Search Documents

By K. Heid

"Although concentrated efforts have been made to deplete PCB transformers from the Canadian environment, numerous transformers (as well as ballasts, capacitors and magnets) continue to exist throughout the Canadian mining industry. The existing installed base is slowly being phased out as environmental issues come under increasingly high profile. The following article identifies the potential problems of owning PCB transformers and offers some solutions for their removal, disposal and replacement. IntroductionPolychlorinated Biphenyls (PCB) are synthetic chemical compounds consisting of chlorine, carbon and hydrogen. PCB was widely used in transformers due to its physical properties, including stability, low flammability and non-conductivity. Use of PCB in electrical equipment has been banned since 1977 when the extent of environmental contamination was discovered.Although PCB’s have been outlawed for use in electrical equipment since the late 1970s, safe storage regulations were not addressed until 1988 when a major spill prompted the federal government eventually to issue the storage of PCB Material Regulations in 1992. These regulations replaced the Interim order of 1988 under the Canadian Environmental Protection Act.PCB transformers are usually referred to as askarel filled transformers or as PCB contaminated mineral oil transformers. Askeral transformers were designed to contain high concentration PCB fluids, referred to as askarel. Mineral oil transformers were not designed to have PCB concentrations but were inadvertently contaminated during manufacture or maintenance activities."

Jan 1, 1998

By Pigdon SP, Anderson RM

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of I MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998

By Neil T. Davie, Thomas K. Blanchat, Thomas C. Togami, Joe R. Weatherby, Dale S. Preece, Robert A. Benham, James J. Calderone

"Geotechnical structures ,such as underground bunkers, tunnels, and building foundations aresubjected to stress fields produced by..the gravity load on the structure and/or any overlyingstrata. These stress fields may be.. reproduced on a scaled model of the structure byproportionally increasing the gravity field through the use of a centrifuge. This technology canthen be used to assess the vulnerability of various geotechnical structures to explosive loading.Applications of this technology include assessing the effectiveness of earth penetrating weapons,evaluating the vulnerability of various structures, counter-terrorism, and model validation. Thisdocument describes the development of expertise in scale model explosive testing ongeotechnical structures using Sandia’s large scale centrifuge facility. This study focused onburied structures such as hardened storage bunkers or tunnels. Data from this study was used toevaluate the predictive capabilities oft existing hydrocodes and structural dynamics codesdeveloped at Sandia National Laboratories (such as Pronto/SPH, Pronto/CTH, and ALEGRA)."

Jan 1, 1998

By Hung Tran, Qian Liu, Patrick Andrieux, Dave Counter

Blast damage in open stope mining has been an important concern in controlling ore dilution. Severe damage to the surrounding rock mass can result in the caving of waste rock and/or backfill materials, as well as general instability of the ground. The blast damage study conducted at Kidd Mining Division in 1995 was aimed at measuring the damage zone around blastholes and at identifying other factors which influence the damage. An approach and methodology developed mainly by Blastronics, together with Noranda under a project with the Mining Research Directorate, was adopted for this project. The principle was to combine vibration measurement results with borehole camera observations to derive the blast damage criteria at the specific site. The Holmberg-Persson Equation was used for the regression of near-field vibration data. The damage criteria was examined with both borehole camera observation results and rock elastic and mechanical properties. Details of this methodology, including instrumentation, are reviewed in this paper and an implementation case study of the blast damage evaluation is presented.

Jan 1, 1998

By Cai S, Zhou C

The requirement of mineral resources is increasing as the economy is continually increasing in China. The mining practices of various complex sulphide deposits and precious metal deposits, and the treatment of mine tailings and other industrial solid wastes, have greatly improved fill quality in the metal mines. From early-1980s, high density slurry fill, paste fill of total tailings, low density slurry fill with addition of silicate gelling agent, etc has been studied and applied, and some progress has been achieved. Today, mine tailings, slag and power plant ash are widely used as fill materials in mining. A number of cemented fill mines equipped with large capacity trackless mining machines are in production. Recently, The 3rd Chinese National Symposium on Mining with Backfill, 1995 has been held, the progress of fill technology in mines has been exchanged and summarised. In the paper, some aspects of fill technology used in the metal mines of China are briefly introduced and some applications of fill research work are presented.

Jan 1, 1998

By John Watson, Jay Rodgers

The world of blasting and explosive use continues to evolve into one which relies heavily on measurement, quantification, process control, and information feedback as a means of contributing to operational improvements. More than ever good blast performance, once thought to be a result of someone’s “artistic ability”, is giving way to “hard science” and measurement techniques. Variability in product performance and process control is becoming less tolerable with increasing environmental issues, regulatory pressure and public awareness.

Jan 1, 1998

By H. Para, A. Aguirre, G. Artadi

Mining is a very important economical activity in Peru which has been recently developed without considering environmental aspects. Here, we show an experience at the Milpo mine, situated 4,200 meters above sea level; a mining company that has the value of being one of few from the last decade that is engaged in consolidating a model of environmental protection. The model includes aspects of contamination prevention and control, with bioindicators such as pasture cultivation, vegetables, forests, and hydrobiological species breeding. Socially, through means of development programs in natural areas, forestation and support to rural agriculture, together with environmental education, it is being demonstrated that it is possible to ensure tangible results in environmental conservation and the well-being of the populations around the mine.

Jan 1, 1998

By Dale A. Sketchley

"Abstract - Large differences in gold content between rock fragments or small volumes of unbroken rock, commonly referred to as the nugget effect, are related to sample and subsample weights, crushing and pulverizing sizes, and density, shape and size distribution of gold grains. Gy’s sampling theory, which relates gold grain characteristics to sample weight, fragment size, and error, provides a method of estimating a sampling constant that quantifies deposit characteristics that contribute to the nugget effect.Sampling control tests provide methods for determining the sampling constant. Sampling control charts, comprising nomographs that relate sample weight, error and particle size, use the sampling constant to optimize sample weights and comminution sizes, and to minimize the variability introduced by incorrect or inadequate sampling and sub-sampling procedures. The sampling constant is useful in classifying ores into arbitrary categories according to expected sampling difficulties. Spatial variations in the sampling constant can be used to aid in defining ore types for modeling geological domains, which should have unique sampling protocols. Examples that illustrate the relationship between the sampling constant and expected sampling problems, and the spatial variation of the sampling constant, are given for various deposits. Case histories of sampling programs are presented.Quality control procedures consist of monitoring sample contamination amd accuracy and precision of analytical results. Accuracy, precision and contamination are monitored by including standards, duplicates and blanks into batches of samples being analyzed. Analytical results of standards and blanks are plotted on a batch-and-time basis with control lines at plus or minus two/three standard deviations as confidence limits of the accepted round-robin value. Examples are given that illustrate a laboratory system in statistical control and the various types of problems encountered when interpreting quality control data. These include sample transcription errors, degradation, contamination, sampling errors, detection limit problems, instrumental drift, lack of statistical control, laboratory bias, procedural problems and data tampering.Where bias is negligible, precision, as a function of concentration, can be obtained from duplicates using the Thompson-Howarth precision algorithm, which also allows calculation of the practical detection limit. Examples are given that illustrate variations in precision, with grain size, for different types of duplicates, as well as mineralogical changes and sampling errors."

Jan 1, 1998

By D. Eugene Rannels, Yu-Chen Lee, John W. Swisher

"Inhaled dust particles of appropriate size contact cells of the alveolar region.' The acute response to coal dust appears to involve a variety of cell types, including alveolar epithelial cells, interstitial fibroblasts, both resident and recruited macrophages, and cells of the immune system. Direct and indirect effects of dust, which may be mediated by soluble factors,'' can initiate acute and long-term lung injury. While it appears that epithelial cell growth and differentiation, along with integrity of the epithelial basement membrane, may play a role in the long-term response to dust exposure, little is known of the role the alveolar epithelium may play in the progression of injury. The broad hypothesis that underlies these experiments is that short- and long-term consequences of coal dust exposure involve changes in structure and function of the alveolar epithelium and the underlying extracellular matrix. Recent studies show that coal dusts exert direct effects to modify pulmonary epithelial cell-extracellular matrix interactions in vitro.3EXPERIMENTAL PROCEDURESType II cells isolated on day 0 by density centrifugation and differential attachment4 were plated overnight in D MEM containing 10% fetal calf serum before exposure to anthracite dust PSOC 867 sonicated into culture medium (750 ug/mL).3 Synthesis of extracellular matrix proteins was determined on day 3 of primary culture, as detailed elsewhere. 5 Cells were removed from extracellular matrix by extraction with NH4OH and high salt. Extracellular matrix synthesis and fibronectin content were evaluated based on radiolabeling with 3 H-leucine and on Western blot analysis, respectively. Additional analytical methods and calculations are detailed elsewhere.3-5"

Jan 1, 1998

By Jae-Chun Lee

One of the main advantages of the supported liquid membrane(SLM) would be that different kinds of ions can be extracted selectively or simultaneously from multi-component solutions by parallel treatments with multi-SLM units. This distinctive feature of the SLM extraction is originated from its non-dispersive contacting operation between organic and aqueous phases. In this study, simultaneous and selective extractions of zinc and copper ions from their mixed solutions have been demonstrated using two parallel modules of SLMs. PC88A and LIX84 were used as the extractants for zinc and copper, respectively, and the Hoechst Celanese hollow fiber modules(Liqui-Cel Lab Module) as the supporters. The performance of the simultaneous system was compared with those of the system in which the extraction of each component was achieved by individual runs

Jan 1, 1998

By E. De Souza

Rockbursts and rockfalls cause very large safety and productivity losses in underground mines. One of the major unsolved problems of safe, economical rock support in underground mining has been that of maintaining anchorage during dynamic rock loading conditions or seismic related occurrences. It is recognized that the large displacements and high strain rates in excavation walls and underground structures cannot be countered by increasing the strength of stiff rock-reinforcing systems but must be accommodated by introducing yieldability into the support elements. This paper introduces a low cost yieldable support system which provides viable solutions to dynamic support loading. Such system should not only provide a feasible and more effective rock mass stabilization strategy but improve mine safety and reduce losses.

Jan 1, 1998

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By P. C. Hollick

Two marine diamond deposits on concession 2b off Namaqualand along the South African Coast, have been systematically mined over the past year by the mv Moonstar. The two deposits, Smith?s Ulcer and Wedge Point Basin, are comparable in morphology, straddled the same water depths and have similar geology yet have given very different recoveries when compared to their respective grade models. These differences are best ascribed to the different style of mineralisation observed within the two deposits which has been directly controlled by the bedrock morphology. The smith?s Ulcer deposit has been formed in a metagreywacke bedrock displaying a strong north-south trending foliation which dips steeply to the west. Consequently the mineralisation is confined to narrow north-south linear trends with limited lateral extent (less than 5m) making extraction extremely difficult and somewhat variable. RE factors (recovered grade versus estimated grade) for this deposit range from 0.5 to 1.1. The Wedge Point Basin deposit is formed in a micaceous metaquartzite with a conjugate southwest northwest joint set, the southwest lineation being the more prominent, and structural foliation dipping gently to the west. The resultant style of mineralisation is confined to basinal features defined by topographical lows and is fairly lateral in extent (in order of 50m). Extraction of the mineralisation from this deposit is less arduous with recoveries more uniform, RE factors are frequently in the range 2 - 3. This style of mineralisation is more in line with what is to be expected from marine alluvial deposits, the nugget effect of diamond concentration being responsible for the high RE factor. The long narrow linear trends observed in Smith?s Ulcer demonstrably require a specialised approach in successfully sampling, modeling and ultimately mining.

Jan 1, 1998

Maximising margins in highly competitive international markets demands superior productivity. A key to superior productivity is using a process approach to enable rapid, ongoing improvement of production, commercial, administrative, marketing

Jan 1, 1998

By M. Misra

The removal of lead and other heavy metals present in an active US Army small arms firing range soil was evaluated in a pilot scale test program at Ft. Polk, Louisiana. Two different acid based extraction processes in conjunction with conventional physical separation methods were used. Physical separation processes consisting of screening and gravity operations removed most of the coarse lead particulates and slugs. Hydrochloric acid leaching followed by precipitation of lead as hydroxide recycled clean soil containing less than 500 mg/L. total lead and less than 5 mg/L TCLP lead. Lead extraction efficiency with hydrochloric acid was 96 percent. The results of lead removal by physical separation in conjunction with acetic acid leaching were not consistent over the whole test period and the total soil processed.

Jan 1, 1998

ITEC Environmental Colorado has begun reprocessing the tailings from old mining sites near Boulder, CO. And if the technology behind ITEC's pilot project at Gold Hill proves successful and profitable, the company plans to launch similar reprocessing operations in other parts of the state. The pilot project is under the watchful eye of state and federal authorities. They hope the technology becomes the answer to cleaning up old mining sites throughout the West. Remining and environmental cleanup on an economic basis, then, are ITEC's hopes in one the most environmentally conscious counties in the state. Clean up the mine dump sites and recycle the land, for a profit. In June 1998, ITEC Mineral Inc., ITEC Environmental Colorado's Canadian parent, acquired the Gold [ ] Hill Mill facility in Boulder County. Included in the acquisition was 4.4 hm2 (11 acres) containing the Gold Hill Mill and 283 hm2 (700 acres) of additional properties adjacent to the facility. ITEC estimates that there are about 910 kt (1 million st) of dump rock in the area. That is enough to make the operation viable. ITEC will sell the metals recovered through its reprocessing operations. However, due to low metals prices, ITEC is not expecting to make much money on the recovery of precious and base metals. Instead, the company plans to resell the reclaimed land for residential and commercial development or open space. The Gold Hill Mill site is the first of 17 sites in Colorado that ITEC Mineral hopes to clean up and recycle the land. Most notable among the sites is the historic Central City/Black Hawk mining district, which ITEC believes holds considerable potential. The Gold Hill Mill is located 14 km (9 miles) west of the city of Boulder and less than a half mile from the small town of Gold Hill. The mill was. last operated in 1992. The operation was forced to close that year due to environmental and cash flow problems. Gold Hill is in the middle of a region with more than 32 Mt (35 million st) of mine tailings. Independent geologists have' established the average grade of the Gold Hill mine tailings to be 4.5 to 5.3 g/t (0.13 to 0.155 oz/st) of gold and 28 to 44 g/t (0.83 to 1.29 oz/st) of silver. According to these studies, the Gold Hill mine tailings are five times richer in precious metals than the tailings of the Norebec Manitou property in Canada that ITEC is also remining, reclaiming and restoring. Upon acquiring the mill, ITEC undertook a refurbishing program that included adding a second ball mill. This increased the Gold Hill Mill's capacity to 180 t/d (200 stpd). The operation employs 15 people. "The Gold Hill Mill site will demonstrate the efficiency of our integrated remining, reclaiming and restoration process," said Maxine Stewart, president of Denver, CO -based ITEC Environmental. "The abundance of similar mine sites in Colorado presents a number of opportunities to bring the benefits of the ITEC system to other communities around the state." Holly Huyck is technical advisor to the Clear Creek Watershed Advisory Group. She said: "ITEC is cleaning up an orphan mine site that otherwise would continue to contaminate the Boulder Creek watershed with acid and excess metals. This is a win-win situation: ITEC gains marketable minerals while it reclaims mined land and helps to improve the watershed."

Jan 1, 1998

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

The paper presents the results of laboratory blasting and grinding experiments on a low-grade iron ore, investigating how blasting will influence the subsequent crushing and grinding operations. Increased blasting energy will lead to a reducti

Jan 1, 1998

By R. G. Reddy

Solid state reduction of roast movat chromite ore with carbon was carried out as a function of C/FeO ratio and temperature in the range 800°C to 900°C by thermogravimetry analysis (TGA). A two stage mechanism, (1) the reduction of FeO present in Roast Movat with carbon monoxide; and (2) the regeneration of CO by the oxidation of carbon with CO2 was proposed. The rate controlling step is the carbon oxidation reaction. A kinetic equation, that of random nucleation, was proposed. The activation energy for the reduction was determined to be 55800 J/mole and is compared to those activation energies determined for other chromite ores.

Jan 1, 1998

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998