom fisheries damages deep-sea mining equipment, etc.).

Jan 1, 2018

By Sergey Dyachenko

"Following the adopted strategy for making the production modern, efficient and environmental friendly the Company completed a stage of the integrated program aimed at reconfiguration of its processing capacity.Upgrade of the Talnakh Concentrator with commissioning of two start-up facilities (SF) allowed an increase of 30% in its ore processing capacity up to 10 mtpa. In addition to a new high-tech equipment installed, a new concentration process was adopted offering the main advantage of 25-30% reduction of sulfides in concentrate. New concentration technology enabled the total amount of produced nickel concentrates (from Norilsk and Talnakh Concentrators) to be processed at upgraded smelting facilities of Nadezhda Metallurgical Plant and allowed decommissioning of smelting capacities of Nickel Plant resulting in emissions reduction by 30%.Nornickel plans to boost the capacity of Talnakh Concentrator to 18 mtpa by 2022, after commissioning of the 3rd SF. This will provide a shorter route for ores transportation from Talnakh mines along with improvement of cost/performance ratio of ore processing through the usage of the modern equipment and optimized concentration flow scheme. Total capacity of Talnakh Concentrator will be sufficient to process ores from Talnakh deposits with planned upstream assets development taken into account. Volume of ore mined from Norilsk deposits to be processed at Norilsk Concentrator will be also increased.Upgrading the crushing section at Kola MMC Concentrator in 2015 provided finer particles of the crushed ore, resulting in 6.6% increase in specific capacity of ore mills as well as 1% higher recovery of non-ferrous metals due to improved liberation of ore minerals.In 2015-2017 the Company was actively engaged in optimization of existing process flow schemes and parameters of Kola MMC, new high-performance reagents were adopted for concentration process, namely, collectors, depressors, flocculants. These measures allowed the Concentrator to reduce its annual operating unit costs and ensure sustainable production of concentrate with the lower grade of the incoming feedstock.Launched in October 2017, Bystrinsky GOK’s Concentrator was 3D designed and received a range of advanced technological solutions.All design process procedures and technologies rolled-out at the Company’s concentrators were developed by Russian R&D institutes, with the key role of Gipronickel Institute, R&D Service of Kola MMC and Polar Division's in-house Engineering Support Centre."

Jan 1, 2018

By Lebeau M., P. Duguay

"The cost of occupational injuries and diseases in the mining industry in Quebec was estimated for the period of 2010 to 2012. The method used takes into account the financial and human costs assumed by employers, workers, and the community. To better direct research and prevention toward issues with the most significant consequences, the results are presented in various ranking tables, which stakeholders might find useful.RÉSUMÉ Le coût des accidents du travail et des maladies professionnelles dans l’industrie minière au Québec a été estimé pour la période 2010-2012. La méthode utilisée prend en compte les coûts financiers et humains endossés par les employeurs, les travailleurs et la communauté. Afin de mieux orienter les recherches et la prévention vers les problèmes ayant les plus graves conséquences, les résultats sont présentés dans divers tableaux de classement, qui seront d’une grande utilité aux parties prenantes. INTRODUCTIONThe mining industry is much safer today than it was 30 or 40 years ago, mainly due to a more qualified workforce, the use of automated equipment, and a corporate culture more focused on occupational health and safety (OHS); however, the number and the severity of occupational injuries and diseases continue to make this industry one of the most hazardous. In the province of Quebec, the mining industry accounts for approximately 0.4% of paid workers but is the source of 4% of fatal work accidents. It is, therefore, important to continue the prevention efforts already underway in the mining industry.The difficult global economy, which has affected the mining industry in the last few years, is an opportunity to reaffirm that sound management of OHS can have a positive impact on companies’ productivity and profitability. Occupational injuries and diseases are costly for the companies concerned and for society as a whole. Reducing their occurrence makes it possible to reduce not only the size of workers’ compensation board contributions but also several other financial and human costs."

Jan 1, 2018

By M. A. Trevits, G. Frampton

"Mine safety training materials have long included pictures of mine conditions, equipment, hazards, etc. These images are invaluable to both the trainee and the trainer to convey many important concepts. The human eye takes in a tremendous amount of information, while the field-of-view from a consumer grade camera is, generally, 40 degrees to 90-degrees. This difference in field-of-view is a primary reason that pictures, especially of dark and dusty areas, don’t adequately describe the scene. For conveying information to a trainee, these images lack context. Today, 360-degree cameras are available with consumer-grade cameras costing a few hundred dollars. Also, the display technology is already owned by most trainees and trainers and is widely available. The resulting 360-degree videos and pictures can be readily viewed on smart phones and inserted into Microsoft PowerPoint slideshows. These images and videos can easily be included in existing training modules, disseminated using the internet, and used by trainees easily. We propose a methodology for utilization of 360-degree video and images with simple display technology for miner training. INTRODUCTION AND BACKGROUND In mining, as in other production-related industries, the safety of workers is dependent upon many interrelated factors. One of the more important safety factors is a miner's ability to recognize hazards in their workplace. The ability to perceive and identify hazards is perhaps more difficult to master in underground mining than in general industry because the work environment is confined, noisy, dark, and inherently dangerous because of the hidden unknowns created by the geological setting and the conditions created by the mine opening. Further complicating the situation is a setting that is continuously changing as mining advances (Barrett 1995) [1]. Hours of excellent mine safety training have been developed and utilized over the years. Pictures of mines, activities, hazards, etc., are included in many of these training courses. These photographs, especially those taken underground, often lack context because of the limitations of the cameras and lenses. Notable research by the US Bureau of Mines and then later by NIOSH showed that the use of stereoscopic three-dimensional slides in training exercises was an effective aid for improving the ability of miners to recognize hazardous ground control conditions (Barrett 1988) [2]. An example of type of three-dimensional slides and slide viewer is shown in figure 1."

Jan 1, 2018

By T. P. Weldum, W. Conger

"These studies address the relationship between mill media sizing and its grinding efficiency. Starting with the results from a review of the literature, the issues of initial media sizing for a new ball milling circuit, and then optimal media sizing for an existing milling operation, were studied. The Functional Performance parameters “Mill Grinding Efficiency” and cumulative “Mill Grinding Rates” from both plant and test-scale equipment were used, and provide valuable new insight into this topic. A plant media sizing diagnostic tool is presented, as are newly developed testing equipment and evaluation methods, and recent case studies.REVIEW OF MEDIA SIZING LITERATURE For a plant metallurgist to answer the question “How can I maximize plant profit by manipulating this grinding circuit variable?” she must know what effect the variable has on grinding circuit efficiency. Despite the significant cost of grinding media and its potential effect on production capacity, the ‘best’ media sizing remains ill-defined for any given ball mill circuit in the industry today. The underlying reasons for this will be discussed. But the importance of this issue drove Metcom and its industrial partners to take on the challenge of how to engineer the ball charge for an existing grinding circuit. In the absence of any proven method, the first step was a review of the literature. Sponsored by Cleveland-Cliffs, Inc., a broad review of the literature was undertaken, producing “The Effect of Media Sizing on Ball Milling Efficiency” (McIvor, 1997). Among hundreds of publications that were reviewed that discuss the topics of media sizing or wear, forty-five were studied in detail. These were grouped into: plant experiences; laboratory and pilot plant investigations; media wear studies; population balance modeling studies; and general papers on ball milling which included the topic of media sizing. The reader is encouraged to refer to that review. The findings remain unchanged, although some relevant papers have been written since (e.g. Staples et al, 1997; Banasi et al, 1999; Orford et al, 2006; LaMarsh, 2015). The main findings of the review were as follows:"

Jan 1, 2018

By Steinar L. Ellefmo, Thomas Kuhn

The deep-sea ocean floor offers a great potential for mineral resources. The evaluation of these resources is both time consuming and costly and require as any resource evaluation data; geodata. The collection of hard data, physical samples, is of course preferred because the associated uncertainty is low. However, the collection of soft data or image derived data can offer a valuable supplement. In this paper image derived nodule uncertain abundance data from an area in the Pacific is utilized. Implementing these uncertain data improves the estimation when the quality of the estimation is measured using the classification indicators like the kriging standard deviation, the relative prediction error, the slope of regression and the weight of the mean. It is concluded that uncertain data is better than no data. INTRODUCTION The deep-sea offers vast mineral resources (Cathles (2011), Hannington et al. (2011), Hannington (2013), Singer (2014)). A mineral resource can according to increasing geological confidence be classified as an inferred, an indicated or a measured resource. The classification is performed by a competent- or qualified person and is dependent on the amount, quality and characteristic of available geodata. The competent person must have at least five years of experience relevant to both the style of mineralisation, the type of deposit and the performed task. Typical examples of a “task” is for example resource estimation and classification or planning- and execution of exploration activities and presentations of the results. The competent person must also be a member or a fellow of a professional organisation and thereby be bound by reporting code (-s) that defines minimum standards, recommendations and guidelines for public reporting.

Jan 1, 2018

By F. Chachula, A. Molinaro

"Sulphide mineral flotation operations continuously strive for a balance between mineralogy, mineral liberation, circuit conditions and reagent solutions to maximize the production rate and recovery of payable metals. The Taseko Gibraltar copper – molybdenum mill operations underwent an extensive project focusing on the fundamentals to identify the effects of process conditions and mineral liberation to improve the bulk circuit copper – molybdenum recovery efficiencies in the bulk flotation circuits. This discussion will provide process data that demonstrates; 1) fundamental relationship between mineral liberation to recovery and grade, 2) flotation circuit condition testing and optimization, 3) reagent combinations resulting in efficient/economical mineral recovery, and 4) the development of a xanthate free reagent solution. The data presented and discussed will also touch on flotation parameters including pH, retention time, kinetics and the effect on bulk circuit recovery performance.INTRODUCTION Taseko's is the owner (75%) and operator of the Gibraltar copper-molybdenum mine, located in south-central British Columbia, the second largest open pit copper mine in Canada and the largest employer in the Cariboo region. Taseko restarted Gibraltar in 2004. From 2006 until 2012, the company invested ~$700 million to expand and modernize the operation which was originally scheduled for demolition when the company acquired it in 1999. In the spring of 2011, construction commenced for Gibraltar Development Plan 3 (GDP3). GDP3 included the construction of a standalone 30,000 ton per day concentrator, built adjacent to the existing 55,000 ton per day facility. The new design capacity of Gibraltar was designed to be 85,000 tons per day. An integral part of the project was a new molybdenum recovery facility. In addition to the new concentrator, the mining fleet was upgraded with a new mining shovel, production drill and ten haul trucks (Taseko, May 2015). In May of 2015, the Company completed an updated mine plan for Gibraltar featuring a 50% decrease in strip ratio. This new mine plan was a result of a detailed, six-month engineering study and forms the basis of an updated NI 43-101 compliant reserve (Taseko Announces Improved Economics At Its Gibraltar Copper Mine, 2015). The new mine plan took into account lower milling costs as a result of the modernized processing facilities (Taseko, May 2015)."

Jan 1, 2018

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By Karsten Hagenah, Tor Jensen, Jens Laugesen, Øyvind Fjukmoen, Lucy Brooks

This paper describes operational environmental threshold levels for exploitation of mineral resources in the deep sea. Such criteria are needed to be able to monitor and control deep sea mining with respect to the stringent environmental requirements that are needed. It is recommended to use existing environmental threshold levels for comparable activities where such are existing. Fields of application are mainly but not exclusively seabed mining operation activities under the governance of the International Seabed Authority (ISA). The threshold levels and limits mentioned in this paper are proposed recommendations based on other activities than seabed mining but are a proven and accepted approach in other maritime industry activities. An example of such other activities with proven and accepted environmental threshold levels are Oil & Gas exploitation activities in the sea. Background The first exploitation of mineral resources is coming closer. At the moment regulations for exploitation for mineral resources in the Area are being developed by the International Seabed Authority (ISA). The ISA regulations will contain the framework related to environmental monitoring of exploitation. However, the regulations will not contain operational environmental threshold levels for the Contractor.

Jan 1, 2018

By N. Damiano, J. Noll, C. Zhou, J. DuCarme

"Preventing machine-related injuries is one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable were characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which cause little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects. INTRODUCTION An average of 250 injuries occur every year during operation of Continuous mining machines (CMMs), and 43 miners have been killed by striking or pinning accidents involving CMMs in the U.S. from 1984 to 2015 (Mine Safety and Health Administration, 2015). In addition, there have been 10 fatal accidents involving mobile haulage equipped with trailing cables from 2000 to 2015 (Noll et al., 2017). In response to these fatalities and injuries the Mine Safety and Health Administration (MSHA) promulgated a regulation in 2015 requiring the use of a proximity detection system (PDS) on all CMMs except full-face machines and proposed a regulation in 2016 which would require a PDS on other mobile underground equipment. Current PDSs approved for underground use are magnetic-field based. The PDS contains machine-mounted magnetic field generators that create fields around the machine. The other part of the PDS is a miner-wearable component (MWC) that reads the flux density of the generators. These systems use the magnetic field strength readings from the MWC to determine whether a miner is at a safe distance from the machine. A stable magnetic field is essential for the accuracy of the system."

Jan 1, 2018

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By O. Celep, H. Deveci, Ersin Y. Yazici, F. Ahlatci

"There are increasingly stricter environmental regulations imposed for use of cyanide leaching for the extraction of gold from ores. Alternative lixiviants to cyanide, preferably with low toxicity, have been extensively studied. Thiosulphate has emerged as one of the most suitable alternative leaching agent in place of cyanide due to its low toxicity and technical attributes e.g. fast leaching kinetics, high gold extractions from carbonaceous ores in particular. High solubility of most copper minerals in cyanide solutions results in low gold extractions due to excessively high consumption of cyanide. In contrast, low reactivity of copper minerals in thiosulphate solutions makes thiosulphate leaching potentially suitable alternative for treatment Cu-bearing gold ores. The extraction of gold/silver from a copper-bearing pyritic gold concentrate (62 g/t Au, 110 g/t Ag and 0.3% Cu) in thiosulphate solutions was investigated in this study. The concentrate is composed of predominantly quartz (25%) and pyrite (32.7%) as well as sphalerite (5.37%), galena (2.12%) and anglesite (1.13%). Other minor minerals are arsenopyrite, chalcopyrite, covellite and bournonite. Previous studies by the authors indicated that the concentrate did not respond well to cyanide leaching (i.e. 45-46% Au/Ag at 1 g/L NaCN). The effects of concentration of ammonia (0.2-1.5 M NH3), thiosulphate (0.1-0.75 M S2O3) and copper (0-20 mM CuSO4) on the extraction of gold and silver over 8 h. was investigated. Increasing the concentration of thiosulphate and ammonia substantially improved the rate and extent of gold leaching while high copper levels produced an adverse effect particularly at low concentration of thiosulphate (i.e. 0.1 M). Complete extraction of gold was achieved under suitable conditions. In contrast to gold, silver extractions remained consistently at low levels (i.e. 28%). These findings demonstrated that thiosulphate leaching could be used to achieve acceptable levels of gold extraction from the copper-bearing pyritic gold concentrate."

Jan 1, 2018

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By Leming Ou, Qiming Feng, Yiping Lu, Pengyu Zhang, Qing Shi, Kun Liu, Guofan Zhang

"This paper introduces the mineralogical analysis of certain polymetallic copper-zinc ore in China with the aim of improving the flotation process. The main valuable elements, mineral phases and compositions of run-of-mine ore were inspected by the X-ray Fluorescence (XRF) and chemical analysis. For a deep known of the old process defects, Mineral Liberation Analysis system (MLAs) was employed to investigate the minerals liberation degree of selected key slurry points. Analysis results show that the run-of-mine ore belongs to the original copper-zinc polymetallic symbiotic ore at low oxidative level, which mainly contains 0.16% Cu, 4.43% Zn and 0.88% Sn. Gangue minerals are mainly silicate minerals, and zinc mineral is sphalerite. MLAs test illustrates that about 86% sphalerite has been dissociated in zinc flotation feed. In the current flotation process, over grinding of sphalerite monomer and insufficient liberation of intergrowths are the key problems need to be solved imminently. Up to this point, a new process consisted of two steps roughing unit is submitted in this research. It contributes two positive effects on zinc flotation performance: (i) separating sphalerite monomer timely to decrease overgrinding; (ii) improving zinc minerals intergrowths liberation efficiency. Flotation results indicate that the zinc concentrate grade increased 0.90% and the recovery improved 0.96% in the new flotation processINTRODUCTION Mineralogical analysis mainly focusses on solving mineralogy problems in minerals processing, assisting in minerals behaviors prediction and control for separation engineering (Falkovich, et al., 2001; Hillier, et al., 2003; Schouwstra and Smit, 2011). Process defects searching becomes its ordinary work, and flotation optimization appears to be its targets gradually. For example, Lucky Friday mine company (Idaho America) fails to obtain qualified lead concentrate as the change of ore properties (Nadoll, et al., 2011). Mineralogical analysis ascertains that there are too many dissociated sphalerite, pyrite and gangue particles exist in lead concentrate. According to this, more cleaning units are added to solve problems effectively. Kanowna Belle mine (Australia) takes a flash circuit in operation successfully with the aim of optimize flotation process, under the helps of mineralogical analysis and industrial test (Newcombe, et al., 2013). Lotter N.O. (2011) gives a deep description on how mineralogical data assisting mineral processing engineers to design and optimize flowsheet. For decades, quantitative and automated mineralogy techniques (Andersen, et al., 2009; Gu, et al., 2012; Oghazi, et al., 2009; Yu, et al., 2007) get well developed and hugely improve the veracity and repeatability of minerals properties measurement. Among these, MLAs (Gu, 2003) provided by JKMRC (Julius Kruttschnitt Mineral Research Center) is critically acclaimed all over the world. This analysis system can measure mineral phases composition and content, particles size, minerals occurrence and liberation degree directly."

Jan 1, 2018

By R. S. Wang, S. Z. Zhou, L. Wan, K. W. Zeng, Z. J. Sun, W. G. Wu, Z. B. Qian, X. R. Zhang, Z. K. Hu, Y. Yu

"In view of the present situation that the traditional environment friendly depressants for galena aren’t very effective in the separation of mixed concentrate including copper sulfide and lead sulfide, this research describes a new environment friendly depressant PD-1 and investigates its effects and mechanism in the separation of chalcopyrite and galena. This study is carried out through flotation tests, analysis of infrared spectra and absorption measurements. It is shown that when O-isopropyl-N-ethyl thionocarbamate (Z200) is used as collector, chalcopyrite and galena can be separated in the presence of PD-1 under appropriate conditions. Therefore, it can be concluded that PD-1 has an excellent depression ability and great selectivity for galena. Meanwhile, analysis of infrared spectra demonstrates that PD-1 can strongly absorb on the galena surface by chemical interaction with Pb2+, while it hardly absorbs on the chalcopyrite surface. In addition, the results of absorption measurements reveal that competitive adsorption occurs on the galena surface between PD-1 and Z200, PD-1 can block the absorption of Z200 on the galena surface. However, PD-1 has a little effect on the absorption of Z200 on the chalcopyrite surface under above conditions. What’s more, the hydrophilic groups of PD-1 molecules can make galena effectively depressed. The results of mechanism analysis are in accordance with those of flotation tests.INTRODUCTION In the processing of copper-lead sulfide ores, the process, copper increase and lead reduction (Zhang et al., 2017) after reagents removal of rough concentrate produced by mixed flotation of chalcopyrite and galena, is usually adopted. However, as a result of tight symbiosis and the similar flotability of chalcopyrite and galena, the separation is difficult (Hu and Feng, 2006). There are 3 kinds of depressants for galena in the separation of chalcopyrite and galena concentrate,including dichromate, sulfite and combined depressants of organic or inorganic reagents (Wei, 2012). As dichromate would cause serious environmental pollution, it is gradually banned to be used in industry (Xu et al., 2017; Lin et al., 2017). what’s more, due to the need of acidic slurry, using sulfite is not conductive to the maintenance of equipment and stable production(Wang, 1999). As for the combined depressants, they also have disadvantages of complex pharmaceutical system and no ideal separation effect (Wei and Sun, 2008). Therefore, the development of new safe and effective depressants for galena is a research focus for researchers in the minerals processing (Chen, 2000). In this paper, a new type of organic depressant PD-1 is applied to the copper-lead separation process of ""copper increase and lead reduction"" using Z200 as the collector. In addition, the performances and mechanism of its depression to galena are studied emphatically."

Jan 1, 2018