Search Documents

By Henry Fay

LAWRENCE ADDICKS, New York, N. Y., (communication to the Secretary *).-There are two points regarding gun erosion on which I want to say a few words: The first is about the analogy to hardening of wire by drawing and the second the possible role played by thermal conductivity of the metal. The ductile metals do not necessarily become brittle when cold-worked as it is possible to draw copper from 3. in. in diameter soft rod down to the finest hair wire without annealing. This results, as stated in the paper, informing a hardened core with a very hard skin. The electrical conductivity is depressed some 3 per cent. and the tensile strength nearly tripled. A soft copper wire 0.08 in. in diameter and 6 in. long may be twisted 150 or more turns before the wire will snap under torsion. A hard-drawn wire will break after perhaps a dozen twists, the skin breaking down at one spot. Just wiping the wire with a cloth clamp with dilute nitric acid has a remarkable effect in increasing the number of twists without appreciably lowering the tensile strength, showing the skin to be very thin. On the other hand, pickling the rod, from which the wire is to be drawn, in dilute nitric acid also greatly increases the number of twists which can be applied to the resulting wire. This indicates that the copper oxide scale produced when the wire bar is rolled hot is more or less rolled into the rod and may have much to do with the skin effect. We also know that if the conditions of drawing are not correct, the heat of deformation in the die may produce quite an annealing effect. The application of this analogy to what occurs in a gun to produce the effects noted offers some difficulty. The second point is that as the temperature of the surface of the gun bore has undoubtedly a great deal to do with the amount of erosion, one natural remedy would be to conduct the heat away fast enough to keep this temperature within desired limits. This brings up the question of the thermal conductivity of the metal of which the gun is made. We know that the conductivity of pure metals is greatly altered by alloying and that the alloy is usually, though not always, lower in conductivity than the metal before alloying. This is interesting when it is considered that the high-nickel and manganese-steel alloys show greater erosion as stated. Would it not be instructive to study the question from the point of view of heat conducted away from the eroded surface?

Jan 3, 1917

By F. H. Willcox

IN Bessemer-steel practice, air is blow, through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and carbon. Toward the end of the blow, when the iron is not protected. from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Bessemer and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast irons is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blowholes lies in part in the presence of dissolved oxide of. iron in the

Jan 2, 1917

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is, desired and not include collateral natter which may not be of interest. The time spent in-searching for such collateral matter will be saved, and the information will be sent more, promptly and-in more usable shape.

Jan 2, 1917

By W. G. Matteson

IN 1915, the State of California passed a law of great scope and importance. This law has been in successful operation for., year and may be briefly described as an act "establishing and creating a department of. the State Mining Bureau for the protection of the natural resources of petroleum and gas from waste and destruction through improper operations in production; providing for the inspection of petroleum and gas wells; requiring all persons operating petroleum and gas wells to make certain reports" and providing the necessary officers and assessments-to carry out the provisions of the act. The statute provides for a separate department of the State Mining Bureau, under the general supervision of the State mineralogist, with a staff composed of a "state oil and gas supervisor" and four deputies. It rules that all petroleum and natural gas wells shall be drilled, operated or abandoned under the supervision of the State supervisor, who shall order such tests or remedial work as seems to him necessary to protect the interests of property owners and the general public. It also provides for a board of arbitration to consider orders given by the supervisor which are not acceptable to the well owner. Section 18 of the, act, which is the provision that is directly related to, this paper, requires "the owner of any well referred to in this act to keep a careful and accurate log of the drilling of such well;" and further requires that this log shall show the character and depth of the formations passed through or encountered in the drilling, particularly the location and depth of the water-bearing strata; the character of the water encountered (so far as ascertained); whether the water was shut off, and, if so, at what point; that it shall show completely the amounts, kinds and size of casing used; the depth at which oil-bearing strata are encountered; the depth and character of the strata, and whether all water was successfully and permanently shut off so as to prevent percolation or penetration into the oil-bearing strata. -

Jan 2, 1917

Clarence M. Haight, Franklin Furnace, N. J. (communication to the Secretary*).—In that part of Mr. Wilson's paper describing the Gilman cut-and-fill system, a few features do not appear to be fully explained. In what way is the waste used for filling obtained? The text mentions that if waste is encountered when driving the filling raises, these raises are stopped until the fill is needed; that seems to suggest mining the capping for fill, which might make the backs of the stopes bad as the stopes approach the top of the ore. If, on the other hand, the fill is brought to the raises in cars, are the crosscuts that are necessary in ore or waste? Is the cost of this fill included in the stoping costs given? The second, or lower, series of stopes will present a different problem to that which the first series (under the capping) gave. Although no mention is made in the text, it would seem that the second series of stopes will have to be worked on center lines which are offset half the stope width, 20 ft., from the centers of the stopes above, in order to take advantage of the "rafter" effect of the stringers so named. How is the fill to be introduced into the lower stopes? There are no crosscuts mentioned to provide for this; or is it intended to tap the filled stopes above for the fill? In the latter case the method of control of this fill will be of interest. Ore that will admit of a stoping width of 40 ft. with the lengths mentioned in the description is stronger than any with which many mining men are familiar. Has the practice of starting to mine a second stope before the preceding one is filly completed been tried to any extent? If

Jan 1, 1917

By Joseph T. Singewald

The possible value of the red hematite iron ore of the southern Appalachian States, if some practicable method of concentrating it could be devised, has long been recognized. The ore is very low grade, and although in enormous quantities, particularly in the States of Alabama, Tennessee, and Georgia, is only at a few points rich enough to work, and even the best of it ranks among the lowest grade iron ores being mined in the United States. A cheap method of beneficiating this ore would make enormous quantities available and vastly increase the iron-ore resources of the country. However, this low-grade ore in effect constitutes a potential iron reserve, and as long as ample quantities of ore can be obtained elsewhere the question of its utilization does not demand immediate notice. Where these ores are in part of workable grade, however, a problem of more immediate importance arises which, from considerations of economy and prevention of waste in their mining, ought to be solved or, at least, attacked as quickly as possible. Where these ores are being worked they are usually intimately associated with lower-grade material that in mining is left behind. The difficulty and expense of going into ground broken by old workings makes the recovery of this lower-grade ore practically impossible and it is lost forever. Success in concentrating the red ores, therefore, would save material that is now being irretrievably lost. The successful large-scale concentration of law-grade ore in the last few years on the Lake Superior iron ranges should encourage the attack of similar problems in the Birmingham district.

Jan 1, 1917

By Richard A. Conkling

A shale layer, buried beneath two or three thousand feet of strata, in some instances, will upon folding become thicker in the synelines and thinner on top of the anticlines. This can be accounted for, in part, by the stretching on the crests of the fold and the compressing in the troughs; but this will by no means account for all of it, as is shown in the example herein set forth. It is my firm belief that the rest of the thickness is due to flow. What causes the movement, however, does not concern us here, SO long as there is movement, for this article purposes to show its effect upon the producing area of different sands. It is the author's hope, in this way, to drop a hint or two that may be valuable to the oil geologist, in making estimates of future productions and values of oil properties. An example will be given from property in the famous Gushing Pool in northeastern Oklahoma, where the author has had occasion to make a detailed study before recommending some property to his company, and has then been able to watch the results of this work. The author never mapped the surface structure in this pool, as this had been done by Frank Buttram when he was with the Oklahoma Geological Survey. We are using, therefore, a section of his map in this article for our surface contours. The main east dip comes farther east than this section shows. From the 10-ft. contours in Fig. 1, it will be seen that the surface folding is very slight, but in the contour map of the Bartlesville sand (Fig. 2), which was the greatest producing sand, we see much more complex folding. It seems that the folding becomes greater with the depth. Folding may have started in Middle Pennsylvanian times and continued through the Upper Pennsylvanian which is found at the surface. This may, or may not, have been the cause of the increase of folding with depth. However, the fact that mostly concerns us is the interval of shale between the Bartlesville sand and the Tucker sand. The Tucker is the next productive sand below the Bartlesville. Not enough wells have been drilled to the Tucker sand to make a contour map of it, but

Jan 1, 1917

By C. E. Arnold

In attacking the problems of mining and treating large disseminated copper orebodies such as those occurring in the Miami or the Ray district of Arizona, one of the vital questions to be decided is, "What is the value of the orebody per ton in place?" The importance of this question lies in the fact that its answer helps to reach a decision concerning the method of mining to be employed. Let it be assumed for the moment that milling and smelting practice, especially the latter, is more or less standardized, and has a cost incapable of much variation, while the cost of mining has a considerable range owing to the large number of mining methods by which a mine may be exploited. For instance, a method may be adopted whereby all the available ore can be extracted perfectly clean (i.e., unmixed with barren material) at a relatively high cost; or a method may be used involving the necessary dilution of a portion of the ore with waste, in order to recover that portion, thus giving a relatively poorer extraction but nevertheless a lower working cost than the former method. Naturally, between these two extremes there lie intermediate methods. In order to arrive at a solution of a mining method problem that is of any value, it is necessary that accurate and complete estimates of mining, milling, and smelting performances and costs shall be established. By way of illustration is given a case of mining, by the system of undercutting and caving, a large orebody with an average content of 1.50 per cent. copper supposedly all in sulphide form, to which case has been applied those results in mining operations which one may fairly assume are to be expected when viewed in the light of G. R. Lehman's ore-drawing experiments, which form the subject of a paper to be presented at this meeting. It is assumed that the total costs will be as shown in the table on page 204. To attain these costs, a daily production and treatment of 14,400 tons has been assumed. Other assumptions are as follows: 15 per cent. of orebody is to be extracted clean by development work and undercutting; 63.8 per cent. (75 per cent. of 85 per cent.) is to be extracted clean by caving, leaving 21.2 per cent. part of which is to be extracted by diluting with waste, and the remainder lost. Dilution and extraction are to

Jan 1, 1917

By W. G. Matteson

In 1915, the State of California passed a law of great scope and importance. This law has been in successful operation for a year and may be briefly described as an act " establishing and creating a department of the State Mining Bureau for the protection of the natural resources of petroleum and gas from waste and destrucbion through improper operations in production; providing for the inspection of petroleum and gas wells; requiring all persons operating petroleum and gas wells to make certain reports" and providing the necessary officers and assessments to carry out the provisions of the act. The statute provides for a separate department of the State Mining Bureau, under the general supervision of the State mineralogist, with a staff composed of a "state oil and gas supervisor" and four deputies. It rules that all petroleum and natural gas wells shall be drilled, operated or abandoned under the supervision of the State supervisor, who shall order such tests or remedial work as seems to him necessary to protect the interests of property owners and the general public. It also provides for a board of arbitration to consider orders given by the supervisor which are not acceptable to the well owner. Section 18 of the act, which is the provision that is directly related to this paper, requires ('the owner of any well referred to in this act to keep a careful and accurate log of the drilling of such well," and further requires that this log shall show the character and depth of the formations passed through or encountered in the drilling, particularly the location and depth of the water-bearing strata; the character of the water encountered (so far as ascertained); whether the water was shut off, and, if solat what point; that it shall show completely the amounts, kinds and size of casing used; the depth at which oil-bearing strata are encountered; the depth and character of the strata, and whether all water was successfully and permanently shut off so as to prevent percolation or penetration into the oil-bearing strata. This log is to be kept in the local office of the owner or operator, subject to the inspection of the supervisor or any of his deputies at any

Jan 1, 1917

By L. O. Howard

What was perhaps the first attempt at basic converting in the Southwest was made by the late Charles F. Shelby at Cananea early in 1907, when he removed the acid lining from one of the 8 by 12-ft. barrel-type converters then in use at the reduction works of the Cananea Consolidated Copper Co. and substituted a lining of one course of magnesite brick. In this shell, he blew 21 taps (about 180 tons) of matte to white metal before the brick gave out along the tuyhre line. In every case, the white metal so made was transferred and blown to copper in other converters. The cost of the lining was $700 and Mr. Shelby gave up the experiment as impracticable. No further serious effort to bessemerize copper mattes in a vessel having a more or less permanent lining of basic brick was made by any of the large copper smelters in the Southwest until some months after Messrs. Peirce and Smith had brought the question permanently before the public, and had proved it to be a metallurgical and financial success by their work at Baltimore and Garfield. Early in 1911, the Cananea Consolidated Copper Co. had in operation at its reduction works at Cananea, Mex., several 8 by 12-ft. barrel-type converters lined with magnesite brick which had previously been operating with acid linings. In the 18 months following, these converters produced 50,000 tons of copper. In June, 1912, this company installed the first of its new equipment of six stands of electrically operated 12-ft. Great Palls type converters, and shortly afterward discontinued the use of the smaller shells. In September, 1911, the Consolidated Kansas City Smelting & Refining Co. had installed at its El Paso plant two 10 by 26-ft. Peirce-Smith converters. Later, in March, 1913, one standard Great Falls type converter was added. About the time the Peirce-Smith converters were going in at El Paso, the Calumet & Arizona Mining Co. was experimenting with basic linings in 7-ft. by 10-ft. 6-in. barrel converters at its plant in Douglas, Ariz. These efforts were sufficiently successful to enable the plant to "handle the total output of copper in these small shells until the standard Great Falls converters were substituted in June, .1914.

Jan 1, 1917

By Henry M. Howe

The brilliant and very original matter in Professor Jeffries' discussion† should rank not only as an independent paper, but as a most important one. In particular, the explanation which it gives of the remarkable Sauveur phenomenon, over which so many of us have puzzled long and hard, is so clear, complete, and cogent as to go far toward establishing Professor Jeffries' hypothesis. The very leatures of Professor Sauveur's photographs which fit this hypothesis so exactly are reproduced in Chap-pell's photographs of steel coarsened under somewhat different conditions.' The ideas developed by these discoveries are so novel that convenicnce of language seems to call for new conventional terms for expressing them. In what follows here I propose certain terms for this end, for criticism and improvement, and I attempt to generalize from Professor Jeffries' hypotheses. Generally speaking, a given set of grains which undergo no growth in the cold will, when the temperature is raised progrcssively, start to grow on reaching a certain temperature, and will continue growing at all higher temperatures. The "germinative" temperature is that at which growth begins, quite as the conditions which cause a seed to grow are "germinative." We have then an inert temperature range below the germinative temperature, and a growth range above it, the germinative temperature being the limit between these two ranges. So, too, a germinant grain is one which is at its germinative temperature, and hence beginning to grow, while inert grains are those below their own germinative temperature, and the term "growing grains" includes those which are germinant and those which are above their germinative temperature. These last could be called " supergerminant" if the distinction should be needed. "Germinative temperature" seems better than "critical temperature

Jan 1, 1917

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

By F. H. Willcox

In Bessemer-steel practice, air is blown through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and cafbon. Toward the end of the blow, when the iron is not protected from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Besserner and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast iron. is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blow holes lies in part in the presence of dissolved oxide of iron in the molten steel and its consequent reaction with the carbon of recarburizers, when these are added, to form gases. (Another factor in the origin of blow holes is, of course, the solubility of gases themselves in the steel and

Jan 1, 1917

By Guilliaem Aertsen

The derivation of the word tire (or tyre, as it is spelled in England) is obscure. Some dictionaries suggest that it is the aphetic form for "attire, covering," so called as being the outside covering or band of a wheel; also as a corruption of "tier," the band which holds, or "ties," the rest of the wheel together. One dictionary states: "The supposed derivation of the word is that bands were first used on wheels in the City of Tyre, Syria." In the infancy of railroads, the tracks consisted of flat bars of iron, spiked or bolted to the upper surfaces of longitudinal timbers, which, in turn, rested upon masonry foundations. Stone blocks installed for this purpose on the old Germantown & Norristown Railroad, now the Chestnut Hill branch of the Philadelphia & Reading Railway, were to be seen for many years on the right-of-way, north of what is now Wayne Junction, Philadelphia, Pa. The "cornerstone" of the Baltimore & Ohio Railroad was laid Apr. 4, 1828, and the fist locomotive in America was built by Peter Cooper at the St. Clair Works, Baltimore, Md., in 1829 "to demonstrate its adaptability to a curved road." It is believed that the first successful locomotive was built in Philadelphia by Tyler & Baldwin in 1832 for the Germantown & Norristown Railroad. Rufus Tyler and Matthias Baldwin were brothers-in-law; the latter's name will be identified with American locomotives until locomotives are forgotten. The wheels on these first locomotives, designed to run on this primitive rail, mere shod with plain iron bands, bent and welded. The flanges consisted of separate iron bands, bent sidewise,welded, and bolted to the sides of the wooden fellies, or rims. Before many years had elapsed the tires were fabricated of iron bands, rolled in one piece with the flange projection on the side. The tire for each wheel was bent and welded and subsequently attached to the wheel center by shrinkage, bolts, rivets and various mechanical devices. Germany is generally given the credit for first making such tires of

Jan 1, 1917

THE Phillips River gold and 'copper field is situated on the south coast of Western Australia, about 200 miles east of Albany, 180 miles west of Esperance, and: 250 miles south of Southern Cross, forming the southern extremity of what Mr. H. P. Woodward classes as the fourth belt of Pre-Cambrian rocks, and the first auriferous belt, whicf extends northward through Southern Cross, Mount Magnet, and Cue. The field may be considered the premier copper producer of the State. The first mineral discoveries were made about 1892; when gold, copper, and iron pyrites were found; but, owing to the isolation of the district and the scarcity of water, both in the locality and on the route thereto, little work was done for some years. In1899, however, payable gold reefs were opened up, and the district began to attract attention.The southern portion of the district is composed of limestone and sandstone rocks, forming the coastal series, and is for the most part flat, broken only by a few low hills and ridges, except to the west, where Cape Barren and Eyre's Range stand out...

Jan 1, 1917

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By Frank Van Horn

IT is customary to ascribe two general modes of occurrence to natural gas, namely shale. gas which, as the name indicates, is found in' shale, and reservoir gas, which occurs ill sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts.

Jan 1, 1917

By Frank R. Van Horn

It is customary to ascribe two general modes of occurrence to natural gas, namely, shale gas which, as the name indicates, is found in shale, and reservoir gas, which occurs in sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts. Historical Outline The oldest well producing reservoir gas in the district was drilled in 1886 in Newburg for what was then known as the Cleveland Rolling Mill Co. This well was 3,000 ft. deep, and was thought to have reached the "Clinton" formation. Two "sands" showing small amounts of oil were recorded in the Niagara limestone at depths of 2,658 and 2,686 ft. This is about the horizon of the so-called Newburg sand which has proved to be of some importance as a source of gas and oil by recent drilling operations. The rock pressure was reported to be 400 to 500 lb. per square inch, but since the volume was only 14,000 to 16,000 cu. ft. daily, the well was not only considered unsuccessful but was thought to prove the absence of high-pressure gas in commercial quantities in the Cleveland district.

Jan 1, 1917

By Guilliaem Aertsen

THE derivation of the word tire (or tyre, as it is spelled in England) is obscure. Some dictionaries suggest that it is the aphetic form for "attire, covering," so called as being the outside covering or band of a wheel; also as a corruption of "tier," the band which holds, or "ties," the rest of the wheel together. One dictionary states: "The supposed derivation of the word is that bands were first used on wheels in the City of Tyre, Syria. " In the infancy of railroads, the tracks consisted of flat baits of iron, spiked or bolted to the upper surfaces of longitudinal timbers, which; in turn, rested upon masonry foundations. Stone blocks installed for this purpose on the old Germantown & Norristown Railroad, now the Chestnut Hill branch of the Philadelphia & Reading Railway, were to be seen for many years on the right-of-way, north of what is now. Wayne Junc-tion, Philadelphia, Pa. The "cornerstone" of the Baltimore & Ohio Railroad was laid Apr. 4, 1828, and the first locomotive in America was built by Peter Cooper at the St. Clair Works, Baltimore, Md., in 1829 "to demonstrate its adaptability to a curved road." It is believed that the first successful locomotive was built in Philadelphia by Tyler & Baldwin in 1832 for the Germantown & Norristown Railroad. Rufus Tyler-and Matthias Baldwin were brothers-in-law; the latter's name will he identified with American locomotives until locomotives are forgotten. The Wheels on these first locomotives, designed to run on this primitive rail, were shod with plain iron bands, bent and welded. The flanges consisted. of separate iron bands, bent sidewise, welded, and, bolted to the sides of the wooden follies, or rings. Before many years had elapsed the tires were fabricated of iron bands, rolled in one, piece with the flange projection on the side. The tire for each wheel was bent and welded and subsequently attached to the wheel center by shrinkage, bolts, rivets and various mechanical devices.

Jan 1, 1917

By M. D. Cooper

FOr the purpose of obtaining some first-hand data in regard to the shooting clown of coal in bituminous 'nines, it was the writer's good fortune to be employed as a shot-firer for almost one year. In all, 6,020 shots were fired by him during this period. All of the work was clone in what is known as the South Main section of the No. 2 Mine of the Ellsworth Collieries Co., Ellsworth, Pa., a subsidiary of the Lackawanna Steel Co. Position of Shot-firing in the Cycle of Operations The established practice of the Ellsworth Collieries Co. calls first for the undercutting of the coal by electric chain machines across the face of the entry or room. This is followed by replacing any posts removed by the machine-runners, or the setting of new posts or timber, as may be required. After this has been done the machine cuttings are loaded into cars. Then the coal is spragged, and a shot hole drilled to the depth of the undercut. Next in order, the shot-firer loads the hole and fires the charge. The working place is then cleaned up, timbered if necessary, the sides and face squared up, and loose material taken down. The face is again ready to be undercut.

Jan 1, 1917