Search Documents

By Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky, and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought, but rather 20° in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Jan 1, 1997

By T Barnes, K D. Sexton, T J. Tope

For the past decade, the U.S. Department of Defense (DoD) has been under increasing pressure from state and federal regulatory authorities to develop management strategies for waste streams generated at its bases, installations, and ranges. Since passage of the Federal Facilities Compliance Act (FFCA) in 1992, concerns have focused in particular on military munitions and energetic waste streams.

Jan 1, 1997

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By R. G. Eggert, M. R. Walls

A mining CEO's willingness to participate in risky investment opportunities significantly affects a company's strategic-investment decisions. Decision-analysis techniques provide a mechanism for measuring a CEO's risk tolerance and ability to make formal comparisons of risk propensity among mining firms. The authors developed a methodology for measuring CEO risk tolerance. The findings from a confidential survey of mining CEOs are presented. The results from the survey suggest that: •mining CEOs are overwhelmingly risk averse when considering investment decisions; •CEOs of small mining firms are significantly more risk averse than CEOs of large mining firms; and •there appears to be some differences between Australian and non-Australian CEOs regarding their willingness to participate in risky investments. The results of this survey suggest that CEOs are pursuing objectives other than, or in addition to, maximizing shareholder wealth and that they act to reduce the financial exposure associated with strategic investments.

Jan 1, 1997

By Jack Eloranta

This paper compares energy requirements for blasting, crushing and grinding. By tracking electrical consumption for various powder factors, a general trend has appeared. This study involves over 100 million tons of ore and powder factors ranging from .5 lbs/LT to .8 lbs/LT. Actual energy usage is compared to predicted energy based on the Bond equation.

Jan 1, 1997

By R. L. McNearny

A comparison study was conducted between an actual physical model and a numerical model based on the physical model of the block cave mining method. Results from the numerical analyses closely simulated the blocky behavior of the physical models, including bridging and interlocking of the simulated orebody during draw. The draw-down patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. An unexpected result from the numerical modeling was the development of a zone of downward deflection which preceded the development of the zone of material movement.

Jan 1, 1997

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

"AQUILA Mining Systems Ltd. is a Canadian company that designs and develops monitoring, control and navigation systems for the surface and underground mining industries. In 1992, AQUILA Mining Systems began the development of technology for monitoring, controlling and positioning mobile mining equipment. In 1993, AQUILA completed its first field test with GPS receivers onboard ablasthole drill, and thus demonstrated the viability and strategic relevance of this technology in surface mining. Since then, AQUILA has installed GPS-based technology on drills and shovels in several Canadian mines. This paper will review the development of these systems and discussthe benefits the mining industry could realise through their production implementation."

Jan 1, 1997

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By Dennis A. Beiter, William J. Francart

Barometric pressure changes have been an important consideration in the sealing of mines, especially in the case of mine fires. These changes are caused by storm fronts and regularly, on a daily basis, by atmospheric heating and cooling. In many cases, anticipation of these fluctuations in a mine sealing operation or recovery can be an important consideration when scheduling activities. The barometric pressure changes create pressure differentials across sealed areas, inducing airflows which may create explosive mixtures of mine gasses, cause intensification of fires, and create irrespirable atmospheres outby seals. These effects of barometric pressure fluctuations on mine fire sealing and recovery operations are discussed. Data available from the National Weather Service is also discussed as a tool for predicting barometric pressure changes.

Jan 1, 1997

By B. Lin, C. Tang, Z. Chen

Earthquakes, underground impact pressures and rock bursts all produce acoustic emissions. The rate of these emissions can be used to describe rock instability. In this study, it was found that acoustic-emission rates obtained by simulating a twin sample (rock-rock) model could be used to indicate the acoustic-emission-rate characteristics during rock instability. A computer simulation and two case studies support this conclusion.

Jan 1, 1997

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

By Appleyard B

The objective of this paper is to provide a brief to The AusIMM initiative which originated in 1996 and has developed from a concept proposed by Ric West, a Sydney consultant. The notes which follow are drawn primarily from a paper included in the Ironmaking Resources and Reserves Estimation Seminar volume presented by Vivienne Snowden, a member of the Towards 2000 Steering Committee and of the JORC committee.

Jan 1, 1997

By W. J. Errington

The Isasmelt process was developed at Mount Isa Mines Limited in Queensland, Australia in collaboration with CSIRO, the Australian Government research organisation. Originally developed for primary lead smelting, culminating in the construction of a 60,000 tonnes per annum lead smelter at Mount Isa, this technology now also provides a major part of the current 200,000 tonnes per annum copper smelting capacity at Mount Isa. A programme is now in place to expand copper production to 250,000 tonnes per annum. The technology has also been applied to secondary lead smelting at Britannia Refined Metals, a MIM subsidiary company, where a 30,000 tonnes per annum lead plant based on battery scrap feed has been operating since 1991. Mount Isa Mines Limited decided to license the technology in1988, and copper smelting plants utilising Isasmelt technology are now operated by Cyprus Miami Mining Corporation in the USA and by Sterlite Industries in India. In addition, the technology was adopted by AGIP for smelting copper/nickel concentrates in Australia. Union Miniere are currently constructing an Isasmelt furnace to smelt and convert copper-containing materials at their plant at Hoboken in Belgium. This paper discusses these developments and also some likely future developments which include the application of the technology for continuous copper and nickel converting and applications in the treatment of zinc-containing residues.

Jan 1, 1997

By OÆShea P. J, Dickson T. W

In April 1994 the Victorian Premier announced new State initiatives, collectively termed the Victorian Initiative for Minerals and Petroleum (VIMP), for exploration totalling $16.5 m over three years. The program, initially centred on the northwest of Victoria, the Eastern Highlands and the Otway Basin, is due for completion in June 1997 and has been designed to attract explorers to highly prospective but currently under-explored parts of the State. Major components of the program include acquisition of geophysical data (including airborne magnetics and radiometrics, gravity and seismic data), stratigraphic drilling, geological mapping and mineral resource data compilation. At the completion of the current program, 70 per cent of the State will have been covered by airborne magnetic and radiometric coverage at 400 m line spacing or better (Figure I) while 20 per cent of the State will have been covered by new geological mapping. The completion of database compilations for geochemistry, mine data and exploration licence summaries during the VIMP program is shown in Figure 2. The new airborne geophysical surveys have been flown partly under the VIMP program and partly by AGSO under the National Geoscience Mapping Accord (NGMA). Data from these surveys have been interpreted and incorporated into the geological mapping in order to enhance the quality of map products, especially in areas of Cainozoic cover. The first series 1:250 000 scale geological map coverage of Victoria was completed by the Geological Survey of Victoria (GSV) in 1977, and was based on compilation of historical geological mapping with minor field checking in most cases. The first metric 1:50 000 scale geology maps were also commenced in the 1970s, but were discontinued in the 1980s in favour of 1:100 000 scale map production. Driven by customer survey findings and with the benefit of detailed airborne geophysical data in the 1990s, the GSV reverted to 1:50 000 scale map production in 1995, with 1:10 000 scale maps made in areas of significant gold production. Geological reports still cover standard 1:100 000 scale map areas, but are now accompanied by four 1:50 000 scale maps. These new series 1:50 000 scale geological maps have been supported by comprehensive mine data and exploration licence summary databases in addition to the new geophysics, and benefit from the advances made in structural geological interpretation over the last decade. The new phase of geological mapping in Victoria, commenced under the NGMA in 1990 and accelerated under VIMP in 1994, has been focused in the central Victorian goldfields and eastern Highlands areas of the State (Figure 1). Results to-date have led to a number of major advances in the understanding of the eeoloeical evolution of Victoria.

Jan 1, 1997

By A. S. Polubinsky, V. P. Chernyak

A further development of the theory of heat- and mass transfer in the system “strata - mine opening" is necessary for an improvement of the existing technique of heat calculation of mines and other underground constructions. A generalized boundary problem of heat- and mass conduction in strata around an opening as a theoretical ground for that purpose and several particular situations, important from the point of view of an opening and surrounding strata heat state analysis, as well as results of numerical experiments executed for such analysis are presented.

Jan 1, 1997

By Brian Isherwood

TransCanada Pipelines, Calgary (TCPL) is one of North America's leading transporters of natural gas through its energy transmission business. TransCanada also operates significant complementary businesses in energy marketing and energy processing in North America and internationally. The main trunk pipeline crossing Canada comprises as many as six pipes, 30" to 48" diameter delivering up to 7.8 trillion cubic feet of natural gas per day. To maintain the maximum operating pressure of 1000 psi, it is necessary to provide compressor stations at 60 to 100 km spacing. One such station is located at Potter, in northern Ontario, some 80 km north of Timmins, referred to as Station 102. The station contains two compressor plants, 'A' and 'B' Each incorporates a gas turbine driven centrifugal compressor unit. 'A' Plant uses an aero-derived gas generator (jet engine) rated at 15 MW (19,000 HP).

Jan 1, 1997

By Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Jan 1, 1997