Search Documents

By X. Shi

Magnesium, the lightest structural metal, has not yet been considered as a serious contestant for automotive use due to its weaknesses in corrosion. Electroless nickel-boron alloys are well known for their corrosion resistance and hardness. An electroless nickel-boron layer was successfully deposited first on the chemical conversion pre-treated AZ31 alloy and also on the Ni-P coating which was deposited on the conversion coating. The electroless bath contained nickel sulphate and dimethylamine borane (DMAB) as main salts and the samples were activated by a 5 g/L AgNO3 solution before the electroless plating process. The presence of the conversion coating between the nickel coating and the AZ31 substrate acted as a barrier and prevented corrosion of the alloy. The morphology of the nickel-boron layer was studied using SEM. The crystal structure and the composition were examined by EDS and the hardness was measured. The corrosion behaviour of the nickel-boron layer deposited on the conversion coating and on the Ni-P coating was studied using potentiodynamic polarization in a 0.5M NaC1 solution. A saturated standard calomel electrode was used as a reference electrode. The results show that the nickel-boron coatings had a significantly better corrosion resistance than the AZ31.

Jan 1, 2006

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

Mining is a global industry. The conference is a good example of this, as itÆs jointly organised by professional associations from Canada, Australia and South Africa, and has attracted speakers and delegates from around the world. I commend the organisers for their initiative. I am pleased to be asked to participate in this panel û although I would hasten to add I see myself as perhaps an informed observer rather than an expert. It wonÆt be news to most in this room that AustraliaÆs mining sector is booming. As one of the most productive and diversified mineral regions in the world, this activity is also something that has not escaped the attention of CanadaÆs largest mining companies! This means that I follow what is happening in the industry and more specifically what might be occurring here. Two-way investment between Canada and Australia stood at $9.8 billion in 2005 with Canada as the seventh largest overall investor in Australia with $8.22 billion in investments. The majority of this investment is by Canadian minerals and metals companies. In recognition of the importance of Canadian investment in this sector in Australia, I maintain close contact with our companies. By way of example, in the past two months I spent a week in Western Australia visiting Perth and meeting with companies for example, like Teck Cominco and LionOre as well as seeing various Barrick Gold operations in Kalgoorlie. I attended the opening of AlcanÆs new Asia Pacific Headquarters in Brisbane in August and just two weeks ago was in Cowal, NSW for the opening of BarrickÆs new mine there. Having met with BHP Billiton in Vancouver, IÆm equally aware of active Australian mining interests in Canada. This is not designed to indicate how active I am but rather to demonstrate the dynamism in the mining industry and the diversity of Canadian mining interests in this country and Australian interests in Canada.

Jan 1, 2006

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By Pierre Gratton, Gordon Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM’s goal is to improve the mining industry’s performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move to external verification of their performance in 2006. The presentation will describe the initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector.

Jan 1, 2006

By Claude Bazin

"Laboratory semi-batch flotation tests were conducted using two different sulphide ore samples. The size reduction was adjusted to cover a wide range of flotation feed size distributions. Results show that similar recoveries can be achieved independently of the fineness of grind. This result suggests that possible energy savings could be achieved by a redistribution of the power between the grinding and regrinding mills. The behaviour of the selectivity curves shows that some gangue minerals are more sensitive to particle size than other ones, implying the existence of preferential associations between minerals in the ore.INTRODUCTIONInteractions between grinding and flotation have been studied for many years, and still a robust model to link the two processes lacks to be developed (Girard et al., 2005; Bazin et al., 2001). The ore size reduction liberates mineral grains, while flotation separates them into valuable minerals and gangue. The more size reduction that is applied to the ore the more important is the mineral liberation but also the production of fine particles that can pose problems during flotation (Trahar and Warren, 1976). The definition of the grinding requirement for flotation is a complex problem (Rickelton and Dell, 1977; Sosa Blanca et al., 2000; Morrison, 1993; Wei and Gay, 1999).This paper analyzes the effect of the fineness of grind using semi-batch flotation test results. The first two sections describe the test procedure and the results. The third section analyzes the results in terms of liberation and selectivity, and proposes a possible redistribution of power between grinding and regrinding mills."

Jan 1, 2006

By L. S. Almeida, U. A. Courbassier, C. T. Guimãaraes, M. N. Souza, V. L. Silva, H. P. Dias, G. A. Bicalho, B. S. Rocha, P. N. Rodrigues, A. Carnevale

During primary aluminum production the anode changing is a very important task. So improvements on it will be essential to avoid disturbance and have a better operational control. After anode changing a good current distribution will be guaranteed using a cavity cleaner and precise anode setting. Albras switching a manually anode setting to an automatic one solved the setting problems. In this paper it will be shown some pot line results and the improvements on workers ergonomic and safety conditions. The device was developed in a partnership between Albras and Pesto.

Jan 1, 2006

By Z. Farhat

In spite of advances in cutting tool technology, the understanding of the basic wear behavior and failure mechanisms needs further study. Tool wear is the main factor contributing to geometrical error and thermal damage in machined components. Manifested as a reduction in tool life, it also affects the workpiece surface finish, increases cutting forces and induces residual stresses. Furthermore, the emergence of high and ultra-high speed machining processes necessitates the investigation of tool wear under these severe working conditions. Tungsten carbide-cobalt composite material has been used traditionally as wear resistant materials for many years. One main application of this material is in cutting tools. WC-Co tools consist of hard WC particles imbedded in a tough Co matrix, which functions as a binder phase. More recently, Cubic boron nitride (CBN) tool material have attracted special attention due to its high hardness and excellent wear resistance. Boron nitride in its cubic form is known to be the hardest material next only to diamond. In this paper microstructural and tribological properties of commercial grade WC-Co and CBN cutting tool materials are investigated under high speed cutting conditions. The CBN cutting tools were found to be superior to tungsten carbide (WC) tools. Four-fold increase in productivity and significant reduction in chipping and cratering was achieved for CBN as compared to WC. Wear mechanisms are proposed and are related to the observed wear characteristics in the cutting zone.

Jan 1, 2006

By M Field

Kimberlite pipes, as opposed to dykes, sill and secondary deposits, are the primary target for diamond exploration companies because they have simple geometries and can contain large volumes of potentially diamond-bearing ore. Once discovered, important decisions have to be made regarding the sampling of these geological entities to establish the total volume of ore present, and to define the internal geology, which can be complex in nature and controls the distribution of diamond grade. It is essential that as part of this process the uncertainty in constructed geological models are assessed. In this paper the Orapa AK1 kimberlite pipe in Botswana is used as a case study to explore a potential methodology for defining this uncertainty. The uncertainty of the rock volumes of different types can be characterised by a geostatistical approach. Geostatistical simulations, based upon a plausible representation of the geological bodies, provide different possible images of the orebody that can be considered as different realities. By testing different borehole layouts and drilling the orebody virtually on the computer, many different, but equi-probable realisations of the pipes can be produced. It is then possible to estimate the rocksÆ volumes and compare them with the actual ones. A statistical analysis of the relationship between estimation error and the number of boreholes can then be used to optimise the next sampling campaign. The rock volumes are obtained from a two-step simulation process. Firstly, the pipe geometry is simulated by means of introducing variations around the geological block model, by an original method called centre point simulation (CPS), which has been developed for this purpose. Secondly, the internal geology is then simulated within the pipe. The methodology for simulating the internal geological zones has to be adapted to the level of information and to the geological structure itself. The upper portion at Orapa AK1 is filled with sedimentary crater facies. Here plurigaussian simulation techniques can be applied that are adapted to the simulation of sedimentary facies. The central zones of the pipe are typically subvertically-oriented massive volcaniclastic deposits and breccias and the lower regions comprise a complex root zone. CPS is appropriate for these zones.

Jan 1, 2006

This paper is for mine managers. It is about maintenance of mining equipment. This is an extremely broad subject so this paper is given with the caveat that it necessarily contains generalisations, not true in all cases, but broadly correct. The job of mine managers is to be good at making money from the excavation and preliminary treatment of mineral. To do this well, they need to understand the cost and value drivers in the business. This includes understanding the drivers associated with maintenance. Maintenance is often identified as a problem at mine sites. It is frequently listed as the cause of production shortfalls when reporting. The state of maintenance within mining as an industry is generally among the lower end of the range, when compared to manufacturing, petrochemicals, etc. Why is this? Experience and review of many audits and evaluations of maintenance has shown that some patterns are consistent with good performance and some consistent with poor performance. These often centre around the time horizon of the management team and are associated with knowing the sensitivity of the business to certain maintenance drivers and the mechanisms of maintenance and their results. To summarise, some common misunderstandings can be listed as statements that are obvious and extrapolations from those, which are not necessarily correct. For example: High availability of equipment is necessary for production. Incorrect extrapolation:focus on availability will produce high production. Design is often the greatest factor in determining the reliability of a mining machine. Incorrect extrapolation: the newest and biggest machines generally have the lowest cost operations. Operation has an enormous impact on machine productivity and reliability. Incorrect extrapolation: the fastest operators are generally the best from a productive point of view. Some maintenance improves the performance and reliability of machines. Incorrect extrapolation: more maintenance will give you more reliability. Some maintenance depends on disassembly and reassembly of components. Incorrect extrapolation: assembly is basically the reverse process of disassembly. Maintenance improvement in the mining industry in the last 15 years has focused largely on planning and systems improvement. Incorrect extrapolation: most of the problems in maintenance can be traced to a lack of planning. Actions based on flawed extrapolations will steer a business suboptimally. It is therefore important that the mine manager understands these issues so that the improvement effort can be directed to the greatest benefit.

Jan 1, 2006

By G. Barrasso

REACH was proposed by the EU Commission in October 2003 and stands for the Registration Evaluation, Authorisation and Restriction of Chemicals. It requires that all substances identified as persistent, bio-accumulative and toxic, whether the risk of those chemicals being released is real or perceived, require registration prior to them being allowed to be imported into the European Union. An internal investigation by the metals industry indicates that almost all primary raw materials streams would be classified as hazardous due to the potential health or environmental hazard properties of one or more of their ingredients. REACH uses a wide definition for chemicals and metals and as such its implications greatly impact the entire supply chain of the metals industry. The process of registration would require the producer/ importer to produce a dossier. Initiatives along the same lines as the EU REACH are also coming up in other parts of the world. REACH requires registration of at least four substances manufactured by the aluminium industry: aluminium metal, including powder, aluminium oxide, and aluminium hydroxide. The proposed legislation permits the affected companies to band together to form a consortium to develop certain aspects of the registration application. The aluminium industry has established a consortium and testing is currently underway.

Jan 1, 2006

By Maurice Bottiau

It is a quite challenging objective to aim at covering in one paper the most recent evolution in piling and deep foundations technologies. This report has to be understood within the limits of the session 2b. It will therefore concentrate on the technological evolution of deep foundation techniques, addressing design issues only when directly related to execution aspects. For the same reason, it will not address the related codes, as a separate session of this conference is specifically dedicated to this topic. Monitoring and deep excavations being covered in other sessions, they will only be addressed when clearly relevant. We will try to show, from a practical viewpoint what are the main changes and the most exciting or critical issues over the last years, as they appear from the topics addressed in the literature or in the papers published in this session of the conference. As the paper mostly intends to explain trends and critical topics, it cannot be exhaustive, neither can it give the full description of the case studies. The author invites the reader to read the full papers, for a more complete description. We have divided our report in three main topics: Piling, soil improvement and treatment and retaining walls. Anchors and tie-backs will not be treated, neither tunneling.

Jan 1, 2006

In the pursuit of commercial solutions for environmental issues, individual problems are often identified, considered and resolved in isolation from other environmental matters and always at the end of the cycle û after the problem has been created. Inter-relationships are neglected if they are not seen to obviously impact on a specific problem and the issue at hand is plucked from the environmental landscape and dealt with in total isolation to all else. In a Zero Waste approach to environmental matters, all outputs are pursued as potential inputs. Industrial processes are viewed as a variation on natureÆs theme and opportunity pursued above all else. When viewed from this perspective, industry appears to have forgotten its origins. It has forgotten that it is principally about people. The juggernaut of global trade has forgotten that it is a small part of a big landscape and that its principal participants, people, cannot exist without healthy soil. Commercial activity in all parts of the world relies heavily on the ability of agriculture to produce the necessary inputs for industrial production. The care and nurturing of our soils is fundamental, not only to the survival of humanity, but also to the economic systems that support that humanity and to the industry which profits by it. Actual levels of domestic recycling in many countries around the world seldom reflect the 90 plus per cent desire to recycle recorded in surveys conducted by local authorities in almost every country. If the desire to recycle is far removed from the end result, why is it that the systems provided are so ineffective? It is obvious that what we do need is a recycling system that both engages and rewards the participant and stimulates the innate desire to support the environment. A recent trial in New South Wales, Australia, demonstrated that by giving individual households credits for recycling organic wastes, not only will contamination levels fall dramatically, but increased yields, improved soil structure, improved land values, reduced fertiliser costs and increased water use efficiency give the farmer good economic reasons for purchasing and applying quality composted product. By underpinning and securing the agricultural community, we secure the future of industry. The æCity to SoilÆ project linked the economic on-farm benefits of compost use with reduced contamination through the provision of rewards paid for by the purchase of product by the farmer.

Jan 1, 2006

By Paul Downing

Identity Theft Outline • What Are MY Chances??? • Types Of Thefts • Sources Of Theft Info • Stolen Identity vs. Background Checks • Information/Data Safeguards • Corporate Data Handling • Reclaiming Your Identity • Monitoring Your Identity

Jan 1, 2006

By S Wright, W Bruckard

The current status of battery collection and recycling schemes in Australia are explored in light of current developments in product stewardship and increasing pressure to decrease materials going to landfill by originating equipment manufacturers. Used consumer batteries, both single cycle and rechargeable contain a mixture of valuable metals and potentially toxic materials that may become a resource/revenue stream to offset the cost of disposal/recycling. Although the volume of batteries discarded in Australia is modest compared to other global population centres, the expected increase in battery use with increasing equipment portability and future developments in the automotive industry, provide an opportunity to recycle. The requirements for a battery recycling facility in Australia and the most promising processing platforms that may exploit the resource with enough flexibility to cope with battery developments and market trends, are explored.

Jan 1, 2006

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By Klaus Gamweger

There are different reasons for purging a metal bath. The operations are varied, for example the purging gas can be used as a reactive gas being part of the metallurgical process or as an inert gas using the rising gas bubbles for agitation only. The different purposes for agitation, chemical and thermal homogenization or a preferential movement of the slag to the slag skimming door have to be considered. It depends on the furnace type and its dimensions as well as the process characteristics what the focus is on. For an optimized arrangement of numbers and position of all single plugs in the furnace, mathematical modeling - the CFD Computational Fluid Dynamics method - is used. This paper shows how the operation of purging plugs can influence the metallurgical process of an anode furnace by the example of Jinchuan Copper in China. The potentials for savings in energy consumption as well as in time for oxidation and reduction are presented.

Jan 1, 2006

By E Hondros

Innovation and Business Skills Australia (IBSA) commissioned The Boston Consulting Group (BCG) to undertake a study into how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. This report builds on a previous study prepared by BCG in the early 1990s for the Industry Taskforce on Leadership and Management Skills (Karpin Committee), which provided a snapshot of the Senior Manager in 2010. The following powerpoint slides summarise the 2020 Vision û The Manager of the 21st Century û outlining how the role of AustraliaÆs senior managers is likely to change between now and 2020 and to identify the skills and attributes that will be needed to respond to those changes. The presentation is summed up in the following quote from Jon Nicholson û Senior Vice President of BCG: We believe that to succeed in the years up to 2020, executives will need to master a range of hard and soft skills. Amongst other things, they will require to manage multi-generaional teams, the creativity to measure staff performance on outputs rather than inputs, and a high degree of technical and functional expertise in addition to their general management credentials. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

The mine manager is one of the oldest jobs in the world. Over many centuries the fundamentals of how this job was approached did not change much. However since the later part of the 1980s there has been a dramatic shift in the expectations and role of the mine manager as the pressures of globalisation and consolidation have increased the size of companies and the production levels of mining operations. The changes have been dramatic, with demanding requirements on mine managers to continually improve the skill levels of people, to apply and develop rapidly changing technologies and to consider far broader business issues that need to be managed in a truly globally connected world. This paper will attempt to outline some of the issues, the complexity surrounding them and some of the approaches that have been made to manage them. There is not a single correct answer or approach, but there are many key success factors that have led to some amazing levels of performance being achieved as we go deeper, broader and literally move mountains to meet the customerÆs needs for today and tomorrow. This contrasts with many mining operations in developing countries that still have a traditional approach to how they mine. Society is the river of life that continually flows and changes the environment that surrounds it. The pressures from the customers and world growth, shape and force alterations to be made in an industry that has to live with the far greater primal and uncompromising forces of the earth we mine. This has led to some paradigm shifts in how we accept what we manage. TodayÆs mine manager must manage a far broader range of issues, than just how do we get tonnage out of the mine and product out of the ore. These include but are not limited to technical, commercial, product quality and end use understanding, employee and community issues, environmental and the ever increasing complexities of sustainable development. Organisations will have to look at how they structure their management of the business to manage functions to meet the complexity of different stakeholders needs û the business, the employees, the customer and the broader community within an environment that is becoming more attuned to the harm impacts to the world in which we operate. The attraction and retention of skilled people that contribute to the value and worth of the corporation, will become critical to sustain a companyÆs growth. One of the fundamental elements of successfully doing this will always be the skills of the mine manager and his/her extended team with the continued development and support that they will need to meet these demands.

Jan 1, 2006