Search Documents

By Gordon H. Geiger, John M. Svoboda

One mechanism of metal penetration into mold aggregates by cast steels is vapor state mass transport. In order to further understand and quantify this mechanism, the steady-state diffusion of metallic vapors was studied at 1250" to 1600°C in controlled oxygen pressure atmospheres by measuring the weight loss from a metal bath whose vapors were allowed to diffuse through a porous aggregate compact held at constant temperature. Mass transport rates substantially greater than those predicted from the assumption that the vaporizing species was the elemental metal vapor were observed. Vaporization rates were found to increase with an increase in the oxygen partial pressure in the gas atmosphere with maximum vaporization occurring at oxygen partial pressures just below those in equilibrium with a liquid oxide layer at the given temperature. When the liquid oxide layer was present, no vaporization was observed. Metal carbonyls were ruled out as the vapor species involved because of their thermodynamic properties. The species with the enhanced volatility were deduced to be gaseous metal-oxygen molecules, probably the polynuclear oxides (FeO)2 and (Mn0)2. Diffusion followed the ordinary diffusion mode, and Knudsen diffusion is not important in normal foundry molds. The interdiffusivities of the metallic vapors and the mold atmosphere, through the porous aggregates, were measured. The effective interdif-fusivity of the vapor species and mold atmosphere through the aggregate may be expressed as follows: Deff,12 - — where E is the void fraction of the aggregate and 7 is the "tortuosity factor". Aggregate material had no effect on diffusion rates, and the only relevant parameter was the void fraction. Values for 7 ranged from 3 to 6 for normal foundry aggregates with 4 being considered a good representative value. An area of interest in high-temperature metallurgical processes which has received little attention in the past is the diffusion of metal vapor species in porous aggregates. Research into the metal penetration phenomenon' in foundry molds has shown that a major penetration mechanism is the vapor transport of metallic species into the porous foundry sand molds, followed by condensation of metallic films on the sand grains. Considerable study of the vaporization of metallic species has been reported in the literature, and the vapor transport properties of many metallic species have been determined.2'3 Many instances have been observed where the vaporization behavior could only be explained by the existence of a metallic species with a vapor pressure greater than the elemental metallic species. These species were identified or, in some cases, presumed to be carbonyls,4,5 hydroxides,6-9 or vaporous oxides.10-16 The diffusion of gases through porous aggregates has received considerable attention in the literature pertaining to catalysis, although primarily at low temperature, and more recently in the literature concerned with ore reduction.17-22 The following experiments were devised and carried out in order to determine the nature of the metallic species involved in the metal penetration phenomenon, and the effective diffusivities involved. EXPERIMENTAL APPROACH Steady-state diffusion was selected for experimental convenience. The experimental systems used, shown in Figs. 1 and 2, consisted of a porous aggregate specimen contained in an impermeable alumina tube held above, and just separate from a metal bath. The entire system was held at constant temperature and pressure in a furnace with a controlled oxygen partial pressure atmosphere. After a brief period of nonsteady state behavior, a steady flux of metal vapor through the porous aggregate will develop due to the concentration gradient of metallic vapor in the gas phase. The flux of metallic vapor from pressure may be neglected because there is no pressure gradient. There is no flux from convection because there is no net flow of gas within the metal-aggregate system, and thermal diffusion is negligible compared to the flux from ordinary diffusion. If the material being studied is allowed to vaporize until steady-state behavior is attained, the experimental results may be analyzed using Fick's First Law.

Jan 1, 1970

Jan 1, 1970

By Ted C. Briggs

Twenty-two compressibility runs were made with helium over the temperature range -5° to 80° C and at pressures to 800 atmospheres. A Burnett apparatus was used. Data from the runs were fitted to a fourth degree polynomial equation of state in the pressure and a weighting factor of Pr-3/4 was used. All data for a particular isotherm were treated simultaneously. A temperature function was found to represent the parameters B and C. Compressibility factors determined by this investigation are believed to be accurate to better than 0.05 percent.

Jan 1, 1970

By Fathi Habashi

LEACHING IS the process of extracting a soluble constituent from a solid by means of a solvent. In extractive metallurgy it is the process of dissolving a certain mineral (or minerals) from an ore or a concentrate, or dissolving certain constituents from metallurgical products such as calcines, mattes, scrap alloys, anodic slimes, etc. In this respect, either one of two purposes can be achieved: 1) Opening of ores, concentrates, or metallurgical products to recover the metal values. 2) Leaching easily soluble constituents (usually gangue minerals) in an ore or a concentrate in order to have it in a more concentrated form, e.g., the

Jan 1, 1970

By John F. Abel

A good mining engineer is supposed to make a good mine. What then makes a good mining engineer? There certainly are a lot of answers to that question. The answers depend on whether you are one, work for one, or employ one. There are several cliches about mining engineers, and there is some truth in them-as there usually is in any stereotype. Hollywood chose Jeff Chandler to portray a mining engineer in Foxfire. The image here was of an almost one-man mining operation. When Chandler picked up a jackhammer, cradled it in his gut and started drilling out a tunnel round, it gave one the hives. I would have liked to see him finish just one round that way. There are limits to what even the most hairy-chested of us will try. We can assume that Hollywood feels it needs to over- draw any profession to add impact.

Jan 1, 1970

By E. J. Bonet, P. B. Crawford

It is fairly common practice to reinject water into the aquifer near the oil-water interface in water-drive reservoirs. There have been many studies of aquifer behavior without reinjection,l-5 but apparently no analytical studies have been made to indicate performance when injection wells are present in the aquifer. The diffusivity equation may be used to describe the pressure behavior in an aquifer. When sources are present it can be written as A general solution of Eq. 1 may be obtained as the sum of two solutions. One is a general solution of the homogeneous equation, obtained by dropping the source term in Eq. 1 and still satisfying the required boundary conditions. Another is a general solution of Eq. 1 satisfying homogeneous boundary conditions.1° The first solution, which corresponds to the aquifer without reinjection, has been given quantitative and qualitative treatment in the literature.l-5,8,9 The latter solution will be treated here. Solutions with variable injection rates are obtained by superimposing solutions with constant rates, so we have considered only the latter. Five cases have been treated here: 1. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The pressure along the line x = 0 is maintained at zero pressure. (See Fig. 1.) Equations showing the pressure distribution, rates, velocity and cumulative influx have been developed. Certain numerical results are shown. 2. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The rate of production along the oil-water water contact is maintained constant. Equations showing the pressure distribution inside the aquifer are presented. 3. A linear aquifer of finite width and extent. Constant pressures are maintained at opposite ends of the aquifer. Water is injected at constant rates at point xo, yo. Equations showing the pressure distribution are shown. 4. A linear aquifer of finite width and infinite extent. The pressure is maintained constant at the oil-water contact. Water is injected at a constant rate at point xo, YO. 5. A linear aquifer of finite width and finite extent. The pressure at the oil-water contact is maintained constant. Water is injected at constant rate per unit length along a line x,. The Linear Aquifer The linear closed aquifer, performing at constant terminal pressure was selected as the first case to be analyzed. The development of the equations is based on uniform injection per unit of thickness, and gravity effects are neglected. In practical application this condition is probably most closely achieved when the

Jan 1, 1970

By Neal P. Cochran

It is always a pleasure for me to address a group of mining engineers. I am doubly grateful when I am allotted sufficient time to describe the total Office of Coal Research program. My remarks are directed to our total program but I trust you will all understand my emphasis of the utilization aspect of our activities since that is my portion of the program. From its inception, the Office of Coal Research has sought out creative ideas for improving our national use of coal by developing new uses, improved mining procedures, lower costs, and appropriate studies with respect to the resource itself. Quite early in the game, our Economics and Marketing Division contracted for studies with respect to New England export market, Western coal, and similar items. Our Mining and Preparation Division has successfully developed a packaged coal-fired boiler and has partially developed a packaged fluid-bed type boiler as well. Our Mining and Preparation Division is working in such diverse fields as treatment of sewage with coal and the separation of coal into distinct-petrographic constituents so that all fractions of the coal can be put to the best possible use. We would like to be doing more work on improved mining methods, better preparation techniques, and any other mining improvement that will benefit the industry and our program. The synthetic fuel plants I will describe later will operate seven days per week, 24 hours per day. We would like the mine to operate on this same sort of cycle and are prepared to support research that will lead to this.

Jan 1, 1970

By N. N. Moebs

The Bureau of Mines air-sealed a 77-acre) above-drainage coal mine to evaluate sealing as a means of reducing the acid and metallic salt contents in drainage from abandoned mines. An approximate reduction in acidity of 150 ppm (equivalent to 193 pounds per day) and in iron of 98 ppm were directly attributed to sealing. The topographical, hydrological, and other factors involved in air-sealing are discussed, and the construction used to seal the mine is described.

Jan 1, 1970

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

By Freeman Bishop

The tight electric power supply is one of the most dramatic problems facing the mining industry in 1971. This is caused by rising demands for energy. Clean-fuel and air-pollution controls have contributed to the problems of producing energy from sulfur oil and coal. Coking coal has become scarce. One stimulating development is that coal is no longer the cinder in the mining industry's eye. In fact, it may be the favorite candidate as a base for fuel within a few years. Synthetic gas from coal is the watchword. In dedicating a multi-million- dollar project aimed at converting coal into oil and gas, Hollis M. Dole, Assistant Secretary of the Interior, recently made it clear that coal, which has been taking a back seat to nuclear fission research and study grants, is now coming into its own. Conversion pilot plants are being activated in all parts of the nation.

Jan 1, 1970

Jan 1, 1970

By Allen L. Hatch

A survey of all phases of the world's lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies and the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world's lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950's and 1960's.

Jan 1, 1970

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By J. Szekely

A rrlethod is presented for the estitnation of oxygen pickup by teettzed molten steel streams. Of the mechanisrt~s considered for oxygen absorption, physical entrainment appeared to be the most significant. The estent of this physical entrainment may be calculated by the application of boundary layer theory. It was found that the values of oxygen pickup thus predicted were in wry good agreement with data reported in the literature, in the case of short, well-defined metal streams. This entrainment model does not provide an adequate description of oxygen pickup by long streams, exoosed to external winds and where breakup of the streatn is likely. WheN molten steel is teemed into a mold or tundish it will absorb oxygen contained in its environment. Recently interest has been expressed in the measurement and possible prediction of the extent of this oxygen absorption: this interest owes its existence to two principal factors: a) the desirability of providing a quantitative assessment of the role played by the absorbed oxygen in impairing the quality of (vacuum degassed. stainless, or continuously cast) steel; b) the need for providing guidelines for stream protection methods. The purpose of this communication is to suggest a simple method for the prediction of oxygen absorption by continuous metal streams and to compare the predicted values with the data available in the literature. It is hoped that this method may provide at least an initial framework for the interpretation of additional data that might become available. FORMULATION Consider a continuous metal stream falling into a molten metal pool as depicted in Fig. 1. This system may absorb oxygen due to the following two mechanisms: 1) physical entrainment of gases (including oxygen) into the molten pool where reactions. thus absorption, will occur; 2) mass transfer (convec:tive diffusion) of oxygen to the metal stream. 1) Physical Entrainment. The physical entrainment may be calculated by using the concept of the diaplace-ttzent tlzickness of the laminar boundary layer, which will be stated briefly in the following.&apos; When a fluid flows past a solid surface, a portion of the fluid close to the surface is retarded due to fric-tional forces. This region in which the velocity of the fluid differs from that in the main stream is called the boundary layer. An illustration of this is given in Fig. 2 where it is seen that the thickness of the boundary layer increases as we move along in the x direction. In the laminar region, when Re, < 10&apos; the thickness of the boundary layer is given by the following relationship: f =4.64 Re;1" [1] where 61 is the boundary layer thickness, x is the length along the leading edge, Us is the velocity of the free stream, (i is the viscosity of the fluid (gas in this instance).

Jan 1, 1970

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory&apos; is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2&apos;3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin&apos;s suggestion that the free liquid/air interface

Jan 1, 1970

By M. J. Langley

The American Zinc Company’s mining operations in East Tennessee are located in Knox and Jefferson Counties. Mineralization occurs, intermittently, through a strike length of more than 30 miles, from near the eastern edge of Knoxville northeastward to a few miles beyond Jefferson City. The presence of zinc in these Counties has been known for well over 100 years. In 1910 it was brought to the attention of American Zinc Company that zinc sulphide deposits in the Mascot area might be attractive. Following an examination and some surface prospect drilling, the American Zinc Company of Tennessee was organized and acquired the Mascot properties in 1911. Operations began in 1913 on the basis of 1,000 tons per day mill capacity. With the successful operation of the Mascot mines, the Company undertook explorations in the area from Jefferson City southwest through Friends Station to Mascot. The efforts resulted in development of substantial tonnages of zinc ore and enabled the Company to expand the Mascot and New Market milling operations to their present capacity of 11,100 tons per day. Folded and faulted Paleozoic sedimentary rocks under- lie the mining district. The principal zinc mineralization occurs in a group of strata known as the Knox

Jan 1, 1970

By M. Earl Volin, M. Adnan Goksel

The hydro thermal agglomerating process described (U.S. Pat. No. 3,235,371, 1966)* is different from the cotzventional high-temperature processes. Green pellets or briquettes made with mixtures of moist iron-ore concen- trates and burned or hydrated lime fines are hardened in an azttoclave at 198°C and under steam pressure for 112 to 5 hr, with or without previous drying. Under the neutral conditiotzs, oxidation of magnetite does not occur as in the conventional processes. The resulting azzlomerates-- are hard and resistant to abrasion and weathering, and they do not disintegrate in the Under test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperamre and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1970

By J. Szekely, V. Stanek

Heat and gas flow interactions in nonisothermal packed beds were examined in the paper. A study was made of the response of the system to a step or pulse change in the inlet gas temperature, with a fixed value of the overall pressure drop across the bed. Under these conditions the heat flow and fluid flow transients are coupled because the convective heat transfer rate is alfected by the mass flow rate of the gas which, in turn, for a fixed pressure drop will depend on the temperature profile in the system. The Problem was stated in terms of differential equations, which were integrated numerically. The parameters used in the computation were so chosen to reflect the operation of the stack region of blast furnaces and sinterbeds. The computed results showed that the pressure drop-flou1 relationships and the rate of progress of the temperature fronts (waves) were strongly interrelated and were also markedly affected by variations in particle size and in void fraction. MANY metallurgical processes involve the contact of solid particles with a gas stream in a packed bed arrangement under nonisothermal conditions. Examples are shaft furnaces, regenerators, pebble heaters, and the sinter process. Although the heat and mass transfer aspects of packed bed processing have been extensively studied, the associated flow phenomena and in particular the effects of nonisothermality on the flow, have received little attention to date. :In fact, most of the previous workers considered the flow rate of the carrier gas time invariant and independent of the heat or mass transfer processSzekely and carr2 have shown that the pressure drop-flow relationships in nonisothermal packed beds may be strongly affected by the temperature profile within the system. These authors have devised a method for relating the pressure drop to flow for a given temperature profile. thus providing an extension of the Ergun equation to steady nonisothermal systems. Finally, in a recent paper willmot3 examined the response of regenerators to externally imposed changes in the gas flow rate. Both these investigations were somewhat specialized since, in general, neither the temperature distribution nor the gas flow rate may be regarded as truly independent variables, thus the heat transfer and the fluid flow problems have to be solved simultaneously. The work reported here is divided into two parts: in Part 1 the general formulation is given and a detailed discussion is presented of fixed bed systems. Part is devoted to systems in which a gas and particulate solids are contacted in a counter flow arrangement. FORMULATION Consider a nonisothermal fixed packed bed, extending from through which a gas is flowing. The problem is to develop a relationship between pressure drop and gas flow (with the gas flow being the dependent variable) and to evaluate the rate at which a change in the gas temperature, imposed at the inlet, travels through the system. Let us consider an infinitesimal section of the bed and establish differential heat, mass, and mechanical energy balances over this region. In addition, relationships are needed describing the temperature dependence of gas density (equation of state) and the temperature dependence of viscosity. These may be written as: where c, and are constants. It is noted that in this formulation we neglected any temperature gradients within the solid particles, thus assuming these to be either sufficiently small or of sufficiently high thermal conductivity to meet this condition. The justification and consequences of this assumption will be mentioned in the discussion.

Jan 1, 1970

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By Rollin A. Slater

This paper presents a composite of ideas on materials handling systems by describing the design of an over-all system for a hypothetical steel pellet plant located on the Great Lakes. The bulk materials handling industry has served for years as the skeleton and the central system of nerves and nourishment for the body of basic industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. Materials handling technology has likewise improved its techniques and currently has a new, stronger generation of equipment to perform its necessary supporting function. Drawing upon excerpts from several recent plant designs, this paper describes a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details are not available for publication, and therefore the plant described herein is a composite of ideas. This imaginary plant will be located on the United States side of the Great Lakes and its owner will be called the Hypothetical Steel Corp. for purposes of discussion. TYPES OF EQUIPMENT The basic bulk materials handling systems and components required in a plant so situated are: lake boat unloaders; railroad train unloading systems; storage pile stackers and reclaimers; large bins and regulating feeders; and the conveyor systems — with their attendant controls— which connect the foregoing. PROGRAM OF DEVELOPMENT The initial work on the plant must be that of the process engineers who develop and refine the basic data, i.e., the logistics of all raw materials, waste materials and products within the plant. During this phase of study, the materials handling engineer may advance his planning only in basic areas such as movements at the dock and movements at the railroad. This initial planning work is concerned only with defining logical plant locations in the light of channels, currents, existing traffic, governmental regulations, locations of existing railroads and available rights-of-way. These systems alone have their own individual criteria which must be respected and accommodated in the final layout. All other elements, such as the arrangement of the blast furnaces, power house, coke plant, by-product plant, scrap preparation plant, BOF shop, and facilities for continuous casting, degassing, calcining, etc., are dictated by their own specific needs and their relation to each other. In the arrangement of these latter facilities, the materials handling system is secondary and must be designed to accommodate. BASIC LOGISTICS The result of the process engineer&apos;s work can be expressed in terms similar to those shown in Table I. Plants are customarily rated in terms of annual tons of ingots. Therefore, the basic size of this plant can be determined by referring to the BOF Shop wherein it is sized at 5 million tpy. From the base, the required hot metal can be traced to the blast furnace, which in turn indicates the amount of required flux, iron bearing materials and coke —which in turn establishes the demand for coal. Likewise, the total demand for flux can be determined by the combined demand of the lime plant and blast furnace. The generation of fines and waste products, which have significant value but are not usable as such, create the need for a sintering plant. From projections such as the foregoing, the complete flow of materials can be established and accommodated. The basic premise upon which this typical materials balance is predicted is that the plant will be a producer of high tonnages of non-SpecialtV- products. All basic raw materials (flux bearing, iron bearing, coal) will be prime quality. For example, the basic iron charge will be pellets, and the iron ore fraction will be sized lump, all of which

Jan 1, 1970