Search Documents

By Adrian J. Mathias

For many years excavations were made in rock exclusively by conventional blasting methods, and without concern for damage to the rock surfaces which remained after the excavation was completed. Recently, however, there is an increasing awareness for the importance of making rock excavations with as little damage as possible to the remaining rock surfaces; consequently, several revolutionary new precision blasting techniques have been developed during the past few years. These techniques, variously known as cushion, smooth- wall, perimeter, pre-shear, and pre-split blasting, basically involve the creation of a fracture plane in the rock between a series of blasted holes. The variations in each of these techniques are largely due to the differences in hole diameters, hole spacings, methods of charging, and sequence of blasting used to achieve certain specific results. The development of these precision blasting techniques was initiated by Canadian Industries Limited in 1953 at the time the Sir Adam Beck No. 2 Hydro-electric Project was under construction by the Hydro-Electric Power Commission of Ontario. Since then, these techniques have been somewhat advanced, and they have been applied with varying degrees of success to a number of projects. These projects include railroad and high- way cuts, dam spillway channel excavations, canal excavations, tunnel driving, shaft sinking, and other underground applications.

Jan 1, 1965

By Nicholas J. Grant

It is the purpose of this paper to examine a number of the recent developments in powder metallurgy, being most concerned with those which are yet to prove themselves rather than those which have achieved commercial maturity. Such developments include the production of very much coarser and very much finer powders, down to the near-micron size range. Also considered are activated sintering, direct powder rolling and extrusion (both hot and cold), brazing and welding, hydrides of reactive metals, oxide dispersion strengthened alloys and theoretical evaluations. Introduction T HERE surely can't be very much argument with the fact that powder metallurgy has made large advances on many fronts during the past ten or more years (1). These advances have taken place in raw materials, in processing, in product development and in a better understanding of many of the phenomena which occur in the various steps involved in powder metallurgy. It should be clear, in view of such growth, that it will not be possible to highlight all of the new developments in the present paper. Many of these developments,

Jan 1, 1965

By Robin O. Williams

Robin 0. Williams (Oak Ridge National Laboratory)— The authors have questioned the degree to which the coherency strains between the iron-rich and chromium-rich phases are isotropic as proposed in Ref. 5 on the basis of the difference between the elastic properties of the two phases. The relative magnitude of the stresses is determined by the moduli as shown by Eqs. [2], [3], and [4] of Ref. 34. However, the moduli of the two phases have no direct bearing on the uniformity of either the stress or strain within either phase. The idea that the strains are isotropic within each phase (but normally of different magnitude and always of different sign) is based entirely upon the experimental observation that X-ray line broadening has not been detected even when the particles become rather large. It has not proven possible to grow the particles sufficiently large that they lose coherency. Based upon this lack of line broadening one can estimate an upper limit for the nonuniformity of the strains within each phase as follows. It is considered possible to detect line broadening if it is as great as 10 pct of the separation of the K, doublet for the (211) line using chromium radiation. The doublet separation would correspond to a total strain of 0.0017 such that the total variation of lattice parameter relative to the average lattice is now k0.05x0.0017 or something less than ± * For the present case the strain in each phase is roughly 0.002 such that the variation of strain within a phase will not exceed 5 pct. It is stated that the expression derived for strengthening for the hydrostatic straining as observed in this system would substantially overestimate the magnitude due to dislocation flexure. This is contrary to the conclusion reached in the original paper34 for the present range of particle sizes. What is the lowest temperature at which a has been observed to form in this alloy? M. J. Marcinkowski, R. M. Fisher, and A. Szirmae (nutlzors' reply)— -Williams' arguments based on X-ray findings for a chromium-rich precipitate and an iron-rich matrix strained to a common lattice parameter are certainly convincing. This being the case, there are no shear components of strain associated with the precipitate-matrix aggregate to interact with the shear components of the dislocation stress fields, contrary to the opinion expressed by the present authors. On the other hand, the present authors, in spite of this error, did not expect the shear interactions to be significant. The chief objection to Williams' model in the present case is that the various segments of the dislocation line are assumed to pass from one potential valley to the next independently of neighboring segments. This is only true for a highly flexible dislocation line, i.e., one whose radius of curvature is something less than the center to center distance between precipitate particles which amounts to about 90A in the present alloy. In order to maintain this curvature, an externally applied shear stress of at least 230,000 lb per sq in. would be required or about four times the observed stress. It is therefore concluded that the dislocation lines move rather rigidly through the lattice. This being the case, the forces on the dislocation resulting from the hydrostatic interaction between the stress fields of the edge-dislocation components and the precipitate particles should average out to zero; that is particles above the below the slip plane produce forces on the dislocation of opposite sign and therefore will cancel when averaged over the entire length of the dislocation. On the other hand, since the dislocation is not perfectly rigid, Williams' model may lead to some strengthening, but far less than that predicted. A second and equally serious objective to using Williams' strengthening model for the present alloys is that profuse wavy slip due to the motion of screw dislocations played a predominant role not only in the unaged alloys but in the fully aged ones as well. Since the screw dislocation has associated with it only shear components of stress the hydrostatic strengthening model no longer applies. In view of these arguments the present authors must reject Williams' model of strengthening as being pertinent to the present alloy system. The present authors have made no detailed study of the lowest temperature at which a forms in the quenched ferritic alloys. None was ever observed n the alloys aged at 500°C so that forma-tion must occur at temperatures higher than this and was therefore not a factor in the present study.

Jan 1, 1965

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By Thomas P. Meloy

There is much interest in the automation of entire comminution circuits, At the present technological level it is possible to automate a circuit but to date it has not been done, To successfully automate a circuit, a number of problems must be solved. Not all of them are engineering problems. The purpose of this paper is to discuss some of these problems, as certain the implications of these problems and indicate solutions to them. In this paper the term "automation" is used loosely but in the popular sense. Namely, that a plant is automated if a computer is used to control the basic flow of the materials as well as setting the critical parameters in the process. Specifically, the discussion will concern itself with the control of comminution circuits from the dumping of the ore into the primary crusher until the final interface between the comminution circuit and say, the flotation mill in the case of a sulfide ore.

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By F. X. Ferney

The centrifuge which will be reviewed in this dis¬cussion is the continuous solid bowl typo. As there are presently approximately 2000 of these units operating in our country, and about 200 of these in use in the coal industry, I expect that most of you are acquainted with its operating principle. How¬ever, for those who are not familiar with the machine a brief introduction is in order. The continuous solid bowl centrifuge was first successfully marketed, worldwide by the Bird machine Company in 1934. The successful development of this unit was based primarily on the invention of a drive mechanism to properly control the differential speed between the two rotating elements. This centrifuge was introduced into the coal industry immediately following the second World War. Today there are five or six additional firms' selling this machine in our country, and approximately twenty others in Europe, England and Japan.

Jan 1, 1965

By G. T. Swanby

Members of AIME, I read to you now a portion of a very fine business letter which we received several years ago. This letter originated in Rangoon, Burma, and reads in part: "Rest assured, if your goodselves see with us eye to eye, sure as certain we should get the business". I don't plan to give anybody "the business" today, but you can rest assured that if some of "you goodselves see with me eye to eye" on what I am about to discuss, I would be most pleased. My talk with you today will discuss the Federal Corporate income tax and its effect on our lives as engineers. In the-engineering-construction business we are faced with all the usual form of taxation which includes such items as sales tax, use tax, school tax, contractor; gross receipt tax, import duties and excise taxes, severance taxes, etc, adinfinutum.

Jan 1, 1965

By Laurence B. James

The California Department of Water Resources is concerned with the development, distribution, and protection of the State's water resources. Geologic activities of the Department relate to planning, construction, and operation of water projects, supervision of the safety of over 900 dams under state jurisdiction, and investigation and control of ground water supply. The Department is engineering oriented, and the role of the geologist is to assist with the solution of engineering problems. Some of these problems require the integration of many talents, including not only those of geologists and engineers, but also those of economists, lawyers, seismologists, chemists, geophysicists, and hydrologists, Frequently, a task force of several disciplines will attack a problem as a team.

Jan 1, 1965

By R P. Douglas

During 1955, Cominco commenced an exploration pro-gram in northern New Brunswick; in the following year, what is now the Wedge mine was discovered. The mineralization is mainly pyrite, with associated chalcopyrite and minor amounts of sphalerite and galena. The property was brought into production at 750 tons per day in early 1962. The ore is trucked 10 miles to the Heath Steele concentrator, where a copper concentrate grading about 19.5 per cent is produced and shipped to the Japanese markets through the port of Dalhousie, New Brunswick. Introduction THE Wedge mine, owned by The Consolidated Mining and Smelting Company of Canada Limited (Cominco), is located in the Newcastle-Bathurst area of New Brunswick. It is 42 miles by road northwest of Newcastle and 37 miles southwest of Bathurst (Figure 1). The mine is located on the north side of the Nipisiquit river in one of the more mountainous areas of the Province, the local relief rising to 1,500 feet above sea level. There is an almost complete forest cover of mixed hardwoods and conifers -the val-leys and hillsides being covered by balsam, spruce and pine, the swamps by cedars and black spruce and the highlands by mixed hardwoods.

Jan 1, 1965

By Delbert L. Keenon

The principal concepts of computer control and automation have been successfully applied in industries world-wide, The enthusiasm generated by the proponents of computer control, and the apparent mystery enveloping the techniques of computer control, have caused attention to be focused on this infant industry from all quarters. Consequently, the motivation to "computerize" may be the hope that computers will solve all economic problems. The truth remains that not only have there been monumental successes, but there have been some colossal failures. This paper will attempt to outline a generalized guide to computer control and present methods for avoiding some of the major pitfalls. Since the investment required for computer control systems has been drastically reduced in the past year, small operations will likely find that computerized process control is attractive in areas where it has never been considered before, The discussion presented here is intentionally non-technical and directed towards those who may soon find they have a possible application for a control computer. The primary purpose of computer control is to reduce expenditure and increase profits by improving the quality of product, increasing the efficiency of operation, reducing the materials and man hours required or a combination of these. Success or failure to reach the desired goal depends, to a large degree, on a well-planned approach. This includes recognizing a possible computer application, properly defining the job which is to be accomplished, evaluating computer systems, selecting a capable manufacturer, and following through with sound systems engineering and programming.

Jan 1, 1965

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

By R. Littlewood

The concepts of "redox potential" and "oxide-ion activity" are suggested as measures of the fundamental slag properties of interest to the extraction metallurgist. Thermodynamic data for single oxides are presented graphically in these terms and a method of expressing desulfurization of steel in electrochemical terms is indicated. The application of the theovy to mixtures of oxides (slags) is discussed and the redox potential is shown to provide a link between all the redox equilibria in a slag-metal system. In particular, the redox potential of the slag, its basicity, and the oxygen partial It is now generally recognized that slags are mixtures of polymeric anions of silicates, aluminates, phosphates, and so forth, neutralized by cations. However, conventional thermodynamic treatments of slags have almost always been in terms of activities of the pure component oxides (e.g., SiO,, CaO, A1203, and so forth), which are known not to exist as such in slags. While this type of empirical treatment is perfectly acceptable and provides a rigorous and self-consistent way of considering thermodynamic properties, it can give little guide to the structure of slags, since its very nature ig- pressure are closely connected. Direct deternzination of these by electrode-potential measurements is possible. Literature calculations of ion activities in the system Ca0 -Fe0-SiO,/molten iron are used to evaluate redox potentials, which are shown to correlate with data on sulfur partition in the system. In addition to its application to equilibrium conditions, an electrochenzical approach to slag-metal reactions might provide a basis for new methods of studying the kinetics of these reactions and for plant-control instruments in the pyrometallurgical industries. nores such complications. Recently, the thermodynamic properties of some slags have been successfully interpreted in terms of activities of anions of varying degrees of complexity. (While these have been successful curve-fitting exercises, there is no direct implication that the anions used in the models are necessarily the ones which actually exist in slags.) The success of these ionic thermodynamic treatments is encouraging but a complete picture of slag structure is still a long way off. What is needed is a complete knowledge of the values of stability constants for all reactions in slags of the type:

Jan 1, 1965

By G. R. Kotler, W. A. Tiller, H. V. Ashcom, S. O&apos, Hara, W. C. Johnston

The grain-refinement effect of electromagnetic stirring of Sn-Pb alloys during solidification is investigated at higher field strength and in larger-sized samples. It is found that the grain-refining effect is due to a crystal multiplication phenomenon rather than a nucleation phenomenon. The effect increases with sample size for a fixed field strength and a fixed supercooling bath temperatures. The effect in other alloys was investigated. IN a recent publication1 it was reported that significant grain refinement could be produced during the solidification of a supercooled melt of Sn-Pb alloy when a critical degree of electromagnetic stirring was present in the melt. Thus, for a particular supercooling, AT, a critical magnetic field, Hc, existed at which the number of grains per unit volume, n, increased rather abruptly by a factor of 103 to 104 as the field, H, was increased by a small amount. It was further found that the undercooling at which the melt spontaneously nucleated, ?Tn, was independent of the magnetic field. These authors matched their experimental results against the qualitative expectations of existing theories and found each theory somewhat unsatisfactory. One important question that was not answered in this previous work was "should the effect be classed as a nucleation phenomenon or as a crystal-multiplication phenomenon?" Other valid questions that need answering are: i) do higher magnetic field strengths alter the nature of the results?; ii) what is the effect of higher lead content in the alloy?; iii) what changes occur when one extends the experiments to larger-diameter samples?; and iv) is this a universal effect applicable to the grain refinement of all materials? The present work directs its attention to answering these five questions. The

Jan 1, 1965

By C S. Walker

This paper analyzes the physical, operational and economic site conditions which were conducive to the design of a diesel-electric power plant wherein the over-all use of the thermal energy of the fuel exceeds 80 per cent. The heat energy supplied to the diesel engines is recovered in power generation, vapour phase cooling, waste heat boilers, air to exhaust gas heat exchangers and lubricating oil coolers. Electric boilers are also integrated into the plant design to enable the ratio of electric power output to heat recovery to be varied to suit the seasonal and daily variations. The criteria relative to thermal and electric power design requirements are discussed, and the design details of some parts of the plant which conform to these criteria are illustrated. Some data in regard to the actual operation of the plant over a short period are also included. Introduction THE Cantung mine (Canada Tungsten Mining Corporation) is located some 180 miles north-east of Watson Lake, Yukon Territory. It is situated on the upper reaches of the Flat river at an elevation of about 3,700 feet.

Jan 1, 1965

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965