Search Documents

By William T. Ingram

Early in the 60's the author served as Chairman of the Engineering Foundation's Coordinating Committee on Air Pollution Research. One of our objectives was the development of a study on the measurement of stack emissions. Three publications of the Foundation resulted from these efforts to focus attention on the stack sampling problem.1,2,3 Two of these were annotated bibliographies covering 197 references. The third reported the results of a workshop meeting at which some 21 individuals from research institutes, industry and government discussed the possible and probable areas of research that would add to or increase the ease, precision and utility of sampling gaseous and particulate matter emitted from stacks. The American Society of Mechanical Engineers has had in its Power Test Codes a Standard Code for Determining the Dust Concentration in a Gas stream4 since 1941, The American Industrial Hygiene Association has published, in its Air Pollution Manual,5 a Section on Stack Sampling. Industry and regulatory agency requirements for stack sampling have utilized some modification of the alternatives in methodology. There has been ho single guide to stack sampling that met the needs of those who have the need to know.

Jan 1, 1970

By Eugene E. Brucker

In recent years, there has been increased interest in construction problems presented by karst topography. Twenty-five years ago, karst areas were by-passed for development. Today, the high cost of land and population pressures are requiring utilization of karst areas. Areas exhibiting karst features can be satisfactorily developed so that construction can proceed in a normal manner; or the areas may be left undeveloped and the underground drainage system abused by improper use causing or contributing to structural collapse, excessive erosion, and a grave threat to the stability of land development and the environment. The term "karst" is a comprehensive term applied to areas underlain by soluble rock that possess a topography formed chiefly by the dissolving of rock and the diversion of surface waters to underground routes. There are four features which contribute to the maximum development of karst. 1. A soluble rock, preferably limestone, must be present at or near the surface of the ground. Occasionally, dolomite will suffice.

Jan 1, 1970

By J. H. Swisher

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By G. B. Craig, H. E. Rosinger, W. J. Bratina

NUMEROUS studies have been reported on how the mechanical properties of a bcc metal are affected by interstitial solute atoms in the temperature range where appreciable diffusion occurs in finite time. Only recently, though, has work on an "interstitial-free" iron been reported, this by Leslie and sober,&apos; on an Fe-0.15 pct Ti alloy. The data was limited to a maximum temperature of 296°K. This work presents a systematic study of the flow stress and the activation volume of a similar material as a function of plastic deformation over the temperature range 253" to 473°K. The material studied was Ferrovac E iron containing 0.01 wt pct C and 0.0002 wt pct N annealed at 870°C for 1 hr, and the same iron with an addition of 0.15 wt pct Ti annealed at 870°C for 80 hr; cooling rates being 75°C per hr. In the latter alloy depletion of interstitials in the a-iron matrix associated with the second phase formation was expected. The temperature dependence of the flow stress was measured at 6 = 3.33 x 10-5 sec-1 from 253" to 473°K as a function of the deformation in 0.01 intervals from 0.03 to 0.12 strain. Results for two strains, 0.03 and 0.09 are shown in Fig. 1. The flow stress increased and reached a maximum in the Ferrovac E iron with increasing temperature, but showed a consistent gradual decrease in the Ferrovac E-0.15 pct Ti alloy. A yield point and Luders region, observed in Ferrovac E, was absent in the Ferrovac E-0.15 pct Ti alloy. Also, the Ferrovac E exhibited a serrated stress-strain behavior in the temperature range 330" to 400°K; dynamic strain-aging characteristics were absent for the titanium alloy. The activation volume was determined over the same temperature range by the method of stress relaxation at constant strain. Results are shown in Fig. 2. At the temperatures of serrated stress-strain behavior in Ferrovac E the activation volume was found to increase toward infinity and, as the temperature rose, to decrease, to about 100 to 200 v/b3. By contrast, the activation volume for the Ferrovac E-0.15 pct Ti alloy tended to increase continuously from the initial value of approximately 300 at 300°K to more than 800 at 473°K. Above 400°K, then, the corresponding activation volume values of Ferrovac E were less than that of the Ferrovac E-0.15 pct Ti alloy. The activation volumes, Fig. 2, appear to depend on dislocation-interstitial interaction in Ferrovac E and on dislocation-dislocation interaction in Ferrovac E-0.15 pct Ti alloy. The gradual increase in the latter metal is associated with thermally activated motion of dislocation segments.&apos; The decrease of the activation volume in Ferrovac E above 400°K is probably related to the diminishing effect of interstitials on dislocations. Here, the interstitials can be moved along with a dislocation without appreciable drag. As indicated in Fig. 1, removal of interstitials

Jan 1, 1970

By K. D. Sheffler, R. W. Hertzberg, R. W. Kraft

The Ni-Ni,Ti lamellar eutectic alloy responds to unidirectional solidification by alig-nment of the platelets of the two phases roilghly perpendicular to the moving solid-liquid interface. X-ray diffraction and zetallographic experimenls show that the following cryslallographic relationships exist in the directionally solidified ingots: lamellar interface w [0001] Ni3Ti 11 (111 }Ni local growth direction (1120) Ni3Ti n (110) Ni These relationships are rationalized on the basis of the crystallography of the constituent phases. In recent years researchers in several laboratories have shown that an aligned or "controlled" micro-structure can be produced in many binary eutectic alloys by forcing the alloy to solidify unidirectionally in an elongated crucible.&apos;-3 It also has been found that a unique crystallographic relationship often develops between the two phases in such a structure.4, 5 Since a parallel arrangement of phase particles in an alloy should, and, in many cases, does, produce unique and highly anisotropic properties, the alloys so produced are of potential interest in a variety of applications. Studies of these alloys are also of interest at the academic level because they help to improve our basic understanding of the way in which metals solidify. This paper reports the metallographic and crystallographic structure of another of these alloys—that between nickel and Ni3Ti. In a separate paper, hot tensile and stress rupture properties as well as deformation and fracture behavior of the same alloy are discussed.19 EXPERIMENTAL DETAILS AND RESULTS General Characteristics of the Eutectic Reaction. Several small exploratory Ni-Ti melts were made to resolve a conflict in Hansen6 over the eutectic composition. The alloy containing 16.4 at. pct Ti, Fig. 1, appeared metallographically to be closest to the eutectic composition, although small dendritic patches of proeutectic nickel are present. The eutectic morphology is lamellar and appears quite sharp and angular, indicating a strong influence of crystallographic factors upon the microstructure. Some of the eutectic nickel platelets are continuous with the primary phase, whereas in hyper eutectic melts a "halo" of nickel generally surrounded the proeutectic inter-metallic platelets, indicating that nickel is the nucleating phase in this eutectic reaction. Extensive precipitation of Ni3Ti has occurred in the primary nickel phase in a Widmanstatten pattern which makes the dendrites difficult to differentiate from the eutectic mixture. This phenomenon may account for discrepancies among the eutectic compositions reported in the literature. The sloping solvus line bounding the nickel primary solid solution explains the presence of the intermetallic precipitate. Poole and Hume-Rothery7 report that the solubility of titanium in nickel drops from 13.8 at. pct at the eutectic temperature (1304°C) to approximately 9 at. pct at 700°C (Ni3Ti, on the other hand, melts con-gruently and exhibits essentially no solubility for nickel or titanium). Lever rule calculations based upon Poole and Hume-Rothery&apos;s phase diagram indicate an increase from 21 vol pct Ni3Ti in the eutectic mixture at the eutectic temperature to 61 pct at room temperature. Selective point count measurements of the volume fraction of eutectic Ni3Ti platelets in the eutectic microstructure yielded a value of 46 i 2 vol pct, which required extensive precipitation of Ni3Ti from the nickel solid solution onto the eutectic intermetallic platelets during cooling from the solidification temperature. Influence of Directional Solidification. Nickel bar and titanium sponge of 99.9 pct purity were induction-melted in zirconia crucibles under argon in the proportion of 13.8 wt pct (16.4 at. pct) Ti to produce 14-lb master heats which were cast into investment molds yielding 5/8-in.-diam pins approximately 10 in. long. These pins were remelted under argon in horizontal zirconia boats and unidirectionally solidified to produce 1/2-in.-sq ingots approximately 44 in. long. Details of the experimental techniques and apparatus are described elsewhere.&apos;

Jan 1, 1970

By R. A. Wattenbarger, H. J. Ramey

The trend in gas well testing has been to rely more on the early-time flow data of drawdown and buildup tests than on stabilized flow tests. The stabilized testing methods often are not adequate for complicated modern gas reservoirs because many of these reservoirs have extremely low permeabilities and the transient flow period of a well test can last for days or weeks. It has become common to augment the flow capacity of gas wells by hydraulically fracturing their producing formations. In deep reservoirs the induced fractures are generally vertical and tend to follow a single plane of weakness. The presence of a vertical fracture at the wellbore complicates the transient flow behavior of a low permeability gas well. The flow is further complicated when turbulence occurs near the wellbore. Russell and Truittl published transient drawdown solutions for vertically-fractured liquid wells. They developed methods of drawdown and buildup testing utilizing these solutions, which were based on numerical simulation. Clark2 applied the basic Russell-Truitt solutions to analyze fractured water injection wells by falloff tests. Field examples were given to substantiate the method of analysis. The Russell-Truitt solutions and well testing methods can be extended to gas well flow. Millheim and Cichowicz3 presented the drawdown equations for *Now with Scientific Software Corp., Denver. ideal gas flow, including the effects of formation damage and turbulence. Two actual field cases were presented, both of which exhibited extensive fractures and turbulent flow. For the pressure range of these well tests, the use of ideal gas equations was acceptable. These field cases were significant in being the first published data showing the occurrence of turbulence in fractured gas wells. We, also, observed such cases in practice. Our purpose here is to extend the theory of fractured gas well testing to the flow of real gases. To determine the effects of wellbore storage and turbulence on well test interpretation, we developed a finite-difference model to simulate well test conditions. Since gas wells usually are widely spaced and have high compressibility, the emphasis has been put on the early transient behavior before the effects of the outer boundary are noticeable at the wellbore. The Mathematical Model The geometry of our mathematical model is similar to that used by Prats.4 The well is centered in a circular uniform reservoir. A vertical fracture of infinite flow capacity penetrates the formation and passes through the wellbore. The wellbore itself is not important. Fig. 1 shows a sketch of the problem. Fig. 2 shows the idealized model. The equation for the flow of real gas in a porous medium with uniform porosity, permeability and thickness is5-7

Jan 1, 1970

By Herbert Dlaska

The BBU - rotary hearth treats lead concentrates and battery scrap by the roast-reaction process. It corresponds in principle to the long-known Newnam hearth, however its hearth-basin is not straight but curved to a closed ring. In operation this annular hearth is filled with liquid lead and rotates around a central blast-box. The charge, heated to a glowing-red, floats on top of the lead bath, into which air is blown from the blast-box through a horizontal slot-type tuyere. Ore pellets and brown coal are continuously charged onto the reacting mass from two storage bins. Lead is set free by the roasting reactions and trickles through the charge into the lead bath from where it is tapped from time to time. The reacting mass is continuously stirred by a mechanical agitator and backed, by a mechanical shovel, against the water-jacketed wall of the blast-box. The gangue of the charge forms lumps of scorified character, the so-called hearth slag or grey slag, which are discharged from the hearth. The waste gases are collected in a hood and conducted to a baghouse from where the fumes and dust are automatically transported to the pelletizing installation and are recycled with new material. The daily output of lead bullion depends mainly on the lead content of the charge. With lead concentrates containing 74% lead, about 24 tons of lead bullion per day are produced on the hearth at a direct lead recovery of about 89 per cent. Approximately 10 per cent of the lead content of the new material passes into the hearth slag from where it can be recovered in a blast furnace or in a rotary furnace. For small lead smelters the BBU-process represents the most economical way of melting high-grade lead concentrates. The process requires a relatively small capital investment, consumes little fuel, utilizes cheap fuel and is very flexible. Further, of great importance, is the fact that battery scrap can be treated by the BBU-process with very good results.

Jan 1, 1970

By Lloyd B. Underwood

Dr. Gardener, in Chapter 2, has presented a comprehensive state-of-the- art review of site investigations For tunneling. Nearly all of the techniques he discussed will also be required for future site investigations. Therefore, this chapter will be devoted to a few rather new exploration techniques plus ideas for improving some of the present-day methods. In March 1962, the first symposium on "Remote Sensing of Environment" was held at the University of Michigan.l Since that time, four additional symposiums have been held at the same University. Also, the technical Literature has recently included a number of articles on remote sensing techniques. A recent one appeared in the February 1968 issue of Materials Research and Standards.Vt was entitled "Developments in Remote Sensing Applicable to Airborne Engineering Surveys of Soils and Rocks," and was written by Dana C. Parker. Mr. Parker predicts that aerial reconnaissance will someday supplant soil augers, rock drills, surface reconnaissance, and geophysical surveys as the engineer&apos;s primary means of obtaining information about soils and rocks. He states, "The engineer wishing to survey a route or a site or to locate rock and soils suitable for construction projects will be able to push some buttons in an airplane and record all the data required for determining the relevant conditions. In a short time after he returns to earth with his rolls of film and charts, he will be able to reduce and analyze the data by partially computerized techniques and to compile a concise and comprehensive engineering report that gives all the relevant information about rocks, soil, water, and vegetation in the area he surveyed. Most important he will feel as confident with his recommendations, derived primarily from image characteristics and spectral power distributions, as his predecessors did with recommendations based on more tangible evidence obtained from drill cores and surface reconnaissance." The airborne sensors for engineering surveys of soils and rocks are those that sample some electromagnetic property of the materials that com- prise the terrain and cover its surface. In addition to cameras, these include

Jan 1, 1970

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y&apos;, and E carbonitride has been confirmed and it has been found that y&apos; is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part&apos; reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,&apos; this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* &apos;Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

By Thomas E. Howard

Tunneling is at the threshold of a new era. An exciting new technology is becoming available. And, supplying the increasing quantities of minerals required by a growing and socially advancing world population, together with providing the subsurface facilities attendant to the rapid urbanization of the more developed countries of the world, will require underground excavation during the next decades on a scale that would have seemed fantastic a few years ago. It is estimated that world mineral consumption will increase fivefold by the year 2000. Projections for the United States indicate that domestic consumption of nonfuel minerals may increase two to three times by the end of the century. Meeting these requirements will entail opening up many new underground mines, even if present trends toward surface mining continue. And, at least in the United States, new factors that are becoming increasingly important may modify these trends. We are depleting our shallow easy- to-find and easy-to-mine mineral deposits; and, if we are to avoid becoming dangerously dependent on imports, we must turn more and more toward deeper deposits that are not amenable to surface mining. Growing public concern with environmental quality is apparently leading toward increasingly stringent regulation of surface mining which also will tend to make underground mining economically more attractive. The world market for underground construction is also growing rapidly. The most conservative projections indicate that in the United States alone more than $7.0 billion will be spent on excavation for underground facilities during the next ten years. And these estimates do not include any of the bold, imaginative new applications for underground excavation that have been proposed, such as extensive underground power transmission, the Chicago Deep Tunnel plan, and the Northeast Corridor Transportation project. There can be little doubt then that the market for tunnels for conventional applications is increasing rapidly and that the trend will continue. It

Jan 1, 1970

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,&apos;~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro&apos;~ suggested that the strain E can be deduced

Jan 1, 1970

By Richard H. Johnson

White Pine Copper Company, a subsidiary of Copper Range Company located in Michigan&apos;s Upper Peninsula, mines a Precambrian sedimentary deposit containing finely disseminated chalcocite, native cop- per and native silver. Silver occurs predominately in certain strata and presently provides a mill head averaging 0.25 ounces per ton. This technical publication traces the development of silver recovery at White Fine beginning in early 1961. White Pine refined copper contains an excess of silver over and above that required to impart Lake Copper properties. The copper does not require electrolytic refining to meet industry purity requirements, nor is there sufficient silver to justify electrolysis.

Jan 1, 1970

Aspects of the formation, decomposition and acid solubility of zinc ferrite were examined to find potential ways of increasing the recovery of zinc from a calcination process of mineral concentrates. Ferrite can begin to form within 2 hours at 450¦C. while complete reaction can occur after 35 minutes at 700¦C. The nature of the starting materials has a pronounced effect on the rate of formation and below 700¦C. ZnSO4 and Fe2O3 proved to be the least reactive of the materials investigated. It is possible that iron in a mineral admixed h sphalerite can be converted to a relatively inactive form, however, it does not seem possible to prevent zince f formation when iron is in the sphalerite lattice. At the two temperatures examined, 650¦C. and 700¦C, the presence of SO2 in the atmosphere accelerate .e formation of ferrite. Prolonged exposure to such atmospheres, however, caused the ferrite to decompose to ZnSO4 and Fe203. The optimum temperature for decomposition was 650¦C. and it was virtually complete within 2 hours in an atmosphere of 10% SO2 in air. Zinc ferrite was also decomposed by CO at low concentrations, and by heating with limestone at 1000¦C. for at least 2 hours. The solubility of zinc ferrite in acid was influenced by the starting materials used. As both the reaction temperature and the time at temperature increased the acid solubility decreased. The acid solubility was a minimum when the ___i_.. n - I -r~...................c -..... F, fe..i+e --A frn... A01- +^ Z(lo/

Jan 1, 1970

By B. B. Rath, Hsun Hu

In wedge-shaped bicrystals of zone-refined aluminum it is observed that (111) pure tilt boundaries migrate under the driving force of their own inter-facial free energy. The boundary velocity is a power function of the driving force. The driving force exponent decreases with decreasing angle of misorien-tation. For example, at 64O°C, the exponent decreased from 4.0 for a 40 deg to 3.2 for a 16 deg tilt boundary. An evaluation of the driving force acting on the boundaries during their motion indicates that for low driv-forces, up to about 2 x l03 ergs per cu cm, the velocity is relatively independent of misorientation, whereas at higher driving forces a 40 deg tilt boundary exhibits the highest velocity. The measured activation energy for boundary migration approaches that for bulk self-diffusion at low driving forces, decreasing from 33 to 27 kcal per mole as the driving force is increased from 1 x l0 to 5 x l03 ergs per cu cm. These results are compared with current theories of grain-boundary migration. In previous experimental studies of grain boundary migration the driving force has been limited to a difference in stored energy across the boundary. This stored energy has been introduced into the crystal either by prior deformation1-3 or by grown-in lineage structure. A part of the energy stored in the deformed crystal is released by recovery either prior to or concurrently with grain boundary migration, thus introducing an uncertainty as to the magnitude of the driving force responsible for grain boundary migration. The grown-in lineage structure, though thermally stable during annealing, neither provides conditions under which different levels of energy may be stored in the imperfect crystal nor provides a control of orientation difference across the migrating boundary of a growing grain. Furthermore, because of variation in the lineage structure, it is difficult to determine accurately the energy stored in the imperfect crystal. Several investigations of grain boundary migration during normal grain growth have also suffered from difficulties in estimating the driving force because of uncertainties in the principal radii of curvature.~ In the present investigation the velocity of pure tilt boundaries in zone-refined aluminum bicrystals of selected orientation (40, 30, and 16 deg around the [Ill] tilt axis) has been measured in the absence of a dislocation density difference across the moving boundary, thus eliminating the previous experimental difficulties. The driving force for boundary migration is derived from a gradient of the total interfacial free energy of the migrating boundary in wedge-shaped bicrystals. A similar method was attempted by Bron and Machlin in a study of grain boundary migration in silver. However, they found that one of the crystals was deformed and consequently the motion of the boundary was partly due to a difference of stored energy across the boundary. The observed behavior of boundary velocities as affected by the driving force is examined in the light of the predictions of the current theories of grain boundary migration.7"10 The effect of boundary misorientation on velocity is compared with the theory of " which is based on a dislocation core model for high-angle boundaries. EXPERIMENTAL METHOD Seed-oriented bicrystals of zone-refined aluminum, 2.5 cm wide, 0.5 cm thick, and 12 cm long, containing tilt boundaries with a common (111) axis, were grown from the melt in the direction of this axis. Spectro-graphic analysis, reported earlier,&apos;&apos; indicated the purity of the crystals to be 99.999+pct. Three such bicrystals containing 16, 30, and 40 deg tilt boundaries were used. Wedge-shaped specimens were prepared from these bicrystals by spark cutting followed by electrolytic polishing. The angle of the wedge was usually 40 deg and the specimens were usually 0.25 cm thick. The intercrystalline boundary was located within 0.2 to 0.5 cm from the tip of the wedge. Fig. 1 shows a section of an oriented bicrystal containing an outline of a wedge-shaped specimen. The crystallographic directions shown in Fig. 1 represent the orientation of one of the crystals (the larger section of the bicrys-tal); the orientation of the other crystal differs only by rotation around the common [lil] axis. The parallel faces of the wedge always corresponded to the common (171) planes in both crystals, whereas the orientation of the side faces varied, depending on the misorientation angle. The bicrystal orientations were determined

Jan 1, 1970

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By Phil Allen

A synthetic fiber manufactured by one chemical company has been treated by another chemical company to produce a cloth fabric capable of performing ion-exchange functions. Only a few delimiting parameters have been established. This paper will discuss briefly the highlights of a functioning ion-exchange cloth. Throughout the paper this fabric will be referred to as "Fabric Z".

Jan 1, 1970

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By Kenneth G. Colman

Even though wet processes were used in coal preparation plants prior to 1941, dewatering coal was not a problem then because the finer sizes were uneconomical to recover and were considered waste. However, during the war years the scarcity of raw materials necessitated the utilization of every pound of natural resources and coal plants began seeking an economical mans of recovering fine coal. Early efforts to this end concentrated primarily on centrifugal dewatering devices. Such equipment produced good results but was relatively expensive. In 1944, a method was devised utilizing a vibrating screen fitted with a profile wire deck rather than the standard woven wire cloth deck. This machine came to be referred to as a dewaterizer. Results obtained with the dewaterizer approached those of the centrifugal equipment, but at a lower capital cost, Their use reduced either the number of centrifugal units required to follow the dewaterizers or the required energy input to heat dryers, In some cases they eliminated the need for any further dewatering equipment.

Jan 1, 1970