Search Documents

By Billy J. Thorne

The damage model in PRONTO simulates the dynamic fracture behavior of brittle rock. It is based on work started by Kipp and Grady, [lg] continued by Taylor, Chcn and Kuszmaul [I91 [20] and recently.modified by B. J. Thorne (first documented here). The essential feature of this model is the treatment of the dynamic fracture process in rock as a continuous accrual of damage in tension, where the damage mechanism is attributed to microcracking in the rock medium. The fundamental assumption of the damage model is that the material is permeated by an array of randomly distributed microcracks which grow and interact with one another under tensile loading.

Jan 1, 1989

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By G. P. Brahmaprakash, K. A. Natarajan, N. Jyothi, K. N. Sudha

Some important electrochemical aspects involved in the bioleaching of mixed sulfides have been discussed with reference to selective sphalerite dissolution from different binary mineral combinations. Combination potentials and galvanic currents were measured in different binary combinations of sphalerite with other minerals such as galena, chalcopyrite and pyrite in order to under- stand the electrochemical dissolution behaviour of sphalerite when coupled with other minerals. The effect of applied DC potential was also studied with reference to selective sphalerite dissolution from a binary mineral mixture. An application of a potential of -500 mV (vs SCE) was found to enhance bacterial growth as well as selective sphalerite dissolution. Factors influencing bioleaching of sphalerite under a negative applied potential are discussed.

Jan 1, 1989

By Beck RW, Booth GW

Differences in the gold contents of sub-sample duplicates, derived from a single bulk sample are a function of analytical and random error, inhomogeneity within the bulk and natural variations in the distribution of particluate gold. By minimising bulk sample inhomogeneity and determining analytical precision, the residual natural variation may be modelled statistically to give an estimate of Bold particle sizes.

Jan 1, 1989

By Jeffrey C. Reid

Computer processing and high resolution graphics display of geochemical data were used to quickly, accurately, and efficiently obtain impor¬tant decision-making information for tin (cassiterite) exploration, Seward Peninsula, Alaska (USA). Primary geochemical dispersion patterns were determined for tin-bearing intrusive granite phases of Late Cretaceous age with exploration bedrock lithogeochemistry at the Kougarok tin prospect. Expensive diamond drilling footage was required to reach exploration objectives. Recogni¬tion of element distribution and dispersion patterns was useful in subsurface interpretation and correla¬tion, and to aid location of other holes. Tin was its own best pathfinder. Arsenic, also a useful pathfinder element, forms a discrete halo peripheral to tin mineralization. The arsenic halo is expressed in hand specimens by asenopyrite and/or scorodite staining.

Jan 1, 1989

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989

By J. L. Jambor

Sulfide-rich tailings accumulated in a 4l-hectare impoundment at the Waite Amulet minesite near Noranda, Quebec, have undergone partial oxidation and destruction of the principal sulfides (pyrite and pyrrhotite) in the vadose zone. Mineralogical studies and whole-rock chemical analyses of 18 samples from 3 boreholes along a cross-section of the tailings pile indicate that the principal chemical manifestations of the alteration are a pronounced depletion in sulfide-sulfur, and an enrichment in total Fe as Fe203' Other elements such as Al, Mn, Mg, Ca, Na, and K in the solids show erratic or inconsistent variations, but a trend to Si enrichment in the oxidation zone is clear. The trend is interpreted to be a relative enrichment whereby the proportion of the stable silicate minerals has increased as a consequence of the consumption of pyrite and pyrrhotite in the oxide zone.

Jan 1, 1989

By A. E. Isaacson

Researchers at the Bureau of Mines, U.S. Department of the Interior, developed and tested equipment to measure corrosion rates on a commercial-scale mill. Bench-scale experiments were also designed for duplicating ore grinding conditions closely enough that realistic rate determinations can be made in laboratory tests. Rates measured in a laboratory system compared favorably with those measured in the field. Cast steel was found to have corrosion rates in a copper mill and laboratory test cell of 22 and 21 mpy, respectively. Corrosion was found to account for less than 5 pct of the total grinding media wear in the operations studied.

Jan 1, 1989

By D. A. Bruce

The use of small diameter cast-in-place bored piles is becoming increasingly popular in the United States. Such inserts are used as conventional load bearing piles, and are generally referred to as pin piles. The other major application is for the in situ reinforcement of soil slopes or excavations. The paper reviews the applications, construction, design and performance of inserts of each type.

Jan 1, 1989

By Kamal Wadhwa

Ever since the introduction of Liquid oxygen explosives in India in 1927, these explosives are being extensively used in the various mining industries such as coal, ironore, limestone, bauxite, magnesite etc. The earlier LOX compositions were based on cellulosic material of Weberlox series of French origin. They contained the basic ingredients of saw dust with an admixture of cork dust, some hydrocarbons and some metallic powders. However, there were some inherent defects in the soaking characteristics of these compositions, in as much as, absorption and retention of liquid oxygen in the cartridges were not properly regulated in the fine pores and in the inter-granular spaces inside the ingredients in a uniform manner.

Jan 1, 1989

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

By Henry Freiser

For the last several years, a systematic investigation of the equilibrium extraction behavior of selective tervalent lanthanides with representative chelating extractions of a variety of chelating agent families has been undertaken for the purpose of learning how to obtain chelating extractants of improved selectivity for separating individual lanthanide ions. The equilibrium extraction data (expressed as log Kex) for each reagent system are linearly related to the reciprocal ionic radius of the tervalent lanthanide ions. The role of adduct formation, steric hindrance, as well as the nature of the bonding atom in the chelate ring, represent some of the factors affecting selectivity arising out of our database of over 200 individual extraction systems, which will be discussed.

Jan 1, 1989

By A. F. Banks

"IntroductionThe typical potash processing plant recovers and/ or upgrades from 10% to 20% of its production through the recrystallization process. The feed to the recrystallization section consists of preconcentrated slurries of fine crystal size that cannot be raised to the required product grade by flotation and fine dusts also of low grade and too fine for compaction feed. It produces high grade white potash crystals that can be marketed as a high grade product or blended into the flotation products to raise their grade. In this chapter, a typical leaching (dissolving) and recrystallization operation will be discussed.The crystallization process makes use of the three phase system chemistry of NaCl, KCl, and H,O. The normal potash process operates on a temperature range of 75°F to 95 °F. A three phase slurry feed to the dissolving circuits will be within that range. The potash (KCl) is dissolved by heating the slurry in the presence of sufficient brine to a temperature of 190°F to 200°F. As the slurry is heated, the potash (KCI) dissolves and the salt (NaCI) precipitates. The potash rich brine is then clarified and the salt and other undissolved solids removed by thickening. Clarified brine becomes the crystallizer feed.The hot brine is cooled in evaporative cooling crystallizers. In cooling, the potash precipitates as a high grade white crystal. Crystallization is done in multiple effects to permit energy recovery and control of the process. In a four effect crystallizer the cooling is done by recycling mother liquor counter currently through the first two effect condensors and using brine pond brine for the cooling of the last two.The crystallizer product is removed from the last effect as a slurry at normal process temperature and is fed either to its own centrifuging and drying circuit or blended with the flotation product for centrifuging and drying."

Jan 1, 1989

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989

By Moxon N. T

The detonation pressure of ANFO can be significantly reduced by the addition of low density materials such as polystyrene, bagasse, swadust or perlite. Laboratory and field test results have shown that homogene- ous mixtures of these low density explosives can be produced in a bowl truck and loaded into a blasthole without segregation. The detonation pressure of the mixture can be altered to be more compatible with the material in which it is being used by varying the quantity of low density additive incorporated into the mixture. Field results have shown that these low density explosives can lead to significant cost savings without com- promising fragmentation or production.

Jan 1, 1989

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By P. A. Anderson

Innovative solution management is being used at Coeur-Rochester, Inc. to increase bullion production and decrease overall costs. New operating programs call for reduced solution application rates to the heap to increase pregnant stream values at a lower and less costly plant flowrate because silver and gold extractions are equal regardless of leach solution application rate. Solar heating is used in the summer months to increase the core temperature of the heap for use in the winter months thus increasing silver extraction rate. This paper outlines the programs now in effect and the savings incurred because of them.

Jan 1, 1989

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989