Search Documents

By Xiao Long, Ting Wu, Lilong Zhu, Qian Wang, Shengping He

"During the continuous casting of peritectic steel slabs, mould fluxes with high crystallization capacity are usually chosen for improving slab surface quality. However, the lubrication condition of casting shell also could be deteriorated. Since precipitation of crystals within liquid slag film can change the composition and property of liquid slag over solid-liquid slag film interface region, its impacts on continuous casting process also are not clear. In order to clear this phenomenon, an experiment method was put forward, and mould fluxes for peritectic steel slabs continuous casting were selected and examined. The results reveal that after crystals have been separated, the crystallization capacity of leftover liquid slag increased with different levels, which could deteriorate the lubrication condition of casting shell and cause a series of problems. Thereby, mould fluxes with high crystallization capacity at beginning for heat transfer control and then weaker after crystallization should be considered in the future.IntroductionIn the continuous casting of peritectic steel slabs, contradiction between heat transfer control and slab shell lubrication by mould fluxes has been treated as a key problem for maintaining a smooth manufacturing process [ 1]. Strong and uneven horizontal heat flux over the meniscus region will cause uneven solidification of casting shell, especially for peritectic steel slab with enormous volume change caused by phase transition. All of those could cause surface defects like longitudinal crack [2-4]."

Jan 1, 2013

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By S. R. Amos, N. O. Lotter, A. L. Hannaford, J. F. Oliveira, D. W. Broughton

"Ivanplats Ltd appointed Xstrata Process Support to perform the flowsheeting development work for their hypogene and supergene geomet units of the Kamoa Copper deposit, located in the Democratic Republic of the Congo. Through systematic flowsheet development using modern Process Mineralogy, the optimised milestone flowsheet delivered a saleable concentrate grade of 32.8% Cu at 85.4% recovery with hypogene ore, and a saleable concentrate grade of 45.1% Cu at a recovery of 83.4% for supergene ore. The significant value of this development is that a single flowsheet will treat both hypogene and supergene ores and produce saleable concentrates. Further work to advance the flowsheet performance has been identified for investigation in the near future.INTRODUCTIONLocation and Description of the Kamoa DepositThe Kamoa copper resource is located some 40 km west of the city of Kolwezi, in the south west of the Katanga Province of the Democratic Republic of the Congo, in the region of Central Africa. Drilling at Kamoa in 2008-2009 had discovered laterally continuous, sediment-hosted, high-grade stratiform copper mineralisation in a newly discovered copper district that forms a previously unrecognised western extension of the famous Central African Copperbelt – which hosts such world-class deposits as Kolwezi, Tenke-Fungurume, Konkola and Nchanga. This discovery showed that the western end of the Copperbelt in the Congo does not terminate at Kolwezi (Friedland & Broughton, 2009). The resource contains hypogene and supergene geomet units with a transitional zone located inbetween the (upper) supergene and the (lower) hypogene. In the hypogene unit, the major copper sulphides are bornite, chalcopyrite and chalcocite, whilst in the supergene, the sequence is led by chalcocite, then bornite, and finally chalcopyrite. Covellite is present in both units as a minor copper sulphide. Both geomet units will be mined and treated in one concentrator, either as blends or as campaigns."

Jan 1, 2013

By R. W. Macqueen

Organic matter commonly associated with Mississippi Valley-type (MVT) lead-zinc deposits may be used to assess the burial/thermal history of host rocks and sulfides. Organic matter may also have been involved in the genesis of H2S required to precipitate sulfide ores. Pine Point, Northwest Territories, Canada, provides an example. Located on the south shore of Great Slave Lake, Pine Point is an operating world class deposit which has produced 58 million tons of ore containing 3.0 percent Pb and 6.1 percent Zn from more than 40 Individual orebodies. Well-documented paleokarst features in a Middle Devonian carbonate complex are the main ore hosts. Sphalerite and galena ores are mainly open space fillings, and, from fluid inclusion studies, were deposited from saline fluids at temperatures of up to at least 100°C. Forms of organic matter occurring in the Pine Point barrier-reef complex Include indigenous organic matter, heavy oil and bitumen. Based on numerous geochemical criteria, it is clear that heavy oils and bitumens were derived locally from indigenous organic matter. The geochemical character of the Indigenous organic matter demonstrates that the barrier-reef complex is immature to marginally mature with respect to petroleum generation, and has not been heated above about 60°C maximum. Thus sphalerite with fluid inclusions that yield temperatures up to about 100°C represents former thermal anomalies. Bitumen is of two main forms at Pine Point: widespread soft, tarry material soluble in organic solvents (unaltered bitumen); and hard, brittle, glassy material that is mostly solvent-insoluble, and associated with white sparry dolomite and lead-zinc ores (altered bitumen). There are also partly altered bitumens. Unaltered bitumens have atomic H/C ratios of about 1.4, sulfur contents averaging 7.8 percent, and sulfur isotope ratios 634S) of approximately +4.6 per mil. Altered bitumens have atomic H/C ratios averaging 1.02, sulfur contents averaging 22 percent, and 634S values of about +12.9 per mil. These data and the organic geochemical character of a large suite of bitumen samples analyzed, strongly support the concept that some bitumen has been involved in the thermochemical reduction of sulfate to produce the H2S required to precipitate the ores. Mass-balance calculations indicate that the amount and degree of alteration of bitumen is more than enough to account for the reduced sulfur species deposited as metallic sulfides at Pine Point. MVT deposits, including Pine Point, seem to require the coincidence of available metallic Ions, pre-existing pore space, and a precipitating agent. A close look at organic matter in more MVT settings may outline trends in distribution or alteration which can be used as indicators of past thermal environments and processes of ore deposition.

Jan 1, 2013

By E. McCullough, D. Preece, M. Ortel

The mining and oil industries employ techniques such as geologic mapping, core drilling and electromagnetic field techniques to explore for new deposits. New discoveries of major near-surface ore bodies are becoming progressively rare and traditional exploration methods are unable to resolve ore bodies deeper than about 500 m (1640.4 ft). Consequently high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3 km (1.9 mi).

Jan 1, 2013

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By Ben C. Gerwick

This publication is intended to document recent innovations and technologies that have the best potential for effectively improving the quality of marine foundations while reducing the cost, time and risk of construction. Marine foundations originated in Neolithic times with the Swiss Lake Dwellers who constructed pile-supported houses, safe from invading tribes. The Queen of Babylonia built the first recorded bridge in 1500 BC across the Tigris. The foundations were large flat stones laid on the river bottom. About the same time in India, builders extended their water well techniques to the construction of ?well? foundations in the beds of their rivers. These were really the first open caissons; brick walls were built up in a circular ring while divers excavated sand from the bottom, sometimes at a depth of 100 feet. The Romans extended the clay-filled cribs of the Middle East to shallow cofferdams, which they sealed by underwater concrete made with pozzolanic cement from Mt. Vesuvius.

Jan 1, 2013

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Stephen C. Tadolini

Effective barrier pillar design is an essential component for safe and productive underground coal mining. Barrier pillar design methodologies that incorporate sound engineering judgment have been used for practical everyday usage. The next logical step is to utilize numerical modeling techniques that help combine practical experience and empirical observations into barrier pillar design analysis. A case study is presented that describes the barrier pillar design process, but also highlights the importance of considering the global mine response by evaluating: adjacent pillar stabilities, impact of intersection and entry widths, capacity of primary and secondary bolting systems and rib stabilization used for the safe and efficient removal of the longwall face equipment.

Jan 1, 2013

By Neely H. Bostick

The primary and secondary organic matter in sedimentary rocks changes markedly when it becomes heated as a consequence of thick sediment accumulation and normal geothermal gradients, high geothermal gradients, hydrothermal fluids, or igneous events. Contact zones adjacent to small igneous dikes allow sampling of a single sedimentary bed that has been exposed to temperatures in a range as great as 30-500°C. Dike-heated rocks are, therefore, good sites for research on thermal effects because variation of the original organic matter is minimal, the range of heating is great, and the history of rock heating in a dike zone is relatively well established. In rare cases, such as at the dike near Wolcott, Colorado, described in this paper, the rock samples are sufficiently unweathered to allow analysis of secondary bitumens generated by the heating. We show by optical microscopy, scanning and transmission electron microscopy, and geochemistry the kinds of solid organic constituents in sedimen¬tary rocks and in ore deposits and the effects of heating. The primary phytoclasts that make up kerogen In sedimentary rock and in some ore deposits (pollen, resin, charcoal, humified woody remains, etc.) change in ways that are familiar to coal specialists. Progressive loss of moisture and other volatile matter yields residual kerogen that Is relatively higher in carbon and lower In oxygen and hydrogen, and has greater molecular or polymer ordering. In our contact zone examples, atomic H/C ratios of kerogen decrease from 0.8 (one case from 1.4) to 0.4, the hydrogen index from Rock-Eval pyrolysis decreases from 70 to 5, and the transformation ratio from Rock-Eval pyrolysis increases from 0.06 to 0.5 with increased heating. The visible effects of heating seen by scanning electron microscopy and light microscopy include formation of vesicles and flow structure, the development of optical anisotropy and mesophase, change of color, and increase in the refractive index, absorption, and reflectance. Some of these changes In primary organic matter are observed also in secondary organic matter, for example, in solid bitumens in sedimentary gold ores or In lead-zinc deposits. Quantification of color or absorption changes is difficult because it Is hard to make thin sections of organic matter with uniform thickness. However, natural objects with uniform thickness can be used. We show the colors of pollen In rocks from the Salton geothermal field at temperatures ranging from 100 to 300°C, and of pollen heated in laboratory bombs from 150 to 400°C. Measurement of vitrinite reflectance is a practical way to quantify thermal changes of kerogen and minerals of most sedimentary rocks because vitrinite is fairly widespread In sedimentary rocks of Devonian age and younger. For example, the reflectance of vitrinite rises from the regional level, as low as 0.4 % Ro, to more than 5% Ro adjacent to dikes that cut sedimentary rock. This is equivalent to the rank change from subbituminous coal to extreme meta-anthracite. The rise is most abrupt near thin dikes, but when the distance from the igneous contact is expressed as a ratio of dike thickness the reflectance rise is similar for all dikes. Controlled heating of vitrinite-bearing rocks In the laboratory provides a means to assign known temperatures to vitrinite-reflectance values. The derived plots of temperature In dike contact zones have the same shape and level as those predicted by heat theory, and the temperature lines extend toward dike contact temperatures that are about half those of most magmas, as expected if the intrusions did not flow past the sedimentary rock for a long time. The globular submicroscopic structure of vitrinite and Its heterogeneity, which we show by means of transmission electron microscopy, pose some problems In selecting a uniform type of vitrinite for measurement of thermal changes. At present, routine reflectance values of vitrinite dispersed in rocks have a relative uncertainty as great as 10%. Thermally caused chemical changes in the primary kerogen, especially decrease in the oxygen and hydrogen contents, lead to formation of secondary products in the contact zone. The measured changes of secondary organic products in these rocks include formation of peaks In concentration of total extractable organic matter and in hydrocarbons, and in the saturated/aromatic hydrocarbon ratio over the interval where primary organic hydrogen decreases most rapidly--then destruction or expulsion of these products at high temperatures. The odd carbon-number predominance of the C25-C31 n-alkanes In samples far from the dike disappears by about 1.3% Ro whereas the 13C: 12C ratios of the saturated and aromatic hydrocarbons increase over most of the thermal range. The saturated aromatic hydrocarbon ratio at first increases, corresponding to thermal generation of saturated hydrocarbons, then decreases in the most altered samples. One use of organic petrography, in addition to identifying organic fades or thermal alteration, is recognition of sample contamination such as the solid organic additives used in some drilling muds which may contaminate geochemical samples.

Jan 1, 2013

Mining is big business in Ontario. The province is Canada?s leading mining region. It consistently ranks among the top 10 jurisdictions worldwide for exploration spending, reaching about C$1 billion in 2011. More than 26 percent of all exploration and appraisal dollars spent in Canada are invested in Ontario. Minerals produced include nickel, copper, platinum group elements (PGE), cobalt, zinc, diamonds, gold and silver. It was reported that there are more than 600 mining exploration projects in the province. And, recent discoveries of chromite in northern Ontario?s Ring of Fire will add to the province?s mineral production in the coming years.

Jan 1, 2013

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By John C. Ruckmick

Elemental sulfur deposits generally can be classified as either volcanogenic or biogenic. The latter can be divided into biosyngenetic and bioepigenetic deposits. Essentially all economically important sulfur deposits are bioepigenetic replacements of anhydrite or gypsum in basins containing evaporites and hydrocarbons. Anaerobic bacteria utilize the oxygen of sulfate ions to oxidize hydrocarbons to C02 and reduce the sulfate to H2S. Sulfur deposits are formed by concomitant and subsequent oxidation of the H2S. These bacterial systems can operate on enormous scales, producing deposits containing over 200 million tons of elemental sulfur. There are no known "old" sulfur deposits; almost all known deposits are younger than Miocene and most are still actively forming today. Therefore, it is probable that, with burial and time, sulfur deposits are converted to sulfide deposits. Perhaps more important, bacterial oxidation of hydrocarbons and resultant production and trapping of large quantities of H2S appears to be the logical explanation for the location of many important metal sulfide deposits such as the Mississippi Valley type lead and zinc deposits.

Jan 1, 2013

Blastserve, ISEE’s Listserve is being replaced by our new Blasters Forum-online, an exclusive member benefit. Our goal is to provide an ISEE forum for you to network with your peers and exchange technical information and get answers to your technical questions. This forum is unique in the fact that only ISEE members are permitted to review or post on the site. Over time you will be able review the discussion history and use the archived discussion as a valuable resource for trends in the industry. The following are a sample of the discussions that too place recently on Blastserve

Jan 1, 2013

By G. R. Morin, A. R. Leggett

"In 2010, closure of the Kidd metallurgical plants along with structural changes to the historical ratios of payable metals led to a review of the operating targets at the Kidd concentrator. Previous operating data indicated that there was potential for significant revenue improvements by lowering the copper concentrate grade. An extended plant trial was carried out in 2011 to quantify the revenue impact of lowering the copper concentrate grade from 27% to 25% Cu, as well as identifying the lower practical grade limit. Analysis of plant trial results indicated that the process change increased net concentrate revenue by $2 M to $3 M per year at current metal prices. Increased revenue was primarily associated with higher silver recovery to the copper concentrate while the marginally improved copper recovery was essentially offset by increased zinc losses and concentrate treatment and freight charges.Details of the plant test work results are discussed in this paper along with the financial analysis of the revenue improvements. Key areas covered are major revenue components of the concentrate contracts, validation of revenue improvements through plant testing and sensitivity of the improvements to market and plant variables.INTRODUCTIONThe Xstrata Copper Kidd concentrator commenced operations in 1966 treating ore from the nearby Kidd volcanogenic massive sulphide deposit in Timmins, Ontario (Thompson, Amsden, & Chapman, 1978). Over the years, up to four separate grinding-flotation divisions were in operation with throughput rates peaking at 4.5 million tonnes per year of ore in the mid 1980’s (Kelebek & Francis, 1998). As the mine production decreased and grinding throughput increased operations were gradually cut back and since 1998 two grinding-flotation divisions have been in operation treating Kidd mine ore. One of the idled divisions has been intermittently used for custom milling operations, most recently the Ni/Cu Montcalm deposit, which was milled from 2004 to 2009. Current budget throughput rates, limited by mine production, are 2.4 million tonnes per year of ore grading 1.7% Cu, 4.3% Zn and 55 g/mt Ag. Concentrate production rates are 150,000 tonnes per year of copper concentrate and 155,000 tonnes per year of zinc concentrate. The Kidd mine is the deepest base metal mine in the world with mining operations down to 9600 ft.In 2010 the copper and zinc plants at the Kidd metallurgical site, which previously treated the concentrate production from the Kidd concentrator, ceased operation due to a variety of economic and market factors. Following the metallurgical plant closures the Kidd concentrator products were shipped off site for treatment. The majority of the copper concentrate is now processed at the Xstrata Copper Horne smelter in Rouyn-Noranda, Quebec with the majority of the zinc concentrate processed at Canadian Electrolytic Zinc Ltd. in Valleyfield, Quebec."

Jan 1, 2013

By William S. Fyfe

The world's biomass with its species-specific ability to concentrate metallic elements must provide one of the dominant concentration and transport systems for such elements. Given that about thirty elements are now considered bio-essential, for all these biomass may control their environmental behavior. Life appears to be present in almost all places where liquid water is present at temperatures near 100°C or below. In the surface environment a very large array of simple minerals are produced in living cells and such processes can lead to economic concentrations. Because of the specific nature of bioconcentration of elements, in all environments where biomaterials accumulate, interesting metal concentrations may occur or the molecular fragments from bio-degradation may allow specific metal transport and concentration. The scale of biological-inorganic interactions on our planetary surface is still inadequately appreciated.

Jan 1, 2013

By J. Lee, M. Peart, T. Bhambhani, D. R. Nagaraj, P. Riccio

"Over the past decade or so, our efforts have focused on developing the rationale and concepts for new technology in reagent development and optimization in the processing of base and precious metals. A major outcome of these efforts have been the development of a novel family of collectors, principally driven by the MAXGOLD® and Aero XD-5002® chemistries, for precious metals recovery from primary Au ores and Cu-Au ores. These chemistries was developed to be robust to address the complex mineralogy and gold deportment in these ores. Plant trial data for a variety of ores have confirmed that the both Aero® XD-5002 and MAXGOLD® chemistry are indeed versatile in recovering gold values occurring as gold alloys and/or associated with many types of sulfides, and in altering the deportment of certain sulfides (such as those bearing As, Bi etc). An overview will be given in this paper using plant data to highlight the application of these reagents.INTRODUCTIONThe subject matter of this paper is the flotation of Au containing minerals from their ores. The motivation from this manuscript comes from the several challenges faced with the processing of Au ores, as was articulated in detail by Nagaraj (2008). The biggest challenge is the complex mineralogy; most easy-to-treat free-milling ores bodies are largely depleted. The Au values are distributed in multiple host minerals such as pyrite, pyrrhotite, arsenopyrite and Cu minerals such as chalcopyrite. Au values also happen to be finely disseminated within the various minerals and are sometimes invisible in optical microscopy. Additionally, on any given day, some mines treat multiple ore types, and the mineralogy is different for each ore type.Xanthates continue to be the collectors of choice at most Au and PGM operations around the world. Most primary Au operations tend to consume very large amounts of collectors; the dosage ranges anywhere between 40-400 g/t and this has been attributed to both mineralogical and non-mineralogical factors (non-mineralogical factors include the low cost of xanthates and the mindset that “more is always better”, which is not necessarily the case). In addition, several studies now show that xanthates alone are never sufficient where multiple value minerals are present, and that supplementary collectors are required. The large doses present a substantial cost to the minerals industry, and many mining companies have expressed the need for more efficient reagents that can improve metallurgical performance at low dosages."

Jan 1, 2013

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By Denise Clarke

Homeland Security Qualifications (HSQ) personnel were instrumental in developing the UK’s suite of Explosive Substances and Articles (ESA) National Occupational Standards (NOS) (also known as "competences") on behalf of the Standards Setting Body for Explosives, Munitions and Search Occupations (SSB for EMSO).

Jan 1, 2013

By Huimin Lu, Lian Zhou, Panpan Wang

"For the low concentration C02 exhaust gas from coal-fired power plant, steel plant emission trapping and recycle problem, a pressure swing adsorption process was studied, using a porous imidazolate framework materials (ZIFs) as adsorbent, separating carbon dioxide from fuel gas mixture. In the carbon dioxide reduction condition by electrochemical method, using ionic liquids as electrolyte, the oxygen and carbon products could be obtained, including carbon nanotube, nano carbon fiber and amorphous carbon. At last, a new C02 collection, recycling and reuse technology was formed.IntroductionDuring the combustion of fossil fuel in coal-fired power plant or steel plant, large amount of carbon dioxide has continuously emitted into the atmosphere. The phenomenon has resulted in the melt of arctic glacier and the frequent emergence of abnormal climate. How to reduce the emission of carbon dioxide and protect human living environment has become a worldwide challenge. Recently, there are three routes to resolve this problem: The first one is to adjust the energy structure and develop new energy, such as solar, wind, hydrogen; the second one is to improve energy efficiency and avoid waste; the third one is to research capture and sequestration of carbon dioxide (CCS). But many researchers have come to realize that the recovery and utilization of carbon dioxide are more important than the sequestration of it. Because the captured carbon dioxide just buried under the earth maybe cause secondary pollution if carbon dioxide leak out from the adsorbent."

Jan 1, 2013