Search Documents

By A. G. Journel

Accurate prediction of recoverable reserves are key to the development and planning of a mining operation. Recovery functions for tonnage, quantity of metal and ore grade are defined and two approaches for their estimation are proposed. The indicator kriging (IK) approach draws on the data rank orders, whereas the multi-gaussian (MG) approach relies on a grade multi-variate distribution hypothesis. Although based on different premises, both approaches yield remarkably similar--and accurate--estimates for recoverable reserves.

Jan 1, 1984

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By Peter J. Szabo

In 1980, a caravan of representatives of Japanese trading companies debarked on the shores of the United States bearing gifts of watches, electronic games, and radios. In early 1983, we find in a parking lot of a major U.S. coal company, a haggard general manager of marketing returning to the Orient with a box under his arm of trinkets of his own; cross pens with company logos, alarm clocks, etc. The tables have turned, but our fellow sitting in a jet plane over the Pacific Ocean had only to heed the warning of the famous 19th Century poet well familiar with the ways of the Far East. Kipling said; "And the End of the Fight is a tombstone white and with the name of the late deceased, And the epitaph drear, a fool lies here who tried to hustle the East."

Jan 1, 1984

By Dr. O’Neil Thomas J., Donald W. Gentry

Pure gold was hidden in the quartz, they said, 'Twas proved by dreams and signs, and rods divining, By chemic tests, and spirits of the dead, In fact by everything-except by mining. " from R.E. White, "The Mining Town," Alta California, August 18,1873 Textbooks in mining engineering have traditionally covered ore reserve estimation and mine valuation in a single volume. Indeed, Examination and Valuation of Mineral Property by R. D. Parks (1957), having been the standard of the profession for over 20 years, is a classic example. However, the state of knowledge in these two fields has grown tremendously. Most mining engineering curricula now cover these topics in separate courses, and in practice, these tasks are usually performed by different individuals. Thus, this trend now suggests the need for separate, specialized publications rather than a single volume for both topics. Because of the separate development of the science of ore reserve estimation, it is important to state at the beginning what this chapter does not cover. It does not address in detail the design of sampling programs, sampling methods, or the processing of samples or sample data compilation. There are a number of suitable references available on these topics, including Peters (1978), Gy (1979), as well as the previously cited book by Parks. Furthermore, this chapter does not cover in any substantial detail either the traditional methods for using sample data to calculate ore reserves or the more recently developed geostatistical methods. The traditional methods are thoroughly covered by Popoff (1966) and more concisely by Barnes (1980). Among the more useful references for statistical applications in ore reserve estimation are Barnes (1980), David (1977), and Clark (1979). A thoughtful review of the entire science and art of ore reserve estimation is provided by King, McMahon, and Bujtor (1982). In spite of the fact that expansion of knowledge now calls for separate books on ore reserve estimation and financial evaluation, neither publication can ignore the important interrelationships between the two fields. In regard to this text, the unique and crucial role of ore reserves can not be omitted entirely; however, the field is now simply too extensive to treat here in any comprehensive manner.

Jan 1, 1984

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick 's 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province' s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province' s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province's plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec's progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By S. R. Knowles, R. J. McDonough

"The purpose of this paper is to introduce to the minerals processing marketplace a viable alternative to conventional mechanical agitation and pachuca airlift agitation. What follows is a brief introduction to the Atara Corporation and the fundamentals of how an Atara ""cannon"" mixer operates. The main body of the paper is concerned with the results of a study to evaluate the cannon mixer for a gold cvanide leach application. A brief summary of research and testing for other metallurgical applications is also presented.1. 1 THE COMPANYThe Atara Corporation is a privately owned Canadian company, headquarted in Dorval, Quebec. Its subsidiary, Atara Incorporated, located in Paramus, New Jersey services the municipal wastewater treatment market in the United States. Dorval focuses on industrial mixing applications in Canada and the US. The Atara Corporation provides design, engineering and specifications of agitators for mineral land other) processing applications. Fabrication of mixers is pursued in either Canada or the US, depending on the ultimate destination.Although Atara and its unique static in-tank mixer are relative newcomers to the mining industry, the cannon mixer has demonstrated its value over the past 20 years in municipal wastewater treatment services. In the past four years the Atara unit has been developed for industrial applications; the bulk of the development work has been for metallurgical applications. To-date the cannon mixer has been evaluated for mixing slurries in the following applications: nickel-copper concentrate storage, copper concentrate storage, coal slurry storage, gold cyanide leaching, uranium acid leaching, silver leaching and zinc acid leaching. Atara mixers have been installed with successful performance in full scale tanks containing nickel-copper concentrate slurry (Falconbridge) and gold cyanide leach pulp (Dome"

Jan 1, 1984

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

In the flotation of fine particles, problems arise which do not occur with coarse-ground pulps. For example, the presence of colloidal or near-colloid- al gangue particles gives rise to ex- cessive entrainment in the froth, with reduced grade as a consequence. If the values themselves are finely dissemi- nated, the recovery usually decreases as the particles diminish in size, so a low recovery is combined with poor grade. Sutherland and Wark (1955) referred to the complications arising from the presence of fines, indicating (p.382) that fine grinding "introduces diffi- culties that have not yet been satis- factorily overcome". At the time of writing, very little work has been done on fines flotation specifically, yet the groundwork has been well laid. The availability of better scientific instruments, together with the general advance of understanding in a wide variety of relevant research fields, has taken us a long way toward finding the reasons behind the problems as- sociated with fines, and also toward finding practical solutions. It would be useful to define what is meant by "fine" particles before going further. To some extent, the definition is somewhat elastic as far as flotation is concerned, because the density of the particles has a bearing on whether or not they act as fines. But in general we are dealing with particles less than about 20 pm in Diameter.

Jan 1, 1984

By James F. Lemons

The potential production of cobalt from nickel sulfide deposits in Canada, from nickel laterite deposits in the Pacific Islands, and from the copper deposits of Zaire and Zambia will be a function of the cost of recovery of the primary nickel and copper products. This cost of production varies significantly for these deposits and is related to the differences in the cost of labor, energy, and supplies, to production technology, and to the grade and recovery of nickel, copper, and cobalt. This Bureau of Mines paper investigates these cost and technology differences as they relate to the cost competitiveness of the deposits in Canada, Zambia, Zaire, and the Pacific Islands.

Jan 1, 1984

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By C. M. Brinckerhoff

Much has been written in the mining technical magazines about the caving system. Many of these articles were published in the Transactions of the American Institute of Mining Engineers prior to World War II. In recent years little has been written on mining methods or on the detailed planning always required. Block caving had primarily been used to mine deep copper ores in Africa, the United States and in Chile, although other ores had been mined by this same system. Asbestos ore had been caved in Canada, tin ore in Bolivia, molybdenum ore in Colorado, iron ore in Wyoming and Sweden, and limestone in California.

Jan 1, 1984

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 RC was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique and weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure errosion it was found that there was a synergistic effect between corrosion and erosive wear. Erosive wear rates are given as a function of pH and mineral type.

Jan 1, 1984

By E. K. Albert

Computer oriented simulation techniques can be effective in the design and analysis of complex mining systems. In fact, a number of computer software products are available for mine systems simulation. While providing a useful tool for the investigation of mine planning problems, the availability of graphic output was limited or non-existent. Computer graphics is a natural extension of mine simulation methods and provides a more dramatic level of understanding and interface with an engineer. With today's high cost of venture development, the need for an easy to use but complete systems model which includes the major elements of mine planning with an interactive graphics interface has never been more apparent. In this paper, the underlying philosophy of design of an interactive interface to a complete surface mining simulation model is described. The basic structures of the surface mining system and the simulation model are discussed. The methods and algorithms used to implement the various subsystems are presented. Practical considerations of the design of displays and user interaction are illustrated, especially as they apply to the application of the package by a mining engineer. A simple example is provided to demonstrate the concepts embodied in the model and to show how a simulation is built from mine data.

Jan 1, 1984

By Howard L. Hartman

The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry is not unaffected by the drought: not only is research lagging, but hard- pressed universities are going to the private sector for funding. This paper's thesis is not that mining companies should shower universities with philanthropy, but that a quid pro quo ought to be exacted: a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that may lend itself to adoption by our industry.

Jan 1, 1984

The theme of my address to your Institute, indeed its name, is "The Mineral Industry - What Next?" Knowing that I was required to make four appearances, and not wanting to be too repetitious, I wrote a rather long speech of which I will deliver various sections at different places, with a common introduction. Specific areas I have addressed are "Exploration", "New sources of minerals and energy", and "Mining and metallurgy of the future".

Jan 1, 1984

By Martin Hertzberg

In this Bureau of Mines study, an equation is derived for the limit burning velocity for divergent, spherical propagation from an ignition kernel of radius, r: (Su)e = ( ) . For flame propagation into a preexisting, stretching velocity gradient of magnitude dv/dx, the limit velocity is (Su)e = (a dv/dx)1/2. These formulations are shown to be equivalent to the fluid dynamic concepts of Damkoh1er, Kar10-vitz, and Markstein. Existing data for the b10woff limits of flames are shown to give excellent agreement with those concepts provided that proper account is taken of two dilution effects: composition dilution caused by entrainment and velocity gradient dilution caused by flow expansion. Approximate flow-field solutions are also derived for the unburned gas motion above an upward propagating, spherical flame kernel in buoyancy-induced flows. It is shown that;, the upward hemisphere propagates toward a stagnation plane in a counterflow configuration involving the balance between the combustion force, which accelerates the cold gas upward, and the buoyancy force that accelerates the cold gas downward. The position of the stagnation plane above the upward propagating hemisphere is related to the ratio of the buoyant velocity, vb, to the burning velocity, Suo Extinction of the upward propagating wave occurs by flame stretch in that counterflow configuration when n = Vb/Su begins to exceed the expansion ratio, Pu/Pb' and the wave is blown off by its own buoyancy-induced flow field.

Jan 1, 1984