Search Documents

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By Masoud Askari, Ahmad Rafizadeh, Shahamat Rostami, Mohammad Qaredaqi

Gole - Gohar Iron ore mines located in Sirjan, Southeast of Iran, have more than 1 billion Iron ore deposit and this area comprises 45 % of Iran Iron reservoirs. The aim of Wet tailing processing line is recovering Hematite ore from wet tailing of Gole - Gohar iron ore processing plant. The Investigations of Hematite recovery plant showed that the recovery of Iron ore to concentrate in Wet Tailing Processing (WTP) line is very lower than that has been predicted, sampling, and designing of the process parameters are not accurate and designed magnetic field intensity is not reasonable for the recovery of Iron in form of Hematite in this line feed. Applying of MIMS in WTP separator and changes in circuit caused in overwhelming increase of Fe recovery, from 11 to 40%. Although recovery of WTP line was improved, but low recovery of this processing line and high content of Hematite ore in WTP tailing, made applying Wet High Intensity Magnetic separators unavoidable. Two kinds of WHIMS have tested for processing of WTP line tailing. Results showed that traditional Jones separator with grooved plate matrix, is more suitable to achieve a better quality of concentrate compared to Slon® separator.

Jan 1, 2014

By T. S. Kagogo

The factors affecting haul truck tyre performance and the effectiveness of the management system at Rossing Uranium Mine were investigated with the aim of increasing tyre performance in terms of running hours until failure. The main objectives were to identify the types of tyre failure, their causes and cost implications, and evaluate the effectiveness of the management system. A site severity survey, weight study, and TKPH studies were conducted to determine the pit conditions, and an analysis of failed tyres carried out. The results showed that tyre performance at the mine has declined from 2009 to date, and the increase in lost value amounted to R5.7 million in 2012 alone. The main cause of tyre failure is loose rocks in the pit. The present management system in the load and haul department is not effective enough due to operational constraints it is facing.

Jan 1, 2014

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By Matthew Thurley

Optimisation and control of comminution, pelletization, and agglomeration processes is a complex task with large potential for gains in productivity, energy efficiency, and particle size distribution quality. One factor in realising these gains is the requirement for fully-automated online particle size distribution measurement. Moreover, online particle size distribution measurement that is based on the particles on the visible surface and can avoid or mitigate substantial errors that result from under-sizing overlapped particles and over-sizing areas of fines particles. Literature review indicates a body of substantially 2D photographic based particle size measurement systems that suffer from a large number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited color variation in the material. In order to measure the visible particles on a pile there are a number of requirements including; avoiding particle delineation errors due to variation in material color and shadows, detect overlapping versus non-overlapping particles, and identify areas of fine particles as fines and not large rocks. Results are presented using a fully-automated online measurement system of crushed rock on conveyor belt using a 3D surface laser profile. The system provides continuous online measurement and results are shown on over four hours of production after the primary crusher. Size distribution results are calculated using volumetric estimation of the particles on the surface of the pile. The results show a strong capability to discriminate size variation especially in the 10% and 20% passing values. Furthermore results show that if areas of fines are misclassified as large rocks, and overlapped particles misclassified as small rocks, then a near complete loss of discrimination occurs for the P10 and P20 values which become largely constant values.

Jan 1, 2014

By M. Abdollahy

Solvent extraction of gallium from Bayer solution of Jajarm Alumina plant was investigated us-ing Kelex100 as extractant. Taguchi experimental design method was used in order to optimize the separation factor of Ga and Al. Optimum conditions were obtained as follows: Temperatuer: 65°C, volume ratio of aqueous phase to organic phase: 3.0:1.0, process time: 60min and organic phase containing 15vol.% Kelex100, 5vol.% isodecanol in kerosene. In this conditions, 74% gallium and 0.3% aluminum was extracted and separation factor was obtained 828.63.

Jan 1, 2014

By P. K. Hofmeyr

Traditional fire assay dates back over 3000 years and has changed very little over that time. The only improvement is to replace the gravimetric finish with dissolution of the Precious Metal bead followed by AA or ICP analysis of the solution. The newly developed FIP A (Fast In-line Fire Assay) method allows full automation of the fire assay process from sample preparation to spark analysis of the Pb button. This results in fully quantitative analyses for Pt, Pd, Rh, Ru, lr, Au and Ag in typically less than an hour after a sample is entered into the system. Detection limits are theoretically Pt 0.08 ppm, Pd 0.002 ppm, Rh 0.002 ppm, Au 0.08 ppm and Ag 0.002 ppm but in practice the lower measurable limits are about double these figures. Few opportunities have been available to present data obtained using the FIFA system as all FIFA laboratories have been in the domain of a Pt mining company which prefers to keep all Pt analytical matters confidential. However, IMP has recently participated in the round robin exercise to establish recommended values for a new series of Merensky Reef and UO-2 Layer reference materials produced by African Mineral Standards. The precision of the results was excellent being on average Pt 2.05%, Pd 1.25%, Rh 4.08% and Ru 4.94% being expressed as Relative Standard Deviation. The excellent precision is a reflection of the efficient collection of POEs in the Pb buttons and the homogeneity of the Pb buttons. However, the accuracy was not as good. The poorer accuracy is interpreted as the calibration of the spectrometer not being as good as desired due to the difficulty in acquiring a suitable range of standards with reliable recommended values for the PGEs. The most recent spectrometer was calibrated with the greatest care and produced slightly better results for Pt, Pd and Rh and slightly worse for Ru.

Jan 1, 2014

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

By Sebastian Schmuck, Petrico von Schweinichen, Dieter Senk, Mohammad Peymandar

"At Department of Ferrous Metallurgy of the RWTH Aachen University in Germany steels in the system Fe-Mn-C(-Al) are investigated and produced in the framework of the SFB 761 ""steel-ab initio"". A new world of steel grades leads to special challenges regarding the production and recycling at the end-of-life cycle of product. In order to recycle high manganese steel alloys the EAF has to be chosen preferentially. A good slag practice is necessary avoiding loss of manganese content during melting in the EAF. This paper investigates on the reaction kinetics at the interface of slag and steel containing Mn (17-22 wt.-%) and up to 3 wt.-% Al. The effect of changes in the composition of slag and steel on the interfacial reaction kinetics is studied. The thermodynamic software FactSage™ is utilized to calculate the composition of slag and steel at equilibrium.IntroductionTRIP and TWIP steels are highly alloyed steels which show superior strength and ductility when compared to standard carbon steel and stainless steel alloys. These TRIP- and TWIPsteel grades contain typically 15-30 wt.-% manganese, 0-4 wt.-% silicon and aluminum, and up to 1 wt.-% carbon. Steels containing 18-28 wt.-% manganese and 0.7-1.2 wt.-% carbon together with aluminum addition from 3 to 12 wt. -% and without silicon refer to TRIPLEX high manganese steel alloys. These alloys combine high strength at even large ductility [ 1-4]. At the Department of Ferrous Metallurgy (IEHK) of the RWTH Aachen University in Germany, steels in the system Fe-Mn-C(-Al) is under investigation at the collaborative research center, SFB 761 ""Steel-ab initio"". In this project, high manganese alloyed TRIP and TWIP steels are in the focus.The mechanical properties such as high strength and high ductility make this kind of steels perfect candidates for impact absorption applications in auto body such as vehicle doors and bumpers [2, 5]. With increasing the use of TRIP-, TWIP- and TRIPLEX-steels more high manganese steel scraps will be available at the end of life cycle of products, which need to develop the technologies and metallurgical processes to recovery of high manganese steel. A new steel grade brings new challenges in recycling. In order to recycle high manganese steel scraps the electric arc furnaces (EAF) have to be chosen preferentially [1]. Nevertheless it's not easy to prevent the manganese loss during the process in EAF. During the oxygen refining of high manganese molten steel in EAF the manganese content decreases strongly by oxidation and vaporization, which is affected by slag composition, slag properties such as basicity and viscosity, slag weight as well as melt temperature [6-8]."

Jan 1, 2014

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By K. A. Stanley, N. A. Karl, D. R. Wilburn

"This summary of international mineral exploration activities for the year 2014 draws upon information from industry sources, published literature and specialists in the U.S. Geological Survey (USGS) National Minerals Information Center. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry.Three types of information are reported and analyzed in this annual review of international exploration: 1) budgetary statistics expressed in U.S. current dollars provided by SNL Metals & Mining (SNL) of Charlottesville, VA; 2) regional and site-specific exploration activities that took place in 2014 as compiled by the USGS and 3) regional events that affected exploration activities including economic, social and political conditions, which were derived from published sources and discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop these compilations, statistics may differ depending on the source and type of data that are being reported.The SNL data summarize planned company budgets for worldwide exploration activities in 2014 for 19 nonfuel mineral commodities based on company surveys. Research focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (iron ore, phosphate and potash), and specialty mineral commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included for the first time in 2007. Data on lithium, niobium, phosphate, potash, rare-earth elements and tantalum were compiled for the first time in 2010 because of their increased significance. Since 1999, companies with exploration budgets of $100,000 and greater were included in the SNL compilations. SNL budget estimates exclude bauxite, coal and oil and gas. Exploration budget estimates for iron ore have been compiled since 2011 but reported separately. The 2014 SNL company survey is reported by SNL to cover an estimated 95 percent of the world’s nonferrous, nonfuel mineral exploration budgets. The 5 percent that is not covered includes companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities"

Jan 1, 2014

By P. Ross, O. Rielo, P. Katsabanis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. The paper reviews all available experimental information, ranging from small and medium scale tests in geologic materials to small scale tests at the laboratory and synthetic materials, simulating rock. Tests have been re-analyzed and discussed in terms of the information they present and the limitation of the testing environment in representing actual conditions. New results obtained from blasting experiments in specimens made of a grout have provided a clear picture of the effect of delay on fragmentation. The grout used has a strength of 60 MPa (8700 psi), density of 2.5 g/cm3 and P-wave velocity of 4000 m/s (13100 ft/s). Each block was placed in a yoke to eliminate unwanted reflections and the desired delay was obtained using the appropriate length of detonating cord between holes or sub-millisecond electronic detonators. Delays ranged from 0.1 ms/m (0.03 ms/ft) of burden to 16 ms/m (4.9 ms/ft) of burden. Fragmentation was obtained using screen analysis of the collected fragments. Delay time has been shown to be a significant parameter affecting fragmentation and back break. Generally larger fragments and less back break was observed at short values, while fragmentation somewhat deteriorated at significant delay times, compared to what was observed at intermediate delay times. The work is now extended to include the effect of energy partition on fragmentation as well as the effect of initiation point and coupling ratio.

Jan 1, 2014

By A. Newman, A. Brickey

Although some of the prevalence of openpit production scheduling software can be explained by the predominance of openpit mining throughout the world, other factors have led to a lag in corresponding underground software. We explain mathematically why underground production scheduling is more difficult than its openpit counterpart and provide directions for research in the underground scheduling arena.

Jan 1, 2014

By R. J. Hundermark, L. R. Nelson

The critical importance of tap-hole design and management to furnace performance and longevity is explored through examining some of the specific matte, metal and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloys smelting and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally core aspects of tap-hole equipment and maintenance are identified that are considered important to securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance.

Jan 1, 2014

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"The worldwide demand for ornamental stones in building construction is motivating the use of their wastes, generated during fabrication, to produce compound stones. This work has as its objective to investigate the production of an ornamental compound marble (OCM) under vacuum and compression processing of a polyester matrix composite with addition of marble waste as load and as filler. Square OCM composite plates were subjected to compression and flexural mechanical tests. Samples were analyzed to obtain the density and water absorption. The OCM composites presented properties within the expected range of an artificial stone.IntroductionMarble is a limestone, composed mainly of calcite, more or less crystallized by metamorphism that ranges from granular to compact in texture. It has a density 2.7 g/cm3 and its porosity is approximately 0.4%. The UNI 8458 standard defined marble as: ""every crystalline rock constituted mainly by minerals with a Mohs hardness equal to 3-4"". In marble production around70 - 75% of whole extract material is lost in byproducts generation [1,2].In function of large volume of residues generated, the ornamental stones industry has attracted ever more the attention of environmentalists [3].Actually the marble can be pulverized to obtain calcium carbonate for industrial applications. It is also possible to obtain a thinner powder to produce concretes [l]. Some authors study the use of stone residues in concrete mortars and ceramic bricks, getting better properties to these materials [3,4].The marble residues can be also used in engineered stones, or ''agglomerated"" stones, production. The most common engineered stones in the market consist, like a polymer concretes, in polymer matrix composites incorporating petreous components. In the formulation of the engineered stones, the particulate or granular petreous components are the result of fragmentation or trituration processes to which natural stones were submitted to [ 5]."

Jan 1, 2014

By Anders Erlandsson

"The crude ores from the LKAB mines are sorted and refined into a number of products. As there are a number of different plants the flow of material is often complex.in connection with studies of a proposed extensive investment program it was necessary to get a good measure of the changes which would be caused in the total profit by the different possible investments. A linear programming model was set up to accomplish this, and to cover the consequential effects on the production system. The objective function of the model maximized the total profit, taking into account restrictions in materials balances, blending conditions, production capacities and market. The changes in total profit resulting from the different investment alternatives, together with investment and fixed costs, were used in a series of investment analyses. The application has proved to be very successful and the results come very near to what was expected."

Jan 1, 2014