Search Documents

By P. L. Woolf, N. Bernstein, M. M. Fine

Continuous experimentation utilizing a 3- by 36 - foot rotary kiln was conducted to demonstrate the feasibility of simultaneous induration and reduction of magnetic taconite concentrate . Lignite , or lignite - anthracite mixtures , and green magnetite pellets (64.2 percent Fe , dry basis ) were heated in a rotary kiln to about 2,100 ° F. After separation from excess reductant , the product pellets were found to be highly reduced and acceptably hard . A total of 140 tons of prereduced pellets with an average Fe content of 79.0 percent was produced at Minneapolis and smelted in the Bureau's experimental blast furnace at Bruceton , Pa . Two additional supplies of prereduced pellets were obtained from The Steel Company of Canada , Ltd. , Hamilton , Ontario , which contained 83.8 and 91.3 percent Fe , respectively . Smelting of prereduced pellets was compared with that of unreduced pellets obtained from The Hilton Mines , Shawville , Quebec , and from the Erie Mining Co. , Hoyt Lakes , Minn . Blast furnace tests established that a substantial decrease in coke rates and higher production result from the use of prereduced pellets .

Jan 1, 1964

By H. R. Shell, Robert C. Johnson, Wilbur H. Warwick

Alpha silicon nitride fibers , Si3N4 , were successfully grown in graphite crucibles by a new method utilizing silicates and silicon ( S in equations below) as sources of silicon and using carbon , aluminum , and silicon as reducing agents (R in equations below ) . The basic reaction mechanism is believed to be generally as follows : 1,300 - 1,500 ° C S + R + N₂ SiO + RO + N₂ › 3Si0 + R + 2N₂ _1,300 - 1,500° C 3RO + Si¸N • ( 1 ) ( 2 ) A build - up of coatings on the solid raw- material particles hindered the evolution of silicon or silicon monoxide vapor and thereby slowed down further formation of silicon nitride fibers . Free oxygen in the crucible caused the formation of amorphous silicon dioxide ( SiO2 ) fibers . This problem was solved by passing , entering , and exiting gases through layers of lump graphite inside the reaction vessel . The silicon nitride fibers grew best around 1,400 ° C. Nitrogen flow rates from 4 to 6 liters per minute were adequate . The fiber widths were generally only a few microns whereas their lengths sometimes reached one - quarter inch or more . Chemical and X- ray analyses indicated that bulk fiber samples were usually 80 to 90 percent Si3N4 . The fibers had good oxidation resistance to about 1,260 ° C. Thermal shock resistance was excellent . Electrical resistance was determined .

Jan 1, 1964

By Theodore L. Turner, Joseph H. Swift

A study on a small laboratory scale was made of the use of ammoniacalammonium carbonate for batch leaching Mn from low- grade manganiferous materials ( 6 to 16 pct Mn) obtained from deposits in the southern district of Aroostook County , Maine . These materials were partially reduced at 500 ° to 700 ° C with H₂ or CO and then leached with solutions of NH and CO₂ dissolved in water . Extraction of 80 to 90 pct of the Mn was obtained from some sample materials , but 10 to 34 pct of the iron was also extracted . Material from the Littleton Ridge deposit contained manganese intimately associated with Fe , a condition which contributed to difficulties in obtaining a commercially acceptable product . Extensive investigations of the leach and reduction processes with various mixtures of H₂ and water vapor , and CO and CO₂ , failed to disclose a set of conditions for selectively leaching the manganese . Finely divided metallic Fe was probably produced during the reduction steps so that Fe was leached with the Mn in the subsequent extractions .

Jan 1, 1964

By R. W. Hiteshue, R. W. Fridy, W. Kawa

A study of the production of coronene , a high - melting ( 440 ° C ) , highboiling ( 525 ° C) , polynuclear hydrocarbon , was made by the Bureau of Mines to determine the maximum yield obtainable by the hydrogenation of coal and coalderived materials . Experiments were made with anthracite and bituminous coals and with asphaltenes and centrifuged residue obtained from heavy oil produced in a pilot plant by the hydrogenation of a bituminous coal at 2,000 psi and 480 ° C. With anthracite , yields of coronene of 0.5 to 0.7 wt pct of moistureand ash - free coal were obtained at 6,000 to 8,000 psi , 700 ° to 750 ° C , and a residence time of 30 minutes . With bituminous coal , yields averaging 0.4 wt pct of maf coal were obtained at 6,000 psi , 800 ° C , and 30 minutes ' residence time . With asphaltene and centrifuged residue , yields of less than 0.02 wt pct of maf coal were obtained at 6,000 psi , 700 ° C , and 60 minutes ' residence time .

Jan 1, 1964

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By Harold M. Smith

The data in this report were prepared to show how Bureau of Mines routine crude oil analyses could be used to evaluate crude oils in terms of common commercial products . The use of Bureau of Mines routine analyses to determine hydrocarbon - type relationships for the gasoline and gas - oil fractions is demonstrated . For this purpose the correlation index , the aromatic profile and the naphthene profile are used to establish reasonably acceptable values for hydrocarbontype relationships . The derivation and meaning of these indications are discussed . These analytical interpretations are applied to a group of high - sulfur crude oils from the Near East , the Permian basin of West Texas , Venezuela , Colombia , California , and other locations , and the resultant data for gasoline , gas oils , lubricating oils , and asphalt are compared by appropriate tables and graphs . Because the Near East crude oils contain higher quantities of paraffins in the gasoline and gas oil ranges , they will yield good , lowsolvency solvents and good kerosine , jet fuel , and diesel fuels , but straightrun gasoline of inferior quality compared to similar products from either West Texas or Venezuelan high - sulfur oils . The Near East oils also should be good sources of lubricating stock . However , when used as stock for catalytic cracking or reforming , the Near East oils suffer by comparison because they are deficient in naphthenes .

Jan 1, 1964

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By R. E. Lindstrom, D. J. Bauer

Studies were conducted to assess the potential of naphthenic acid as a fractional extractant for rare- earth mixtures and yttrium in sulfate solution . Naphthenic acid was an effective extractant , and separation factors were favorable in the presence of aqueous phase chelating agents . Addition of EDTA to the naphthenic acid extraction system resulted in average separation factors of 2.2 between adjacent yttrium- group elements , whereas DTPA resulted in average separation factors of 3.5 between adjacent cerium- group elements . EDTA was of value in separating yttrium from the rare- earth elements . Thorium and uranium were preferentially extracted over the trivalent rare- earth elements by naphthenic acid .

Jan 1, 1964

By J. H. Holden, C. C. Shale, G. R. Strimbeck, W. S. Bowie

Electrical characteristics of positive corona are presented for air in a 2 - in - diam electrostatic precipitator operating under dynamic conditions at temperatures of 600 ° to 1,500 ° F and pressures of 0 to 80 psig . Results show that current - voltage relationships depend solely on air density . Comparison of data on positive corona with previously published data on negative corona demonstrates a higher sparkover voltage and a wider range of operability for positive corona at temperatures above 375 ° F. The possibility of achieving higher voltages with positive polarity as indicated by these experiments implies several advantages for the use of positive corona in precipitators to allow better removal of suspended material from hot gases . Based on the physics of an ion in an electrical field , a theoretical equation is derived to define current - voltage characteristics of positive corona in terms of air density . Constants for the equation are evaluated from Calculated current - voltage values at different air densities agree reasonably well with experimental data .

Jan 1, 1964

By F. D. Everett

Thermoelectric and metal alloying applications have changed the status of tellurium from oversupply to under supply . In a search for new sources of this element in Arizona , Colorado , New Mexico , Utah , and neighboring states , the Bureau of Mines analyzed more than 200 samples and obtained the results of tellurium determinations by private companies on more than 500 samples from a wide variety of mineral - bearing deposits . The About 40 minerals containing tellurium have been reported , mainly tellu- rides of gold , silver , bismuth , mercury , lead , copper , iron , and nickel . minerals usually occur in small quantities and identification in ores is extremely difficult . Samples containing more than 0.1 percent tellurium were taken from the Hilltop and Memphis properties in Dona Ana County , N. Mex . , and the Silver King property in White Pine County , Nev . , where development was chiefly for base metals . The Lone Pine mine in Catron County , N. Mex . , and the Bambolla mine near Moctezuma , Sonora , Mexico are potential sources of native tellurium occurring in small but high- grade pods . Much of the production of tellurium has come as a byproduct of electro- lytic refining of copper and lead- zinc ores in Arizona , Colorado , New Mexico , and Utah . Base -metal ore deposits will continue to be the most important pri- mary source of tellurium , although the concentration in ores is nearly always less than 10 parts per million . Any significant increase in output of tellu- rium probably will be related to production and improved efficiency in smelt- ing and refining base - metal ores .

Jan 1, 1964

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By H. Kato, G. Asai, R. Blickensderfer, R. Siemens

Some relationships were established among crystallographic orientation , rollability , deformation texture , annealing behavior , slip planes , and ductile- brittle bend transition temperature of molybdenum single crystals . Six large molybdenum single crystals obtained from an ingot melted by electron beam were oriented by X - ray diffraction and rolled on crystallographic planes of low indices in a known direction . During room temperature rolling , cleavage occurred on 100 type planes . At 300 ° C the crystals were rolled to 95- percent reduction in thickness . The crystals ( 001 ) [ 110 ] and ( 011 ) [ 100 ] were most easily rolled . Pole figures were used to correlate the deformation textures of the rolled crystals with the initial crystallographic orientation . Several of the textures which developed could be explained as a rotation about a < 110 > axis of symmetry . The cube crystal ( 001 ) [ 100 ] retained much of its " cubic " orientation . The (001 ) [ 110 ] crystal developed the simplest texture , whereas the ( 211 ) [ 113 ] and ( 211 ) [ 120 ] crystals developed the most complex textures . The 1 - hour recrystallization temperature of the crystal ( 211 ) [ 113 ] was 700 ° C , which is about 300 ° C lower than that of commercial polycrystalline molybdenum . The poles of the slip planes ( as determined from gross slip lines at relatively low magnification ) tended to lie within 20 to 60 degrees of the pole of the rolling plane . The Knoop hardness was slightly dependent upon crystallographic orientation but more dependent upon rolling direction . The ductile- brittle bend transition temperature was dependent upon the rolling orientation and the dislocation density .

Jan 1, 1964

By F. R. Cattoir, R. E. Cumings

Columbium metal was electrorefined in a fused - salt electrolyte . Excellent results were obtained in lowering the impurity content in a 94 - percent columbium anode feed material to produce a 99.8- percent - pure metal . The reductions of the major impurities follow : Oxygen from 19,800 to 500 ppm , carbon from 9,700 to 25 ppm , iron from 9,200 to 630 ppm , nitrogen from 2,100 to 90 ppm , and silicon from 750 ppm to not detected . Columbium with a purity of 99.9 percent was produced from 99.5- and 99.8 - percent grades of columbium. The investigation was devoted to the evaluation of a fused - fluoride - salt electrolyte ( KF - NaF- K₂ CbF, ) for electrorefining columbium. The effects of the columbium concentration and the voltage upon the product's purity were investigated . The effect on the cathode current efficiency of ampere - hours of deposition and the formation of a dual valence state of the columbium was also investigated .

Jan 1, 1964

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By Charles H. Atkinson, Robert T. Johansen

Tremendous volumes of petroleum ( crude oil and natural gas ) at present cannot be recovered economically . The feasibility of using nuclear explosions for production stimulation therefore has been investigated . Data from underground nuclear tests conducted by the Atomic Energy Commission were reviewed , and the physical effects were evaluated for stimulating petroleum production . Calculations of the effect on ultimate recovery of increasing reservoir temperature with nuclear explosives showed disappointingly small increases . Production increases caused by fracturing of massive low- permeability reservoirs appear technically and economically promising . Petroleum reservoirs that might be converted from submarginal to commercial production are being located and evaluated as to potential reserves and as a location for a field test .

Jan 1, 1964

By L. H. Adami, E. G. King

The heats of formation of four sulfides --MnS ( alabandite ) , FeS ( hexagonal pyrrhotite ) , ZnS ( wurtzite ) , and CdS ( greenockite ) -- were determined by hydrochloric acid solution calorimetry . The heats of formation from the metals and rhombic sulfur at 298.15 ° K are , respectively , -51.01 ± 0.19 , -23.81 ± 0.24 , -45.86 ± 0.20 , and -35.70 ± 0.30 kcal /mole . The corresponding free energies of formation were calculated from the heats of formation and the pertinent entropy values .

Jan 1, 1964

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By D. Bienstock, J. H. Field, M. J. Lempel

A computer program is presented to perform the detailed and numerous calculations required for determining the interface temperatures and steady - state heat flow through a furnace wall composed of several refractories in layers . A method is developed that will allow the designer to determine the various thicknesses for each refractory layer to minimize either the total wall thickness or the cost of the wall per unit of area . A sample problem is presented and analyzed to illustrate the techniques involved .

Jan 1, 1964

By W. A. Stickney, J. W. Town

Studies on continuous - circuit leach - aluminum precipitation and leachelectrodeposition of mercury were made by the Bureau of Mines to determine optimum conditions and cost estimates for recovering mercury from mercury sulfide flotation concentrates . With 150 grams of sodium sulfide and 50 grams of sodium hydroxide per liter , from 98 to 99.8 percent of the mercury was extracted from flotation concentrates , with about 0.5 pound of sodium hydroxide used per pound of mercury produced . Precipitation of mercury from the caustic - sulfide solution with minus 8 - mesh aluminum shot required about 0.2 pound of aluminum per pound of mercury produced at a cost of $ 0.05 per pound of mercury . Electrodeposition cost with 7 mill power , based on 50 percent current efficiency , was below 2 mills per pound of metal deposited . Feed solutions ranged from 10 to 130 grams of mercury per liter , and current densities , from 2 to 70 amperes per square foot . The cost of open- pit mining 250 tons per day was estimated at $ 1.75 per ton , and flotation - leachingelectrodeposition of the ore , at $ 3.54 , resulting in a cutoff grade of about 0.1 percent mercury . The cost of underground mining 50 tons per day was estimated at $ 20.00 per ton , and the cost of milling the ore was estimated at $ 13.33 , which resulted in a cutoff grade of 0.6 percent mercury .

Jan 1, 1964

By E. C. Tarpley, R. A. Drogowski, R. F. Abernethy

Three of the test methods frequently used for the determination of moisture in the analysis sample of coal were employed in analyzing a series of coals ranging in rank from anthracite to lignite . For most coals , the variation between the three methods are within the tolerances allowed between duplicate determinations by the same method . The processing variables studied included atmosphere , flow rate of atmosphere , inert atmospheres , oven temperatures , heating time , exposure of the dried coal to laboratory air , and surface area of the test sample . Unless close control is kept on these variables , erratic results will be obtained .

Jan 1, 1964