Search Documents

By D. Marsh

The feasibility study for the Grasberg Block Cave mine, finalized in May 2008, indicated a production capacity of 160,000 tonnes per day. A rail haulage system was an integral part of the mine design. This paper describes the simulation process used in optimizing the design and discusses the key factors and variables that impact the capacity of the system. The final recommendations for the haulage level layout and associated equipment are also included.

Jan 1, 2010

By J. L. Kohler

Component failures in the electrical control circuits of mining machines account for a large percentage of the total downtime of the machine, Once a failure has occurred it is always a tedious and usually a time-consuming task to locate the failed component. Moreover, the pressure to quickly locate the cause of a delay can lead to compromises in safety. Thus an onboard diagnostic system, essential for an automated machine, would be a very useful addition to existing machines. This report details U.S. Bureau of Mines development of a generic procedure for synthesizing diagnostic systems for electrical-control-circuit failures in mining machinery. A continuous mining machine is used as the testbed to illustrate the application of the developed methodology. Substantive differences among mining machine control circuits made it impossible to achieve a generic diagnostic system, but a generic approach for the synthesis of the diagnostic system was possible. As the research progressed, it became apparent that an algorithmic approach was better than an expert-system-based implementation. A prototype system was constructed and used to evaluate the diagnostic system. Prototype implementation issues are also examined.

Jan 1, 2010

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock formed by the consolidation of clay, mud and (or) silt. Government and legislative programs The U.S. Environmental Protection Agency (EPA) invited industry to nominate representatives to a review panel that will help the EPA develop rules to regulate air toxics from the production of brick and structural clay products. The EPA was required to establish a review panel because these regulations will significantly affect small businesses. The regulation of air toxics falls under the Clean Air Act.

Jan 1, 2010

By Charles Vaught

The purpose of this study was to determine mine workers' state of fie-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 2010

By P. L. Swanson

Over a recent 20-month observation period, the U.S. Bureau of Mines obtained seismogram records from a single vertical-component, short-period seismometer installed at the surface of a metal mine in northern Idaho. The seismic events were analyzed for local (Richter) magnitude (M), time of occurrence, location, and relation to rock bursting and production blasting. Approximately 150 seismic events with -0.5 = M = 2.9 were located within the mine, yielding a b value (slope of the logarithm of the number of events with magnitude greater than M versus M) of 0.5. Event locations were constrained using a dense underground array of high-frequency accelerometers. Twenty of the surface-recorded events, with 0.5 = M = 2.9, were associated with rock bursts that produced damage requiring at least 1/2 day of cleanup and/or repair. Other possibly hazardous rock bursts, with magnitudes as small as -1.1, were numerous but were not associated with significant structural damage. Approximately 60 pct of the seismic events with M > -0.5 and 75 pct of damaging rock bursts occurred within 45 min of blasting. Estimates of characteristic rupture dimensions for rock bursts with -1.1 = M = 2.9, based on a conventional dislocation shear-slip model of failure, range from 3 to 300 m.

Jan 1, 2010

By H P. Rossmanith

This contribution addresses the advanced blasting technology which is based on wave propagation theory and fracture mechanics. The new concept of sonicity and the principle of maximizing sonicity in blasting as well as the energy or work of a blast operation will be introduced. It is shown that - in contrast to common belief – it is not the velocity of detonation which controls the blast but the relationship between velocity of detonation and the wave speeds, in other words, the Mach numbers of the blast operation. Based on numerous practical blasts in Germany, the authors show that, when using wave dynamic concepts, there is a linear relationship between peak particle velocity and the work of a blast operation and this linear relationship is controlled by the sonicity of the blast. Extensions to layered and faulted rock masses are presented. It will become clear that a second change of paradigm is enforced, the first one being the implementation of short time delaying. Again, the acquisition of knowledge in wave progation theory and fracture mechanics becomes mandatory in advanced blasting technology, where the art of blasting is now fully transformed into a science of blasting with little room for methods of trial and error.

Jan 1, 2010

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By M J. Daniel

The diamond industry is no newcomer to High Pressure Grinding Rolls (HPGR) as it has used the technology for more than 20 years, predominantly in secondary crushing and recrushing roles. In fact it could be argued that the diamond industry has led the way for the wider minerals industry to consider its application. In existing conventional secondary cone crushing applications, large valuable diamonds are" won" through meticulously managing the recovery process within defined particle size ranges. Conventional crushers operate with relatively large closed side settings, but have the potential to damage diamonds by making direct contact with the sides of the crusher. Cone crushers also result in steep product size distributions that run a high risk of losing many of the smaller, unliberated but more abundant diamonds from the rock. This current comminution paradigm of particle size reduction management results in recrushing processing applications or plants where HPGRs are often used.

Jan 1, 2010

By Ashley Haslett

A European Directive on Identification & Traceability of explosives came into effect on the 4th of April 2008. This directive is intended to establish a harmonised system for the unique identification and traceability of all packaged explosives, detonators, reels of detonating cord and primers used in civil applications across the European Union. The directive must be adopted into the national legislation of each European Union member state by the 5th of April 2009 with compliance achieved throughout Europe by the 5th of April 2012. The requirements of the Directive apply to all explosives manufactured, used and imported into the European Union from 5th April 2012.

Jan 1, 2010

By A. Tarigan

The integration of the ESZ orebody and DOZ orebody resulted in a much larger footprint than the original DOZ Mine shape. The significant change in footprint geometry presented new cave front management challenges, specifically: longer undercut drifts. Using a constant blasting rate, more time is required to complete caving in each drift which ultimately influences the number of active faces at any point in time. The number of manageable active drifts is controlled by the planned square-meters of undercut blasting, lead/lag restrictions and other specific conditions such as the need to blast pre-charged explosives. In early 2008, an evaluation of the existing plan showed that significantly more active undercut drifts and longer cave fronts would occur in the next five years. Difficulties associated with the long cave fronts led to a decision to redesign the caving sequence. Several different boundary options based on operational, geotechnical and ore grade parameters were investigated. This paper describes the issues faced with long cave fronts, the constraints and requirements to effectively manage the caving sequence and the options considered to mitigate this situation.

Jan 1, 2010

By Thomas L. Vandergrift

To significantly increase the stability of underground excavations while exploiting the full advantages of confined rock strength, methods must be developed to actively control the distribution of stresses near the excavation. This U.S. Bureau of Mines study examines theoretical and practical aspects of rock pres¬surization, an active stress control concept that induces compressive stress in the wall rock through repeated hydraulic fracturing with a settable fluid. Numerical analyses performed by incorporating the rock pressurization concept into a variety of boundary-element models indicate that rock pressurization has the potential to improve underground excavation stability in three ways: (1) by relocating stress concentrations away from the weak opening surface to stronger, confined wall rock; (2) by inducing additional stresses in a biaxial stress field to reduce the difference between the principal stress components near the surface of the opening; and (3) by counteracting the tensile stresses induced in the rock around internally loaded openings. Practical aspects of the rock pressurization concept were investigated through a series of hydraulic fracturing experiments. The use of sulfur as a settable fluid for hydraulic fracturing was demonstrated, although problems related to sulfur viscosity suggest that other molten materials, such as wax, may be better suited to practical field application of the rock pressurization concept.

Jan 1, 2010

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

Compagnie Minière Espérance mines a primary gold orebody in an openpit. The ore is processed through crushing, primary gravity concentration, grinding and secondary gravity separation, generating tailings with remaining fine gold. Analysis of the material in the pond has indicated a residual gold grade sufficient to justify a chemical treatment process to recover the gold. However, direct cyanidation would require a prohibitively large installation for the site, which is located in a remote rainforest environment. It was decided to test the feasibility of preconcentration using flotation. As lab tests proved up the technical feasibility of the flotation process, an on-site pilot operation was carried out to assess the continuous circuit performances, define the best configuration and obtain enough data for industrial circuit sizing. Data collected during the pilot campaign was used for calibrating a process simulator built with the USIM? PAC software. The simulator validated the feasibility of upgrading the existing plant, including the reprocessing of tailings to obtain an acceptable fine gold recovery from a small amount of concentrate.

Jan 1, 2010

By Fred C. Turin

The U.S. Bureau of Mines conducted a human factors analysis of hazards associated with roofholting activities in underground coal mines. Emphasis was placed on hazards related to the movement of the drill-head boom or mast of a roof bolting machine. The objective was to identify hazards and recommend solutions. The data-collection effort consisted of analysis of U.S. Mine Safety and Health Ad-ministration accident data; visits to underground mines and interviews with experienced roof bolting machine operators; discussions with roof bolting machine manufacturers; interviews with workers injured while performing roof bolting tasks; and reviews of research on roof bolting safety. A set of recommendations to increase the safety of roof bolting operations was developed. In particular, the following list of recommendations was presented in ranking order: (1) use an interlock device to cut off power to controls when an operator is out of position, (2) place fixed barriers at pinch points, (3) provide appropriate control guarding, (4) reduce fast-feed speed, (5) use automatic cutoff switches at pinch points, (6) redesign control bank to conform to accepted ergonomic principles, and (7) use resin insertion tools and resin cartridge retainers.

Jan 1, 2010

By M. Ye. Melnikov

The report is about oceanic ferromanganese crusts ? covers of iron and manganese hydroxides developed over an opened rock of seamounts and rises. Ore bed parameters of crusts are understandable as their thickness and content of main economic components ? manganese, cobalt and nickel. All known results of research activity on ferromanganese manganese crusts point to that crust are characterized by notable variability of thicknesses and composition. It is possible to separate few levels of variability. The most evident is the first level of parameters variability, which is manifested in various regions of the Ocean, and connected first of all, with an age of submarine mountains, a host objects for a crusts. It was proved by many authors, that most powerful crusts are connected with submarine mountains of Cretaceous age. [1]. Crust thickness at the Magellan Seamounts reaches, for example 12-15 cm, sometimes exceeds 20-22 cm. Thicknesses of Hawaii Archipelago or Tuamotu crusts in 3-4 times less. Biostratigraphy studies of crustal sections at the Magellan Seamounts already show, that its main part started to form in the Late Paleocene. Four layers with well expressed features in structure and composition of a layer are separated in the section. From foot to top: Late Paleocene ? Early Eocene layer I-1, Middle-Late-Eocene layer I-2, Miocene layer II and Pliocene ? Quaternary layer III. Relics of more ancient Campanian ? Maastrichtian ore layer [2, 4] were discovered. It is evident for example, that Oligocene mountains could not be a host for two lower layers in the crust section.

Jan 1, 2010

By S. M. Moore

Each year more than 400 coal miners are injured (fatally and nonfatally) by rock falling from between or around roof supports. Many of these injuries can be prevented by the installation of roof screen. However, many coal mines are reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential savings in workers' compensation (W C) premiums that can be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by Illinois and Kentucky were investigated in this study. Using data obtained from the Mine Safety and Health Administration, national and state WC bodies and individual insurance companies (e.g., average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), baseline mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state's actual WC rate-setting formulas, a sensitivity analysis was conducted to determine the total savings in WC costs after a three-year period. Annual savings in WC premiums ranged from $41,000 to $326,000 for the 67-person mine, and $96,000 to $843,000 for the 150-person mine. An economic analysis of the cost of a roof screening program at a 67-person mine was also conducted. The annual cost of a roof screening program here was estimated at $240,000. At this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By J. E. Nesset

"Significant progress has been made over the past few years on characterizing and understanding the hydrodynamic properties of frothers and collectors and their effect on flotation performance. This new understanding of the relationship between chemistry and hydrodynamics has dramatic implications for how flotation circuits should be controlled and optimized. Previous work has shown that choosing a frother of the right ‘strength’ is critical to the optimization process, and the work and discussion presented here serve to strengthen the argument. In addition, we know that collector chemistry will also influence hydrodynamic properties and needs to be taken into consideration. To achieve the desired outcome, the overall system of reagents and operating parameters must be considered. This paper describes and discusses some of the findings from recent research on frother and collector chemistry effects (on hydrodynamics), and how this knowledge can be used to improve flotation performance. Examples from plant experience are discussed.INTRODUCTIONFrothers perform various functions in flotation but the primary ones are control of bubble size in the pulp zone and stabilization of the froth zone. Laskowski (2003) was among the first to try to capture both roles in characterizing frothers in order to provide a basis for frother selection for a given duty, as well as to explore the link between function and frother chemistry (structure). The method he used requires bubble size data and a frothing index; the procedure has been simplified by Cappuccitti and Finch (2008) using gas hold-up to substitute for bubble size, and froth height (without overflow) as the froth stability metric. The gas hold-up/froth height relationship will be referred to as ‘hydrodynamic characterization’. Essentially, the gas hold-up parameter reflects the sum of the hydrodynamic conditions in the pulp phase (water in this case), i.e. the effect of bubble size plus the apparent impact of the water surrounding the bubble due to the frother (Finch, Nesset and Acuna, 2008). Similarly, the stable froth height parameter reflects the sum of hydrodynamic conditions in the froth, i.e. the effect of bubble size undergoing coalescence plus the influence of the water in the lamellae and Plateau borders between bubbles. It could be argued that the gas hold-up/froth height relationship is a superior one to simple bubble size/froth index for discerning differences in frother behaviour"

Jan 1, 2010

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By A. J. Teske

Sustainable Development is a very broad initiative in the mining industry, with major components running over the entire life of the mine. It likely commences with pre-exploration permitting and continues to post-mining final closure and possible land reuse. Most major mining corporations embrace the sustainability initiative, either out of a sense of social responsibility or out of necessity in order to continue doing business. But many may view the overall initiative as an added ?cost of doing business.? In many elements of sustainability, there clearly can be added cost ? some as simple as complying with self-imposed sustainability reporting. Fortunately, one major element of sustainable development can clearly be shown to reduce costs ? energy resource management. This paper will describe how the mining industry sustainable development effort differs from other industries, but can benefit from their experience in energy resource management. The mining industry can utilize proven methods from other industries to further their energy management efforts. In addition, many of the resources developed and employed to promote better energy resource management in non-mining industrial settings will be listed.

Jan 1, 2010

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010