Search Documents

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Holtham, J Meng, E Tabosa, W Xie

Turbulence and its distribution are of great importance in flotation, and have received considerable attention recently. However, there is no mature technique to measure turbulence in three-phase (liquid-solid-gas) industrial flotation cells due to the opaque, highly aggressive and abrasive nature of the slurry involved. Previous research has shown that the piezoelectric vibration sensor (PVS) is a promising tool for turbulence measurement in industrial flotation cells. The PVS is a robust device that converts mechanical vibration to electrical signal, from which turbulence information can be extracted. An improved calibration method has allowed development of a frequency model to calculate the force applied to the sensor. Experimental results and comparison with laser doppler anemometry (LDA) have shown that the PVS can measure fluid kinetic energy, which is related to turbulent kinetic energy, a parameter used in the literature to represent turbulence in flotation. Laboratory measurement in a two-phase (water and air) 60 L cell and with slurry in a 3.5 L cell gave good stable results and mostly consistent trends between the measured turbulence profile and cell operation. When applied in a 300 m3 industrial cell filled with water, the addition of air or slurry to the cell resulted in a shift in the turbulence profile. This is expected because a change in fluid density will change the force applied to the sensor. It is therefore concluded that the piezoelectric sensor is an easy-to-use and robust technique that is fully capable of measuring turbulence in industrial flotation environments.CITATION:Meng, J, Tabosa, E, Xie, W, Runge, K C and Holtham, P, 2014. Development and application of a piezoelectric sensor for turbulence measurement in industrial flotation cells, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 457–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S. Kim Juniper

"This presentation aims to serve as a primer on conservation, research and regulatory organizations interested in the environmental impact of deep-sea mining. It will also consider a recent, early-stage proposal for an experimental SMS mining operation aimed at increasing our understanding of mining impacts and ecosystem recovery.Over the past 5 years, as deep-sea mining has been moving closer to reality, it has attracted growing attention from deep-sea biologists, conservation groups and operators of deep-sea research vehicles and observing systems. Several new international research organizations have emerged that have a direct interest in deep-sea biodiversity conservation, and the environmental impact of ocean mining. These include INDEEP, which evolved from the 10-year Census of Marine Life program, the Deep Ocean Stewardship Initiative that has recently hosted several high profile international meetings, and the VentBase forum of academics, industry and regulators that aims to develop environmental best practices and informational documents for all stakeholders involved in Seafloor Massive Sulphide (SMS) mining. InterRidge, currently hosted by China, represents a decades old partnership of deep-sea biologists and economic geologists who discovered the more than 100 known hydrothermal vent fields and SMS deposits on midocean ridges and in other settings of seafloor volcanism. In 2012 InterRidge formed an industry liaison group to examine how the mid-ocean ridge researcher community could contribute to the development of environmentally responsible practices for the exploration and exploitation of SMS deposits. While initial meetings with industry were promising, InterRidge members are currently debating the relative merits of sharing exploration know-how and understanding of vent ecosystems with industry, against the need to maintain their independence as stewards of deep-sea ecosystems."

Sep 1, 2014

By R Araya, G Harbort, D R. Seaman, L Huynh, P D. Munro

In today’s operating environment many conventional cleaner circuits struggle to produce final grade concentrate with acceptable levels of non-sulfide gangue and/or penalty elements. This is primarily due to poor selectivity and the entrainment of gangue, and is further exacerbated by the processing of lower grade ores with more complex mineralogy that require finer grinding for liberation. In new concentrators, the standard approach to cleaner circuit design is to define the number of stages of mechanical cells required to achieve the desired concentrate grade. Residence time is the primary factor to size cells and to determine the number of cells required to attain target recovery. While it is required for recovery, a bank of mechanical cells is not the ideal solution to maximise concentrate grade. Relatively coarse bubble size means slow flotation of fines, requiring long residence times. The combination of long residence times and no froth washing means higher entrainment as the pulp becomes more barren and froth stability decreases down a bank.In recent years, the Jameson Cell technology has been retrofitted into a number of concentrators around the world to solve both cleaner circuit capacity and concentrate grade issues. Jameson Cells have been installed at the head of conventional cleaner circuits to produce final grade concentrate in a single step of flotation using a single cell (referred to here as ‘cleaner scalping’ duty). The experience gained from these installations has provided the platform for the design of improved and simpler cleaner circuits that will perform better and be more robust to operate. This paper analyses traditional cleaner circuit designs and explains the philosophy behind new hybrid cleaner circuits, which use Jameson Cells to produce final concentrate and mechanical cells for a ‘cleaner scavenger’ duty. The advantages of the new cleaner circuit design are demonstrated by a case study from an operating plant. Engineering studies show that the better metallurgical performance can be achieved with less equipment than conventional cleaning designs, reducing capital cost, operating cost, and with more than 30 per cent energy savings.Finally, the paper describes simple modifications to the standard laboratory flotation test procedures which accurately simulate this new cleaner circuit using routine equipment.CITATION:Huynh, L, Araya, R, Seaman, D R, Harbort, G and Munro, P D, 2014. Improved cleaner circuit design for better performance using the Jameson Cell, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By T J. Napier-Munn

This paper proceeds from the premise that process improvement is a key part of the mineral engineer’s role, and one in which he/she can make a significant contribution to shareholder value. It presents four tools to help with process improvement projects. Two are designed for process monitoring, to determine as soon as possible whether there has been a true change in performance: the cumulative sum (cusum) control chart plot with V-mask, and the control chart using a process model. The other two are used for process optimisation: simplex self-directing evolutionary operation (SSDEVOP), and a response surface model developed using a central composite rotatable experimental design (CCRD). These methods are robust, have a rigorous theoretical basis and are easy to implement. They also promote project continuity which increases the chances of success, particularly in fly-in/fly-out (FIFO) operations. Variants are used in other industries, but they are rarely if ever applied in mineral processing to-day for reasons which are unclear. The paper gives examples of the application of each method in concentrators which demonstrate that they have the potential to be useful additions to the mineral engineer’s professional toolbox.CITATION:Napier-Munn, T J, 2014. Cunning solutions to process improvement, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 5–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Shuen, R Sales, D La Rosa

Semi-autogenous grinding (SAG) mill control is complex and depends on many dynamic process variables. Good control strategies ensure that a mill is operating as close to optimal as possible, resulting in significant economic benefits to an operation. Pueblo Viejo, a gold mine in the Dominican Republic, has been actively improving their control strategies since start-up in 2012, and one of these initiatives was to install an acoustic monitoring system on the SAG mill. The data from the system is used to optimise the mill’s performance by limiting the time the mill is either running too quiet or too loud. The lower limit is an indication that the charge in the mill is too high for efficient breakage or that the mill speed is too low and grinding media are not striking the toe of the charge. Conversely, when the acoustic emissions from the mill are too high, this can indicate that the balls are striking above the toe of the charge, resulting in inefficient grinding and excessive liner and lifter wear. Adjusting mill operating conditions to keep acoustic emissions in the ‘sweet spot’ between these limits results in more efficient grinding.Pueblo Viejo installed a Metso SmartEar™ to monitor the acoustic emissions of their SAG mill in January 2013. This system has been installed on many mills around the world and is specifically designed for optimising SAG mill control. One system output is the impact counter which measures steel-on-steel impacts on the mill shell. The impact counter uses both frequency and time domain analysis to approximate the number of ball impacts per minute. This method of analysis excludes parts of the sound signal not associated with steel-on-steel impacts and gives an accurate measure of this critical control parameter. After the acoustic system was installed, Pueblo Viejo collected data to determine the upper and lower limits for the impact count variable. The live data is available to the mill operators and it is used as one of the key operating variables to control the mill.Through continuous improvement and the use of advanced technologies like SmartEar™, Pueblo Viejo are improving the control and operation of their SAG mill, resulting in reduced liner wear, more efficient mill performance and optimised energy consumption. This paper discusses the installation of the system, and the measureable benefits obtained by using acoustic monitoring to control their SAG mill.CITATION:Shuen, D, Sales, R, Wortley, M and La Rosa, D, 2014. The benefits of using SmartEar™at Pueblo Viejo, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Diane Jones, Jeremy Spearman, Tom Matthewson

Requirements for minerals are on the increase globally and the deep sea offers a potential source of essential materials. Extracting these minerals from what is considered an environmentally sensitive area, and one about which little is still known, is a challenging activity, which needs careful consideration and an appropriate environmental impact assessment to be carried out. Extraction of material from the deep sea beds can cause disturbance or damage to benthic communities; impact on mobile marine species such as fish, mammals and reptiles; cause increases in suspended sediment and sediment deposition onto potentially sensitive areas or potentially release contaminants which were previously bound to the sediment. This paper discusses the potential environmental issues surrounding extraction of deep-sea deposits using aggregate dredging techniques and how those issues can be appropriately assessed. In particular issues of suspended sediments, plume transport, water and sediment quality and underwater noise impacts on potentially sensitive species and habitats will be explored.

Sep 1, 2014

By M Zanin, E Chan, D Xu

An experimental design has been developed to investigate the relative influence of distinct pulp and environmental properties on froth stability in the flotation of a typical porphyry copper ore. In particular, factors such as frother and collector type, feed particle size (P80), solids per cent, composition (chalcopyrite and pyrite content), as well as grinding environment (mild steel versus stainless steel, high and low pH) have been varied in a controlled manner, and the resulting froth stability evaluated. A previously developed froth stability column, based on the Bikerman approach, was used to measure the froth height and half-life in each test. The relative effect of each factor is presented here on a comparative basis. It is shown that frother type is the most important factor, with marked difference in froth stability when switching from methyl isobutyl carbinol (MIBC) to glycol based frothers. Solids per cent and particle size also play a significant role. The grinding environment had lesser effect on the resulting froth stability, although mild steel grinding gave higher froth stability compared to stainless steel grinding. The experimental evidence supports the hypothesis that in porphyry copper flotation the grinding environment influences surfaces oxidation, pyrite activation and the extent of hydrophobic particles reporting to the froth phase. This has an indirect effect on the resulting froth stability, which is however small if compared to the other factors. This work is still in progress, and extension to other mineral systems is planned. However, some insights are offered to operators on the parameters which are more likely to have an impact on froth stability in copper flotation plants.CITATION:Zanin, M, Chan, E and Xu, D, 2014. Empirical evaluation of factors affecting froth stability in copper flotation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Costa, L Polizzi

Process optimisation and continuous improvement are usually acknowledged when making a process more effective, efficient and transparent. During the last few decades, thousands of companies around the world have used total quality concepts in order to establish a continuous improvement process in their companies. Typically these companies apply some kind of Kaizen-type tools and expect results in the short term; however, the great majority of companies are poorly implementing these continuous improvement programs.Usually the most common reasons for failure of the program are lack of commitment from leaders, lack of discipline and engagement from the team to follow process and lack of clear targets for the program. When the results do not come at the expected timeline, it is common to simply drop the current process and apply a different approach from another company or consulting firm.This paper will explore some successful cases of companies that have invested time and effort to establish a reliable and sustainable process of continuous improvement. The focus will be case studies of mines and smelters around the world that use the plan–do–check–act (PDCA) cycle to increase productivity with the best services and lowest costs. The main tools and processes used by these companies will be discussed, as well as results achieved.CITATION:Costa, M and Polizzi, L, 2014. Introducing and sustaining a continuous improvement program in mines and smelters, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L Kormos, V Lawson, G Hill, G Marrs

"In sulfide nickel deposits throughout the world, pentlandite and pyrrhotite are commonly found together along with varying amounts of chalcopyrite and platinum group minerals (PGMs). The mafic or ultramafic host silicates associated with the sulfide mineralisation commonly exhibit a complex assemblage of magnesium bearing silicates, many of which themselves contain significant nickel. Four types of ore are proposed, each presenting their own processing challenges. These are: economic grades of Ni, Cu and PGE (platinum group element) in a pyrrhotite-bearing sulfide deposit, with low pyrrhotite to pentlandite ratios  economic grades of Ni, Cu and PGE in a pyrrhotite-bearing sulfide deposit, with moderate to high pyrrhotite to pentlandite ratios uneconomic high pyrrhotite: low tenor deposits low-grade low sulfide, high MgO ± PGE deposits that can sometimes be economically mined and processed.The grades and recoveries of nickel concentrates produced from sulfide ores can be significantly impacted by the ore mineral texture, the nickel tenor of the sulfides, and the polytype of pyrrhotite which may be either hexagonal (non-magnetic) or monoclinic (magnetic). The mineralogy of the silicates is also of great importance, especially the magnesium silicates and those which tend to produce particles which are asbestiform or which affect slurry viscosity. Other magnesium silicates such as serpentine carry nickel in solid solution, limiting the recovery entitlement of nickel by flotation because serpentine is not amenable to sulfide flotation mechanisms. Differences in plant flow sheets and reagent assemblages are required to effectively separate these minerals.Experience from a variety of plant operations and from extensive flow sheet development programs are discussed. Examples are given of where significant improvements in nickel circuit performance can be made by adjusting plant physical processing conditions or process chemistry to compensate for measurable ore properties and characteristics.CITATION:Lawson, V, Hill, G, Kormos, L and Marrs, G, 2014. The separation of pentlandite from chalcopyrite, pyrrhotite and gangue in nickel projects throughout the world, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Jeff Ardron

Unlike the first predicted deep-sea mining (DSM) boom 35 years, the public response to the re-emergent possibility of DSM is this time round is not entirely optimistic, with serious economic, social, and environmental concerns being voiced. In the intervening years, the troubling notion of the ‘resource curse’ has been popularized, whereby the economies of developing nations rich in natural resources (agriculture, minerals, and fuels), paradoxically appear to fare more poorly than their brethren who have fewer such resources. There have been a variety of explanations and counter-arguments regarding why the resource curse occurs, including how it can be ‘escaped’, and even some disagreement on whether it in fact does occur. Nevertheless, many commentators appear to agree that that the quality of governance is strongly implicated in the socioeconomic success, or failure, of these resource-dependent nations, and could indeed be the deciding factor. Unlike nations with diversified economies, the majority of the income from natural resource economies, in the form of royalties and rents, flows through national government; hence, good governance and fiscal management is of particular concern.

Sep 1, 2014

By M Davies, G Theletsane, A H. Gray

Recovery of gold from gold ores has been driven by the available technology and its configuration in the process plant flow sheet.Conventional practice in test work programs has the ore being ground fine (to 106 or 75 microns) to ensure liberation ahead of leaching or flotation. This paper identifies that, in many cases, gold and gold sulfide carriers will liberate and be recovered to a concentrate at much coarser sizes.There is an exponential increase in energy consumption relative to particle size reduction. This impact becomes extreme when comparing crushing a product to 1 mm against grinding to 75?microns.The resultant reduction in energy consumption when liberating and separating at 1 mm or coarser compared to grinding to 75 microns can be in the order of 15 kWh/t or 60 per cent of energy in the comminution circuit.Recovery of free gold and gold sulfide carriers by preconcentration (using continuous gravity devices such as the InLine Pressure Jig), combined with flotation of the fine gold and gold carriers, can result in significant power savings.There are multiple locations within the flow sheet that can be targeted using this process, including recovery in the cyclone underflow of existing plants, preconcentration ahead of the plant or complete greenfield, low-energy process plants designed from first principles based on data from a Gekko developed test work regime.We will describe the process of defining mineralogy in the laboratory and the decision-making process through to actual applications in the field.Several examples will be provided, including a South African Witwatersrand gold ore, several Australian gold ores and others, indicating the benefits of this process and where it has been brought to commercial reality.CITATION:Gray, A H, Davies, M and Theletsane, G, 2014. Coarse liberation and recovery of free gold and gold sulfide carriers for energy reduction in process plants, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 117–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By G du Toit, P L. Gillot, M Swanepoel

Randgold Resources’ Loulo-Gounkoto Complex is one of the largest gold mining operations in Mali, West Africa. The mine, which is situated on the western border with Senegal, treats more than 4 Mt/a of ore through a conventional three-stage crushing and ball milling circuit followed by a carbon-in-leach plant. Ore supply is achieved by a combination of open pit and underground mining, with the majority of the ore supply sourced from the Gara and Yalea underground mines situated approximately 2 km and 6 km respectively from the gold plant.In 2011, Randgold Resources commissioned Golder Associates to perform an evaluation study for providing structural backfill to both the Gara and Yalea underground mines using the current gold plant tailings. The test work performed as part of the evaluation study concluded the need for a tailings cycloning and dewatering facility capable of producing slurry at a solids concentration of 65 per cent with a particle size distribution that had minimum 25 per cent passing 20 µm and less than 5 per cent of -5 µm material. Tailings desliming was required to ensure a consistent feed quality to the paste preparation plants and to ensure that the system would be capable of handling variation in the feed composition from the gold plant.WorleyParsons, previously TWP Projects, was contracted by Randgold Resources to complete the engineering design for the slurry preparation plant, whilst Golder Associates was retained to complete the engineering design of the two paste preparation plants.This paper discusses the test work, design considerations and engineering design of the slurry preparation plant, termed the ‘intermediate plant’, as well as all ancillary facilities required for the delivery of the deslimed slurry to the paste preparation plants located at the two underground mines.CITATION:Swanepoel, M, du Toit, G and Gillot, P L, 2014. Case study – engineering design for a slurry preparation plant for a paste application in West Africa, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 477–486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By A Cranley, A Giblett, S Thacker

The Newmont Tanami Operations are located in the Northern Territory, approximately 550 km north-west of Alice Springs. The Granites process plant commenced operations in 1986 as a 300?000 t/a ball mill / carbon-in-leach (CIL) plant and has undergone numerous expansions between that time and the current day, with project-to-date gold production exceeding 6.5 Moz. Annual plant throughput has exceeded 2.8 Mt/a while processing a blend of open pit material and ore from the Callie Deeps underground mine, with annual gold production exceeding 400 koz. In 2013 the operation processed 1.8 Mt of underground ore for the production of 323 koz of gold.This paper reviews the operation and expansion of The Granites process plant since the mid to late 1980s with particular focus on the gravity gold recovery circuit. The Tanami ores contain significant levels of free gold, and gravity recovery has long been an integral component of the metal recovery process at the Granites plant. The results of ten years of gravity circuit performance analysis and optimisation are presented.CITATION:Giblett, A, Cranley, A and Thacker, S, 2014. Three decades of gold production at the Newmont Tanami operations, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 209–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Thompson, D Rose, S Yu, W Baum, R Zahn, D Meadows, G Hall

Opportunities to improve mill operations are often cited by mining companies and recognised in many concentrators spread throughout the world but are not always followed through. Copper-molybdenum concentrator operations are challenged by a continuously increasing list of detrimental factors. They include deteriorating ore characteristics and poor mineralogical information on deeper ores, water quality and availability, steel wear and increasing power costs. Rapidly declining productivity, sustainability and environmental factors, new taxes, mining industry global skill set shortages, to name but a few, must also be considered. The days of maximising value by just increasing production or simple cost cutting are fading and will not be sufficient for the future of more complex mineral processing operations and larger plants. As a result, FLSmidth’s Global Process Technology Group has launched a plant and process optimisation program based on mineralogical and metallurgical surveys.Copper-molybdenum concentrators of the future need a paradigm shift. Modelling and simulation tools alone are not the answer to complex mineralogical associations and larger scale equipment and operations. Detailed area by area review aimed at identifying process constraints in terms of equipment and operating practice in conjunction with robust diagnostic work, ie mineralogical and metallurgical characterisation, are mandatory for process optimisation. The navigational beacon, for all operations who want to remain competitive, will be ‘process efficiency’. Since the use of automated mineral analysers has become more readily available and reliable, mineralogical-metallurgical plant surveys have proven themselves as the most efficient tool for optimising plant performance.The following paper will illustrate how operations can move toward eliminating under-performing flow sheets, fixing run-away flotation conditions, maximising individual process equipment performance, preventing shortcuts in Bond work index testing which may cause the failure of comminution models and minimising costly and time-consuming ‘debottlenecking’. As previous plant surveys have shown, the net project cash flow can be increased by 50 to 200 per cent if a combination of robust ore characterisation and plant process mineralogy is performed. The combined plant survey approach has been demonstrated successfully in a multitude of operations. This includes the use of key ore types in concert with statistically sampled process streams, bench-scale metallurgical tests and automated mineral analysis on a size-by-size basis.CITATION:Meadows, D, Hall, G, Rose, D, Thompson, P, Baum, W, Zahn, R and Yu, S, 2014. Copper-molybdenum concentrator surveys using mineralogy and process benchmarking tools to improve overall plant performance, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 315–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M M. Hilden, M S. Powell, B Foggiatto

In an environment of decreasing ore grade, increasing costs and uncertainty with respect to commodity prices, the industry could benefit from evaluating alternative technologies and innovative circuit configurations. The flexible circuit approach suggests that the design of grinding circuits can be adapted to changes in feed properties and economic conditions. Advances in modelling and simulation are enabling metallurgists to predict the performance of more complex circuit configurations with increased confidence. Ore variability information and processing costs may be used as modelling inputs to determine the optimum processing conditions at a given time. A case study has been completed demonstrating the value of combining a flexible circuit with a model-based optimisation of the process. Ore properties and equipment performance data obtained in operating plants have been used to model and simulate flexible circuit configurations.This paper explores strategies to introduce flexibility to existing circuit configurations when processing ores with high variability. Multicomponent models incorporated in the model developers’ kit (MDK) allow the simulation of more complex and flexible circuits. This capability enables demonstration of the potential to enhance metal production through adapting processing routes according to the ore type being processed. The simulation of different flow sheet configurations allowed the definition of the best option for maintaining the metal production when treating lower grade ores, highlighting the advantages of flexible circuit configurations compared with a one-process-fits-all approach.CITATION:Foggiatto, B, Hilden, M M and Powell, M S, 2014. Advances in the simulation of flexible circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 391–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Hartog, V Beehan, D Beeson

Treating an ore blend from five different deposits at Newgold’s Peak Gold Mine (PGM) has always been a challenge due to the inherent variability between each of the orebodies.Operating the processing plant at PGM with a ‘normal’ level of process control and a good operations and metallurgical team has allowed the processing plant to achieve above the name plate design at 102 t/h and recoveries in the order of 92.8 per cent for gold and 88.4 per cent for copper.With a company value and culture of striving for continuous improvement, PGM implemented the Manta Cube® system, an advanced process control system, for the semi-autogenous grinding (SAG) mill, gold leach circuit and tailings thickener over a 12-month period throughout 2012 and 2013.The overall benefits of implementing the Manta Cube® system has led to an increase in mill throughput of at least two per cent, improved SAG mill liner life, a ten per cent decrease in cyanide consumption and a reduction in flocculant of at least 30 per cent with no detriment to the gold and copper recoveries.The entire project had a payback period of less than two months, and the combined benefits resulted in an overall increase in revenue of at least $5 million per annum. This is quite significant for a processing plant the size of PGM.This paper describes the methodology, overall results and economic benefit of applying the Manta Cube® system on-site at Newgold’s PGM.CITATION:Hartog, J, Beehan, V, Karageorgos, J and Beeson, D, 2014. Optimisation of the Peak Gold Mine’s processing plant through advanced process control, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014