Search Documents

By Manuel Gomez

Dehydrogenation factors, proximate analysis, and ultimate analysis were examined as predictors of the low-temperature -carbonization properties of coals varying in rank from lignite through anthracite. All factors studied contributed to reduction in variance of the sample populations investigated. Response surface regression models based on variables from proximate and ultimate analyses of coal were constructed for eight low-temperature carbonization assay product and gas component Fields. These models were tested with independent samples that included drill cores, sized fractions, petrographic fractions, and run-of-mine coal. The models developed were used to predict low-temperature carbonization yields or coals from major fields of Wyoming. This information was cast in the form of contour plots describing the potential low-temperature carbonization product yields of Wyoming coals and the properties of the resultant char or coke. The variables used as input v the models may be measured and collected during exploration; thus, the carbonization properties of a seam can be determined in advance of mining. The information presented in this report is useful in that it broadens the deciionmaking base for management when either mine locations or coal conversicl plant sites, or both, are being considered.

Jan 1, 1971

By William F. Haddon, Phillip J. Maddex

Marco Polo brought the first borax to Europe late in the 13th century. It was especially treasured then for one of its many qualities-that of working with gold as a soldering flux. Georgius Agricola in 1556 gave it the name chrysocolla (which the Moors called borax)-literally, "gold glue." Deposits of borax have been elusive and widely scattered-first found only in Tibet and Italy, and, in 1836, at Iquiqui, Chile. Dr. John Veatch made the first California discovery in 1856 while examining a mineral spring east of Red Bluff. This "Borax Lake" soon supplied 90% of U.S. demand, but flooding and other production problems caused the scene to shift from Borax Lake to Little Borax Lake and then to Nevada in 1871. Early transportation was by "Twenty-Mule Teams."

Jan 1, 1971

By G Ride

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in arid areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1971

By A. M. Lovelace

Introduction One area of engineering utilization of materials in which the requirements are especially rigorous and demanding is that of aerospace systems, including aircraft, helicopters, missiles, and space satellites. Materials used in these systems must reliably perform many critical functions in a broad range of adverse environments. Some of the most critical functions are performed by polymeric nonmetallic materials such as elastomers (rubber), coatings, fibrous materials, and reinforced plastics. These types of polymeric materials have some common characteristics that make them attractive to aerospace system designers: light weight, corrosion resistance, and relative ease and low cost of processing and fabrication. Each type also has its own special characteristics that enable it to perform certain required functions better than other competing materials can (Table 1). The desirable properties of polymeric materials, which in some applications make them the only practical candidates, are partly offset by their principal limitation, which is degradation by exposure to high temperature. [ ]

Jan 1, 1971

By Lawrence A. Garfield

From the bottom of a shallow fissure the near-naked man-animal hacked out a hand-sized chunk of the red rock-like material which, when beaten between other rocks, could be drawn out to the thinness of a flint edge. Unlike flint, however, it did not shatter when, as the point for a spear or arrow, it went wide of its mark and fell amongst the rocks or tree branches. For this reason and others, the red rock- like material was specially sought and much time was spent in trying to break it from the real-rock in which it grew. Only infrequently was a chunk broken free and in this area many hours had been spent to win but a few fragments. What luck then, to remove so large a piece where before nothing but real-rock dust formed whenever the stone hammer hit. Why did this happen? Did yesterday's food-fire, burning on top the red rock, loosen its hold on the real-rock and cause it to break free when struck with the stone hammer? It is not a matter of recorded history that the first heat assisted extraction of native copper from country rock occurred under the circumstances or in the manner related but it is known that crude mining operations using these techniques were conducted by primitive man. In this way the first mineral production may have been achieved and the original example of rapid excavation unknowingly given to the world. Rapid excavation is not a method of removing rock or ore from an insitu condition nor does the term refer to a type of equipment which is specifically employed in mining and underground construction. It is, rather, the nomenclature currently popular in industry-primarily in underground construction- relating to a comparative rate of performance.

Jan 1, 1971

By A. D. Pernichele

Four types of slope failures in waste dumps are recognized; debris flow, foundation failure, edge slump and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is considered to be the most dangerous because of its explosive mode of failure and lack of forewarning. The December failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicated that the impounded water was due to a zonal accumulation of Jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1971

By W. P. Dyrenforth, W. E. Horst

Although, separating or concentrating minerals, based on differences in. their magnetic properties has been practiced for years1 the early industrial applications of magnetic separators were involved with the most highly magnetic materials. These early separators were used to concentrate magnetite, separate metallic iron from furnace products, and separate iron and brass turnings. Next, the addition of a pretreatment operation, such as roasting or calcining, to transform certain iron-bearing minerals into a highly magnetic compound that could readily be separated from the altered mineral mixture using existing magnetic separation machines was added to the flowscheme. As the number of magnetic-separator installations grew, steady development of better equipment evolved including the design and implementation of induced magnets having high-intensity fields, These developments of course greatly expanded the field of magnetic separation and made it possible to commercially separate or concentrate very weakly magnetic minerals which previously had been considered as nonmagnetic minerals. A number of different designs of magnetic separators were well developed and the unit operation of magnetic separation was gaining wide acceptance in mineral processing operations when two events occurred that dampened these developments. First, the Mesabi iron range with its direct-shipping iron ore was discovered and placed into operation. This of course significantly reduced the need for magnetic separation to meet the raw material requirements of the iron and steel industry. Second, the advent of selective froth flotation, was so successful in solving many mineral process problems that electrical concentration techniques being developed at that time, including magnetic-separation methods, were either terminated or received low priority ratings. During the past two decades interest has been renewed in the use of electrical concentration methods to solve mineral separation problems. As the direct-shipping iron ore reserves are depleted more emphasis has been placed on magnetic upgrading of lower value iron ore available throughout the world. In addition, magnetic separation techniques have found numerous applications in the non-metallic and industrial minerals industry to supplement froth flotation and thus add to the variety of beneficiation methods available.

Jan 1, 1971

By John Mitchell, C. C. Hanninen, L. D. Clark

INTRODUCTION Certain rock types can be fractured thermally by spallation and thermal cracking. Spalling occurs in the regions subjected to thermal shock temperatures and cracking takes place in the adjacent cooler regions. The analysis of the heat-affected zones requires that heat transfer calculations be made where the thermal conductivity of the rock is a function of temperature and direction. Generally, accurate thermal conductivity data is not available for the high temperatures and rise rates associated with most thermal rock breaking methods. This paper describes a method for determining the thermal conductivity of an orthotropic material whose conductivity is a linear function of temperature. The necessary data is obtained from one test which makes it especially useful for in situ applications. The properties data are determined through an iterative process of comparing theoretically computed values of temperature for assumed conductivity parameters with data measured in the laboratory. The conductivity of the rock is determined when the results of the assumed parameters yield computed temperatures which agree with those obtained experimentally. Transient temperatures are computed using the explicit numerical method at given points in a three-dimensional semi-infinite solid whose surface is symmetrically heated on a circular spot. The thermal conductivity is assumed to be a linear function K = [a] + Bt; however, if necessary, any reasonable linear or non-linear function might just as well be used. The stability, convergence, node size,

Jan 1, 1971

By Teder R. I., M. M. Protodyakonov

In order to find an empirical relation between a quantity F and (m) independent variables or factors, each of which take (n) different values or levels, it is necessary to conduct nm different experiments (all possible combinations of the factors), each of which has to be repeated a few times (usually five) due to the scattering of the data. The total number of such experiments is very large, thus for example, when m = 4 and n = 5, it is equal to 5.54 = 3125; and very rarely is it possible to conduct such a number of experiments. Various possible methods of planning partial experiments are illustrated in Fig. 1. Each method shows a large combinative square consisting of five columns and five rows of middle squares, each of which, in turn, is further divided into five columns and five rows of cells. Such a partition corresponds to a plan of an experiment with four factors, each of which takes five different levels. The blackened cells indicate the combination of factors in a partial experiment. The total number of experiments is reduced on the basis of the following considerations: a) The effect of only a few levels of some factors is studied (Fig. la). Such an investigation gives no information on the effect of some factors, therefore it cannot be accepted as satisfactory; b) By reducing the number of levels of each factor; in such a case it is not possible to obtain an empirical relationship, but only whether some factors have an effect. This is evidently inadequate;

Jan 1, 1971

Phase II of President Nixon's economic game plan will incorporate many top flight metals mining companies. The large corporations must receive approval from the Cost of Living Council before increasing prices and or wages. The theory here is that, with large companies complying with advance approval, smaller firms will be examined more closely by government, and thus will be forced also to comply. Rep. Paul McCloskey (R.-Calif.) called for a moratorium on strip mining for "the few years involved before we adopt a national energy policy and a national land use policy." McCloskey, who is a cosponsor of Congressional legislation that would outlaw strip mining, told a hearing that a "moratorium can scarcely hurt us until national energy and land use policies are adopted."

Jan 1, 1971

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the' same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By G. C. Milligan

"A regional mapping program, conducted by the Nova Scotia Department of Mines, has shown that the George River Group of pre-Middle Cambrian rocks consists of a wide range of sedimentary and volcanic rocks, intruded by syenite, granite, granodiorite and lesser amounts of gabbro and diorite. Together, these rocks support the high ground of northern Cape Breton Island. Over this large area, the metamorphic grade ranges from low to extremely high.The rocks were folded prior to emplacement of the intrusions in Middle Cambrian time, and there was also post-Mississippian disturbance and faulting, but the structural history and pattern are still only imperfectly understood.Sulphide mineralization is known at Meat Cove, Lime Hill and in a number of smaller deposits. The most Cavour-able host rocks appear to be magnesian Iimestone, or schists derived from shales. Ail known sulphide bodies have an associated halo of retrograde metamorphism; in some cases, this is extensive enough to be used as a prospecting aidA vein of nickel-bearing sulphides has recently been re-discovered in the former gold mine at Second Gold Brook-an association which appears to be unique."

Jan 1, 1971

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By Wayne L. Johnson

The depth capability of engineering seismographs has been greatly increased by the use of signal enhancement, a technique in which seismic waveforms created by repeated impacts are digitized, stored, and summed. Summation amplifies the signal and partially cancels background noise. This gives a clearer picture of the wave aid makes it possible to determine the travel tune of signals from 'eater depth. Signal enhancement combined with continuous display of waveform, permanent recording of waveform, and precision digital readout of travel time has opened new fields of application in mining and engineering. Recent work has clown that replacement sulfides can be distinguished seismically from country rock at Bistee, Ariz. Work on the Iron Range of Minnesota indication,: that, by using a 300 pound weight as the source, the Biwabik iron Formation can be traced down dip to several hundreds of feet traverses over known areas show that reflections can sometimes be identified. Reflection, if identified preclsely, give a mere accurate estimate of depth and buried topography. Comparison of ( ) and weight drop have given some understanding of low wave amplitude varies win; source candid

Jan 1, 1971

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By E. Morrice

The effect of the temperature of SmF3-LiF electrolyte on the electrolytic preparation of samarium-cobalt alloy by the consumable cathode technique was investigated. The temperatures of the cathode zone, alloy collection zone, and samarium oxide (Sm203) feed zone had to be controlled carefully to obtain a satisfactory samarium-cobalt alloy product. Any appreciable deviation from certain temperature values adversely affected yield and product quality.

Jan 1, 1971

By Roy H. Paddon

This paper describes the 6, 000 tpd, three stage haulage system at the Ozark Lead Company's mine in southeastern Missouri. It details the methods and problems pertinent to the loading, hauling, sorting, crushing, storing and hoisting of waste rock and ores obtained from underground development headings and production areas. The Ozark Lead Company is a wholly owned subsidiary of the Kennecott Copper Corporation. Its mine is located nine miles south of Bunker in Reynolds County at the south end of the "New Lead Belt" mining district. Development started in May, 1964, by drilling a seven foot diameter (six foot cased), 1, 250 foot development-ventilation shaft. Drifting began in August, 1965, to obtain a bulk ore sample, to test ore continuity, and to drive two mine levels while the pre-grouted production shaft was being sunk. Over 7, 900 feet of 12 by 24 foot drifting was done from this small shaft. In March, 1966, a 20 foot diameter, three compartment, concrete lined production shaft was collared. It intersected existing development headings at a depth of 1, 195 feet in April, 1967, and was completed along with a concentrator and other facilities in June, 1968. Mine production began that month, with 5, 000 tpd reached in 1970.\

Jan 1, 1971