Search Documents

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By J. H. Starkey

SAGDesignTM Testing for grinding mill design was introduced commercially in 2004. Up to January 2008, 18 projects have been completed and 99 samples have been tested using this method. Two papers have been published describing the patented test procedure and one of these shows how the results compare with other grinding test methods. This paper will briefly discuss the theory on which this technology is based, and explain the procedures used to develop the calibration equation. Case studies are also included to demonstrate the effectiveness of the test work being done. These case studies show how the SAGDesign test is being used today: to design new grinding circuits for commercial full scale use; to calculate throughput in existing mills for production planning; and to accurately define grinding mill requirements at the scoping, pre-feasibility or feasibility study stage of project development, in order to economically identify the size and cost of the grinding mills that will be needed for the project. This is important because if the full rec-ommended SAGDesign testing program is done at an early stage in the project, the definitive cost for a guaranteed throughput, grinding mill design (by Outotec if their mills are purchased) is available. New grinding mill design for final engineering will be represented by the test work done on the Climax Molybdenum Project for Phelps Dodge (now FMI) in Colorado, USA. The SAG mill and ball mill for Climax are now in fabrication with project start up in late 2009. Next, the sizing of grinding mills at the scoping, pre-feasibility or feasibility study stage of mine development will be represented by a large metal mining property in Russia. Finally, calculation of the throughput for existing mills will be represented by work done at a base metal mine, in eastern Canada. Test work for designing SAG mills is now done in four laboratories at the time this paper was written. One in the USA at Dawson Metallurgical Laboratories, Inc. in Salt Lake City, two in Russia at the TOMS Research and Design Institute and at the Irgiredmet Research Institute, both in Irkutsk, and a fourth mill has been installed in Australia at AMMTEC Limited?s lab in Perth. A fifth SAGDesign test mill for radioactive ores has been built by Starkey & Associates, specifically for testing uranium ores and can be moved to any licensed lab in the world on a project basis.

Jan 1, 2014

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery and product grade. Once the relationship between the production rate and cost is established, dynamic programming techniques can be used to define the optimum production schedule (that is, the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, assuming that the capacity and efficiency of the physical plant remain unchanged throughout the life of the deposit, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 2014

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

"WELCOME/BIENVENUE TO THE COM 2014 IN BEAUTIFUL VANCOUVER!On behalf of the organizing committee, I would like to extend my thanks to you for participating in this year’s Conference of Metallurgists. Recent times have been extremely difficult for the resource sector, but it is crucial for our industry to maintain personal connections through good and bad times. These interactions include technical exchanges, and this is at the heart of MetSoc’s service to its members. The theme of this 53rd Conference of Metallurgists is Prosperity Through Process Advancements. There are thirteen symposia at this year’s conference mainly focused on processing from extractive fields, to materials and the environment. Supporting these topics are the plenary, poster session, and trade show plus opportunities for socializing at functions like the opening reception and the awards banquet.Many people have contributed to this conference, from the authors and presenters to the organizers and the generous sponsors. They are all gratefully acknowledged for their quality work over the last two years. A particular thank you to our student volunteers whom we hope will take advantage of their time at COM to network and to learn about this exciting industry.Again, thank you for being a part of this exciting conference of metallurgists. I hope it will be a memorable experience and that you are able to take advantage of all the conference and Vancouver have to offer."

Jan 1, 2014

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Zheng Chen

"In this paper, solidification process of steel ingot was simulated by ProCAST software, based on cellular automaton-finite element (CAFE) model. A 22 t steel ingot was divided into continuous small zones (100x150x180 mm) in radial direction, then the temperature field, shrinkage cavity and porosity, particularly, the microstructure were simulated. The results show that: there was a columnar-to-equiaxed transition in microstructure on radial direction. Zones, closing to the center of the ingot, had a more developed and fined equiaxed zone, while zones closing to the periphery of the ingot had a more developed columnar zone. It indicated that temperature gradient has a great influence on microstructural morphology. Thus, the simulation results were highly agree with the experimental results, verifying the feasibility of this simulation method. It significantly reduces the time of simulation, and has important significance for predicting the microstructure of large steel ingot.IntroductionSolidification microstructure of steel ingot have a significant effect on the quality of the final steel products. Although many experimental works have been carried out in order to obtain the optimum condition for solidification process of continuous casting, it is also very desirable to establish mathematical models to simulate the evolution of solidification structure. The simulation methods can be divided into deterministic models and stochastic models, which have been developed rapidly over the last couple of decades. Cellular automaton method is one of the stochastic models. Rappaz and Gandin [1, 2], Nasatac and Stefanescu [3, 4] are the earliest researchers engaged in the this field. Moreover, Rappaz and Gandin simulated the solidification structure and CET (columnar grain to equiaxed grain transition) of metals using the CAFE method (cellular automaton-finite element method) for the first time [1, 2]. Recently, the CA (cellular automaton) model also considered the effects of fluid flow on the solidification process. Zhu, et al. [5-11] improved method of CA , they used the KGT model to describe the undercooling needed during the growth of the dendrite tip."

Jan 1, 2014

By W. J. Birch, R. Farnfield

Nuisance caused by perceived high vibration levels as a result of blasting on quarries and opencast coal mine is now the number one environmental concern of residents living adjacent to such operations. The intrinsic nature of blast vibration monitoring and prediction is that it is impossible to accurately forecast the vibration levels that will be experienced by a given blast at a given location. Thus it is that a statistical approach to the problem is the only viable option. Unfortunately, persuading local residents living adjacent to a project that requires blasting that this is the best way of safe guarding both their homes and their quality of life is not an easy task. Thus routine monitoring involving both operators and regulators play a key role in building trust. However, public confidence is often shaken when regulators and operators use two different blast monitoring instruments side by side to record a blast at a local resident’s house and arrive at different results. To make certain that this does not happen in future, what is needed is a protocol that ensures that any two different blasting seismographs give the same peak particle velocity values at the same observation point. To do this all the equipment manufacturers, regulators and relevant professional explosive engineering bodies need to be involved.

Jan 1, 2014

By N. J. Bolin

The Aitik copper mine is located in the north of Sweden and the concentrator at the mine started its operation in 1968 with a capacity of 2 Mton ore per year. Since then the operation has expanded several times, and today the capacity is 18 Mton ore per year. A new expansion plan was investigated in 2005, however the building of a new concentrator was found to be a better solution, giving a lower cost, a longer lifetime and more concentrates to the smelter at the coast. Several choices have been evaluated regarding the location of the concentrator?s crushing, grinding, dewatering, process control and water systems. The energy cost comparison has been an important factor when evaluating the various choices. The single most important decision has been in choosing the grinding system. Once again the fully autogenous grinding system, favoured by Boliden, has proven to be the best solution. The location of the mill, high and near the tailing pond, gives lower transportation costs for the ore and tailings, compared to other locations. A new water system will lower the pumping cost, give better control of water circulation to the plant and create fewer problems with permafrost in the tailings disposal area. Molybdenum recovery will be installed in the new plant using a separate circuit. A gold leaching plant was also investigated. Gold leaching is planned for the pyrite concentrate from the chalcopyrite/pyrite separation and the concentrate from the desulphurisation circuit that will be installed on the bulk flotation tailings.

Jan 1, 2014

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

By G. Demi

Chromium ore exploitation has commenced in 1948 in Albania and there are produced about 24.3 million tons up to the end of 2006. Last years the prices and need were increased notably. Main export of chromium ores and concentrates was accomplished respectively 114 500 ton and 13 000 ton in People Republic of China during 2006 year. Location, status, reserves and grade of chromium deposits of Albania are presented in the paper. Chromium ore enrichment is related with their composition and Cr2O3 content, as well as with market requests. Actually, high grade chromium ores with Cr2O3 content over 38% ~ 40% are directly exported or treated in metallurgy, but last time have been exported and chromium ores with 28% ~ 30% Cr2O3 content for the reason that dressing plants can not be operated for investment lack. High grade chromium ores have been treated in heavy media separation plant before 1990. It is presented flow sheet, figures and necessity to put in operation HMS plant in the paper. Actually, low grade chromium ores with content 16% ~ 20% Cr2O3 are not enriched for the lack of investments, but before 1990 they have been concentrated in dressing plants producing chromium concentrates grade 48% ~ 50% Cr2O3. In the paper are shown technological schemes and industrial figures during more than 20 years operation and possibilities to reconstruct these mineral processing plants. Only chromium mineral processing plant of Bulqiza is in operation using as raw material its old existing tailings. The flow sheet and figures show that are possibilities to increase recovery and grade of concentrate in the plant. Separation and concentration of slimes in suitable equipment gives visible improvement of Cr2O3 recovery. Several tests have been carried out with flotation and magnetic separation methods for enrichment of low grade chromium ores. Flow sheet and figures of mineral processing ores content olivine as gangue mineral are interesting, because combination of gravimetric with magnetic methods is necessary in this case. In the paper are presented the tests and good results of low chromium ore pre concentration. Metallurgical treatment of chromium ores to produce Ferro chrome, as well as technological process, figures, consume of electrical power and materials in Elbasani and Burreli furnaces are shown and necessary investments to treat in metallurgy all produced chromium ores in Albania are considered.

Jan 1, 2014

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By W. Fander, Zhonghan Zhang, T. Choo, J. Enraght-Moony

"This paper describes the mineralogical and metallurgical procedures used to determine the recovery and concentrate grade of heavy oxide minerals occurring in lode deposits. The data produced also provide vital information to the processing engineers, which allows them to develop the most suitable flow sheet for that particular heavy mineral, here called an Economic Oxide Mineral (EOM). It demonstrates how results are interpreted to ensure that the proper process is used at each treatment stage to optimise recovery and to produce the most suitable concentrate at that point. Reference is made to some of the current equipment and techniques that can be used to process EOMs. The paper shows that when assessing the economic potential of a new ore body, or existing ore treatment plant, ore characterisation (OC) is necessary. This is especially true for EOMs such as cassiterite (SnO2), wolframite ((Fe, Mn, WO4,) pyrochlore ((Na,Ca)2Nb2O6(OH,F)), and tantalite (MnTa2O6) where often what seem to be small changes in ore types can have major effects on recovery and concentrate grade. Due to advances in flotation technology scheelite (CaWO4) in some deposits can be less vulnerable to OC variability than other EOM’s. Thorough mineralogical examination is shown to be the fundamental basis of correctly undertaking OC. This is because mineralogical analysis identifies each of the steps required to ensure that all ore types and zones are recognised, and differences explained, and shows the benefit in using reference samples to compare differences in the ores. The OC methods used for EOMs containing metals such as tantalum, tin, tungsten and niobium are similar; if two or more of these EOMs occur in one deposit as separate minerals, then OC will show when and how these minerals should be separated. The OC techniques described for EOMs can also be tailored for other heavy minerals, precious metals and graphite."

Jan 1, 2014

By Jannie van Deventer

"Innovation in the minerals industry has been lagging behind comparable industries like oil and gas. An incremental innovation culture that tolerates long lead times between invention and adoption has been exacerbated by a research grant structure that inhibits radical idea generation. Entrepreneurs who can make the link between ore source, technology and finance will cause a shift in innovation culture and open up substantial opportunities in the minerals industry of the future. By extrapolating existing trends in technology within and outside mineral processing, a crystal ball vision of future innovation is shaped with the aim to lower energy and water demand, reduce CO2 emissions, decrease operating and capital costs, reduce environmental impact, and secure a social licence to operate. Advances in nanotechnology, advanced materials and biotechnology will impact mineral processing, but the initiative for technology transfer must come from mineral processors. Laminates of graphene oxide can offer efficient filtration and separation media, while microfluidic devices will be used for desalination, solvent extraction and analysis. Substantial progress is expected on benign lixiviants and separation agents, such as nanoscale supramolecular hosts that can serve as high-capacity, selective and recyclable ligands and sorbents, and solid aminobiphosphonate-based adsorbents. Radical ideas for the recovery of precious metals from non-assayable ores and the generation of energy above unity will be adopted in selected minerals projects. In-situ mining in which microbes generate lixiviants at mineral surfaces will simplify processing circuits. Specific ores will be subjected to microwave processing and electropulse liberation to enhance recovery. Ultrafine grinding using devices of low energy consumption will be done mainly dry, followed by dry separation. New flotation cells will remove efficiently either coarse particles or ultra-fine particles, with mineral surfaces being modified not just by new reagents but also by selective microbes. Innovation in mineral processing indeed has a bright future."

Jan 1, 2014

By Kyle Bartholomew, Robert McIvor

"Functional performance analysis of closed circuit grinding provides valuable insight into the two components of ball mill circuit grinding efficiency: classification system efficiency and mill grinding efficiency. Classification system efficiency isolates the combined effect of classifier performance and circulating load ratio from other circuit variables, such as ore grindability and the mill grinding environment. Optimization of classification system efficiency ensures grinding energy is applied to particles needing further size reduction and not to overgrinding. Entirely based on size distribution data, classification system efficiency precisely distinguishes subtle changes in classification system performance. Use of the functional performance equation to isolate mill grinding efficiency allows for proper optimization of the mill grinding environment by isolating confounding effects of changes in classification and ore grindability. Variables such as mill percent solids and grinding media selection can be optimized using the mill grinding efficiency subcomponent of functional performance. First published by McIvor in 1988, the functional performance equation provides a set of standardized, quantitative optimization criteria, simple and powerful, which link circuit performance to plant design and operating variables that can be manipulated. Functional performance optimization has been applied in numerous mineral processing plants globally and continues to gain acceptance as a practical means for grinding circuit optimization. In this paper, examples of derivation and industrial application demonstrate the means by which functional performance analysis dissects grinding circuit efficiency into its subcomponents allowing the reader to apply this straightforward, powerful optimization methodology at their mineral processing operation."

Jan 1, 2014

By William J. Schloemer

INTRODUCTION The history of coal mining the Ostrava Region of the Czech Republic goes back nearly 250 years. Both coking coal for steelmaking and thermal coal for the production of energy are mined here; however, it was the coking capabilities that subsequently turned the region into a major steel-producing area in the early 1800?s, something that continues to this day. Ostrava lies in the northeast corner of the Czech Republic, near the southern border of Poland, and falls within the Upper Silesian Coal Basin. The region contains over 400 seams of coal of which about 150 have been mined over its history and continue to be mined. Eighty percent of the Upper Silesian coalfieldlies in Poland and is presently mined by about 35 coal mines; the remaining 20% falls in the Czech Republic, which presently has four mines operated by OKD, a.s., a subsidiary of Amsterdam-based New World Resources. Traditionally, all the mines in this region have employed the longwall method of mining, of which subsidence is an unavoidable consequence. In fact, due to the long history of longwall mining here, there are areas where the overall subsidence has exceeded 37 meters (121 feet). The region is fairly densely populated with residences and industry, and a considerable amount of coal lies under some of these areas where subsidence is not allowed or has to be minimized. It is this reason that has driven OKD to consider alternate methods of mining that will not create subsidence. The decision was made to consider the room and pillar method of mining in order to leave stable pillars of coal to support the surface. After considering several locations, OKD chose the shaft safety pillar at the CSM mine as a test mining location. To say the least, this is a very challenging location in which to conduct a test. As with the entire region, there are many faults from tectonic activity, the seams are pitching at 12 to 20 degrees, the area is affected by high horizontal stress, and the depth of 750 to 900 meters is perhaps the deepest room and pillar coal mining ever attempted.

Jan 1, 2014

By E. Hulthén

Cone crushers are used in the mineral, mining, and aggregate industry for fragmentation of rock materials. Control systems for cone crusher settings are widely used to compensate for wear and to protect the machines. The eccentric speed in a cone crusher affects the number of compressions the material is exposed to and thus the particle size distribution of the product. Eccentric speed also affects crusher capacity. However, the speed of the crusher is mostly fixed, because speed changes must be made by shifting pulleys, a process which is quite time-consuming. By applying a frequency converter, which has decreased in cost during recent years, it has become possible to adjust the speed continuously. By also applying mass-flow sensors to the process, the crusher can be run optimally to yield the most sellable products in a given moment. Existing systems normally only protect the machine. The sensors can be mass-flow meters, e.g., conveyor-belt scales. To analyze data from the process and calculate the appropriate value for the speed, an algorithm has been developed. The developed algorithm was tested and evolved at a crushing plant for aggregates that produces around 350 kton a year. The algorithm was implemented in a computer that could communicate with the frequency controller, retrieve data from four mass-flow meters, and also interact with the opera-tor. The computer was reachable over the Internet for the researchers at Chalmers and the algorithm was tuned and improved on-line. The result is a crushing stage that consistently and maximally produces the most desirable product. The performance (yield of required products) increased by 4%. As a bonus, the lifetime of the mantles increased 27% on the evaluated crusher.

Jan 1, 2014

By Egbert Burchardt

"Some of the challenges faced by the mineral industry in the future are the need to process low grade ores at the lowest operating cost, to deal with elevated energy cost and to address scarce water resources in some regions of the world. These challenges will increase the demand to develop highly energy-efficient and less water-consuming mineral processing systems. Experience from other industries suggests that HPGRs could help to achieve these goals, due to their high energy efficiency and their ability to be used as dry grinding systems. Historically, HPGRs have been used mainly as tertiary crushers in mineral applications for the production of ball mill feed. In the cement industry, however, HPGR systems have been successfully applied for grinding limestone, clinker and slag to a final product fineness (p80) of between 30 and 90 µm without the need of downstream ball milling. The total energy consumption of HPGR finish grinding systems in the cement industry has been found to be 30 to 50 % lower than in ball mill systems. This leads to the question of whether the same methodology can be adopted in the mineral industry. Such a step would require the use of dry rather than wet grinding systems. Traditionally, dry grinding systems have been only an exception in mineral processing, since most post grinding processes are wet. However, there are successful - mainly ball mill based - dry grinding examples in gold, nickel or iron ore. Experience from some of these dry grinding references are summarized in this paper. In addition, this paper explores two future-orientated questions: What opportunities does HPGR finish grinding offer the mineral industry? What are general conditions and challenges for adopting this technology for mineral applications?"

Jan 1, 2014

By R. V. Ramani, R. Stefanko

"The favorable mining conditions in the United States of America that resulted in the development of the highly productive room and pillar systems are largely disappearing. Increasing mechanization, poorer natural conditions, and greater concern for health, safety and environment gave impetus to the enactment of the Federal Coal Mine Health and Safety Act of 1969. These regulations prescribe more stringent requirements in face ventilation and mine air distribution, necessitating significant changes in existing ventilation systems. Stringent mandatory standards were applied to respirable dust control for the first time, and simultaneous control of both gas and dust has affected the face as well as primary distribution, most notably on haulage entries.The size and complexity of the present-day mining operations, and the need to evaluate various system changes in a limited time, call for scientific methods in mine planning. In this paper, the authors trace the previous applications of computers to mine ventilation planning and discuss the results of their work in applying a ventilation simulator developed at Penn State. The paper includes an analysis of current trends and suggestions for future research and development."

Jan 1, 2014

By Orion Ciftja, Arjan Ciftja

"The directional solidification method is routinely used to produce polycrystalline silicon, an important material for the photovoltaic (PV) industry. The form of the solid-liquid interface during solidification has considerable influence on the material quality. The dissolved impurities and the solid inclusions above the solidification front affect the interface and may cause interface breakdown. We investigate the effects of pushing and engulfment of silicon carbide (SiC) particles by the solidification front during directional solidification of silicon. We employ a 12kg directional-crystallization furnace to cast the molten silicon. We use upgraded metallurgical grade silicon with low concentrations of metallic impurities (< 5ppm) and a high content of carbon (700 ppm) present as SiC particles. Samples from the cast polycrystalline silicon ingots are investigated by light microscope. The expected interaction of impurities with the solidification front is investigated theoretically using empirical models. The data obtained from the models are in good agreement with the experimental results.IntroductionDirectional solidification is a well-known method for producing multi-crystalline silicon for the PV industry. In this method a planar front, achieved during solidification, results in a clearly defined interface between the solid and the liquid phase. The solubility of major impurities is higher in the liquid than in the solid phase. Therefore, directional solidification will work as a purification process where the impurities are retained in the liquid phase [1]. Apart from the process of removing the dissolved elements in molten silicon, the directional solidification plays also another role. It will interact with the solid particles that may be present in the melt. When a liquid containing an insoluble particle is solidified, three distinct interaction phenomena are observed: engulfment of particles, continuous pushing, and entrapment [2]. The term “engulfment” is used to describe incorporation of a particle by a planar interface, and the term “entrapment” is used for particle incorporation by a cellular or dendritic interface (see Figure 1) [3]."

Jan 1, 2014

By A. Scheltema Beduin, M. Kalisch, E. Floch, R. J. Dijkhuis, H. J. Oterdoom

In metallurgical copper production, the traditional aim is to increase recovery of copper to the maximum. SMS Siemag (SMS) has supplied numerous furnaces for this application. New targets are to make sure end of line products are as safe as possible with respect to health and environment, and to maximize raw material utilization. This means a for example a minimization of leachable metals in slag, so it can be safely used as a construction material, and either a targeted concentration or fixation of volatile compounds, such as arsenic. Currently, 2 process routes are generally applied for slag cleaning. The first is grinding followed by flotation, and the second is slag cleaning in an (electrical) furnace. Popularity of both options has fluctuated over the years, and currently the milling-flotation seems to be the more popular option. In this article some of the advantages and disadvantages of both methods are described, and especially how long term environmental policies could have an impact on the decision which process route to choose. Finally, this article will describe some of the developments SMS is working on in pyrometallurgical slag cleaning that could influence the direction for the design of the copper plant of the future.

Jan 1, 2014