Search Documents

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By A. M. Laird

Endako Mines' molybdenum operation is located near the geographic center of the province of British Columbia, Canada. The property is six miles south of the Northern Transprovincial Highway and the northern main line of the Canadian National Railway. The area is broken by high hills covered with dense stands of spruce and pine with vast areas of the valley floors covered with aspen and poplar. The climate is moderate with precipitation averaging 22 inches per year. Approximately four feet of snow accumulates in the winter, and temperatures range from 900 F. in summer to -40° F. in winter. The orebody, a lowgrade porphyry type deposit, occurs in a widespread granitic intrusive which has been locally weakened at the intersection of two regional faults. In this vicinity the quartz monzonite has been further shattered to permit the entry of mineralizing solutions and local dykes. Two types of mineralization occur within the orebody. The most prom¬inent is the six inch to four foot wide continuous quartz veins with characteristic ribbons of molybdenite and frequently finely-divided grains of molybdenite within the quartz. The second type occurs as fine fractures filled with quartz molybdenite in the form of a stockwork halo radiating out from 20 to 200 feet from the quartz veins. Minor hematite, magnetite and chalcopyrite are also present. Mineralization is roughly proportional to the extent of kaolinization in the quartz monzonite, kaolinization being one of three distinct forms of hydrothermal alteration. Pyrite is commonly associated with molybdenum mineralization within the orebody and a pyrite halo is recognized on the south side of the orebody.

Jan 1, 1968

By C. O. Brawner

Approximately 7 billion tons of soil, rock and ore are currently being excavated in open pit mines and quarries on the North American continent at the present time. As the depth of excavation increases and the grade of ore being mined reduces, the safety and economy of the stability of the pit slopes becomes increasingly important. The magnitude of the potential influence on economics can be appreciated from the results of recent full scale field studies by Kennecott Copper Corporation at the Kimbley pit near Ely Nevada (Merrill, 1968). This pit was originally excavated with an average wall slope of 45°. Based on detailed studies it appeared that a slope of 610 would be stable. Subsequent excavation to this slope proved the original pit could have been steepened by 16° during production.

Jan 1, 1968

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By W. A. Gow

"In January of 1964, a group known as the Canadian Gold Metallurgists was formed with the backing of the managers of most Canadian gold mining operations. This organization is composed of about thirty mill superintendents of Canadian gold milling operations where the cyanidation process is in use, and one member from the staff of the Mines Branch, Department of Energy, Mines and Re-sources, Ottawa. The aim of this group is to bring together gold mill operators, and research and development people from both industry and government for the purpose of discus-sing common metallurgical problems, and deciding on what operational R and D efforts can be made to help solve these problems. Since the conception of this organization, this approach taken by the gold industry to the study of metallurgical problems has resulted in benefits to all operators, both by assisting them with problems peculiar to their own individual operations and by providing developments of general interest to the industry.This paper describes events leading up to the formation of the Canadian Gold Metallurgists, and how the group has operated since its formation. Examples of progress made toward the group's objectives are given, and possible future programs are discussed."

Jan 1, 1968

By E. C. Wilson

The knowledge concerning the lubrication of open gearing for mining machinery has contained many unknowns and at its best has relied to a great degree on a "Rule of Thumb" procedure. It will be within the scope of this paper to explain what we have learned to date and what must be learned in the future. The results in the lubrication of open gearing have spanned the spectrum of unsatisfactory to satisfactory. With the advent of larger mining machinery, we are faced with the necessity of a more thorough knowledge of open gear lubrication. We have avail- able, better steels for the gearing, advanced technology and machinery for cutting proper tooth profiles, and better means of aligning the teeth in the gear train. This has made it possible to transmit more horsepower through the same size gear set than ever before, if we have the proper lubrication to complement the factors previously mentioned. We have set up computer programs which can calculate the data fox the tooth forms, the correct operating center distances, the contact stresses, the bending stresses, and the PVT factor of the gear teeth. This program does not, at the present, have sufficient data available to calculate the type of lubricant which should be used.

Jan 1, 1968

By Warren E. Morrison

A simplified energy model for the United States is quantified for a recent historical period. The basic model and calculated quantified structures are used for a number of analytical case studies that estimate midterm and long-range shifts in patterns of energy resources demand and required supply. Historical data series are presented for the years 1947 to 1965 in the form of integrated energy balances by source, form, and consuming sector. In case studies I to XII, conditional projections of historical trends of energy demand and required supply are made for the midterm period 1966 to 1980. The projections are carried out by correlation of major energy components with relevant independent variables such as major economic indicators. Simulations of the medium-range projections to 1980 are carried out by varying the assumptions for the determining variables to produce high-and low-range projections for the midterm period. Case studies XIII to XXII are long term contingency or technological forecasts to the year 2000. These cases assume technological changes or innovations that produce major shifts in the long term pattern of energy consumption and the mix of required resources. The domestic resource base is assessed in its ability to meet projected or forecast demand for energy resources under the midterm and longrun assumptions made in the various case studies. Various energy issues or problems identified from the analyses of the case studies are discussed, and possible alternative approaches to solutions to these issues or problems are suggested.

Jan 1, 1968

By Sidney Katell

This report, covering the period January 1967 through December 1967, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the ninth in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week.

Jan 1, 1968

By William R. Barton

Dimension stones, with their almost infinite variety, have a broad range of properties and uses. Natural stone was beyond doubt the first mineral commodity used by man. Today dimension stone has widened to encompass building exteriors and interiors, decorative and ornamental modes, statuary, monuments, paving, curbing, flagging, roofing, and miscellaneous categories such as blackboards, surface plates, and honestones. For many purposes, it competes with greater or less success with alternate materials such as concrete, metal, brick, plastic, or glass. The almost ubiquitous geographic distribution of stone resources is the basis for a dimension stone producer industry in almost every State and in almost every land. In the United States, alone, dimension stone sold or used by quarries is valued at 2 million to 3 million dollars annually. Mining, finishing, transportation, and use technology have been modernized, resulting in a broader spectrum of stone products and new adaptions in use. Increased efficiencies also have been reflected in costs and prices and, coupled with gains that should be realized from current research, auger well for continued vitality of the ancient and honorable dimension stone craft.

Jan 1, 1968

By Harold M. Smith

This publication summarizes the literature on the composition of petroleum, with special emphasis on naphtha and gas oil, and provides a source book for the known qualitative and quantitative facts on crude oil composition. The discussion points out the known facts from supposition, and suggests new researches needed in various areas.

Jan 1, 1968

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By George L. Wilhelm

Many factors, some of which are not easily defined or described, must be considered in the design of a hydraulic backfill system. After participating in the design of several plants, I have a conviction that future refinements in sandfill systems must come in large part, from the merging of good design ideas and information from existing operating plants. It is important then, that we document and publish information on existing plant designs and their operating characteristics. This information will then be available for use by our successors and later innovators in hydraulic fill placement. The Mayflower hydraulic sandfill system is similar to other plants. The intent of this paper is to describe only this system's unique design and operating characteristics. I will not describe in any detail, the familiar elements of the system. I will document some of the observed hydraulic characteristics of the system, elaborate on some of the design situations that had to be solved, and will discuss operating factors that are not generally described in our technical literature.

Jan 1, 1968

By E. F. Young

An integrated steel company is an industrial complex ranging from raw materials mining, through pyrometallurgical smelting and refining, and hot shaping, to product finishing and coating. Within this complex is a great variety of operations which use vast quantities of water, and a variety of water uses which can result in pollution of many different types. The industry has recognized most of its problems for some time, and has spent a great deal of money and effort in reducing and eliminating pollution. A recent survey by AISI showed that the industry has spent, within the last 15 years, two hundred forty millions of dollars on water pollution control, and has authorized spending eighty-seven millions more on this type of non¬productive facilities. While much still remains to be done, I think the record to date is one we can be proud of. In this presentation, we will attempt to outline a number of the water pollution problems encountered in an integrated steel company and to show what types of corrective action have been and are being taken, using Jones & Laughlin Steel Corporation as an example.

Jan 1, 1968

By George Markon

The importance of United States coal exports as a component of the national economy, the potential for growth of these exports, and the inter-national character of this sector of the coal industry are described in this report. The report summarizes some of the many background elements in the rise of United States coals to preeminence in highly competitive world markets. It presents some insight into this important sector of United States industry and the positive contribution of this sector to the Nation's balance of payments. It contains pertinent basic statistics on production, trade, and consumption of coal in most major markets for 1960-66. The report examines the movement of United States coals from mines to export markets, tracing and describing origins, exit ports, prices, and trends as well as inland and ocean freight rates and other data vital to an under-standing of some of the practices and complexities of the United States coal markets abroad. A brief sketch of coal production and consumption in principal importing countries is also presented with a short review of some of the more current practices and problems of these countries. Coal produced in inland areas of the. United States can be moved to and distributed economically within coal-producing countries overseas and in Canada. Quality coals from the United States can successfully compete with foreign coals in nearly any area of the world on a truly economic basis because of their high grade and their low cost which derives from the high productivity of the miner and from reasonable ocean freight rates. Because of tariffs, trade embargoes, quotas, and other restrictions, how-I ever, foreign coal markets are relatively limited. Further limitations are imposed in some countries by economic conditions which restrict all imports as a matter of financial and economic necessity. Despite these obstacles, United States coals have brought lower cost quality coals to a large segment of the foreign energy market.

Jan 1, 1968

By Eldon C. Pattee

Reconnaisance samples of reported beryllium occurrences in Idaho, Washington, Montana, and Oregon were chemically and spectroscopically tested in a mobile laboratory. The two predominant types of occurrences were green beryl associated with Cretaceous intrusions and disseminated aquamarine associated with Tertiary intrusions. Although the beryllium content of known deposits in the Northwest is too low for economic development at present, total submarginal-grade beryllium resources in pegmatites are estimated to be 570,000 to 1,870,000 tons containing 0.024 to 0.167 BeO. A potential source of 500,000 to 700,000 tons of beryllium-bearing tactite in Idaho and Montana averages 0.033 to 0.080 percent BeO.

Jan 1, 1968

By Charles B. Manula

Judging from the rapid pace of increased demands for mineral products, technological forecasting will become an increasingly necessary tool in mining. Even though the mining industry in 1966 produced more are than ever before, current extraction rates are only a fraction of what is expected in the later years of the twentieth century. If metal and mineral commodities continue to hold their respective and present share of markets, the prospect of coping with demands from a population that will double in the next thirty years can become an impossible task when viewed outside the limits of technological advance and change. Those mining companies that are doing little to develop new and expanding horizons for their operations cannot expect to survive. Nearly 90% of all metals and mineral products consumed last year was recovered by open-pit mining. This has placed great pressure on this segment of the industry which, consequently, has resulted in some spectacular developments. Already production rates at many places are dwarfing those of the Panama Canal and other well-known earth moving projects which are frequently identified as massive undertakings. With projects of this scale, the need for increased sophistication of engineering, planning, management and administration of modern mining installations has never become more apparent. The design of complete systems for the mine and plant that fit the mould of today's business and social environments is undergoing an evolutionary process.

Jan 1, 1968

By W. R. K. Wu

This bulletin traces the development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of the pertinent literature. The bulletin was written as a part of the Bureau of Mines research program on synthetic liquid fuels. It covers the history and economics of the process; the chemical aspect of hydrogenation of coal, tar, and middle oil; the engineering aspect of converting coal and tar to liquid fuels, principally gasoline; and the equipment for the process. The literature covered includes documents of the United States and British Governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.

Jan 1, 1968

The 1967 Lignite Symposium was held at Grand Forks, N. Dak., on April 27-28, 1967. This was the fifth of these technical meetings and the fourth which was cosponsored by the University of North Dakota and the Bureau of Mines. These symposia have provided a meeting place where current developments concerning technology and utilization of solid fuels (lignite) are presented. There was a registration of 255 persons from 24 States, the District of Columbia, six Canadian Provinces, Germany, and India. Many segments of coal or energy oriented organizations at many levels were represented. During the meeting, 18 presentations were made covering developments in electrical power generation, mining, estimation of reserves, combustion, gasification, and chemical and speciality uses of low-rank coals; these are com-piled in this Information Circular to provide a record of the symposium and to permit wider dissemination of the information. Proceedings of the other meetings have also been published.3

Jan 1, 1968

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968