Search Documents

An enormous capital outlay is required to bring a new deep level (¦ 4 000 m deep) Witwatersrand gold mine into production. In addition, future mining methods must cater for rapidly rising working costs of which labour costs make up the largest portion. South African mining engineers are therefore being forced to challenge accepted design and valuation principles when planning these high risk ventures. New mining methods must be sought to satisfy the ever increasing need for productivity improvement. The technological problems posed by such changes cover a wide range of disciplines. Aspects of shaft design and configuration, besides being examined in the light of productivity, must also consider the rock mechanics implications at depth. Mining methods must anticipate and prepare for extremely hostile conditions due to seis- micity and virgin rock temperatures.

Jan 1, 1986

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

By Y. G. Zhang

Interactive Dynamic Optimization Method (IDOM) will be presented in this paper. IDOM combines inventory theory, dynamic programming, computer simulation and interactive technique to formulate a production schedule for open-pit mines. This new method has been successfully used in metal mines of China for years.

Jan 1, 1986

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By Paul F. Richardson

Liquids containing suspended solids are encountered in most mineral processing applications. Solids levels cover a very wide range, from ppm levels in cooling water systems to slurries containing greater than 70% solids. When the aqueous phase is recycled or further processed, a solid/liquid separation process is used. Chemical additives used to carry out this process are called coagulants and flocculants. In other cases, one seeks to control or modify the properties of the suspension. Dispersants are chemicals used to aid in suspending solids in a liquid as well as to control the properties of the resulting suspension. Dispersants find a range of uses in mining and mineral processing such as scale control, filter aids, flotation aids, and slurry viscosity modification. Materials used as dispersants include inorganic salts, alkalies, organic surfactants, and polyelectrolytes. This paper discusses the use of dispersants in mineral processing, with an emphasis on control of slurry viscosity. The mechanism of dispersion and factors that affect the choice of dispersant will be discussed.

Jan 1, 1986

Reverse circulation (R.C.) drilling or the dual tube method as it is quite commonly known, has a unique place in conventional mineral drilling. It can be classified half-way between open hole drilling at the lower end of the scale and diamond drilling at the upper end. The system basically consists of two tubes, one inside the other, with compressed air flowing between the inner and outer tubes. Sample cuttings return up the inner tube through the head of the rig and via a hose to a cyclone where the sample is collected. This system means that the cuttings are free of contamination as they are at no time in contact with the outside formation of the hole.Reverse circulation drilling is divided into two areas: R.C. Roller and Blade for softer formations; and R.C. Percussion for harder formations.

Jan 1, 1986

By E. C. Watkins

The fiber glass industry is an industry that. hopefully is still in its infancy and far from a mature business. Fiber glass, as will be discussed in this paper, deals with continuous strand glass as used in the textile laminate and reinforced plastics industries. More specifically, we are speaking of glass used for printed circuit boards, tapes, paper, cloth, pipes, tanks, boats, recreational equipment, roofing shingles, and automotive applications. Compared to the flat, container and decorative glass industries, we are very young. The early patents on fiber glass applications were issued in the 1930's. The type of glass most commonly used in the world and that discussed in this paper is designated as "E" glass. This is a boro-silicate type glass having specific chemical and electrical resistance and low thermal expansion properties.

Jan 1, 1986

By K. L. Ludeke, A. D. Day

For many reasons, it appears that deep rooted, perennial shrubs offer potential for improved stabilization and provide maintenance free vegetative cover to harsh sites where perennial grasses have not been successful. The major objective was to select various shrub species of arid plants for initial soil stabilization of disturbed mining areas. The very fact that a drought-adapted shrub has a massive root system that can use moisture from a greater volume of mineral waste soil materials suggests that arid environment disturbed soils may be vegetatively stabilized using desirable forage shrubs. A secondary effort is underway to assemble information and plant materials of promising species from many arid regions of the world for reclamation of mined lands. Surprisingly, many of the better plants for arid sites are quite high in protein content. With proper management, breeding, and selection, they may prove to be very desirable livestock feed when mined lands are used in range land areas. Advancements in arid land solid waste stabilization hold favorable promise for many industries that mine and mill in arid regions for effective reclamation of disturbed areas. Particularly exciting is the possibility of establishment of high density maintenance free vegetative cover of climax vegetation that reclaims the disturbed area back to its original land use. Due to high shrub productivity, stabilization potential, nutritional quality, and reclamation success, greater use should be made of shrubs in disturbed land reclamation associated with mining and milling operations in harsh aril environments.

Jan 1, 1986

By G. M. (Frits) Swinkels

The Apex property, mined in the early Twentieth Century for direct shipping copper, also contains gallium and germanium in iron oxide minerals. In 1982, Musto Explorations Limited began an exploration program to define reserves. A metallurgical process was developed, and a production decision was reached in late 1983. This text describes the process development and design. The Apex mine, located near St. George in Southwestern Utah is owned by St. George Mining Corporation, a subsidiary of Musto Explorations of Vancouver, B.C. Musto acquired the property in early 1982. A pilot plant was operated by Hazen Research, Inc., Golden, CO later in 1982. In late 1983 sufficient information had been developed for St. George to proceed with the project. The final process design was prepared by G. M. Swinkels of Vancouver, consultant to Musto, and Hazen Research. Process engineering was done by Hazen Research, and St. George acted as its own contractor. Commissioning of the plant began in October 1985.

Jan 1, 1986

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL HYDROLOGIC REGIME The total hydrologic cycle must be considered when evaluating potential ground water problems in a mining environment. Precipitation is the ul¬timate source of all surface water and essentially all ground water. Stream flow during low flow periods often orig¬inates as seeps or stream gains (base flow) where the water table intersects the land surface. A stream that is higher in elevation than the ground water system may lose flow, thereby recharging the ground water system. The magnitude of stream gain or loss is dependent upon the hydraulic conductiv¬ity and related properties of the underlying hydrostratigraphic units. Ground water moves constantly from recharge areas to discharge areas (streams and springs) usually at very slow rates. Large quantities of ground water may be in¬tercepted in many underground mining environ¬ments. Construction of an underground mine in saturated formations may encounter ground water inflows ranging from very small to very large and from continuous to intermittent depending upon the hydraulic properties of the hydrostratigraphic units penetrated. SURFACE WATER VARIABLES Precipitation occurs in different forms, varying amounts, and with a wide assortment of temporal and areal distributions in the various mining dis¬tricts within the United States. Mine inflow can be affected in a matter of hours by precipitation events where there is a direct hydraulic interconnection between the mine and the surface through fractures or a mine opening. The timing, form, amount, and distribution of precipitation should be evaluated in a mine inflow study. A portion of the precipitation that falls in a topographic basin moves as sheet flow to runoff channels (Fig. 1). Some of the precipitation infil¬trates the unsaturated soil zone where it can either move laterally as interflow to the surface system to augment stream flow or move downward as re¬-charge to the ground water system. The unsatu¬rated zone (called the zone of aeration or vadose zone) can range in thickness from essentially zero to a few hundred feet. The saturated zone or ground water system occurs below the water table (zone where hydrostatic pressure is greater than atmos¬pheric pressure) where all the pores are filled with water (Freeze and Cherry, 1979, p. 44). Moisture can be lost from any of the systems (surface water system, unsaturated zone, and ground water sys¬tem) by the processes of evaporation and transpir¬ation which return moisture to the atmosphere. Stream flow consists of runoff and interflow components plus an additional base flow compo¬nent (Fig. 2). Base flow constitutes ground water discharge to a stream. Base flow plays an increas¬ingly significant role as total stream flow declines. Base flow is important because it constitutes much if not all stream flow between periods of precipi¬tation when runoff and interflow have largely dis¬sipated. INTERACTION OF SURFACE WATER AND GROUND WATER SYSTEMS Recharge from a surface water system to ground water systems can occur via unsaturated or saturated flow. The amount of recharge is depen¬dent primarily upon the vertical hydraulic conduc¬tivity of the formations underlying the stream and the availability of water. Streams that flow over low hydraulic conductivity formations lose little water even if the ground water levels are significantly lower than the stream. A ground water system may contribute flow to a surface water system but nor¬mally only by saturated flow. This contribution usually takes the form of seeps, springs, and the base flow of streams. GROUND WATER VARIABLES Introduction The variables that affect ground water flow are discussed in increasingly complex theoretical situ-

Jan 1, 1986

By G. B. McClurg

China was nota factor in the supply of fluorspar to the United States until the early 1980's when it shipped in its first package of Metallurgical lump, that not only was higher grade than the Mexican Metallurgical spar but was also about $30.00 a ton cheaper landed at Burnside. Representatives of the Mexican Fluorspar Institute and several producers made trips to see the Chinese operations supplying their once reserved market place. China, an enigma to most Westerners suddenly became the new contender, with prices that were disgustingly low or so thought the other exporters. Of course China has been mining, producing, consuming and exporting from 400,000 to 500,000 tons per year of various grades of fluorspar but until the first partloads came to the U.S., very little attention was paid to their exports by American-continent producers or consumers.

Jan 1, 1986

By S. A. F. Murrell, M. Hong, L. J. Bond

This paper investigates the propagation, interaction and scattering of explosively generated seismic waves with discontinuities in rock masses using numerical models which employ a finite difference method. The models consider 2-D systems and give a full solution including mode-conversion in the mid-frequency scattering region where feature dimensions are of the order of the wavelengths involved. The paper has two parts, the first of which considers wave propagation and diffraction by simulating an explosive body source in a half- space containing a step or a slot on the surface which represent a cliff and a rift valley that has dimensions of the order of the wavelengths in the source. The second part of the paper reports a hybrid technique which combines a perturbation method and the finite difference method for wave propagation again caused by an explosive body source in a 2-D half-space system but with a shallow surface obstacle, such as a smooth ridge, with elastic constants slightly different from bulk material and the slope of this surface topography are shallow. This hybrid technique is also reported being applied to a half-space with a horizontal void or insert.

Jan 1, 1986

By Lama R. D

The Australian underground coal mining industry is undergoing major changes. This paper analyses the technologies presently being researched in mines, and discusses their utilisation as major contributors in the underground mining of coal in Australia over the next 20 years. It describes the problems that underground mining of the year 2000 will face and the possible solutions to those problems based upon results of present day research. Methods, equipment and organisational requirements are outlined. Developments in micro-electronics, computerisation and monitoring will require a new look into human resource development, education and training, and organisation to meet the challenges of the 21st century. The mining system's philosophies of the future are Outlined.

Jan 1, 1986

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

By Renee Y. Allee

The Chino open pit mine, concentrator, and smelter are located in Grant county in Southwestern New Mexico. Chino Mines Company is a partnership, two- thirds owned and operated by Kennecott Santa Fe Corp., and one third owned by MC Minerals Corp. (Mitsubishi) of Japan. The concentrator, with a design capacity of 37,000 tons of copper-molybdenite ore per day, was commissioned in July, 1982. Further design modifications have resulted in an increase in throughput capacity to 42,000 tpd

Jan 1, 1986

By K. F. Unrug

Eastern coalfields have been extensively strip mined. In the past, contour mining left vast areas of post-mining highwalls and benches. Thin seams, which cannot be feasibly mined with conventional methods, quite often contain substantial reserves of high quality coal. Unconventional secondary recovery methods may permit economical production of that coal, increased use of reserves, and provide resources for restoration of orphaned land. Technical and rock mechanics implications of secondary mining methods are discussed to determine their limitations and the objectives of required research.

Jan 1, 1986

By Peter V. Avotins

During last year's AIME meeting in New Orleans, Deepak Malhotra and I were discussing some of the topics that would be presented in this Symposium. It seemed appropriate that along with papers on specific reagent and flocculant types, we should address research management aspects of new product development. This development is a long, arduous task that requires a significant technical and fiscal commitment by the chemical company and potential users. A flow chart depicting the research process is shown in Figure 1. The sequence of events are plotted on an undefined time line. Our experience has shown that it takes 3-5 years to complete a typical reagent development project. A new project starts with an idea of how to do something better. The ideas range from relatively simple product modifications to opportunities created by technological change. An example of this is the use of flocculants in tailings operations to close the water recycle loop. The change was brought about by the need to conserve water and comply with environmental statutes. The result was the development and wide-spread use of synthetic polymers to help in solid-liquid separation. More recently the ups and downs of oil prices have led to development of coal water slurries as an alternative to fuel oil. The slurries contain high levels of chemicals (up to 3%) to insure proper stability and burn characteristics. There are technical changes under way right now that may lead to ideas for other new products. One exciting source of new technology is the ability to manipulate genetic material of microbes to select for specific capabilities. This has evolved by leaps and bounds over the past 5 years. Biologically assisted leaching and removal of wastewater impurities are two possible end uses. I'm sure that there are many others. The ideas can originate anywhere and are often half-baked at first, but to lead to new products they must be refined to provide project definition and eventually a research plan. A chemical ,development project cannot be started without approval to commit the company's resources. The internal selling job is often very difficult. The company must see clear financial benefits in order to launch efforts that may not pay off for many years. It is critical to project the total market, profitability, eventual market share, and timing of introduction of the new product. There is much uncertainty in this and the research manager is often skating on thin ice to retain his credibility. Once we obtain support from upper management, the research team is assembled to start the project. The teams generally consist of organic chemists, research metallurgists, and technicians. They have access to analytical scientists and technicians for surface and analytical chemistry. The projects are often augmented by help from university staff and consultants. This is particularly true where there is a need to develop fundamental understanding of the technology in addition to synthesis of chemicals. The project now proceeds along two lines. First, there is an emphasis on understanding the prior art. Extensive literature and patent searches are undertaken to provide research leads and to keep from "reinventing the wheel" and infringing on someone else's patent. The scientists and technologists are qualified to conduct computer-assisted library searches. This process usually uncovers 80-90% of the relevant information. The remainder is very much harder to get and requires the help of professional library search staff with scientific backgrounds. Along with literature searching, the team begins synthesis of new compounds. These are screened by use of techniques such as microflotation or filtration in a Buchner funnel. The scientists are looking for the direction of response as they modify structural features . Inevitably, a large number of candidates reach the next stage, a laboratory bench test. At this point it is possible to set up a research plan and use project management techniques to monitor progress. The bench tests are conducted in larger equipment, usually requiring 100-1000 grams of test substrate. Typical laboratory flotation tests are run in Denver or Wemco cells.

Jan 1, 1986