Search Documents

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By Edward M. Dowey

This paper presents the excavation of the Roosevelt Island Valve Chamber, the final of three chambers in Stage One of New York City's Third Water Tunnel. The valve chamber and passageways 13 379.7 cu m (17 500 cu yd) are drilled and blasted. The rock is stabilized by grouted rock anchors. The 6.1 m (20 ft) diameter shaft is drilled, blasted, rock bolted and wire meshed for a depth of 70.7 m (232 ft). Then shaft excavation proceeds with immediate concrete lining for another 120.7 m (396 ft). Two 6.1m (20 ft) diameter manifolds are excavated using heading and bench. The raise drilling of eight 3.7 m (12 ft) diameter laterals occurs during lower shaft sinking.

Jan 1, 1987

By J. Mitchell Linne

In 1986 at the request of Bureau of Land Management, the U.S. Bureau of Mines studied 23,225 acres of the 27,980-acre Jordan Craters Wilderness Study Area (OR-003-128) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 20 miles northwest from Jordan Valley. No mining activity has been recorded within the study area, and no metallic or industrial mineral resources were identified. Small isolated occurrences of decorative quality stone were identified. However, none of these occurrences constitute a resource. Although the study area is underlain by relatively young volcanic rocks, the area has no known geothermal energy resource.

Jan 1, 1987

By Michael D. Dunn

The Bureau of Mines evaluated a quartz schist formation within the Blue Joint Wilderness Study Area which was identified as having a "high potential" for copper-silver-cobalt-barium resources. Stratiform and remobilized copper occurs near, and bedded barite within, the study area. In addition, the black to gray Proterozoic quartz schist may correlate with the Yellowjacket Formation which contains cobalt-copper-gold-silver deposits at Blackbird, ID, about 30 miles to the south. Eighty soil and 43 rock samples collected across the quartz schist formation were analyzed for gold, silver, copper, cobalt, and barium. During the reconnaissance and sampling, particular attention was given to looking for malachite (copper carbonate) and erythrite (cobalt arsenate, also known as "cobalt bloom"). The sample analyses and geology in this localized area do not provide enough evidence to support the "high potential" designation for copper-silver-cobalt resources. Barium potential still appears high, however.

Jan 1, 1987

By Gordon I. McPhail, John D. Nelson

Tailings management represents a major portion of the cost associated with extraction of gold. For each gram of gold extracted, 150 to 200 kg of waste material is produced. Because of environmental concerns and unwillingness of society to accept environmental damage caused by poor waste management practices it has become essential to follow responsible and safe practices in tailings management. This paper presents general aspects of tailings management and discusses different techniques utilized. Characteristics of tailings and the effects that these have on stability and environmental aspects are discussed. The paper also discusses the effect of mine back-filling practices on the surface disposal of the remaining tailings fraction.

Jan 1, 1987

By Siegmund Babendererde

Introduction Lyon, with 1.1 million inhabitants, is the third largest city in France after Paris and Marseille. It is a lively industrial centre. Lyon lies at the intersection of many transport routes and at the fluence of Rhone and Saone. Like all large cities, Lyon is attempting to alleviate inner city traffic problems by constructing a metro. Metro construction in Lyon began with tunnels built by cut and cover methods along the streets. Deep diaphram walls, which were back anchored and toed into imperveous strata, formed the excavation walls. It is a very economic and simple method. However during the construction period, it has the disavantage of strangling urban life for several years. It is therefore increasingly being replaced by subsurface tunnelling methods. As it was decided to build the metro tunnel between the Guillotiere and St. Jean stations, and thus cross under the Rhone and Saone, the client, Semaly, put the contract out for a competitive tender in which the general parameters were defined. Line, level and construction method were left to the contractor. There was an extensive examination of the tenders, during which reference projects from competitors in Japan were visited, as well as in Germany. Finally the consortium of Dragages, Campenon Bernard, Colas and Hochtief was awarded the contract to drive this tunnel section with an hydro-shield and an extruded steel fibre concrete lining, a Hochtief design.

Jan 1, 1987

By Robert H. Peters

This Bureau of Mines report describes several significant problems associated with absenteeism among underground coal miners. The vast empirical literature on employee absenteeism is reviewed, and a conceptual model of the factors that cause absenteeism among miners is presented. Portions of this model were empirically tested by performing correlational and multiple regression analyses on data collected from a group of 64 underground coal miners. The results of these tests are presented and discussed.

Jan 1, 1987

By Moeller T

The Bottle Creek mine, when opened next month, will consist of three open cuts, Emu, VB and Boags, feeding ore to a central mill. The open cuts cover a strike length of 4.5 kilometres which forms part of a linear structure, which can be traced geochemically for 26.0 kilometres. With the exception of a few small gossanous outcrops at Emu, the deposits are completely covered with insitu laterite and alluvial overburden. Since its discovery in 1984, the deposit has been subjected to three major reverse circulation (RC) drilling programmes which have successively closed up the drill spacing on the main mineralized zone to 25m horizontally and less than 25m vertically. All resource calculations have been based primarily on samples of RC drill cuttings from these programmes. Ore reserve calculations have been completed after each drilling phase. They began with a simple polygonal technique, progressed through two sectional half-distance calculations and are now being completed with a 3-D geostatistical technique. Because of the style of mineralization, Norgold personnel paid particular attention to assessing the variability of the mineralization by using repeat samples, repeat analysis and diamond drill vs RC comparisons. In addition, close attention has been paid to obtaining an accurate estimate of the global SG of the ore bodies. Particular care has been taken to obtain complete drill intersections of the orebody and to maximize wet sample recoveries. Extensive re-sampling and re-analysis of samples has confirmed that Bottle Creek is unusual for an oxidized gold deposit in that all the gold appears to be very fine grained, and evenly distributed within the mineralized zone.

Jan 1, 1987

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By Joan Weinberg

The economy continued to expand during the third quarter, as real GNP rose at a seasonally adjusted annual rate of 3.8%, up from 2.5% in the second quarter (table 1). Continued job gains (see below), higher incomes, and an increase in installment debt, resulted in a nearly 20% increase in consumer spending on durable goods. Consumer expenditure on nondurables fell slightly, while spending on services continued at a moderate pace. Nonresidential fixed investment climbed nearly 24%, as producers purchased more durable equipment. Residential fixed investment was adversely affected by rising interest rates, which slowed new home construction from January to August, 1987 to a rate 11.2% below a comparable period in 1986. Net exports of goods and services deteriorated slightly, after three consecutive quarters of improvement. The volume of net exports has risen 15% for the year, contributing to economic and employment growth, but large price increases on imports have slowed the improvement in the nominal trade balance. Although U.S. goods have declined in price relative to foreign goods because of the devaluation of the dollar, faster growth in exports is hampered by austerity programs in developing countries, and emphasis in Germany and Japan on curtailing inflation and fiscal deficits.

Jan 1, 1987

Studies of the minor element content of sphalerite and pyrite have generally been concerned with individual deposits or localised groups of deposits. However, a small number of more regional investigations have been reported (e.g. Davidson, 1962; Groves and Loftus-Hills, 1968; Loftus-Hills and Solomon, 1967; Price, 1972; Bralia et al., 1979) which have used the minor element abundances to evaluate the petrogenesis and geological affinities of diverse ore types and to fingerprint metallogenic provinces (e.g. Ivanov, 1964). While generally held to be valid, some doubts have nevertheless been cast on the reliability of minor element abundances in petrogenetic deliberations (e.g. Mercer, This paper reports on the distribution of he. Cpl and Mn in sphalerite, and Co, Ni and Mn in pyrite, from sulphide mineral occurrences within the "eugeosynclinal" prism comprising the New England Region of north-eastern New South Wales and south- eastern Queensland (Fig. 1). The occurrences examined are representative of two well-defined styles of mineralisation (Stanton et al., 1974) within which clear patterns of ore-rock distribution give rise to specific metal associations (Herbert. 1977).

Jan 1, 1987

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

The metallogenic belts of the Central Andes (iron, porphyry copper, polymetallic and tin) are genetically related to an eastward migrating magmatic arc. The polymetallic belt of the Bolivian Altiplano formed during Miocene arc broadening and lies in a critical position for understanding the genesis of this zonation. It is penecontemporaneous with parts of the copper and tin belts, and shares many characteristics with them. The differences between the belts result from contrasting volcanic and feeder stock geometry, depth of erosion and country rocks, and are not due to variations in magma chemistry, age or Benioff Zone depth. Polymetallic mineralisation in the Altiplano is epithermal in style and mostly related to flow-dome volcanism. The intermontane basinal setting precludes deep erosion to expose the epizonal feeder stocks and predicted porphyry copper mineralisation. In contrast, erosion of the less abundant stratovolcanoes of the Altiplano-Puna and Pampean Massif may expose contemporaneous Miocene porphyry copper mineralisation in subvolcanic stocks. The tin belt is coincident with the Paleozoic fold belt of the Eastern Cordillera. The occurrence of minor tin in Altiplano epithermal deposits hosted by Paleozoic sediments, and the persistence of tin mineralisation in the tin belt over 350Ma, suggests that Paleozoic sediments are the source of the tin.

Jan 1, 1987

By Peri Mehling, Allister Brown

Environmental regulations concerning the processing of gold ores and the treatment and disposal of spent process solutions range from rigid standards in some locations to site specific options in several other jurisdictions. This paper examines the regulations and policies in two North American jurisdictions. Emphasis will be placed on the mill process and waste stream treatment and disposal, and implications for environmental impacts. Case examples of mine licence requirements will be discussed, with brief descriptions of individual treatment and disposal systems. Policies and environ- mental regulations within each jurisdiction will be examined in terms of potential environmental protection.

Jan 1, 1987

By K. T. Cunningham

The Oakfield, New York Hine of the United States Gypsum Company is a shallow, room and pillar mine developed in the Camillus Formation of Silurian Age on the up-dip edge of the northern Appalachian Basin. The gypsum comes to subcrop beneath a variety of glacial materials and is subject to solution activity by groundwater. A geologic environment unfavorable to mining activity is thus created. Since 1978 seismic studies have been used to supplement core drilling to determine a conservative boundary between normal and questionable mining environments. A single channel seismograph, originally in use, is now replaced by a twelve-channel unit and is used to determine bulk material velocity which is the basis for defining the mining limit.

Jan 1, 1987

By Dennis L. Boley, Francesco Gallavresi, Donald A. Bruce

The authors describe novel aspects of ground reinforcement and treatment as related to soft ground excavation for tunnels throughout the world. Insitu reinforcement for cut slopes (soil nailing), as underpinning (reticulated micropiles), and as direct tunnel support (infilaggi) is introduced. Ground treatment focuses on new aspects of permeation grouting (by the tube'a manchette system), and on jet grouting-a very powerful and positive new technique. Recent developments in equipment, materials, methods and instrumentation are reviewed, with special reference to major tunnelling projects in Italy and Singapore.

Jan 1, 1987

By Madgwick J

A novel method for determining viable cells of the mineral leaching bacterium Thiobacillus ferrooxidans has been developed. The cells were collected on 0.45/Lm cellulose acetate filters, washed with artificial minewater, and incubated in the presence of ferrous ion at pH3 in an atmosphere containing radioactive (14C) carbon dioxide. Colonies of bacterial growth were detected by the image formed on X-ray photographic paper (autoradiography). The method was compared with three conventional techniques and shown to detect three orders of magnitude more cells in cultures of Thiobacillus ferrooxidans in the late exponential phase of growth.

Jan 1, 1987

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987