Search Documents

By Khaled Morsy

Most of the available numerical codes simulating the reinforcing effect of fully grouted bolt are accomplished by a series of bar elements which are connected along their length to the host rock by shear springs and sliders. The spring-slider system represents the shear bonding effect between the bolt and the host rock. This paper describes a three dimensional finite element modeling technique for the 3D simulation of fully grouted bolt reinforcement. The proposed technique introduced a physical simulation for the fully grouted bolts. The bolt simulation is composed of a series of beam elements (representing the steel rebar) embedded in brick elements (representing the grout). Because of the complexity of the grout/rock interface, ABAQUS explicit code was used. A modification of the ABAQUS default friction model was conducted to consider the cohesion of the grout/rock interface. The interaction between the grout and the host rock is simulated by the modified friction model. To verify the proposed technique, a simulation of the pull out test we conducted. The results from the simulation were compared with former studies

Jan 1, 2004

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context in which they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage such as nuclear power generation where international cooperationis eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit its mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2004

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By I. A. Minaev

The conditions of a stability of metallurgical films on a surface of solid on the basis of classical regularities of a thermodynamics are considered. For specific conditions of metallurgical processes the basic equations relevant to non-metallic inclusions (product of steel killing) migration and transfer through the interface boundary of metal-slag are obtained. The basic criteria equations of conditions of stability of metallurgical dispersed systems are developed in view of films formation. The probable thermodynamics reason of wetting due to formation of stable films are discussed. The experimental measurement of thin and thick films elastic resistance for metallurgical systems are carried out and the results are discussed. The presence of a wetting thick film increases stability of dispersed systems (facilitates an inverse implication of non-metallic inclusion in a melt) due to a barrier effect of wetting films. The quantitative evaluations of non-metal inclusion stability for steel in contact with any metallurgical slag are carried out. The results are in accordance with technological experience. Keywords: Inclusion removal, Film thermodynamic, Slag-metal dispers system

Jan 1, 2004

By M. Pearson, L. Zunti

Pressure vessels in hydrometallurgy and many chemical process industries throughout the world require the use of specific lining systems to protect the parent vessel materials from corrosion and/or abrasion. Typically, these lining systems are required for processes that are corrosive and operate at elevated temperatures. Two basic lining system types arc: 1) refractory linings in conjunction with an impervious corrosion resistant membrane, and 2) metal-clad vessels consisting of titanium or other corrosion resistant metal bonded to a carbon steel shell. Operating conditions play a key role in selecting the type of lining system to be utilized for a specific application. Lining systems in turn have an impact on the process vessel size, which ultimately affects the capital cost of the vessel. The capital costs for each type of lining system must be considered for each application, as well as maintenance concerns, quality control, and delivery. It is clear that operating conditions play a key role in the final selection of lining systems utilized for specific projects based on initial capital cost, life-cycle maintenance costs, and overall service life. This paper will examine the fundamentals of each lining system, their inherent technical strengths and weaknesses, and present relative cost comparisons for each lining system as they apply to specific operating conditions and vessel sizes.

Jan 1, 2004

By J. Jonas, J. M. Harrington, K. Wangerud, S. D. Fundingsland, J. G. Harrington

EPA NRMRL Mine Waste Technology Program and Region VIII Superfund office are jointly conducting an in-situ technology demonstration at the Anchor Hill Pit Lake, Gilt Edge Mine Superfund site. The goal is to develop in-situ treatment cost/performance data for potential application in long-term water treatment/management at Gilt Edge and similar sites. The pit contained 77,000,000 gallons of pH 3water with elevated metals, sulfate, and nitrate. The Green World Science® patented process for in situ treatment was implemented to isolate and sequester metals; create stable long-term water quality and restore a sustainable ecosystem. COCs have decreased more than 99%, and dissolved discharge standards were attained.

Jan 1, 2004

As the mining industry looks to new technologies for a safe work environment and increased production rates, so should emergency response teams when dealing with organisational incidents. Implementation of technology has transformed the nature of incidents within the international mining community with lower frequency, high impact events replacing high frequency, low impact incidents of the past. In turn the approach to mines rescue response and preparation has naturally diversified. New rescue technologies when applied effectively can only further advance preparation and the response of mine rescues teams. This paper discusses some of the changes associated with mines rescue as the industry embraces technology. It highlights some recent rescue responses and their approach and gives examples of some of the new technologies being used for improved mines rescue.

Jan 1, 2004

OPENING SESSION Session Chairpersons: Dr. P.P. Jourdan & Dr. L.A. Cramer Transformation to Tackle the Challenges Facing the Ferro Alloy Industry in the Next Decade R.J. Linnell Electricity Supply in SA ? A 10-Year View T.S. Gcabashe IDC as the Catalyst for Growth in the South African Ferroalloys Industry J. Kriek Development in the Global Stainless Steel Industry V. Muñoz CLOSING SESSION Session Chairpersons: Mr. R.J. Linnell & Dr. O.F.R.A. Damm The Health of Vanadium T.E. Jones Steel Raw Materials - Nickel, Chrome, Stainless Steel Scrap and Manganese H.H. Pariser

Jan 1, 2004

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By G. Velarde

Agglomeration has as main objective to form a uniform and highly permeable heap for leaching. An inaccurate dosage of moisture during agglomeration leads directly to poor agglomerate quality and segregation of particle sizes during stacking. This causes a heterogeneous distribution of the leach solution inside the heap which invisibly and practically permanently affects the recovery. Unfortunately, only when this becomes serious and the mineral contains an excess amount of fine particles and/or clays then the poor permeability of the pile becomes obvious. This paper is based on the experience of Minera Cerro Verde in the development and application of a quantitative method to control moisture during agglomeration. As the amount of fine particles/clays varies, the quantity of moisture has to be altered in real time. The measurement of agglomerate electrical conductivity is used for it. This concept is based on the sharp change seen in conductivity when the mineral passes its absorption limit. A liquid conductive film then begins to form over the surface of the particles, which leads to the formation of agglomerates through liquid bridges, which are also electrical bridges. Moisture is adjusted to reproduce a value of conductivity established previously and is the guiding parameter. Moreover, moisture amount added to reach this conductivity parameter provides information about the fines/clays relative content for best leaching management.

Jan 1, 2004

By Liangtian Liu, Tie Ou, Guangqiang Li, Chenghuan Yu

For stabilizing the production of containing nitrogen steels, a study on nitrogen absorption behavior of killed molten steel has been carried out by means of the RH vacuum device in which nitrogen was used as a driving gas. The results showed that there was an increase of nitrogen content in molten steel under vacuum processing but the rate of nitrogen absorption was slowed down by the surface active elements. Therefore, a kinetic equation for nitrogen absorption of molten steel with apparent first order reaction was derived by constructing a modified model in which the adsorption of closed surface site was taken into account. The experimental results confiimed that the calculated values agreed with the observed ones. This model is suitable for the prediction of nitrogen adsorption operation for containing nitrogen steels.

Jan 1, 2004

By A. Alfantazi

Recently, titanium and its alloys have been the materials of choice for the liner and internal components of autoclaves used to extract Ni and Co from laterite ores. There have been many corrosion incidents ranging from localized attacks due to scale formation or welding, to damage caused by pockets of concentrated acid. Most of the literature focuses on methods to avoid the corrosion altogether. Little has been published to increase awareness of the chemistry at these conditions. For this paper, a literature review of the thermodynamics of titanium was undertaken to decipher the slew of information available. E-pH diagrams were constructed from select data and compared with the results of electrochemical experiments. Since nickel laterite leaching takes place in sulphuric acid, and in many cases chloride concentrations are very high, the Ti-H2O, Ti-Cl--H2O and Ti-SO4---H2O systems were considered.

Jan 1, 2004

By F Jiao, J Wang

By the year 2000, China was the sixth largest gold producer in the world, with about one-quarter of total production being derived from refractory or semi-refractory deposits. Although bacterial oxidation plants had been previously tried in China using local technology, these plants had not been commercially successful. The Laizhou Gold Enterprise (Tarzan BioGold Co Ltd) located in Shandong Province, undertook to modernise their gold processing facility in 2000 with the introduction of Bacterial Oxidation (BACOX) Technology. In 1997 BacTech Australia and Mintek of South Africa had formed a technology partnership, combining forces in the provision of bioleach technology. Under a cooperation agreement, BacTech/Mintek were chosen as the preferred technology providers for this first application of commercially proven bacterial oxidation technology within China. The paper describes the successful operation of this plant over the last three years. The events of project implementation are described, from the metallurgical testing of concentrate; through to the commissioning at the design throughput of 100 tonnes per day resulting in 80 000 ounces (2.5 tonnes) per year of refined gold. Process aspects of the operation encountered over the last three years are discussed which illustrate the robustness of the operation. The success of the bioleach facility has led to an advancement of plans to double plant capacity and some of the innovations, which may be employed in this expansion phase, are discussed.

Jan 1, 2004

By Jonathan Tsang, Ali Merati, Jonathan Beddoes

Due to economic factors, many aircraft in service today have been operating for more than 30 years even though they were initially designed with a service life of 20 years. Improved damage management models are therefore needed for use in life prediction and management of the aging fleets of aircraft. Currently, the generally accepted procedure in fatigue life prediction methodologies is to back calculate the equivalent initial flaw size (EIFS) using established long crack growth data. However, it was observed from studies carried out at the National Research Council Canada that nucleation and short crack growth constitute up to -95% of the fatigue life. As a result, it seems that the significance of the short crack regime has been underestimated and must be further investigated and fully understood before an accurate holistic life prediction methodology can be realized. Unlike long cracks, local microstructural features such as grain boundary, grain size, inter-particle spacing, and texture play dominant roles in the behavior of short cracks. An extensive study has been carried out to evaluate different crack detection and monitoring techniques in the short crack regime for AA2024-T3. The results will be presented in detail.

Jan 1, 2004

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By J. H. Potgieter

This paper describes two cases of corrosion that occurred in dry-process, rotary, cement-clinker kilns. In the case of the kiln with five pre-heater stages, the attack occurred primarily from sulphates that probably originated in the raw feed and fuel being used in the plant and that penetrated the refractory lining. The corrosion was similar to ash-deposit corrosion often observed in steam boilers. In the second case the plant consisted of a long dry kiln with a single pre-heater fitted to the feed-end. In this case the corrosion could be ascribed to alkali chloride penetration through the refractory-brick lining and subsequent hot corrosion of the kiln shell.

Jan 1, 2004

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004