Search Documents

By J. C. van Dyk

The objectives of this study were firstly to characterize and quantify the inorganic material in the Secunda gasification feedstock. Secondly, the effect of washing on coal properties and sulphur content was investigated. Coal from a single source and a coal blend from 6 different mines were tested. Composite samples were visually sorted by a geologist in the groups containing roof, floor, C-shale, pyrite, carbonates and siltstone material. Inorganic mineral types from the single source and coal blends were characterized separately. Characterization results indicate that the average mineral matter distribution (mass %) of the coal tested was as follows: carbonates (6%), carbon-shale (19%), pyrite (12%), roof (18%), floor (46%) and siltstone (22%). The roof, floor, pyrite, carbon-shale, carbonates and siltstone in the single source and coal blend have similar chemical properties and characteristics, except for the ash melting temperatures of pyrite and kaolinite in the siltstone. By implementing selective mining and increasing mining management practices, the percentage discard in the run of mine coal can be significantly reduced, by up to 45%, if the mining of roof and floor material can be avoided. No significant impact of mining practices on sulphur content is expected in this case due to the low concentrations of sulphur in the roof and floor material. In summary, selective mining practices will probably result in almost45% decrease in the discard content in the run of mine to gasification, an increase in the carbon content from 55.0% to 58% (air dry basis) and a decrease in sulphur content from 1.1% to 0.9% (air dry basis). It is clear from this study that the main source of sulphur is not in the high ash-content mineral types (e.g. floor and roof), but in situ in the coal structure. Keywords: inorganic material, effect of washing, roof, floor, pyrite, C-shale, carbonates and siltstone

Jan 1, 2005

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By M Lovitt, T Hewitt

The extraction of drawbells in Lift #2 at Northparkes Mines E26 orebody was achieved by single shot blasting, enabled through the use of electronic detonators. This paper discusses the designs considered at the time of the feasibility study and the various changes made to these designs prior to and during the construction phase of the Lift #2 block cave. Operational issues encountered are highlighted, as are ways in which these were overcome. The amount of personnel utilised to mine the drawbells is also covered. Lists of design and operational considerations to be used for drawbell extractions have been included.

Jan 1, 2005

By S Freij, P W, R Gunawan, D Zhang, B Feng

The Mt Whaleback iron ore mine is located adjacent to Newman, approximately 1200 km north of Perth, in the Pilbara District of Western Australia. Approximately 15 per cent of the waste materials are in the zones with high concentrations of sulfide and carbonaceous minerals and are referred to as æreactive shaleÆ. The reactive shale has the potential to undergo self-heating and can react with the ammonium nitrate (AN) based explosives used in mining operations, resulting in spontaneous combustion and spontaneous explosion. The sulfide-rich shales also have the potential to produce acid rock drainage (ARD). In the present study, over 200 shale samples have been collected from different locations in the Mt Whaleback iron ore mine, including blasthole drill cuttings, fresh mine faces and waste dumps. These samples have been systematically characterised for their geochemical properties. Based on the characterisation results, a pH test was developed as a cost-effective, fast and efficient tool for the assessment of reactive ground in the mining industry. This paper summarises the results of the sample characterisations and discusses the key findings arising from the interpretation of results. These results have significant implications in the safe storage of the reactive shales and the prevention of spontaneous explosion, spontaneous combustion and ARD.

Jan 1, 2005

By Robert Ditchburn

Within New Zealand?s extended EEZ there exists a vast submarine hydrothermal mineral resource associated with the Kermadec intra-oceanic arc. Along this arc more than thirty submarine volcanoes have been explored by GNS-lead researchers and, of these, c. 60% are known to be hydrothermally active and a site of active seafloor mineralisation. Assessment of whether this mineralisation is economically viable in terms of grade and tonnage is now underway. A key aspect of these investigations is determining the age of the mineralization which will have a direct bearing on its mode of formation, the time elapsed to amass an economic deposit and, ultimately, its capacity for sustainable extraction. Intact barite-rich ?black-smoker? chimneys similar to that depicted here (86 cm long) have been recovered from Brothers volcano in the southern part of the arc. These and other hydrothermal deposits provide evidence of active volcanic massive sulphide (VMS) mineralisation along the arc, the age of which can be determined from the disequilibrium between isotopes within the thorium or uranium decay chains. A chimney from Mariana arc has also been dated using these radiometric methods. The principle dating technique for chimneys up to 15,000 years old uses the decrease in 226Ra/Ba due to radioactive decay after the VMS was deposited. An initial ratio is obtained from chimneys that are proven to be less than 100 years old and this involves dating with 210Pb, 228Ra and 228Th that have short half-lives compared with 226Ra.

Jan 1, 2005

By Aly Mohammad, Dongyi Yue

"The design of rock sockets for drilled shafts and piles proves to be a challenge for the Design Engineer. The magnitude of loads on the shaft and the behavior of the rock are critical in determining the required socket length. Several acceptable methods are available in the literature to analyze a rock socket under a combination of axial loads, lateral loads and moments. This paper will present a state-of-the-art methodology to analyze rock sockets utilizing deformation characteristics of the rock. This design methodology was implemented in the design of a major project in New York City.The project discussed herein is a marine transfer station planned for construction at East 91st Street along the East River in Manhattan. In order to support the piers and platform structures at a site with relatively shallow depth of the bedrock, rock sockets were required for the drilled shaft foundations. Rock sockets were utilized to provide the required fixity to the foundations and the structures. Acting at the top of the rock sockets are large shear forces and moments created by the lateral loads transferred from the structure.Upon review of the available techniques, a simplified method was proposed and used to analyze the rock sockets with a significant magnitude of lateral loading. The method recognizes two mechanisms through which the lateral shear and moment are transferred to the rock; a) load transfer through horizontal resistance of rock and b) the vertical shear resistance of the bond between socket and rock.The first load transfer mechanism was analyzed using the p-y curve method based on a rock model developed by Reese. The second was analyzed using a bond stiffness derived from the formula and curves utilized in the AASHTO Specifications for calculation of rock socket displacement. By comparing the two mechanisms, the main contribution to the large horizontal shear force that developed in the rock socket is identified.The paper will present a summary of the design methodology utilized in determining the length of the rock socket. It is believed that the presented method will provide substantial cost saving in selecting the most economical and efficient design length."

Jan 1, 2005

By B Upton, J Mitchell

The use of hydro scaling and in-cycle shotcrete to replace conventional jumbo scaling, mesh and bolting as the primary method of ground control for run of mine development has been investigated through extensive trials at the Waroonga mine, Agnew Gold Mining Company.These trials have progressed from investigating the productivity aspects of the method through to a three month mine-wide trial, which may yet lead to the adoption of this potentially best practice ground control technique at Agnew.Ov erseas trials and research have shown that hydro scaling results in a significant improvement in the shotcrete-rock bond strength. Good adhesive bond strength ensures that the shear strength of the shotcrete layer rather than itÆs flexural or tensile strength is fully mobilised as rock mass reinforcement.This maximises shotcretes ground reinforcement capability and it is suggested that a bolt-less fibrecrete support design is feasible using the hydro scaling technique.

Jan 1, 2005

By Tony D. Canale, Anthony Mazzo

"Times Square, arguably one of the best-known destinations in the world, has undergone and continues to undergo a re-development aimed at attracting corporate tenants to the area. Mueser Rutledge Consulting Engineers (MRCE) was involved with the planning, design and construction of the foundations for the Conde Nast and 5 Times Square sites, as well as Times Square Tower. These sites are pictured in Figure 1.This paper will focus on the design and construction of the deep foundations for Times Square Tower that was developed by Boston Properties. PROJECT DESCRIPTIONTimes Square Tower is 47 stories tall, with no setbacks and an overall height to top of crown of 730 feet (222.5m). It has two basement levels extending 30 feet (9m) below grade over the full site. As shown in Figure 1, the structure occupies the entire site and has a footprint of 22,000 square feet (2,044 m2), with a total rentable area of about 1.2 million square feet (111,480 m2). The planned use for the building is office space with retail at the ground level. When completed, Times Square Tower was the final building constructed as part of the Revitalization of Times Square. Due to the site constraints, designing and constructing the foundations was akin to placing the final piece of a puzzle.Times Square Tower provided numerous design and construction challenges that were a result of tight working conditions, heavy column loads, and a compressed schedule.GEOLOGIC SETTING AND SITE HISTORYThe Times Square area is part of the Manhattan Prong called the Manhattan Ridge, a formation of old and durable metamorphosed and folded bedrock, now termed the Hartland Formation. The bedrock generally has a thin soil cover and uneven surface overlain in some areas with a thin mantle of decomposed and/or weathered rock. Overburden soils include glacial and post-glacial deposits and recent fills.Transit improvements have been made in and around the Times Square area since the early 1900’s. The 1, 2 and 3 Subway Lines that run below 7th Avenue were constructed circa 1915 using cut and cover techniques and extend about 28 feet (8.5m) below grade. The N, R, Q & W Subway Lines that run below Broadway were also constructed in 1915 using cut and cover techniques and extend about 38 feet (11.6m) below grade. The 7 Line that runs below 41st Street was constructed later, using both cut-and-cover and tunneling methods as it runs below the other subway structures at a depth of about 55 feet (16.8m) below grade."

Jan 1, 2005

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005

By C. Andrews

Fuel cell testing requires fully automated operation, on-site configuration of tests, and real-time monitoring for performance and failures. Balancing the flexibility and programmability of a test station with reliability, cost, and user interface can be a daunting challenge to the test equipment engineer. Endurance testing of fuel cells requires the highest level of reliability for test stand hardware and software without compromising automation capabilities or users interface. Techniques for implementing an ultra-reliable test platform addressing hardware limitations, sophisticated watchdog monitoring to prevent inadvertent shutdowns, and software limitations (e.g., balancing a highly-functional graphical users interface with reliability) are presented.

Jan 1, 2005

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

Mr Chairperson, respected leaders of the mining industry, ladies and gentlemen;   Good morning, Kiora, Nihao.   I am very honoured to give a speech to the 2005 New Zealand minerals conference. I would like to take this opportunity to express my sincere thanks to the Ministry of Economic Development to invite me to be part of this important event.   Today, I am going to talk about two themes: a brief introduction of ChinaÆs economic development, including ChinaÆs energy strategy; the good bilateral relations between China and New Zealand, its potential for further development and its relevance to our cooperation in the field of minerals and energy.   It is a well-known story that over the past 27 years, great changes have taken place in China. In 1978 when ChinaÆs reform and opening up just started, its gdp was near to only 150 billion usd dollars. By the year of 2004 it reached to 1.6 trillion usd, an average of yearly growth rate 9.4 per cent.   ChinaÆs great achievements are widely appreciated both in China and abroad. ChinaÆs development has not only improved the living standard of its own people, but also produced a huge market and brought about great opportunities for the world. Since ChinaÆs entry into WTO in 2001, China has imported near to 1.8 trillion usd dollars of goods, averaging a yearly imports of 500 billion usd dollars, creating for other countries and regions more than ten million jobs.   Our prediction is that in the next five years, ChinaÆs imports will be well over three trillion usd dollars. China will continue to serve as one of the leading growth engines for the future world economic development. Now China is on its great strive to achieve the goals of improving living standard for all the Chinese people. We are trying to reach a quadruple gdp of 2000 by the year of 2020, namely to reach gdp four trillion usd, a gdp per capita 3000 usd dollars.

Jan 1, 2005

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By P Rourke

In this climate of increasing demand for commodities, it is becoming necessary to expand and optimise existing bulk material handling facilities in order to increase capacity to satisfy demand. Production capacity in these facilities is often adversely impacted during the expansion process. A successful and proven strategy to reduce this impact is to bring the additional capacity online in stages coinciding with routine maintenance or other short shutdowns. Compatibility of the automation systems with staged upgrades in capacity is the key to achieving a successful outcome. Since 1994, Hatch has been researching a generic, highly configurable product transport control system that can be reconfigured to cater for plant expansions or modifications without incurring significant risk to production capacity. In 2002, BHP Billiton Iron Ore (BHPB IO) recognised the need for such a generic Route Selection and Sequencing (RSS) system and engaged Hatch to build a generic RSS system as part of the $US351 million BHPB IO Products and Capacity Expansion (PACE) project. In 2004, Hatch successfully deployed such a generic configurable control system at BHPB IO Port Hedland Ore Handling Facility. This generic system is known as the Hatch Product Transport (HPT) System.

Jan 1, 2005

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

By V Gupta, Z Huang, S K. Biswal

G-Cell is a new design modification of the Imhoflot pneumatic flotation technology, which utilises a self-inducing aerator inside a downcomer, where bubble-particle attachment takes place. The present study has investigated the suitability of the G-Cell technology for cleaning fine coal using a 0.8 m diameter prototype unit at a coal preparation plant operating in the Midwestern United States. A slip-stream obtained from the overflow of raw coal cyclones operating in the plant, containing nominally minus 150 micron size particles and having ash content in the range of 40 per cent to 50 per cent and sulfur content in the range of 1.30 per cent to 1.50 per cent, has been used as the feed for the G-Cell. The performance data produced from the G-Cell tests are found to be very close to the ideal performance curves produced from release analysis. A statistically designed experimental program has been conducted to investigate the parametric effects on various key process responses, such as combustible recovery, product ash and sulfur rejection. The empirical models developed in this study have been utilised to identify a suitable experimental region for achieving a desired combination of response targets.

Jan 1, 2005

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By Judy B. Jones, Bradley A. Crenshaw, Theodore DePooter

This paper reviews groundwater issues leading to a secondary grouting program at the Chattahoochee Tunnel that was implemented subsequent to the contact grouting program. The secondary grouting program was developed based on infiltration data, geology, and testing programs. This paper includes a brief description of the geological features encountered, as well as describing the grouting program. The success of this grouting operation has been quantified by several methods, and is presented to help others project the costs and benefits of this type of program. Review of initial results and refinements of techniques are also discussed.

Jan 1, 2005

By N. Roqueñí, J. Loredo, F. Pendás

Impacts of mining on surface water and groundwater occur frequently not only in active mines but in abandoned mines, then the establishment of effective legal mechanisms for the regulation and control of mine waters is a necessary step in order to avoid pollution from mine waters and in consequence to contribute for a sustainable development of the mining industry. Currently there is a lack of a specific European legislation about mine waters and this absence of legislation occurs too at national level in many European countries. This absence of an European specific regulatory framework for mine water pollution questions the effectiveness and the applicability of the current legislation and this fact has led the EC to put forward proposals legislation to adequately deal with environmental and social consequences of mining, and among those proposals is a draft for a directive on waste from the extractive industry that includes provisions for mine water pollution.

Jan 1, 2005

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005