Search Documents

By Robert W. Hunt

The first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 71/2 inches diameter; eight inlet and eight outlet valves of 24 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington's proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 363/8 inches diameter, by 36-inch stroke, with water-plungers of 961/2 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steamcylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By M. R. Henzen, J. W. Funke, G. J. Stander

SYNOPSIS The adverse effect of acidic mine drainage derived from gold and coal mining operations on the quality of receiving waters is described, together with measures to be taken to counteract this pollution. The mineral load and the toxic effects from metallurgical and metal finishing industries are also considered. Attention is drawn to water conservation aspects.

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10.00, Annual subscription R17.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription R15.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription R15.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.

By Dean H. Ambrose

This paper presents a technique for representing and analyzing random motions and hazardous events in a computer simulated three-dimensional workplace, providing machine designers and safety analysts with a new technique to evaluate ways to reduce operator-machine interaction hazards. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. By simulating motions of an operator's random behavior and a machine's appendage, researchers can accurately identify hazards, and use that information to form safe designs for mining equipment appendage velocity. Validating the model provided improvements in the operator's optimal viewing area, work task- starting positions, and operator's motions for a more accurate random behavior. Preliminary simulation results provided (1) an interesting approach to research data gathering in that there was no need for live subjects and test sites and costs associated with experiments become insignificant and (2) that the model was versatile by showing it was capable of accurately mimicking the range collision forces versus speed, operators' size, and risk behaviors found in actual industrial situations and showed (I) that response time significantly affects the number of collisions experienced by the virtual subject and (2) that analysts must be discerning with the model and not read more From the databases than what the simulation model was designed to deliver. Keywords: random human-motion, anthropomebics model, machine-operator hazards, mine safety

By Kris Chatrathi, John E. Going, Kenneth L. Cashdollar

Two types of flammability limits have been measured for various dusts in the Fike 1-m3 (1000-L) chamber and in the Pittsburgh Research Laboratory (PRL) 20-L chamber. The first limit is the minimum explosible concentration (MEC), which was measured at several ignition energies. In addition to the three dusts studied previously (bituminous coal, anthracite coal, and gilsonite), this work continues the effort by adding three additional dusts: RoRo93, lycopodium, and iron powder. These materials were chosen to extend the testing to non-coal materials as well as to a metallic dust. The new MEC data corroborate the previous observations that very strong ignitors can overdrive the ignition in the smaller 20-L chamber. Recommendations are given in regard to appropriate ignition energies to be used in the two chambers. The study also considered the other limiting component, oxygen. Limiting oxygen concentration (LOC) testing was performed in the same 20-L and 1-m3 vessels for gilsonite, bituminous coal, RoRo93, and aluminum dusts. The objective was to establish the protocol for testing at different volumes. A limited investigation was made into overdriving in the 20-L vessel. The LOC results tended to show slightly lower results for the smaller test volume. The results indicated that overdriving could occur and that ignition energies of 2.5 kJ in the 20-L vessel would yield comparable results to those in the 1- m3 vessel using 10.0 kJ. The studies also illustrate the importance of dust concentration on LOC determinations.

By L. J. Prosser, G. Esterhuizen, A. T. Iannacchione

The potential for roof fails in underground mines remains a clear and present danger for mine workers An investigation of ground conditions in nearly 50 percent of the nation’s underground stone mines fold that the slate of roof stability is primarily determined in a limited and subjective manner. These large-opening mines with roof heights typically 7 m (23 ft) or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information an roof stability, this practice is usually short term and localized to address ground conditions in a particular section or part of the mine. A roof-fall hazard-assessment techniques was development based on engineering judgment acquired from extensive underground stone mine experience and on exanimation of the related literature. This technique utilizes observational processes to determine roof fall likelihood Case-study scenarios offer a realistic picture of model implementation. Providing the mine level decision-maker with an accurate assessment tool to ascertain the level of ground fall hazards is expected to reduce mint worker injuries and fatalities Moreover; the presences of danger can be overcome with a clear picture of quantified ground conditions.

By R. Raines, S. P. Signer

Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health installed 39instrumented, fully grouted bolts at six test sites in a trona mine retreat panel to study mine roof stability for the improvement of workplace safety. Variables at each test site included bolt spacing, bolt length, roof span, and location in the panel layout. At most test sites, two rows of instrumented bolts were installed, one in or near the intersection created during development and the other in or near the intersection created during second-pass mining. The most significant factor affecting bolt load was roof span. The highest loads were on the bolts installed in the intersections of the 6-m-wide entry. Mining-induced stress resulting from panel layout was the next most significant factor affecting bolt loading. Minor variations in bolt loading could be attributed to changes in bolt spacing and bolt length. Gas pressure release in the immediate roof contributed to some bolts showing compressional loading during gas bleed-off.

By A. T. Iannacchione

Synopsis Underground stone mining Is an emerging sector of the U.S. mining industry. As this expansion takes mines under deeper cover, and as more efficient mining methods are utilized, effective stone pillar design methods will become even more Important. Current design practices are examined and a discussion of safe mine layouts is presented as a first approach towards weighing the demands for increased production against increased risk. Risks to underground stone-mine workers include rib Instabilities, pillar failures and roof falls. Seventy-two stone-mine pillar designs were examined. Pillars with width to height ratios of less than 1.5 appear more likely to fail when subjected to excessive stress levels. When width to height ratios fall below 1.0 defects in the pillars, such as through-running discon¬tinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties and orientation are also important determining factors in pillar strength. During the past three years the number of active underground stone mines in the U.S.A. has ranged between 90 and 100. This number is expected to increase as the crushed stone industry responds to growing demands for its products.1 As more of the industry moves to benefit from the advantages of underground mining production from underground stone mines is expected to increase above its current level of approximately 66 000 000 r/year. Parker2 identified four advantages of underground mining operations: (1) surface developments, zoning laws and environmental concerns are often less of an issue; (2) stripping and restoration requirements are eliminated; (3) additional reserves are often available beneath the quarry floor, under pit slopes or under an adjoining property; and (4) space is created for secondary use. Underground mines enjoy the added benefits of work in a constant underground climate, rather than in the variable surface climate, minimization of community concerns by placement of the crushing, sizing and stowing operations underground and reduction of surface vibration concerns through smaller blasts. The drawbacks of underground mining include added health and safety hazards for the stone miners, whose health can suffer from increased exposure to falls of ground, airborne contaminants and fog in large underground openings. Injuries from falls of ground in stone mines have occasionally exceeded the incidence rates for other mineral resources mined underground. 3 Existing underground stone operations, by comparison with stone operations a decade ago, mine more stone at a faster rate and with larger equipment. Because of high demand mines face increased pressure to yield more stone per production blast. A majority of the miners use the V-cut blasting pattern, which limits the depth or pull for each shot to about 4 m. Therefore, to produce more stone, either the mines must work more faces or existing faces must be enlarged. The enlargement of underground openings poses problems in the maintenance o€ strata stability, First, the widths of the mine entries partially control the amount of sag or deflection that any given roof beam can withstand before failure. This deflection can take pi ace quickly after an opening is excavated or much later as weathering processes form additional, thinner beams. Because increased deflection increases the potential for roof beam failure, there is a limit to how wide a room can safely be made. These limits depend on local geological and stress conditions and, to some extent, the cost effectiveness of roof-bolting. Given these room width limitations, underground stone mines have placed more attention on expansion of production through benching where mining thicknesses permit. The heights of rooms partially control the strength characteristics of adjacent pillars: as the room height increases for a given pillar width the pillar width-to-height ratio (w/h) decreases. In general, stone pillars are very strong, but when the width-to height ratio diminishes the potential for pillar rib instabilities and pillar failures increases (see Fig. 1). [ ] In the underground environment the desire to utilize wider rooms, higher benches and multi-level mining results in the potential for unstable ground conditions. Although the number of failed pillars is currently very low, the potential for additional failures will grow if more slender pillars are developed, especially under deeper cover, with wider mining sections and in multi-level operations. It should also be noted that the passage of time acts to decrease the strength of many existing pillars. An examination of current design practices

By E. B. Viljoen

I. R. M. Chaston* As a gravity concentration man in the midst of so many eminent flotation experts I feel like Daniel. However, I would respectifully disagree with the opening remarks by Mr Viljoen. First, he suggested that gravity concentration of cassiterite was not effective in sizes below 30 microns. In a paper to the Institution of Mining and Metallurgy in 19621, I gave some figures for gravity concentration of deslimed material both for cassiterite and for wolfram which indicated that careful shaking table concentration of fine deslimed material could give recoveries of 75 to 90 percent in the size ranges above 13 micron. These were figures obtained from normal plant operation. It would be interesting to know if any tests were carried out on gravity concentration of the efficiently deslimed feed to this flotation plant to see what the recovery would be. Secondly, Mr Viljoen suggested that gravity concentration plants were expensive. He gives the cost of a flotation plant at R300 000 to treat a feed of 400 t.p.d. to the desliming section or 160 t.p.d. to the flotation cells. From his operating cost figures it would appear that the flotation cost is approximately R2 to R4 per ton of feed to flotation and the total operating cost about R2 per ton of feed. A table plant to treat this tonnage of deslimed feed would consist of about 30 tables and should cost considerably less to install and very much less to operate than the flotation plant. Third, Mr. Viljoen suggests that the concentrate grade from a gravity concentration operation would be unacceptably low. The paper quoted abovel showed that once a primary fine concentrate had been made, giving a suitably deslimed material, further gravity concentration could give concentrates of over 40 per cent Sn with high recoveries. Tailing from this dressing stage was naturally returned to the feed. To give these high grades, sulphides had been removed by flotation but this necessary flotation step is simple and cheap to operate and could be restricted to the final stage when the quantities involved are small. I would agree that flotation has a part to play in fine tin recovery but this role would only seem to become fully effective at sizes below 10 micron and would seem to require, as Mr. Viljoen has suggested, a mechanism for sizing which is effective down to, say, 1 micron. In the meantime it would be interesting to try tabling the flotation tailing to see if it was possible to recover the plus 20 micron cassiterite which is not recovered well by flotation. One point which has been made during discussion is the suggestion that cassiterite particles have a fully hydrated surface at normal pH. I wonder if this layer could materially affect the overall specific gravity of a very small cassiterite particle and, if so, whether gravity concentration of the very fine cassiterite would be improved if carried out in acid conditions, which would inhibit the formation of this hydrated surface. REFERENCES 1. CHASTON, I. R. M. 'Gravity concentration of fine cassiterite'. Trans. Inst. Min. and Met. Vol. 71, p. 4, 1961 and 1962, and discussion of this paper. Dr. R. P. King Mr Viljoen has drawn attention to the difficulties associated with the presence of very fine particles in the flotation pulp and he has indicated that, on the Union Tin plant, they must sacrifice 30 percent of the cassiterite in the minus 7 /Lm material which they separate and lose. He has also indicated that the rate of flotation of cassiterite remained high at these small sizes. The problem arises because the very small particles stabilize the froth making it impossible to handle. These stable froths cannot be easily broken and therefore cannot be pumped and processed. It seems that further fundamental research work on the properties of stabilized froths is urgently required. We have found another difficulty associated with the presence of very fine particles in phoscorite slurries; these particles can be easily floated but with very poor selectivity. We believe that it is possible that a purely physical mechanism such as entrainment is responsible for the collection of fine particles in the froth. We have also demonstrated that the presence of fine particles in the pulp adversely affects the rate of flotation of the larger particles. For esample, we have found an increase in recovery of + 100 um material from 2 percent to 17 percent in a standard laboratory batch flotation test on phoscorite when the - 37 um was removed from the feed. Such interactions between particles are not universally recognised as an important aspect of the complex flotation mechanism. They should appear in any quantitative formulation of the flotation rate process.

By George G. Binder Jr., James W. Lacey, Arthur L. Draper

An experimental investigation of miscible fluid displacement has been made in linear porous media under highly adverse mobility ratio conditions. Various refined oils were displaced at field rates by liquid propane in both horizontal and vertical models 9 to 36 ft in length. In horizontal tests, mixed zones or transition zones form between the two liquids early in the displace-lents. Initially, the zones grow rapidly. III 2-in. diameter models, the mixed regions become nearly stable zones from 6- to 20-ft long. From then on these quasi-stable zones apparently grow only by molecular diffusion. The lenghts of the quasi-stable zones appear to be almost independent of the core material in which displacement;; are made and increase with increasing rates of injection and oil/solvent viscosity ratios. The lengths of the quasi-stable zones. measured in 2-in. diameter models at viscosity ratios and injection rates anticipated in the field indicate that essentially piston-like displacements of oil by solvent would occur. However, the mixed zone lengths increase markedly as the model diameter increases. In vertical displacements controlled by gravity drainage, only short trans-sition zones form. The entire lenghts of these zones can be accounted for by molecular diffusion. Therefore, in reservoirs having characteristics allowing a high degree of gravity drainage, nearly complete oil recovery should be attainable by miscible fluid displacement. INTRODUCTION The oil industry is faced with an ever increasing cost for finding new oil reservoirs. This, coupled with the fact that conventional methods of oil recovery usually leave from 1 to 3 bbl of oil in the ground for every barrel produced, has aroused considerable interest in developing more efficient methods. An integral part of the mechanism of many of these new methods of recovery is a miscible fluid displacement in which oil is displaced by a much less viscous materiai such as liquid propane. A numher of irlvestigators have explored the mechanics of miscible fluid displace-ment,'.2.1.'."." but in the experiments reported many of the important factors have been varied only over a limited range far removed from norma1 oilfield values. This paper presents the results of an experimental study of oil displacement by liquid propane at field rates from linear, natural-sandstone models of various sizes. Both horizontal and vertical flow tests were made. EXPERIMENTAL APPARATUS AND PROCEDURE Refined oils with viscosities varying over a wide range were displaced at several rates by liquid Propane from both horizontal and vertical flow systems. The behavior of the displacement was observed by propane-oil analyses of the effluent and, when possible, by differential pressure measurements along the cores. A schematic flow diagram of the apParatus used to conduct the experirents is shown in Fig. 1. The cores used in the tests were 9-ft lengths cut from natural consolidated sandstone and turned to the desired diameter. These were cast in steel tubing with a low melting point (160°F) alloy which expands on solidification. Flanges welded to the ends of the steel pipes permitted sealing the ends or butting one core to another. Pressure seals were maintained with O-rings. The cores were cleaned by flushing

By W. B. Potter

There is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

By T. Feldmann

Despite the ubiquity of applications for germanium, there is a lack of practically useful solubility data in acidic solutions. Previous studies were done at ambient temperature and only for commonly used acids (H2SO4, HCl). Hence, an investigation of the solubility of GeO2 in different acids was undertaken. Several inorganic and organic acids were studied in the concentration range of 1–11 mol/L and at 23, 40, and 60 °C. In the case of H2SO4 and HCl previous data was confirmed. Lower acidity resulted in a higher solubility for Ge at all tested temperatures. Tests done at 40 and 60 °C and low to moderate acidity levels, gave slightly increased solubility values at higher temperatures compared to 23 °C. This wasn’t the case at higher acidity levels, i.e., the solubility curves at different temperatures converge at high acidity. Lastly, a relationship of water activity and GeO2 solubility in different acid media was established.

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Jeffrey Johnson, Thomas Brady, Radford Langston, Mary MacLaughlin, Hendrik Kirsten

The magnitudes and directions of in situ stresses affect the stability of mine openings, as well as the type and amount of ground support needed to maintain a safe working environment for miners. Using hollow inclusion stress cells, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health obtained two in situ stress measurements from the face of two footwall lateral drifts at the Stillwater Mine near Nye, MT. The first measurement, obtained in 1997, was collected under the valley beneath the Stillwater River. The second measurement was obtained in 2002 under the main frontal massif of the Bear tooth Mountains in the western sector of the mine. Although few data are available, the major principal stress under the valley has been recorded as nearly horizontal in a north-south direction perpendicular to the ore body, while beneath the mountains, stress runs east-west parallel to the ore body. This paper documents the measurements, describes the in situ stress state, and discusses a finite-difference analysis of the biaxial test.

The June General Meeting of the Institute was held in Kelvin House, Johannesburg, on 18th June, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present fourteen Members, Messrs R. J. Adamson, F. P. Bath, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, and Mr P. W. J. van Rensburg (Council Members), Messrs B. F. Berry, A. F. Lee, J. E. van Leeuwen, G. G. Nicolson, N. F. Peverett, Dr A. G. Raper, Messrs E. R. Rudolph and H. R. Reid. Five Associate Members, Messrs T. D. Brown, M. R. Fuller-Good, J. S. Freer, Dr P. R. Jochens and Mr D. A. Viljoen. One Graduate, Mr P. G. Mrkusic. Five Students, Messrs N. A. Barcza, J. A. Cruise, R. P. W. Henrard, D. I. Ossin and J. C. M. Wethmar. Nine Visitors, Messrs M. Badenhorst, N. J. Bovey, H. H. Herold, Dr H. J. S. Kriek, Messrs M. S. Rennie, B. B. Segal, S. Selmer-Olsen, O. A. W. Strydom and B. Yates. Secretary, Mr D. C. Visser. Total present: Thirty-six. MINUTES The Vice-President: "May we confirm the minutes of the Monthly General Meetings held on 24th March, 16th April and 21st May, 1969 as published in the Journal?" Agreed. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Wilfred Desmond Morgan, Abraham Kriek. Associate Members: Rodger Neville Hampson, Robert Richard Booth Lodge. Graduates: Beverley Hugh Waiters, Gwynne Hugh Johnston. Students: Colin Edward Alvery, Peter Marthinus Haikes, Charles Aubrey Husband, John Nowell Randell, Frederick Johannes Jacobus Blaauw, Johannes Andries Breytenbach, Peter Vos, Frederik Hendrik Coetzee, Petrus Nicolaas Jacobus Smit, Patrick Alien Boardman, Robert Nelson Guest. "May I welcome the newly elected members to the Institute." (Applause.) ELECTION OF SCRUTINEERS FOR THE 1969-70 BALLOT FOR COUNCIL The Vice-President: "In terms of By-Law 9.4, I now call for nominations for scrutineers for the 1969-70 ballot for CounciL" P. W. J. van Rensborg: "I wish to nominate Messrs R. C. J. Goode, V. C. Robinson, J. K. E. Douglas, P. Lambooy, D. G. Maxwell, H. Britten and H. Simon as scrutineers."

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).