Search Documents

By S. K. Nandy, K. F. Unrug

The behavior of the immediate shaly roof within a drift mine in eastern Kentucky, operating in the Coalburg seam, was monitored with roof bolt dynamometers. The dynamometers used were capable of providing readings up to a maximum load of 66.72 kN (15,000 lbs), + 0.022 kN (5 lbs). To observe the influence of moisture on the rate and extent of roof deterioration, 57dynamometers were installed on roof bolts anchored in intake and neutral airways. Monitoring was conducted during the period January 1985 through January 1986, in order to cover a full cycle of dry and wet mine conditions associated with seasonal changes. Analysis of the data showed a trend of roof deterioration induced by condensation and eventual penetration of moisture within the immediate roof bedding planes, leading to rapid disintegration of the mine roof.

Jan 1, 1987

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

By Henry P. Cole, Andrzej M. Wala

Engineers and psychologists at the University of Kentucky have developed simulation exercises that teach and test proficiency of mining technical personnel for coping with planned and accidental connections between separate air courses in underground mines. The exercises are based upon investigations of actual mine disasters. The exercises are judged as valuable and interesting training materials by experienced mining personnel. Although these specialists generally perform well on the exercises, potentially fatal errors are not uncommon. The use of such realistic exercises may better prepare miners for preventing and coping with underground mine ventilation emergencies.

Jan 1, 1987

By J. F. T. Agapito, C. E. Brechtel, C. J. Gilbert, T. R. Kelly, R. C. Karlson

A multi-lift benching cut-and-fill mining method was adopted at Asamera Minerals (U. S.), Inc.'s Cannon Mine to balance the goals of high productivity and near 100 percent recovery with the need to minimize subsidence. High strength backfill was required to provide effective long-term overburden support and safe working conditions during the pillar recovery operations. Operational designs were evaluated using numerical modeling to predict global mine stability and backfill strength requirements. These models incorporated sequential mining of primary stopes, backfilling of primary stopes and recovery of pillars, and have been transferred to the mine operations group for use in evaluating different production sequences. The modeling has provided a better understanding of the structural response of the mine to excavation of the primary stopes and removal of the pillars. Predictions about the transfer of overburden weight to the abutments, pillars and cemented fill pillars have provided a criterion to evaluate mining plans and production sequence. Comparison of these predictions with actual mine structural performance has developed confidence in the design of the mining method and in the geomechanical design methods being employed. Primary mining of the B-North zone is nearly complete, and the stopes have been generally stable, as projected in the original design. Some exceptions have occurred where locally stope pillars have failed due to the presence of adversely oriented sheared beds. Recovery of the pillars between the

Jan 1, 1987

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION The Soudan 2 Cavern was completed in 1986 as a physics research laboratory located 713 m below ground in northern Minnesota. A paper in the 1985 RETC proceedings presented the background and planned usage for the cavern, site investigation and rock conditions, contract documents, and a bid summary. This is a follow-up paper describing construction of the cavern. The Soudan 2 excavation, 71.8 m long by 13.9 m wide by 11.6 m high, was excavated by drill and blast methods and mucked by crawler tractor and mine hoist. The excavation sequence consisted of twin top-heading pilot tunnels followed by removal of the top heading pillar and finally the bench. Various blasting designs were used to achieve adequate breakage and acceptable levels of blast damage control at the cavern perimeter. The geologic conditions exposed in the cavern, and the support needs of the rock encountered, are compared to the conditions interpreted from the site investigation. The influence of specific geologic features on cavern performance will be described. Initial support and final lining consisted of full length grouted rockbolts and reinforced and plain shotcrete. Trials were conducted with steel-fiber reinforced shotcrete and microsilica additives. The performance of the rock and support systems was tracked with single point extensometers, convergence measurements

Jan 1, 1987

By K. F. Lane

Mine planning is a complex function and also a vital one. The quality of the planning has a profound effect on the efficiency and the economics of every mining operation. It is therefore important that the function should not be reliant upon only a few techniques but should have command of an orchestra of them. Then the most appropriate can be selected for each application or, if it is advantageous, a group can be employed in concert. This paper introduces peripheral algebra as a set of techniques which should be included in the mine planning orchestra. Its objective is primarily to stimulate more development not only of these techniques but also others of a similar kind which will increase the effectiveness of mine planning.

Jan 1, 1987

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By S. K. Mukherjee, M. M. Singh, N. I. Jayaramn

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years, there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper recommends guidelines for water spray systems to control dust in underground mining operations. These guidelines suggest type, number, location, and orientation of nozzles; desirable operating water pressure; and associated filtration system.

Jan 1, 1987

By John K. Hollmann

The use of the direct method of determining coal methane content has grown in the last decade from a research technique into a practical coal exploration tool. However, the literature available on the subject is somewhat lacking in site-specific guidance and observations on the conduct of the method and the use of the resulting data. This study discusses some practical lessons learned in conducting a large scale direct measurement project at an operating mine, describes the initia1 interpretations and uses of data from the project, and presents observations from subsequent mine operations into the success and limitations of using direct measurement data in mine planning. The site studied is in central Pennsylvania on the Appalachian Plateau and includes coal seams in the Allegheny series.

Jan 1, 1987

A new least-squares method for inversion of d.c. resistivity soundings from horizontally layered earth is proposed. Powers are used as measured data. Apparent resistivity is generalized and apparent parameters curves are defined. Estimates for parameter errors are often possible even when data errors are unknown or large. Acceptance or rejection of a model is made an easier decision. Total computational effort is often reduced when compared to global least-squares methods, because although several optimizations are needed, few data points are involved in each, and initial guesses are requested only once and not all at the same time. Correlations between parameters may be used to improve solutions. Precise indications for extra needed data points can be conveyed. A test example is worked out and a field sounding, taken by Rijo (1973, personal communication) in an alluvium-filled river valley in north-eastern Brazil, is studied.

Jan 1, 1987

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

By A. P. L. Kotzé

Modelling and scheduling for Grootegeluk coal mine, situated in the north- western Transvaal, is by means of a series of modular systems. Modelling of the multilayered body, which is part of the Waterberg coalfield, was based on a detailed study of the behaviour of coal and waste qualities and the sub- sequent use of standard geostatistical techniques. A notable improvement on previous methods was attained. Scheduling procedures and systems were developed to model a multibench pit producing coal for several metallurgical plants as well as a power-station. Scheduling was done by producing a series of longitudinal cuts, the cuts being subdivided into increments. By allocating cuts to certain periods, the resulting calculated product tonnages were com- pared with production targets, and by iteration a final scheduling sequence was determined.

Jan 1, 1987

By Steven R. Wardwell, Gerald G. Stokes

INTRODUCTION A compaction grouting program to control ground loss, and to minimize surface settlement, was developed for the West Tunnel of the Phoenix Storm Drain Tunnels. The West Tunnel was 4,200 m long, 7.56 m in excavated diameter, and was excavated with shallow cover through the central Phoenix business district. The tunnel could not have been successfully excavated without the compaction grouting program. HISTORY After heated political debate over a ten year period, the Arizona Department of Transportation (ADOT) was granted approval to build the Papago Freeway, an extension of Interstate 10, through central Phoenix. To comply with environmental constraints, a portion of the Freeway was depressed, requiring an excavation 10 meters in depth, thus intersecting surface run-off from the northern section of Phoenix. This required that ADOT and Project Design Consultant, Howard, Needles, Tammen & Bergendoff (HNTB) design a drain system to collect run-off and transport it approximately 4 kilometers to the Salt River through the City of Phoenix. Tunnels were chosen for the main discharge conduits because depth and location of the system made cut and cover construction impractical. A contract for construction of the tunnels was awarded to Shank-Artukovich-Ohbayashi (S-A-O) on May 24, 1984.

Jan 1, 1987

By Scaife PH, Cripps Clark J, Cameron DB

Tuyere coke samples have been taken through the tuyere openings of B.H.P. International Blast Furnaces since 1978 with Whyalla No. 2 Blast Furnace taking samples on a regular basis since 1982. The degradation of coke during it's passage through the Blast Furnace can be measured and the relationships between these data, feed coke data and blast furnace operating data demonstrated. Tuyere coke sampling has been useful in revealing misleading external coke testing results and is still the method to monitor directly the performance of coke within the Blast Furnace.

Jan 1, 1987

Precious metal mineralization at the North Arm goldfield in SE Queensland occurs in the Triassic North Arm Volcanics, a sequence of andesite to rhyolite, pyroclastic and epi- clastic rocks deposited in a continental envir- onment. This unit displays a well-defined fracture system on Landsat imagery, including several arcuate structures which may represent former calderas. Two of the latter are associ- ated with zones of hydrothermal alteration, breccias and anomalous precious and volatile metal values. At the North Arm prospect, alter- ation is zoned from outer propylitic into exten- sive sericitic, although K-feldspar alteration is prevalent in the rhyolite. A zone of advanced argillic alteration is also present at Mt. Ninderry, SSE of North Arm. Alteration involves depletion of Na, Ca and Sr, and vari- able enrichment of S, As, Au, Ag, Hg and Mo. K and Rb are strongly enriched in K-feldspar altered zones. Precious metal mineralization occurs in veins, stockworks and hydrothermal breccia zones, and pervasive low grade Au-Ag dispersion is found throughout the sericitic and K-feldspar altered rocks. Veins and brec- cia interstices contain abundant quartz (common- ly banded), minor pyrite, calcite and sericite, with traces of silver grading to electrum, frei- bergite, naumannite, allargentum, marcasite, chalcopyrite and sphalerite. Mineralogical and geochemical characteristics are consistent with that found at volcanic-hosted epithermal precious metal deposits, particularly with the low-sulphur/adularia-sericite type.

Jan 1, 1987

By Chris C. Sundberg, Ronald E. Heuer, Stanley L. Paul, Peter M. Douglass

Use of prestressed concrete cylinder pipe (PCCP) for pressure tunnel liners is gaining popularity with contractors, engineers, and owners. This paper presents loading considerations and a beam-spring computer model approach to tunnel liner analysis, together with ultimate strength (US) and service load (SL) procedures for liner design. The US procedure is best suited to check for adequate liner strength under extreme loading conditions. The SL procedure, based on conventional pipeline design practice, is considered more appropriate when addressing crack control and serviceability under normal working load conditions. Other design and construction considerations are discussed and a design example is presented.

Jan 1, 1987

By J. M. Barker

Formation of commodity agreements depends mainly on the economic instability and associated mitigation measures inherent in the economic conflict between more developed and less developed nations. Five types of possible agreements exist: futures market, buffer stock, restrictive agreement, multilateral contract, and compensatory finance. Lack of market separation between sulfur consumers and producers coupled with large world production and highly concentrated export production in theory suggest a restrictive agreement as most likely. In practice, stockpiling of sulfur, an informal buffer stock, as done in Canada and perhaps the Middle East, has been the main sulfur price-supporting mechanism in the past two decades. No commodity agreements involving sulfur now exist except for multilateral contracts. Sulfur agreements apparently have existed rarely, if at all, in the past. Law (1975) refers to sulfur as one of a group of commodities where "there have been additional control efforts of various types." Clearly, sulfur was a candidate, at least conceptually in the past, for some form of commodity agreement. The following discussion centers on the world sulfur market from 1976 to 1985 in this context.

Jan 1, 1987

By V. R. Manukonda

Selective flocculation of iron ores is extremely sensitive to the type and the amount of soluble salts in pulp solutions. Chemical precipitation of alkaline earth ions combined with ultrasonic treatment deactivates their adverse effects without using any environmentally ill-defined reagents. The manner in which ultrasonic treatment affects starch adsorption on hematite, dissolution of quartz, and selective flocculation process was investigated. Selective flocculation tests were conducted in the presence of up to 400 ppm calcium ion on a quartz-hematite mixture by precipitation as calcium carbonate, and the role that silicate ion generated by ultrasonic treatment plays in achieving the selectivity of separation is discussed.

Jan 1, 1987

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987