Search Documents

By L. Adler

INTRODUCTION The purpose of this paper is to describe in engineering terms the singular and basic operational kinematics of all excavating and bulk handling equipment. The safe and efficient use of equipment will be fostered by enabling the engineer to conceptually duplicate the operators' "tasks" in directing and controlling it. A simple graphical and notational scheme will be introduced to define the essential gross repetitive motions. The significance of this effort includes filling a vital analytical gap at the work face, and in establishing direct communications between the engineer and equipment operator. Since all types and sizes of earth- moving equipment are covered, a major concern has been to integrate equipment specialties into d single encompassing discipline. Equipment types are closely related to the working conditions, and their selection and evaluation are also considered. The extension to human factors analysis is natural and predictable. Since human [actors are involved, the operational analysis can also be considered a catch-all for many subtle vagaries. BACKGROUND Symbolic modelling linked to a notational system will be developed and intensively used. This constitutes the "language of science," providing a shorthand method which gives immediate recognition, is fluent, explicit, reinforcing, unequivocal and provides limitless associations. Many examples of symbolic modelling exist in chemistry, physics, the military, engineering sciences and it is a major tool in mapping. Its use is so ubiquitous that it often goes unnoticed. On the other hand it must be realized that something is lost in simplifying and idealizing what is an extraordinarily complex occurrence. The components describing the basic operational kinematics of equipment include: (1) the vehicular motions as a rigid body and (2) the job-end motions focussing on excavating (Adler, 1985). These provide all of the components in the load-haul-dump sequence (L-H-D) , and will yield three dimensional expressions. Complex patterns can also be assembled from these simple elements. An existing equipment designation employed in earthmoving will be integrated into this approach (Carson, 1961). Along with the basic motions, corresponding working conditions will be noted.

Jan 1, 1986

By B. A. Massey

Sooner or later, we'll encounter a subordinate, peer, or boss that will test our management skills to the limit. The chances are good that our formal educations have not fully prepared us to effectively handle the situation, and through trial-by-fire, we have learned that the management of people is often as much an art as it is a science. Assertiveness - as opposed to agressiveness - is basically positive persuation. Assertive management techniques can help combine the art and science of managment to sell ideas, accomplish goals, direct the workforce, and generally promote the corporate - as well as our own - objectives

Jan 1, 1986

By Reynolds JO

This contribution by. The Australasian Institute of Mining and Metallurgy has three main thrusts. First, an Institute (and industry) view on academia and the need for more entrepreneurship at top academic levels, second the need to lift our technological game, and third, professionalism and the perceived role of mineral industry education. While I will deal with each of these separately they are of course inter- related and can be brought together under the frequently used, but insufficiently practised title, "communications". First then, The Institute and industry view of academia. There are some academics in the audience and I imagine they may wish to reply to my remarks with an academic view of industry. That is not unreasonable. Like all human institutions, academic institutions vary in quality and characteristics. Some are successful and some less so. Some historically are well renowned. Others that were once successful schools have declined. Lesser known schools have grown into prominence. What is it that sets apart 'good' highly regarded schools from those that are not so well regarded? It comes down to one main ingredient - "leadership". The strong mining schools in the past 100 years have been strong because they have had outstanding and clearly identified leaders. Strong clearly identified leadership has always had rapport with, and the support of the industry. The two go hand- in-hand, each nourishing and supporting the Other.

Jan 1, 1986

In some 35 years in the explosive and construction industries, we have probably seen the extremes in drilling and blasting practices. All of you know that it is difficult if not impossible, to separate those two operations, particularly when we are searching for an optimum. Early in my career while doing engineering survey work for a major cross country pipeline construction company, we witnessed some of the wildest blasts imaginable, and they were wild for two reasons. Both the drill hole diameter and the drill pattern were such that when loaded with explosives, the factor in terms of pounds/cu. yd. was extremely high. On the other hand, in 1982 we were in an underground coal mine where just one hole was used to prepare a 20-ft. (6m) wide face. In this coal mine, they brought down 7 yd3 (5.35m3) of coal with just 1 lb. (.454 kg) of explosive. On a pipeline job, the factor may only be .1 yd3 per lb. of explosives. Open pit operations in the same geographical area may have almost the same type of rock, but similarities could end there. The several operators over the years will have installed different size-crushing equipment or variances will exist in other facets such as drilling, excavating, and haulage units. That tells us that if we have 6 operations in that common area, we are faced with a fact that there is an optimum drilling and blasting pattern for each of those six. We start at that point. We will note from Figure No. 2 the simple equations for determining either cu. yds. or tons. For a rock heavier than limestone, it may require only 10 to 11 cu. ft. (.31m3) for 1 ton (.91 metric ton) of rock in place.

Jan 1, 1986

Mineral policy is now generally regarded as a function reserved to government. Government is reponsible for the economic health and progress of nations, and must therefore interest itself in minerals as a basic national resource. Government should therefore identify objectives which it sees as suitable and necessary for the mineral industry so that the industry can play its part in achieving national goals. It should provide the legislative framework and policy guidelines to enable these objectives to be achieved. The essential objective of a national mineral policy should be rational development of the nation's minerals resources. To achieve this, it need not be too formal; broad guidelines are enough. But it must be dynamic, to keep pace with the changing circumstances of the mineral industry in the world scene and the changing requirements of government. It should be flexible, recognising that there is no such thing as a "typical" mineral deposit; above all it should represent the outcome of a continuing dialogue between government and industry. Both government policy and corporate planning need to be formulated on the practical understanding of the potential economic value of the mineral sector and what it can contribute to the nation's prosperity. There needs to be a common understanding of the wide range of the costs of risks that may arise through the exploration and development stages and of the uncertainties affecting ventures at the production stage. There needs to be a common understanding that the size and importance of the mineral sector is determined in the long run by the level of investment in exploration. The development of a continuing understanding between government and industry should lead to the formulation of ground rules which ensure the continuance of a strong industry able to adapt to the changing world scene and make its contribution to national growth and wellbeing.

Jan 1, 1986

By Levent Ozdemir

The results of a laboratory research program aimed at the development of a water jet assisted drag bit cutting system for coal mine applications are presented. Two types of drag bits, a conical and a plow bit, were tested in a hard sandstone rock with jet pressures of up to 20,000 psi. Jet locations investigated were in-front and behind the bit. For each jet mounting location, three jet impingement distances with respect to bit tip were tested. The closest jet impingement location to bit tip was found most effective, providing the greatest force reductions on the bit. Overall, significant bit force reductions up to 50 percent were obtained with jet assist. Also observed was a drastic reduction in airborne dust when jets were employed.

Jan 1, 1986

By Vas Choudhry

INTRODUCTION Traditionally mineral processing equipment has been procured based on (equipment) specifications prepared by the engineers. As newer materials of construction are being used for equipment manufacture and plant control systems become more sophisticated, the need for thorough and detailed specifications is greater than ever. For example, it is not uncommon to find plants looking at grinding circuits consisting of semiautogenous mills with variable speed, gearless, drives of large horsepower. Technical specifications for the mill, wrap- around motor and control system must, therefore, be carefully prepared to ensure that the respective equipment supplied by vendors meets overall grinding needs. Various engineering and design companies have expended considerable time and effort in developing the specification format. Equipment manufacturers have also given significant effort to developing data sheets aimed at collecting information regarding not only the duty of the equipment, but also the conditions under which it will be operated. As engineers moved from one company to another, the specification format became cross-fertilized and further developed. As a result, specifications on file with various engineers have improved considerably over a period of time. Equipment specifications from earlier projects are commonly used as a basis for tailoring new ones. To keep equipment specifications short, general technical considerations are often compiled as separate specifications. For example, general considerations applicable to the design, manufacture and supply of the mechanical equipment are consolidated under "Standard Requirements for Mechanical Equipment” and included along with that specified for purchase. As the economic feasibility of the project has been established during earlier studies, purchase-related activities can be initiated following completion of the specifications. Procurement itself is a major activity, however, in this chapter only those activities directly related to the purchase of equipment will be discussed. PREPARING EQUIPMENT SPECIFICTION Specification for process equipment or machinery is written in such a way as to define exactly what is required of the equipment. Generally, mechanical

Jan 1, 1986

By M. Moss Stanley, Ronald P. Klepper

The objective of this chapter is to provide data that will assist in the selection and sizing of equipment utilized in the filtration method of separating solids from liquids. It should be recognized at the outset that in some situations more than one option may be available to achieve the target desired. In some cases purely technical objectives may be sacrificed because of cost considerations, design factors or other elements in order to satisfy optimization within the flowsheet and/or to provide bottom line results. Before considering available options, and prior to the next step of sizing out the selection, the operating criteria should be set down. The test work to develop selection and sizing data will be based on this data and the final products desired. This will help to establish initial parameters. A. GENERAL DATA 1. Material to be filtered: a. Solids b. Mother liquor 2. Feed rate of slurry in GPM 3. Density of slurry: Sp. Gr. Solids 4. Slurry: Temp. pH Viscosity 5. Source and method of feed 6. Valuable product: Solids Filtrate Both 7. Details on: Volatility Toxicity Stability 8. If flocculant is indicated, what has been used? 9. Describe product: (i.e., fibrous, cor 10. rosive, abrasive, inflammable, explosive, pasty, 11. Does product alter or require special environment during transport? 12. What type of filter media has been used successfully? 13. Is there any objection to use of a filter aid? If not, is there any preference? B. SOLIDS DATA 1. Sp. Gr. Bulk density 2. Screen analysis 3. Desired percentage moisture in cake 4. Solubility (state conditions): In mother liquor In wash water 5. Description of cake: (i.e., amorphous, fibrous, crystalline, colloidal, gran¬ular, thixotropic, 6. Special requirements for moisture de¬termination? 7. Can solids be compressed during dewatering? 8. Proposed product handling 9. Subsequent thermal drying or other pro¬cedure C. FILTRATE 1. Is separation of wash water and mother liquor desirable?

Jan 1, 1986

THIS SYMPOSIUM ON AUSTRALIAN BEACH SANDS IS MOST TIMELY; WHEN WE ARE APPROACHING PEAK PRODUCTION FROM THESE RESOURCES AND WHEN PRICES ARE GOOD, BUT THE RESOURCES CAN BE SEEN TO BE COMING TO AN END IN THE LIFETIME OF OUR YOUNGER COLLEAGUES - 20 TO 25 YEARS AS WE HEARD FROM ROY TOWNER TODAY. THE SPREAD OF PAPERS HAS BEEN 15 PERCENT EACH ON GEOLOGY AND THE MINERAL RESOURCES, WITH 25 PERCENT ON LAND USE AND ENVIRONMENTAL PROBLEMS. I AM PLEASED TO SEE 20 PERCENT HAS BEEN ON TREATMENT PROCESSES AND 25 PERCENT HAS BEEN CONCERNED WITH DOWNSTREAM USES. I SUSPECT THESE RATIOS ARE DUE IN PART TO THE WAY PAPERS WERE CALLED FOR, BUT THEY ALSO SUMMARISE CLOSELY THE BALANCE OF INTERESTS IN THE INDUSTRY. NOTE AGAIN; 30% CONCERNED WITH SUSTAIN -ING RESOURCES, BUT 25% WATCHING LAND USE AND IMPOSING CONTROLS; 20 % IMPROVING THE PRESENT PROCESSING, AND A HEALTHY 25% WITH AN INTEREST" IN WHAT HAPPENS TO THE MINERAL CONCENTRATES. I SHALL RETURN TO THIS FOURTH POINT AT THE END OF MY REMARKS. THE POSSIBILITY OF ADDITIONAL HEAVY MINERAL SANDS IN NEW AREAS WAS HINTED AT BY M.S. SHEPHERD (EG TERTIARY SHORELINES OF THE MURRAY BASIN). OLD FOSSIL SHORELINES, WELL REMOVED FROM PRESENT SHORES ARE AN IMPORTANT MINERAL SOURCE IN CHINA AND IT WOULD HAVE BEEN INTERESTING TO HEAR FROM THE SEVERAL COMPANIES EXPLORING IN THE MURRAY BASIN. I ALSO NOTICED THAT WHILST OUR MONAZITE

Jan 1, 1986

By B. F. Westfall

Throughout the 1960's and 1970's world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980's shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

In 1981, North American Degerstrom Contracting began gold mining on the Little Rocky Mountain Range, near Zortman, MT. In the past four years, the price of gold has fluctuated from a high of $16/g ($500 per oz) to a low of $9.60/g ($300 per oz). With that kind of a moving target, profitability presents a management challenge. Based in Spokane, WA, Degerstrom employs 85 people at the mine. It is one of the largest heap leach operations in the nation. Last year, 8 Mt (9 million st) of low-grade ore was moved to the leach pads in a two-shift, five-day operation. The current pit being worked produces 218 kt/m (240,000 stpm) of leaching ore. Ore fragmentation critical The gold bearing ore has no defined patterns or seams. It is an igneous intrusion resulting from volcanic activity. It occurs spontaneously throughout the range. To recover the gold, areas are staked out and core samples are taken and analyzed. These data determine if the ore is rich enough to mine. Once mining begins, an average of 150 holes are drilled and blasted on a two-day rotation. Five Ingersoll-Rand T4s drill on a 4- x 4.5-m (14- x 15-ft) spacing to a 7.6-m (25-ft) depth. "When we first came to this site, we drilled on a 3.6- x 3.6-m (12- x 12-ft) pattern," said Paul Baker, superintendent for N.A. Degerstrom Contracting. "We did some experimenting using a high density emulsion in the bottom of the hole and filling the rest with regular Anfo." The high density emulsion saved the company on overall drilling and blasting costs since the holes could be spaced on a wider pattern and still achieve the high degree of fragmentation needed for leaching. Blasting is important because the gold lays in the natural strata of the rock. Also, the ore is not crushed before it goes to the leach pads. So complete fragmentation is critical. Terrain dictates loading/hauling system The shot ore is worked in 6 m (20 ft) benches by two Caterpillar 245 front shovels equipped with 3 m3 (4 cu yd) buckets, a 992C wheel loader with a 12.6-m3 (16.5-cu yd) bucket, and a 988E high lift fed by a D9H. A Caterpillar D10 tractor trap dozes to the loader. According to Baker, the 6 m (20 ft) bench is an efficient lift for the front shovel and the wheel loader. In tight quarters or in a pocket of ore, Degerstrom uses the 245s. For high production areas, the wheel loader is used. The hauling fleet includes 28 Cat 773 off highway trucks. The 45 t (50 st) trucks are seven pass loaded by the 245s with a 25-second cycle time per bucket load. The 992C loads the trucks in two passes in less than 30 seconds. The cycle time is four to five minutes for a 1.2-km (4000-ft) haul on grades that average 10%. Grades, in some places, exceed 16%. "We use the 773s because they have a low weight-to-horsepower ratio - that's what you need in steep country," Baker said. The trucks haul the shot ore to the leach pad. Currently, Degerstrom is working a pad that has a capacity for 5 Mt (5.5 million st) of ore. Building the leach pads The base of the pads resemble a large drainage basin. They take about one month to construct. A 0.3-m (1-ft) layer of impervious bentonite clay is hauled in and leveled by a Cat D9H tractor. A 30-mm (1.2-in.) PVC liner is then laid in place on top of the clay base. It, in turn, is covered with tailings from an old on-site mill. Degerstrom uses the tailings to protect the liner from tears when the ore is dumped. The ore is leveled and built up in 9 m (30 ft) lifts by the D9H. The tractor rips the top layer. Then, a network of plastic irrigation pipe is put in place to distribute a cyanide solution over the surface. The leaching solution percolates through the ore and dissolves the gold. The solution drains from the pads and is pumped to a 22.7-ML (6-million gal) pregnant solution holding pond. The liquid then goes through two separate filtration units. One unit removes entrained solids and the other side adds a zinc dust to precipitate the gold. This is collected on filters. The affluent then returns to a solution holding pond for redistribution through the pipeline network. Typically, 80% of the pad's potential recovery takes place in the first 30 days of leaching. The process stops when the ambient temperature falls below the cyanide's freezing level. And each pad has a leach cycle of four to five years before recovery values decline to a point where further leaching becomes uneconomical. At Zortman, it takes 9 t (10 st) of ore to produce 31 g (1 oz) of gold. It is therefore critical to keep total production costs down and efficiency high.

Jan 1, 1986

By Sunil S. Gandhi

"Uranium occurrences are widely distributed in tuffaceous-argillaceous beds and abundant rhyolitic volcanic rocks of the upper Aillik group, which is more than 3 km thick and over 125 km by 40 km in areal extent. They include partially developed Kitts and Michelin deposits, containing 1560 and 7366 t U respectively.Uranium occurs mainly as disseminated fine pitchblende grains in beds and lenticular stratabound zones, and rarely as coarse pitchblende aggregates and thin veinlets. The Kitts deposit and ten other occurrences are in the argillaceous-tuffaceous beds within a steeply dipping stratigraphic zone, less than 50 m thick and over 20 km long, at the base of the upper Aillik group. The occurrences hosted by the rhyolitic rocks, numbering over fifty and including the Michelin deposit, are in elongate structural-stratigraphic belts or zones, and are characterized by a pronounced enrichment of soda and depletion of potash associated with mineralization. The mineralized zones are affected to a varying degree by Hudsonian deformation, metamorphism and granitic intrusions.The uranium mineralization is interpreted as genetically related to the felsic volcanism, involving syngenetic deposition in argillaceous-tuffaceous beds and epigenetic emplacement in rhyolites. The volcanic activity occurred 1855 ± 5 Ma ago according to a preliminary U-Pb zircon date on porphyritic rhyolite. Pitchblendesfrom the Kitts and Michelin deposits and a few other occurrences in rhyolites have yielded nearly concordant dates in 1810 to 1730 Ma range. They reflect resetting of isotopic equilibrium at the time of Hudsonian deformation. Other isotopic data on pitchblendes and galena from veins and aggregates .in the south near the 'Grenville Front' indicate local redistribution of uranium and radiogenic lead at the time of Grenville Orogeny approximately 1100 Ma ago."

Jan 1, 1986

By H. E. Hirsch

Propelled by the invention of the transistor at Bell Laboratories, germanium's unique properties have advanced our electronic world by many years. Germanium has found major uses in infrared optics, fiber optics and a revised vigor as a catalyst for PET plastic production. Other advanced applications are in various stages of development. The solid state electronics industry has been the driving force behind the accelerating demand for gallium since the late sixties. Past developments of substrates for light emitting diodes, lasers and magnetic bubble memories are paling in view of the current excitement over the use of semi-insulating gallium arsenide for high performance integrated circuits. This application requires gallium metal and gallium compounds of extraordinary purity.

Jan 1, 1986

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By John T. Berry, Robert D. Pehlke, Michael J. Beffel

"Pattern making and metal casting organizations are currently adopting CAD/CAM systems and implementing this technology in design and production. Al though significant progress has been reported, these systems generally are based on two or two and one half dimensional analyses. Very few are based on solid geometric modelers.The present paper emphasizes the need for solid geometric modeling of the casting and rigging system and linkage with a solidification simulator. The nature of some of the technological challenges which have slowed this development are discussed, including accurate description of complex surfaces and their intersections and the bridging of computer encoded information with NC technologies and with FEM-based simulators for stress and thermal analyses. A recently prepared modular-structured FEM simulation code implemented on a micro computer is described.Construction of a solid geometric model of the casting and rigging and validation of the combination for optimum characteristics of soundness, quality and yield by solidification simulation are I inked as key elements in the foundry of the future. Data base support for this CAD/CAM system is rapidly being developed throughout the world.INTRODUCTIONThe simulation of shaped casting solidification using the digital computer, goes back to at least the early nineteen-sixties when Forsund (1) in Denmark applied the technique to the problems of casting surface quality.Prior to that time, the work of Paschkis and co-workers using the analog computer ranges back to the nineteen-forties, when work sponsored by the AFS Heat Transfer Committee at Columbia University revealed many hitherto unknown or only partly anticipated aspects of casting solidification (2).Three reviews of the various historical aspects of simulation should be referenced. Firstly, the AFS monograph by one of the present writers (RDP) and his colleagues - describing background and later work, again sponsored by the AFS Heat Transfer Committee at the University of Michigan (3). Secondly, a review prepared by Durham and Berry (4) which discusses broad aspects of casting solidification simulation. Thirdly, a review by Erickson (5) which contains an excellent bibliography to 1980. In addition to these papers, the publications lists of the CADCAST project* and the proceedings of the two Engineering Foundation Conferences of Casting and Welding Modeling, published by ASME, are also most notable (6) •"

Jan 1, 1986

The earth is a planet limited in size and limited in total resources. For the forseeable future, it is the only available habitat for mankind. Therefore, it follows that the more we know about our planet the better we can utilize its space and its resources for our well-being now and in the future. But, to accomplish this, we need reliable basic information. Geosciences provide such information. Recently, Dr. M. King Hubbert took note of the important effect of the geosciences on society, on how we think, and how we live. In the first century of modern geology, 1780- 1880, the influence of geology was primarily on how we think, i.e. changing our concept of the earth from one with a short catastrophic history to one that developed gradually over enormous spans of time. In the second century, 1880-1980, the emphasis was on how we live, on expanding the knowledge base so that we could more easily find and utilize the earth's resources. Now, in the third century, i.e. from 1980 towards the year 2000 and beyond, we should concentrate on both how we think and how we live; i.e. how we can better estimate potential global' resources and how we can manage these resources for maximum benefit to mankind. Like other sciences, the geosciences build upon what has already been done. Progress is achieved by using the thoughts, measurements, and observations of past workers, adding to these the insights from new experiments and from new concepts. Geology has its own methodology and approaches; but more than most sciences, it calls also upon the tools of physics, chemistry, mathematics, engineering, and biology to help solve its problems. Today's increasing population, increasing industrialization, and increasing complexity of modern society demand more detailed geoscience information so as to better use the land, reduce geological hazards, provide an inventory of resources, facilitate waste disposal, and prepare for long-term effects such as changes in climate and sea level.

Jan 1, 1986

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

In mid-1984, SAIMM reached an agreement with the South African Region of what is now the Institute of Metals to combine the physical-metallurgical activities of the two organizations. This was the outcome of several years of informal collaboration, and followed the recognition in 1982 by the SAIMM Council that applied physical metallurgy had grown in importance to South African industry and should have a place alongside the two areas already well-established for SAIMM commitment and support-mining and extractive metallurgy.

Jan 1, 1986

By W. D. Fogwill, P. J. Clarke

"The Dawn Lake uranium deposits are located 340 km north of La Ronge, Saskatchewan, in the Athabasca Basin between the Midwest Lake and Rabbit Lake deposits. Four zones of uranium mineralization, called the ""11, 14, 11A and 11B Zones,"" lie within the Athabasca Sandstone, at the sub-Athabasca unconformity and in the basement.At Dawn Lake, approximately 100 metres of Helikian Athabasca Group clastic sediments overlie Aphebian Wollaston Group pelitic and calcareous metasediments and pegmatites. Uranium with some nickel, cobalt and copper, occurs near the sheared stratigraphic contact between calc-silicate gneiss and graphitic, pyritic pelite. The mineralization lies in an area of low magnetic susceptibility which is thought to represent a rock sequence lying stratigraphically high within the Wollaston Group. There is no obvious vertical displacement of the unconformity by faulting, despite considerable brecciation, shearing and slickensides seen in the basement rocks. This suggests horizontal displacement on steeply dipping wrench faults as the main tectonic control along the 11, 11A and 11B trend.Below the Athabasca unconformity, the Wollaston Group rocks are altered to fine-grained mixtures of clays, chlorite and silica commonly called regolith. Along the mineralized trend post-Athabasca fracturing and (or) compaction have occurred through this clay-rich alteration zone, causing the steeply-dipping primary foliation to become contorted. This ""crenulated"" horizon can reach depths of 35 metres below the unconformity and is thickest along fault zones in the calc-silicate rocks. The ""crenulite"" is a distinctive unit which at Dawn Lake is commonly found above pods of ore located deep below the unconformity.Much of the mineralization in the 11A and 11B Zones occurs above, beside and below the thickest part of the crenulated zone, although the crenulated rock itself contains negligible amounts of carbonate, pyrite and uranium. Intense vuggy alteration and collapse breccias are found in calc-silicate rocks deeper and to the west of the 11A and 11B mineralization. There are at least two ages of uranium deposition in the basement zones, shown by small bright cubes of ""pitchblende /"" overgrown and replaced by duller botryoidal ""pitchblende II. ""Sooty pitchblende and yellow secondary minerals are the result of still younger reworking.The geological setting of mineralization, along the contact between carbonate-rich calc-silicate rock and pyritic pelite, suggests that the uranium was concentrated at a pH/Eh boundary located between deeply weathered, carbonate-rich and sulphide-rich basement rocks."

Jan 1, 1986