Search Documents

By David M. Sullivan

Jim Walter Resources, Inc., (JWR) a division of Jim Walter Corporation, has 5 underground coal mines in Central Alabama varying in depths from 400-2500 feet. Gas Chromatography plays a vital role in safety and production at each mine. Chromatographic data is used to monitor working areas for safety and proper ventilation and to control the quality of extracted methane for sales purposes. Instruments have a1 so been employed during mine rescue operations. JWR's first Gas Chromatograph (GC) was installed in April 1984 to monitor gob gas taken from longwall gob areas and sold based upon BTU value. The GC allows maximum extraction rate of the gas within the quality guidelines. By late 1985, another system was purchased and both units were upgraded to perform an analysis of indicator gases which may appear during mine emergencies. Each unit has the ability to detect and measure the following gases at almost any level ; Oxygen (021, Nitrogen (N2), Methane (CH4), Carbon Dioxide (C02), Hydrogen (HZ), Carbon Monoxide (CO) , Ethylene (C2H4), Ethane (C2H61, Acetylene (C2H2) and a composite of hydrocarbon threes and above (C3+). The analytical run is accomplished in less than ten minutes and is completely automated. This report will introduce Gas Chromatography as applied by Jim Walter Resources for the analysis of underground mine air.

Jan 1, 1987

By Woodcock J. T, Millett R. N

It was shown that manganese dioxide could be used as an oxidant in acid thiourea leaching of a gold ore. Manganese dioxide could generate high redox potentials and was as effective as hydrogen peroxide in the leaching process. Results obtained under closely controlled leaching conditions confirmed that high redox potentials enabled faster dissolution of gold to be obtained but led to extremely high reagent consumptions (thiourea, acid, and manganese dioxide). Additions of sodium sulphite solution in an attempt to lower thiourea consumption by reducing formamidine disulphide back to thiourea were only marginally successful. Although thio- urea consumption was slightly decreased, the consumption of acid and manganese dioxide was substantially increased and there was no net benefit in using sulphite. Tests in which a single addition of mangan- ese dioxide was made before addition of thiourea minimized overall reagent consumption and gave only a slightly lower dissolution rate of gold. This is a promising technique for further Investigation.

Jan 1, 1987

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

The classic description of Project Finance as "the reliance by lenders on the cashflow of a project, supported by the assets of the project with no recourse to the project sponsor's corporate balance sheet" has, like most other terms in the finance industry, evolved through recent usage. The area now under most scrutiny is the sharing of risks between parties either most able to take them or prepared to accept payment for them. Creativity in, and flexibility of financing structures have enabled project lending to continue under a dramatically different economic outlook. The diminishing competitiveness of the Australian producers in a global market place of uncertain commodity prices has discouraged the advancement of many large scale resource projects. The majority of new project financings has been designed to assist the relatively small company promote and develop its first projects. New trends- are emerging in four areas: sources of capital; borrowing structure; financing instruments (securitisation); and risk underpinning. As project financing becomes more widely used, the range of interested financiers grows. New initiatives contribute to its development and evolution with a view to increase effectiveness to the sponsor of any new venture.

Jan 1, 1987

By S S. Kahlon

India is a large and growth market for explosives and accessories, which has dramatically changed from complete import dependence to self sufficiency, and now has an exportable surplus. The largest single user is coal mining which is continuing to show a healthy growth with opencast mining becoming increasingly dominant. The explosives industry has kept pace with mining and today all the well renowned explosives technologies of the world are available in the country. While slurry explosives are popular in large diameter, NG based explosives continue to be preferrred in small diameter usage. Emulsion explosives have had a good market response. ANFO usage is limited due to local reasons. As the mine size is increasing, the demand for bulk-on-site explosives is growing. Prices of explosives and accessories are cheap compared to international levels. The user industry is mainly Government owned mines whose profitability is not satisfactory. Explosives industry is over licensed in terms of manufacturing capacity, which is likely to put pressure on the viability of some of the explosives manufacturing units. Scope exists for optimization of blasting parameters through the use of computerized blasting models. The explosives industry is faced with new challenges and opportunities.

Jan 1, 1987

By A. A. Schweizer

Buckhorn ore is hydrous, argillized basaltic andesite, and is at least 60% clay composed of kaolinite and subordinate montmorillonite. Moisture content runs from 10% to 25%. The original crushing plant was a typical compression type, employing a jaw crusher, and two cone crushers. The system was plagued with constant plugging and unable to meet production plans. The three compression crushers were replaced with a Stamler Feeder Breaker followed by a Hazemag Impactor. Production plans are now exceeded. Agglomeration has progressed from an agglomeration drum to cascading conveyors, to introduction of the lime and cement into the primary crusher.

Jan 1, 1987

By Mark Springett

Microcomputers have rapidly evolved to the level at which they can perform almost all of the computational tasks required for exploration, evaluation and exploitation of mineral deposits. The present capabilities of microcomputers are reviewed by examining their use on typical projects from the initial capture of exploration data to the subsequent technical and financial evaluation by microcomputer. Emphasis is placed on the need for compatible software and on the importance of a consistent hardware acquisition policy.

Jan 1, 1987

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987

By Gabriel de Almeida

INTRODUCTION The widespread use of desktop computers by an ever increasing number of people, both for personal and for business and government uses, has brought public attention to surprising stories about computer abuse. Before the advent of microcomputers in the information processing environment, hundreds of amazing misdeeds involving large computers had already been reported, most of them perpetrated by highly skilled professionals. The undreamed enlarging of microcomputer potential has steadily posed a major threat to complex mainframe computing systems, as joyful teenagers become familiar with the habit of hacking around someone else's large processing system, by means of makeshift phone communication networks, based on their intended homework for personal computers -- for the sheer fun of it. Now, the never ending capacity and speed improvement of commercially available micros has given rise to a brand new concern for society: the hazards of processing sensitive information in the powerful, but still unsafe microcomputer itself, whether or not linked to other micros or mainframe networks. This paper deals with some aspects of the problems and presents some practical hints as to enhance protection and minimize risks to sensitive and secretive information when processed on microcomputers. The physical considerations of computer security and pertinent safety precautions will not be discussed, because while essentially relevant to information protection, recommendations are well defined by processing resources suppliers and their importance is more widely recognized by users in general. Definitions and Classifications. The following definitions and classifications will be considered in this report: Information Assets: Any knowledge or information processing, storing or conveying device displayed in one's environment. It consists of two main categories: INFORMATION RESOURCES: End user's application data wherever recorded. PROCESSING RESOURCES: EDP skilled user's hardware, software, peripherals, magnetic media, communication devices, auxiliary equipment, supplies and related operational procedures. Information Protection: In a broad sense this is the set of necessary procedures to assure to the legitimate user the effective control of the operation and allow modifications of information assets, so that their physical or cognitive integrity be preserved or any unexpected loss minimized inspite of accidental occurrences or intentional actions. Classification Processes: Commonly two classification processes are used to define key terms in information protection: SENSITIVE CLASSIFICATION: Pre-defined standards for assessing the vulnerability to losses due to lack of proper processing continuity if information is destroyed, disclosed, secluded, or misused. SECRECY CLASSIFICATION: A spectrum of degrees as to the expectancy of holding exclusiveness of unique information whose destruction, disclosure, seclusion or misuse will cause a negative impact on the legitimate holder environment. Sensitive Information: Any knowledge whose destruction. disclosure. seclusion or misuse - - - implies losses to its legitimate holder. It may be classified as: VITAL INFORMATION: An essential knowledge whose lack of proper availability implies total loss or termination of p

Jan 1, 1987

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By William D. Mayercheck, August J. Kwitowski, John R. Bartels

This report discusses the Bureau of Mines' efforts to develop partial protective structures for operators of low-coal shuttle cars. In coal seams 48 in high or less, full-coverage canopies are generally difficult or may be impossible to implement on high-speed face equipment due to the restrictions they impose on the operator's vision and comfort. Lim- ited coverage is one alternative that provides an acceptable level of operator protection in thin-seam applications where conventional full- coverage canopies cannot be used. Three possible limited-coverage de- sign scenarios (roll bars, sliding canopies, and flip-top canopies) were designed, fabricated, and evaluated for low-coal shuttle cars. All three designs were determined to be feasible and desirable for low-coal shuttle car application.

Jan 1, 1987

LESLIE BRADFORD GOLDEN JUBILEE ORATION "Not only a metallurgist but a scientist of the highest order" Leslie Bradford and the Australian Metallurgical Industry

Jan 1, 1987

By Seedsman RW, Duncan Fama ME

Mine design procedures will be revolu- tionised by technological developments in computers, software, database construction and management, and numerical modelling programs. Developments in geotechnical databases will be required which utilize geological and geomechanical tests to supply appropriate input for numerical models. Techniques utilizing sedimentological and structural modelling are described. The capacity of current numerical models in mine design is outlined and a program for developing a fully integrated mine design package proposed.

Jan 1, 1987

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By Abdalla MH

The deformation resulting from the presence of a tunnel may signifcantly affected, nearby structures and need to be considered during design of both tunnel and structure. The aim of this paper is to study the effect of different factors which may affect the interaction between the tunnel and the str- ucture. These include; the depth of both tunnel and foundation level of the structure ( z and t ), distance between C.L. of tunnel and loads, breadth of the loaded area, Diameter of tunnel and lining of the tunnel. The problem is studied as a two dimensional plane strain model by the boundary element technique. The results of this study indicated that the presence of a cavity/tunnel increases, in general, the vertical displacement on the ground surface and at the foundation level as well as the horizontal and vertical stresses in the cavity/tunnel level. The effect of eccentricity is increasing as e/D decreasing. For pile foundation there is a quite different- influence of the presence of cavity/tunnel in both cases of friction pile and end bearing pile type of foundation.

Jan 1, 1987

By E. C. T. Chao

Micro-optical and synchrotron radiation-induced X-ray fluorescence (SXRF) techniques have been used to study unoxidized and oxidized samples of Carlintype sedimentar,y rock-hosted disseminated gold ore. In these samples, Where much of the gold is submicroscopic, the SXRF technique, which has a spatial resolution of about 20 ~m and a minimum detection limit (MDL) in the ppm range, is an ideal and necessary tool for precisely locating gold-rich areas in a sample. Gold-rich areas pinpointed by SXRF were later studied in detail by micro-optical methods, principally optical microscopy and scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). In two unoxidized and one oxidized ore samples, SXRF analyses have shown gold to be present predominantly in discrete clay-rich and silicified areas. Gold was not detected by SXRF in association with pyrite or carbonaceous materials. SEM-EDX examination of the gold-bearing areas in the unoxidized samples succeeded in identifying only two free gold particles, 0.2 and 0.5 ~m in size. In the oxidized sample, gold particles appear to be larger (but still submicroscopic) in average size and more evident in micro-optical examination after SXRF location of goldbearing areas. The findings of these studies may help to improve the efficiency of processing and recovery of gold from unoxidized ores.

Jan 1, 1987

By Betty L. Gibbs

A clear and accurate knowledge of the status of ventilation in an underground mine is essential to continuing safe operation. In a small mine with a few working faces, the problem is simple and can easily be solved by choosing the appropriate fan. In larger, more complex mines the problem of supplying the working faces with fresh air is a problem beyond the scope of 'finger in the wind' analysis. In today's climate of stiffer government regulation and mining company concern for the safety of workers, computer programs which analyze ventilation networks are helping mining companies meet the standards. The development of computer programs for ventilation network analysis is summarized. Early programs were developed at universities or government agencies and required large expensive computers. As computers have become smaller and less expensive, the development or revision of programs for micro computers has become more available. Prices have lowered to the point of affordability even for medium and small companies. A list of ventilation network analysis programs is provided along with a summary of capabilities, costs, and hardware requirements for each program.

Jan 1, 1987

By Walshe JL, Solomon M

The Emperor vein system lies on the eastern margin of the Tavua volcanic structure. This is of Miocene age and occurs in basalts(the Mba Volcanics) probably underlain at about 2 km by calcite-rich sediments (the Vatukoro Formation). The lodes are generally flatmakes, or steep fault fillings, or complex shatter zones, and consist of quartz and altered wall rock. In areas of open cavities it is possible to establish a paragenesis which involves five quartz stages and two ore mineral stages. The first ore stage contains calaverite, krennerite, sylvanite and native tellurium, the second petzite, hessite and native gold. The quartz stages are thought to have formed slowly (102 years) from boiling solutions of low salinity at temperatures varying with time from about 250¦C to 190¦C. The system was sealed, the temperature gradient near vertical and the mass flux small. The ore mineral stages probably formed relatively rapidly (101years) from boiling solutions at 250¦ to 200¦C when the system was mainly open. Gold deposition was probably largely a result of fall in aH2S due to boiling, the calculated solution concentration falling from a maximum of about 8 ppb at 250¦C to about 8.10-3ppb at 200¦C. Boiling is also probably responsible for an increase in a02 (by loss of H2) and fall in aTe2 (by loss of H2Te). The fluids are thought to have had a large component of meteoric water and to have been heated by plutons in the core of the volcanic structure. Stable isotope data indicate that they derived their carbon from the underlying Vatukoro Formation and their sulphur from sediments. Circulation may have been confined to the outside of the volcanic structure because of the relatively low permeability of the flows, pyroclastics and dykes within it.

Jan 1, 1987

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987

Palaeomagnetic work on the red beds of the Hervey Group from central N.S.W., and on the Mount Eclipse Sandstone from the Ngalia Basin, Central Australia, reveals a pre-deformational magnetization from the Hervey Group, which indicates a semi-equatorial palaeolatitude during the latest Devonian or earliest Carboniferous and a syn-deformational magnetization from the Mount Eclipse Sandstone which places Australia at a palaeolatitude of about 70¦ ¦ 20¦S during the early Late Carboniferous. By comparison with the existing data from Australia, the new results indicate that: (1) Australia (and thus eastern Gondwanaland) underwent a rapid southward movement of about 60¦ during the late Early and early Late Carboniferous, (2) the Lachlan Fold Belt has been part of cratonic Australia since at least latest Devonian or earliest Carboniferous, and (3) the New England region and cratonic Australia were at a similar palaeolatitude during earliest Carboniferous, but they may have undergone the rapid southward movement separately.

Jan 1, 1987