Search Documents

By Robert E. Schock, Eric J. Risberg

"Less than 20,000 years ago, the last of the glaciers retreated from the Chicago region. They left behind sheets of glacial clay till underlain by dense, over-consolidated till (“hardpan”) below which is the limestone bedrock, found about 100 ft (30.5 m) below street level. The most notable feature in this profile is the unusually soft clay till that has historically been called “Chicago Blue Clay.”But the founding fathers of Chicago really didn’t care about what was under the ground. They recognized the importance of the city’s location as a potential trade and transportation hub. With access to the East through the Great Lakes and access to the West through the Mississippi River system, the viability of the city was evident. Chicago’s population grew rapidly. The city continued to grow through the Civil War years, but was dealt a devastating blow in 1871 by the Great Chicago Fire, leaving the city in ruins. The Birth of the SkyscraperAfter the cleanup of the Great Fire came the first real building boom in Chicago’s history. During this era, buildings were generally founded on shallow footings bearing on sand or clay. Many multistory buildings were constructed between 1880 and 1890 on spread footings. The first tall buildings were constructed with load bearing masonry walls. These early tall buildings suffered significant settlement as the soft clay underwent consolidation.The Home Insurance Building, built in 1885, was 12-stories tall and is generally acknowledged to be the first “skyscraper” in the U.S. It was the first building constructed with an iron skeleton frame instead of load bearing masonry walls. Spread footings were used under the interior columns in an effort to better distribute the loads, but the building still experienced large settlements.Construction began for the Monadnock Building in 1891. The 17-story building was built using load bearing walls 7 ft (2.1 m) thick, supported on rail-grillage footing foundations. When completed in 1893, the Monadnock Building boasted the title “World’s Largest Office Building.” The total building settlement over the past 125 years has been measured at over 20 in (0.51 m). The engineering community in the late 19th century observed settlement, but did not yet understand the process of consolidation of the soft clay beneath the city. During this time, many of the new buildings required structural repairs during and after construction; the problem was especially acute in buildings where highrise towers joined lower podium structures."

Jan 1, 2016

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require that refuge alternatives (RAs) are located within 305-m (1000-ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature (AT) below 35°C (95°F). The National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from the RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for mobile tent-type RAs. The results of these studies show that most of the heat loss from the RA to the ambient mine is due to radiation (51%) and conduction (31%). Three mine width/height configurations and three mine strata compositions were examined. The final DBT inside the RA after 96 hours varied less than 1°C (1.8°F) for the three mine width/height configurations and less than 2°C (3.6°F) for the three mine strata compositions. INTRODUCTION Following a mine disaster, workers will try to escape the mine. If their escape is futile, they can take shelter in a refuge alternative (RA). In 2008, the Mine Safety and Health Administration (MSHA) mandated RAs in mines to ensure that a safe and livable shelter is provided for a minimum of 96 hours, and that the apparent temperature (AT) does not exceed 35°C (95°F) inside the RA [1]. An ongoing concern with RAs is the potential to exceed this limit. The temperature rise inside an RA is due to the metabolic heat released by the occupants as well as heat released by the carbon dioxide scrubbing system. The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type training unit RA in its Safety Research Coal Mine (SRCM) to investigate heat buildup in RAs. The 10-person capacity for the tested RA is based on 1.4 m2 (15 ft2) of floor space per miner. NIOSH-developed simulated miners, which are heat input devices that generate both sensible and latent heat, were used to represent the metabolic heat generation of an average miner (117 W) for testing in the SRCM. It was found that the number of occupants in an RA may need to be reduced based on the ambient mine temperature, which varies from mine to mine [2]. To further research temperature rise inside an RA, ThermoAnalytics, Inc. (TAI) was contracted by NIOSH to perform thermal simulations of the tested 10-person mobile tent-type RA. TAI developed a thermal model of the SRCM using RadTherm software, which incorporates a human thermal model (HTM) to represent the equivalent metabolic heat loss of a miner within the RA’s enclosed environment. The thermal model was previously validated by comparing simulation results with test results [3]. During a mine disaster in which miners would have to take shelter in an RA, mine ventilation may not be available. As such, mine ventilation was off for both the testing in the SRCM as well as in the simulations. This paper discusses the heat loss mechanisms and the effects of mine strata composition and mine width and height associated with a ten-person tent-type RA."

Jan 1, 2016

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By D. Berberick, G. Sturgis, M. Board, B. Strickland

"Hecla Limited is nearing completion of the Lucky Friday Mine No.4 shaft located in Mullan, ID. The shaft is collared at the 4940 level of the mine and will have a final mine level depth of 8620, or 9,590 feet below the surface. After reaching the 7400 mine level the shaft encountered ground deformation higher then allowed for in the design for a circular shaft excavation and concrete lining. This additional ground deformation required portions of the shaft concrete liner to be reinforced with frameless, steel liner plate. To eliminate the installation of the liner plate from the remaining shaft development, the design of the shaft excavation starting at the 7650 mine level was changed to an elliptical cross section based on the overall stress field orientation as well as the orientation of the structure of the host rock surrounding the shaft. The elliptical cross section was instrumented to confirm the shaft excavation and lining was performing as designed. This design change has allowed the shaft to continue to the planned 8620 mine level without the need to install liner plate in the shaft or change the overall functionality of the shaft or the Lucky Friday life of mine plan.INTRODUCTION Hecla’s Lucky Friday Mine is a deep, underground producer of silver, lead and zinc in the Coeur d’Alene mining district of northern Idaho (Figure 1). Primary access into the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk to an original depth of 1,890-m (6,200-ft). Current production is from the Gold Hunter vein system, approximately 1,525-m (5,000-ft) northwest of the Silver Shaft.Lucky Friday’s #4-Shaft is a 5.5-m (18-ft) finished diameter, internal shaft, or winze, being sunk to the north of the Gold Hunter vein system, from the mine’s 4760 level, 1,743-m (5,720-ft) below the surface, to the 8620 level, 2,923-m (9,590-ft) below the surface. The shaft is designed to provide access to the deep, high-grade zones of the Gold Hunter in order to increase the mine’s production and operational life. Design and engineering began in 2006, with construction starting in the fourth quarter of 2009."

Jan 1, 2016

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

By G. Kleyn

"Sub-standard practices and their adverse impact on safety performance remain a challenge in the South African gold mining industry. The purpose of this study was to investigate the root causes of sub-standard practices and the effect on safety performance in South African gold mines. The focus of the study was on the underground production operations at a gold mine in the Free State. The study consisted of three parts: a personal investigation into the causes of sub-standard practices at the mine, a comparison with the results of a cultural study performed at the West Wits mines, and a behavioural survey.The studies described in this article yielded similar results in terms of the key drivers behind sub-standard practices. It was found that substandard practices had a number of causes, and the origin lies within the habits, attitude, and behaviour of employees. Current methods of addressing sub-standard practices and improving safety performance were found to discourage employees from performing work safely and according to procedure. It was concluded that the lack of critical behavioural habits for the given work environment and job title could possibly be the primary reason for the occurrence of sub-standard practices. IntroductionSince the implementation of the Mine Health and Safety Act, 1996 (Act 29 of 1996) and the Mine Health and Safety Regulations, the South African mining industry has been striving to improve health and safety performance and has placed great emphasis on adherence to mine standards.The Act requires employers in the mining industry to report accidents, incidents, and dangerous situations to the Regional Principal Inspector of Mines in their area. The data provided by employers is captured and analysed by the South African Mines Reportable Accident Statistical System (SAMRASS) and made available for public viewing (Department of Mineral Resources, 2011).A review of the national mine-related accident statistics shows clearly that the South African gold mining industry has improved its safety performance markedly over the past decade, but is still facing major challenges (Figure 1). These include meeting the Mine Health and Safety Milestones (Department of Mineral Resources, 2011)."

Jan 1, 2016

By T. Karlkvist, H. R. Kota, F. Andreas, B. I. Pålsson

"Separation of different calcium minerals have long been an interesting and challenging problem. In this investigation calcium mineral separation is examined by: microflotation, zeta potential measurement and adsorption, using novel collectors having two functional groups instead of one. In theory, by varying the distance between the functional groups, it could be possible to preferentially target one calcium mineral by matching the spatial distance between the sites on the mineral surface. In this investigation two new surfactants have been tested to estimate their ability to float apatite and/or calcite. Preliminary findings show that an increase in distance between the functional groups favors one mineral over the other, and this might be due to differences in the mineral surface structure. INTRODUCTION Apatite is a strategically important mineral which has both great value for industrial use as a precursor to phosphoric acid; and in the agricultural industry as an important source of phosphorous in fertilizers. This has led both the European Union and the United States to recognize it as an important resource for the future. Currently there is no lack of apatite in the world, but it is important to develop the beneficiation to ensure future supply. A common problem in apatite flotation is the selectivity towards calcite, which it is commonly associated with. Although calcite is an important industrial mineral its abundance makes it not usually worth to extract from apatite ores unless it is easy to separate1,2. Both apatite and calcite are semi soluble minerals with calcium as one of their constituents. The most common way to separate apatite and calcite is to use flotation. A process that involves making the mineral particles to extract from the system hydrophobic by adsorbing a collector on the mineral surface. One way to study collector adsorption on a mineral surface is by zeta potential measurements. The zeta potential is the charge at a slip plane a short distance from the surface. By measuring the zeta potential with and without the presence of collector it is possible to investigate if the collector is present at the surface or not, a change is indicative of collector adsorption. The zeta potential of fluorite, apatite and calcite without collector can be seen in Figure 1. The small difference in zeta potential between apatite and calcite shows the similarity in their surface properties and gives an indication of their separation difficulty. One additional problem with semi soluble minerals is their tendency to slightly dissolve in the pulp and thereby change the ionic composition of the solution. This makes separation and research problematic as the freed ions may readsorb on the mineral surface and interfere with the collector adsorption on the mineral surfaces3–5."

Jan 1, 2016

By K. M. Mohamed, I. B. Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to reduce rib fall accidents and fatalities in underground coal mines. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified. The paper presents a coal rib model to simulate the mechanism of the coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff mine in Australia. Fracturing of the coal rib was defined by critical values of shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data. INTRODUCTION Coal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities [1]. Despite the threat of rib falls, the amount of rib falls and rib support research conducted in the U.S. is limited compared with what has been done in pillar and roof support design. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in coal mines to minimize the number of rib fall accidents and fatalities in underground coal mines."

Jan 1, 2016

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Dialkyl dithiophosphinates are a unique class of collectors used in the flotation processing of Cu- Au, complex polymetallic, and precious metal ores. They are known to exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive HSE profile. Historically, for most reagents used in flotation, practical methods of chemical usage have preceded detailed scientific understanding of how they work; this applies also to dithiophosphinates. Recently, however, the research community has shown significant interest in this chemistry, and numerous studies have been conducted to understand the fundamentals of interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized by drawing on concepts and insights from coordination chemistry. A comparison between the interactions of dithiophosphinates and dithiophosphate analogues with various minerals and metals is also made throughout. We believe that such a critical analysis/overview will be invaluable in identifying gaps in knowledge regarding this important set of compounds, which in turn may provide a basis for the design of studies that can advance understanding of their flotation performance. INTRODUCTIONDialkyl dithiophosphinates are an important member of the class of thiophosphorus compounds that are widely used in flotation beneficiation of base metal sulfide and precious metals ores. Ore flotation studies and plant practice experience have demonstrated their unique properties compared to the traditionally used sulfide collectors such as dialkyl dithiophosphates (their closest analogues) and xanthates. The predominant dialkyl dithiophosphinate used in the industry today is sodium diisobutyl dithiophosphinate (a.k.a. DIBDTPi; AEROPHINE® 3418A1 introduced by American Cyanamid in the late 1970s; Figure 1). The widest application of AEROPHINE 3418A is found in complex polymetallic ores of Cu-Pb-Zn-Ag, Pb-Zn-Ag, and Cu-Zn where it has demonstrated improved recoveries (and flotation rates) of sulfide minerals of Cu, Pb and Ag and selectivity against sphalerite, iron sulfides, and penalty elements (Mingione, 1991). More recently, it has also been used as a collector in the processing of Cu, Cu-Ni, and Ni ores (Guitard et al., 2015) and Cu-Au ores (Dunne, 2005). In general, it is considered to possess the collecting power of xanthates together with the selectivity (against pyrite) of dithiophosphates (Hope et al., 2003a, 2003b), while requiring lower dosages than those reagents (Guitard et al., 2015). AEROPHINE® 3418A has also found an important place in several targeted formulations to improve flotation performance. Other benefits of this reagent include higher flotation rates, having a better HSE (health, safety and environmental) profile2 compared to xanthate, and exhibiting resistance to hydrolysis and oxidation (Guitard et al., 2015). Compared to diisobutyl dithiophosphate (DIBDTP), which is known to contribute significantly to frothing (often leading to over-frothing), AEROPHINE® 3418A is observed to be froth neutral (i.e. it does not alter the existing froth characteristics). As is the case for other flotation reagents, the design and application of AEROPHINE® 3418A has preceded understanding of its behavior at a fundamental level. Recently, there have been numerous fundamental and application studies designed to develop a better understanding of its interaction with sulfide minerals and precious metals. This should help in optimizing its application in flotation and provide a basis to better rationalize its unique selectivity and activity characteristics. Past studies on the interacti"

Jan 1, 2016

By T. H. Etsell, P. Kerr, Qi Liu

"The objective of this investigation was to study the reaction mechanisms during the reduction of iron oxides in the presence of calcium chloride and carbon black as a simplified iron segregation process. The gas phase was analyzed by mass spectroscopy and the solid reaction products were analyzed by scanning electron microscopy. Mass spectroscopy, combined with thermogravimetric analysis and differential scanning calorimetry, revealed the presence of several gases at elevated temperatures over time, and the scanning electron microscope in combination with energy dispersive X-ray analysis illustrated the growth of a metallic iron phase on or near the carbon substrate. The results correlated well with similar copper and nickel segregation processes, but also introduced new insights that challenge the simplicity of the current models. The formation and transport of gaseous iron species to the carbon substrate in the presence of steam and hydrogen were evident during the reduction process that was studied; however, there is more happening at a mineralogical level, based on evidence of a liquid phase resulting in substantial growth due to an apparent fluxing effect created by the calcium chloride.These results help to better explain the chemical reactions and, in turn, the thermodynamics and kinetics of iron segregation processes related to the beneficiation of low grade complex iron ores. The results are also applicable to the production of metallic iron and concentrated titanium dioxide from ilmenite ores. The benefit of this process is that it allows ores in which the iron minerals are intimately associated with gangue minerals to be processed in circumstances where conventional mineral processing techniques are unsuitable or incapable of upgrading the material."

Jan 1, 2016

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By N. V. Moraka

In dealing with transformational aspects, the South African Constitution aspires for a balance between attempts to broadly represent the country’s demographics in the way in which organizations are structured and the need to maintain the necessary skills to ensure continual retention of skills for optimum and efficient organizational performance. Through the Mining Charter, government aimed to redress gender and racial imbalances in the mining industry as part of transforming the demographic representation of mining companies to include black people, women, and people living with disabilities in all job levels up to top management. While the Constitution calls for an appropriate balance between demographic representation and competency, this aspiration for mining poses challenges for companies due to the proficient and competent skills needed in this industry. To this end, the South African mining industry has been subjected to substantial criticism from government regarding the slow progress of transformation. The mining industry justifies its slow pace of transformation by pointing at inconsistent, varying legislation and definitions governing transformation, limited skills available from historically disadvantaged groups, and cautioning not to compromise the sustainability of mining companies by marginalizing white males and white youth with the objective of addressing racial imbalances. This lack of understanding between industry and the government has led to considerable confusion regarding the accountability of stakeholders in transforming the industry. This article presents the perspectives of ten mining executives on transformation in the South African mining industry. The theoretical description of transformation, as well as other mining stakeholders’ interpretations of transformation. is presented. Qualitative data from interviews with mining executives demonstrates their understanding of transformation through rich descriptions, interpretations, and implications in their contexts. The findings demonstrate that transformation in the mining industry is not simply about race and gender, but about cultural change, a change in mind-sets, embracing diversity, equalizing rights and opportunities, and attaining social justice. Moreover, transformation is clearly a gradual process. The article concludes with a recommendation for the definition of transformation to be corroborated with the views of mining executives and that of the Constitution of South Africa. This will create an overarching, simplified definition of transformation that can be accepted and interpreted by all stakeholders.

Jan 1, 2016

By Ignazio Carbone

"During the design of a typical modern subway, engineering aspects prevail since underground structures remain hidden to most humans. Aligning the advanced architectural concepts with the engineering requirements of the Naples Metro Line 1 (Italy) called for a thorough rethinking of the design process so that the engineering could be kept aligned with the architecture, integrating seamlessly the two with the construction methods, standards and technology.The preliminary design process consisted of three major phases: •,geotechnical and geological issues, preselection of construction methods; •,functional scenario based on engineering and construction requirements; •,review and merging of the architectural concept with the functional and engineering aspects. The last phase proved the most demanding one, matching the first outline sketches with the applicable construction methods. This required continuous alignment of approaches, eventually leading to the design consistent with the original architectural vision, yet fully compliant with the engineering and construction framework. At the beginning general information on Line 1 will be provided, followed by some main features of the construction work along the Dante – Garibaldi section both for the tunnel and the stations. At the end, the selected methodology and the related consequences on the functional, technical and architectural design will be outlined.City of Naples current municipal transportation plan envisages a circle ring line for the metro line M1. Actually it’s open to public the segment Piscinola – Dante – Garibaldi run by AMM, municipal company. This ring segment has been built by Metropolitana di Napoli, while Napoli Metro Engineering (company belonging to MMspa Group) is in charge for the planning of entire system and construction management. Line 1 connects Piscinola-Secondigliano northern periphery to Vomero shopping neighborhood, downtown and Central Railway Station."

Jan 1, 2016

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016