Search Documents

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By Bai-ru Xia, Cang-qin Jia, Qi-wu Huang

Limit Analysis Theorems has revealed to be a powerful tool for the development of numerical models aiming the determination of the load bearing capacity of structures reached by plastic collapse. This work presents a numerical formulation for the computation of strict upper bounds of the collapse loads of rigid-perfectly plastic mechanical systems, derived within the kinematical theorem framework. A key advance of this present method is that the problem is described only in terms of nodes and discontinuities connecting those nodes rather than element or bodies. The alternative approximation procedure to the traditional finite element method might involve discretization of a given body using a suitably large number of nodes laid out on a grid, with the failure mechanism comprising the most critical subset of potential discontinuities interconnecting these nodes. Potential discontinuities which interlink nodes laid out across the problem domain are permitted to crossover one another, giving a much wider search space than when such discontinuities are located only at the edges of finite elements of fixed topology. Highly efficient interior point method solvers can be employed when certain popular failure criteria are specified (e.g. Mohr-Coulomb). By adopting this processing approach it is possible to solve very large problems which normally exceed the memory capacities of a single computer. The developed numerical tool reveals to be robust and versatile, able to solve a wide range of 2D problems. Velocity singularities are automatically identified and visual interpretation of the output is straightforward. Several numerical examples including rock slope are studied by the new method, and the results are very close to those calculated by using analytical method and FEM.

Jan 1, 2015

By K. N. Han, H. C. Cho, R. Kim

"A comprehensive analysis of the effect of OH- on various cations in hydrometallurgical systems has been investigated. Cations chosen for this analysis included groups 1A and 2A, rare-earth elements and other common transition metal ions such as Cu2+, Fe2+, Fe3+, Mn2+, Ni2+, Co2+, Ag+, Cd2+, U4+, UO2 2+, Hg2+, Al3+ and Zn2+. The Newton-Raphson technique was used to calculate and plot various metal species over a wide range of pH. This study has clearly shown that by adjusting the concentration of OH-, the separation of Fe from Mn, U from V, Ce and Eu from other rare-earth elements, and In from Sn is possible. The effects of hydrated metal ions on the separation and removal of various metals from each other under various conditions is discussed.IntroductionThe primary purpose of hydrometallurgical processing is to extract, remove and purify various metals from diverse sources. Hydrometallurgists are frequently preoccupied by the extraction of cations in metallic form, but overlook the important role anions play in such processes. A proper choice of anions can determine the fate of successful extraction, removal and purification of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2005; Al-Tarazi et al., 2004), and also separation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974) of cations from various solutions.In this study, the authors have examined some of the effects that anions play in various solutions. The anion considered in this study was the first hydroxide, OH-. Other anions, such as Cl-, Br-, I-, and CN-, will be dealt with in the second part of the series of two papers."

Jan 1, 2015

"Foreword by Emily SarverAssistant professor, Mining and Minerals Engineering, Virginia Tech, Blacksburg, VAThe Mineral Processing Division hosted its fifth Student Poster Contest during the 2014 SME Annual Meeting and Exhibit in Salt Lake City, UT – and, by all accounts, it was a huge success! This year, the contest more than doubled in numbers of individual entries and schools represented. A total of 30 students participated, including 23 graduates and 7 undergraduates, representing 13 US and international institutions: Colorado School of Mines, Michigan Tech, Missouri University of Science and Technology, Montana Tech, New Mexico Tech, South Dakota School of Mines, University of Kentucky, University of Utah, Virginia Tech, West Virginia University, Autonomous University of Chihuahua (Mexico), UNAL Medellin (Colombia), University of British Columbia (Canada). In addition to constructing their posters, students submitted abstracts and gave short oral presentations highlighting their research. Based on tallied scores from all three components of the contest, the judging panel selected 1st, 2nd and 3rd place winners at the undergraduate and graduate levels, which were announced during the MPD Luncheon on February 26.In the undergraduate division, University of Utah’s Lucas Pich was awarded the 1st place prize for his poster “Solid-liquid mixing studies in lab-scale flotation tank using electrical resistance tomography.” His extended abstract is included in this issue of Minerals & Metallurgical Processing. Joshua Chidester, also of Utah, won 2nd place for his poster presenting “Evaluation of detectors for radiotracer RTD measurement by MCNP.” And Lucas Rojas-Mendoza, of UNAL Medellin, took 3rd place for his poster on “Preg-robbing in Colombian gold ores.”In the graduate division, 1st place went to Caelen Anderson, of the Colorado School of Mines, who also placed in this contest in 2012 and 2013! The 2nd and 3rd place prizes were awarded to Jacob McDonald and Joseph Halt, respectively, both of Michigan Tech. Extended abstracts describing the work of these up-and-coming researchers are also included in this issue.The 2014 Contest was chaired by Emily Sarver (Virginia Tech) and Lisa Schlink (Freeport-McMoran Copper and Gold, Inc.). Aaron Noble (West Virginia University), David Perkins (Derrick Corporation) and Derek Novotny (Eriez) graciously served on the judging panel this year.Special thanks are extended to all sponsors of the 2014 MPD Student Poster Contest, and to all student participants. Please watch for upcoming details on the 2015 Contest. We look forward to seeing you in Denver!"

Jan 1, 2015

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By Eduardo Lozano, Vilem Petr

The use of explosives bring countless benefits to our everyday lives in areas such as mining, oil and gas exploration, demolition or avalanche control. However, because of the potential destructive power of explosives, strict safety procedures must be an integral part of any explosives operation. The goal of this paper is to provide a solution against the hazards which unfortunately accompany the use of explosives. For this reason, a blast shield is specifically designed and tested for protecting personnel against these unpredictable effects. This document will develop a complete analysis answering the following questions: what are the potential hazards from an air blast; what are their effects; and how can we be protected against them. In order to answer these questions, theoretical, analytical, and numerical calculations are performed. Finally, a full blast shield prototype is tested under blasting conditions proving its effectiveness as a safety device while explosives are used.

Jan 1, 2015

By É. Roberge, S. Makni, G. Gagnon, F. Lavoie, A. Faucher

"Feed particle size is an important variable for the primary grinding mill operation. Several commercial vision systems have proven to successfully measure online many types of ores and are used for automatic control. However, due to limitations associated with segmentation algorithms, these systems fail to provide good measurements when the feed is composed of a specific bimodal particle size distribution: very big rocks and a large amount of fine particles. This is typically the case for crushed iron ore. This paper presents a technique to overcome the limitations of existing vision systems by using 3D cameras and appropriate processing methods. It provides online particle size distribution indicators and bulk volume flow rate measurement. It is designed to be very cost-effective, robust, precise, easy to install and to maintain. The 3D system was validated in two iron ore processing plants and the results clearly show that it can be used to optimize primary grinding mill operation where 2D segmentation vision systems fail.INTRODUCTIONFragmentation measurement using digital image processing has successfully been applied in mining and mineral processing operations. Several maintenance and operating applications are already deployed in the industry: Measurement of rock fragmentation after blasting (Maerz, 1999; Palangio, 1999) (Pragyan, 2012) Truck inventory (Palangio, 2005) Monitoring of crusher mantle wear Automatic control of crushers and SAG mills (Bouajila, 2000) (Bartolacci, 2001)Commercial technologies like WipFrag (Maerz, 1999), VisioRock and others proved to be very efficient to precisely measure the particle size distribution of many types of materials. These products are mainly composed of a camera, a lighting system and an image processing system based on a segmentation algorithm. By controlling adequately the lighting conditions and with periodic maintenance on the segmentation algorithm calibration parameters, it is almost always possible to achieve reliable measurements.However, the segmentation algorithm is not adequate when the particle size distribution contains big rocks and a large amount of fine particles. In this case, the area containing the fine particles is accounted as a big rock while big rocks get segmented as multiple smaller sized particles, leading globally to a wrong measurement. This situation prevails for crushed iron ore and coke, among other materials. Figure 1 shows a picture of a material which is typically very difficult to process through segmentation techniques."

Jan 1, 2015

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By G. B. Harris, C. W. White

A study to investigate the recovery of base metals, notably copper, nickel, cobalt, zinc and manganese from iron-free concentrated chloride solutions using ion exchange was undertaken. In such solutions, apart from nickel and, to a lesser extent manganese, these metals are present predominantly as complex anions, and therefore conventional separation techniques based on cationic resins are not applicable. The results demonstrated that zinc, copper and cobalt can all be separately recovered leaving nickel and manganese behind. Specifically, zinc is a major nuisance element in nickel and cobalt processing, and the testwork showed that it can be preferentially removed prior to copper and cobalt. Selective resins for both copper and cobalt were identified, and it was demonstrated that the strength of the chloride background matrix has a significant effect on the efficiency of separation. An additional major advantage in such systems is that stripping can mostly be effected with water. Finally, some observations are made on the hurdles that must be overcome when attempting to introduce and commercialise new technologies.

Jan 1, 2015

By P. Conrad, S. Rosenthal

"Engineers remain in demand. Job opportunities in the United States still exceed the number of students graduating from college with degrees in Mining Engineering. Although enrollment is up for freshman studying Mining Engineering, many of those students will either change majors or not complete their degree, maintaining that deficit of available Mining Engineers. What can be done to ensure that enough Mining Engineers will graduate to fill the needs of the mining industry over the next ten to 20 years? The authors believe that this need can be met by recruiting students to Mining Engineering programs who are genuinely interested in working in the mining industry. With this in mind, Montana Tech conducted its first Mining Engineering camp in July 2014 to get junior and senior high school students interested in careers in the mining industry by showing them that Mining Engineering is both an exciting and rewarding career. This paper discusses What a Blast! The 2014 Montana Tech Mining Camp. INTRODUCTION The concept of summer camps for high school students is not new. For example, Missouri University of Science and Technology has offered their “Explosives Camp” for several years. A large percentage of attendees to these camps discover or confirm an interest in Mining Engineering and enroll in the school’s program. The Dean of the Montana Tech School of Mines and Engineering challenged department heads to develop and offer summer camps for prospective high school students to get a taste of engineering with the goal being to improve recruitment for each discipline. Mining Engineering embarked on the concept of a summer camp in 2013 with a concept to provide a week’s experience in Mining Engineering during the summer of 2014. What it takes to progress from concept to reality, with some of the learnings to be shared, follows."

Jan 1, 2015

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By S. Hume, J. Shepherd

Meso-2,3-dimercaptosuccinic acid(DMSA) was studied as an additive for thiosulfate leaching of gold. DMSA was added to solutionscomposed of either sodium thiosulfate or calcium thiosulfate and the solutions were tested for their ability to leach pure gold samples as well as a calcined gold ore from Barrick Gold Corp. Results showed prolonged leaching of pure gold samples when DMSA was added at a concentration of 5µM; however, higher concentrations were shown to inhibit leaching. Differential capacitance measurements of the interface indicated that DMSA adsorbed as a defective monolayer on the surface of gold at low concentrations and formed a more compact monolayer with increased concentration. It is proposed that a concentration of 5µM DMSA produces a defectivemonolayer on the surface that still allowsthe transport of oxidants to the underling metal while inhibiting the formation of polysulfide passive layers that arise fromdecomposed thiosulfate.The 5µM DMSA/CaS2O3 system was also studied using calcined ore. Results showed that the initial leaching rates in the presence of DMSA are lower than those obtained in thiosulfate alone. However, after 10h, prolonged leaching is again observed when DMSA is included.

Jan 1, 2015

By Wilson Pascheto

One of the main outcomes of a capital project is the reliability of a new plant, system or equipment. During 20 years of experience working in various capital projects for the mining industry, the author experienced failures which have caused significant losses to Owners, in many cases amounting to millions of dollars and almost jeopardizing entire projects. Often, failures were related to faulty design, shop fabrication and/or construction. Therefore, significant opportunities exist in the Mining Industry to improve the success rate of capital projects, improve on-line time at start-up, minimize the occurrence of unplanned maintenance due to equipment failures, and all this with positive contribution to health and safety. This paper presents some examples of failures and how they could have been prevented by proper Quality Assurance methodology. It also discusses some of the main challenges in the implementation of such methodology, including awareness of the Materials discipline and availability of trained Engineers.

Jan 1, 2015

By O. A. Ojo, E. Anisimov, A. K. Khan

Electro-spark deposition (ESD) has recently generated a great deal of interest in processing aerospace materials. This is due to its potential for joining and repairing difficult-to-weld precipitation strengthened nickel-based superalloys without having problems of welding cracking that often plaque these materials. The short duration of current pulses involved in the process combined with the intermittent contact results in extremely rapid thermal cycle that produces nearly no heat affected zone in the substrate material. The microstructure of electro-spark deposited superalloy was meticulously studied in this work by scanning electron microscopy (SEM) and analytical transmission electron microscopy (TEM). The results show that in contrast to general assumption, the extreme rapid cooling rates involved in the ESD process did not produce partition-less solidification that is devoid of second phase microconstituents in the material. The secondary microconstituents were found formed along the intercellular regions of the solidification microstructure. The nature of these particles and the possible implication of their formation on mechanical properties of ESD processed material are reported and discussed.

Jan 1, 2015

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015

By J. Zachwieja

As part of a general review on study of surfactant blinding agents to improve gold recovery during cyanide leaching of carbonaceous gold ores, processes of CIL and RIL leaching using surfactants were investigated. When refractory ores were treated by surfactants, CIL and RIL leaching processes yielded significant improvement on gold recovery. This paper will discuss and compare the laboratory results from two different leaching processes on preg-robbing ores, as well as, illustrate the difference of potential fouling of the blinding agents on activated carbon and resins.

Jan 1, 2015