Search Documents

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Donald P. Tuchman, Robert P. Vinson, Jon C. Volkwein

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized ?lter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM®). Standard ?berglass TEOM ?lters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel ?lter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon ?ber candidate ?lters left minimal residual ash and produced no signi?cant spectral interference. Avoiding titanium dioxide in all ?lter materials proved to be a key requirement. Fine quartz particulates were collected on prototype ?lters in a Marple chamber, either open-faced or through PDMs during test runs. The ?lters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to ?lter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in ?lter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM ?lters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7–10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM ?lters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.

By J. Blodget Britton

During the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations mere made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phœix Iron Company, at Phœnixville, Pa., was found to have the composition given in Column I of the following table: I. 11. 111. Composition of Dust from Dust from Dust from Deposits. Blast Furnace. Puddling Furnace. Boiling Furnace. Protoxide of iron,... 1.51 3 08 1.18 Peroxide of iron,... 20.21 33.29 41.00 Alumina,....6.57 12.89 7.54 Lime,.....3.98 .48 .61 Magnesia,.....69 .09 .19 Protoxide of manganese,. . 1.66 .39 .12 Oxide of zinc,....2.84 ........ Oxide of copper,. .. ..06 ........ Silicic acid,....36.00 40.69 38.99 Sulphuric acid,... 7.55 .43 Phosphoric acid,..94 ..94 Arsenious acid,. .. .38 Antimoniousacid,... trace.......... Chlorine,....03 ..03 Cyanogen,.....09 ........ Ammonia,.... trace......... Pottlsh with some sodn,. .. 16.61 ........ Carbonic acid,. .. .. .59 ........ Alkalies, undetermined matter, and loss,.......29 4.49 6.96 100.00 100 00 100.00 Metallic iron,. 16.31 25.70 29.64 Phosphorus,. .. .. .41* 1.55† 1.30†

By Mathew P. Oommen, Jeffrey L. Kohler

Computer-aided loadflow and fault analyses of mine power systems are routinely conducted to ascertain system performance and also to provide information to assist in the protection and coordination of these systems. Three-winding transformers are frequently encountered in mining applications, typically at continuous miner and longwall sections where there exists a need for dual utilization voltages. These transformers are often modeled as a three-bus system neglecting the secondary to tertiary winding impedance and the effect of base changes. This paper analyzes the impact of more accurate transformer models on voltages and fault currents which are realized from loadflow and fault studies of mine power systems.

PRESENT Minutes of the Annual General Meeting, held on Friday the 20th August, 1971, at 7.45 p.m. in the Boulevard Hotel, Witbank. Mr J. Meintjies in the Chair, 15 Fellows, 7 Members, 2 Associate Members and 10 Visitors. Mr Meintjies extended a welcome to all the members and their wives, and the many visitors and their wives. A special welcome to Mr Robinson the outgoing President of the Institute and Prof. Howat the President Elect and Mrs Howat. The minutes were read and adopted. The Chairman read his Report for the past year and also the Financial Statement. Mr E. Jackson proposed the acceptance of the Financial Statement and Mr Winship seconded it. Mr Meintjies thanked Mr Vic Robinson for all the help he had given throughout the past year. He also thanked the outgoing Committee for their support, and the Secretary for arranging the function. Mr Meintjies congratulated Mr Alex Bain on his election as Chairman and asked him to continue with the meeting. Mr Bain thanked Mr Meintjies for the good work which he had done in the past year and then announced the names of the Committee for the ensuing year. A. Bain Chairman G. Carlyon Vice Chairman J. Meintjies Past Chairman I. Botha E. J. Jackson A. W. L. Brereton B. D. McNiece N. J. P. Coetzee A. N. Turner B. T. Hosking W. D. Winship Mr B. D. McNiece proposed a vote of thanks to the retiring Chairman. The meeting closed at 8.10 p.m. Dinner was served and after coffee Mr Vic Robinson gave a most amusing and informative review of the Institute's activities. Mr Bain thanked Mr Robinson for his address and Prof and Mrs Howat and Mr Robinson for coming down to Wit bank for our Annual General Meeting.

By Charles M. Rolker

The Allouez Mine is situated in section 31, town 57, north of range 32 west, Michigan. The mine is being worked in a conglomerate bed, which conglomerate is generally conceded to be the continuation of the Albany and Boston conglomerate of Honghton County. Besides the well-known Calumet and Hecla with the adjoining Osceola, both working on the same bed, and the new location, the Seneca, now being tried on the Kearsarge conglomerate, the Allouez Mine is the only one working on a conglomerate bed. The Albany and Boston, in Houghton County, of which, as said before, the Allouez is supposed to be the continuation, shares with all the remaining conglomerate beds, near and around Portage Lake, the property of being non-quartziferous, while the conglomerates of Keweenaw County are all highly quartziferons in character. This change takes place, according to Professor Pumpelly, about six miles northeast of Portage Lake. The Allouez conglomerate, with a dip of 38" 15' and a general course of about 36' east of north, is overlaid by a trap, and has as its footwall an amygdaloid. The trap is followed by a series of amygdaloidal melaphyres and true amygdaloids, further on by the greenstone and ashbed; towards the lake shore alternating traps and conglomerates are found. At the footwall of the Allouez conglomerate, an amygdaloid lies, the thickness of which is not known, which is also the case with the other formations, accurate surveys and geologiwl researches of this district having, as I was informed, never been made. About 198 meters (650 feet), horizontally measured, from the Allouez conglomerate another amygdaloid bed can be traced, on which the present rockhouse stands, further on a melaphyre is exposed, and then follow the diverse conglomerates, the Calumet, the Kearsarge, and Kingston, which, according to the last geological report, are at about the re-

10th COMMONWEALTH MINING AND METALLURGICAL CONGRESS-CANADA, 1974 The Commonwealth Council of Mining and Metallurgical Institutions has received and accepted an invitation from The Canadian Institute of Mining and Metallurgy for the 10th Commonwealth Mining and Metallurgical Congress to be convened in Canada in April, 1974, immediately following the Annual General Meeting of The Canadian Institute of Mining and Metallurgy. It is proposed that the Congress centre will be Montreal and that, after technical sessions, tours of operations will be arranged. Further information will be issued in due course by The Canadian Institute of Mining and Metallurgy and enquiries should be addressed to the Executive Director of the Institute, 906-1117 Ste. Catherine Street West, Montreal 110, P. Quebec. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

The May General Meeting of the Institute was held in Kelvin House, Johannesburg, on 21st May, 1969, at 4.30 p.m. Mr J. K. E. Douglas (Vice-President) was in the Chair. There were also present twenty-two Members, including Messrs F. P. Bath, M. Bareza, A. R. C. Fowler, D. M. Jamieson, C. M. Mavrocordatos, D. G. Maxwell and J. A. Nixon (Council Members), Messrs T. Davidson, G. L. Diering, E. T. Dunstan, D. E. H. French, K. Hodgson, O. A. E. Jackson, A. F. Lee, A. Louw, D. L. Starkey, R. K. Wheeler and M. Youngworth. Four Associate Members including Messrs D. Blair Hook and G. R. Still. One Student Mr N. A. Barcza. Thirteen Visitors, including Messrs S. H. Ash, D. L. G. Bayne, E. Bayne, S. Bell, W. S. Garrett, L. S. Gibbs, R. C. Hamilton, M. Maguire, D. Rose and J. D. van Niekerk. Total Present: Fourty-one. OBITUARY The Vice-President: "It is my sad duty to announce the death of the following member of the Institute: Thomas Spence Haldane, Member, who joined the Institute in 1924 and passed away on 21st December, 1968. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, those present stood and observed silence for a few moments. MINUTES The Vice-President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. He also requested that confirmation of the minutes of the 75th Anniversary Meeting be held over. MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the under-mentioned candidates have been published in accordance with By-Law 5.2.2, and Council has elected them to membership of the Institute in the following grades: Members: Gideon Jacob Haumann, Peter John Cumming, Ian Stanley Dudman, Roderick Goldston Murchison. Associate Members: Francois Alwyn Beyers Fouche, Alan Marsh, Johannes Petrus van der Westhuysen, Waldo Edmund Stumpf, Ian Nicholas Ridley. Affiliates: Lutgerus Kolver Jooste, Roger Ainsley Ralph Kebble, Edward John Wainwright, Lewis William Davies. Graduate: Clive Graham Knobbs. MEMBER TRANSFERED TO A HIGHER GRADE From Student to Associate Member: Diethard Otto Eduard Fahrbach. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause).

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

It was determined that a selection of different types of fire sensors could be used to discriminate mine fires from nuisance emissions produced by diesel equipment. A neural network (NN) was developed for application to coal, wood, and conveyor belt fires in the presence of diesel emissions and evaluated with the successful prediction of twenty-two out of twenty-three mine fires based upon a fire probability determination. The optimum sensor selection for the NN was comprised of a carbon monoxide (CO) sensor, two different types of metal oxide semiconductor (MOS) sensors, and an optical path smoke sensor.

By Luana Karvel, Lars Kullerud, Morten Sørensen, Øystein Halvorsen, Øivind Lønne, Elaine Baker, Tina Schoolmeester, Joan Fabres, Yannick Beaudoin

The UNEP Shelf Programme (USP) is the access point for a collaboration of international organizations with expertise in marine geoscience and maritime law. It was established in response to a United Nations resolution, stating that the United Nations Environment Programme (UNEP), working through the Global Resource Information Database (GRID) system, should work in conjunction with Intergovernmental Oceanographic Commission of UNESCO (IOC) and the International Hydrographic Organization, to assist coastal States, and in particular developing States and small island developing States (SIDS) with submissions to establish the outer limits of their continental shelf under Article 76 of the United Nations Convention on the Law of the Sea (UNCLOS).

By A. Lubinski

In drilling operations, attention generally is given to hole angles rather than to changes of angle, in spite of the fact that the latter are responsible for drilling and production troubles. The paper presents means for specifying maximum permissible changes of hole angle to insure a trouble-free hole, using a minimum amount of surveys. It is expected that the paper will result in a decrease of drilling costs, not only by avoiding troubles, but also by removing the fear of such troubles. SUMMARY, CONCLUSIONS AND RECOMMENDATIONS Excessive dog-legs result in such troubles as fatigue failures of drill pipe, fatigue failures of drill-collar connections, worn tool joints and drill pipe, key seats, grooved casing, etc. Most of these detrimental effects greatly increase with the amount of tension to which drill pipe is subjected in the dog-leg. Therefore, the closer a dog-leg is to the total anticipated depth, the greater becomes its acceptable severity. Very large collar-to-hole clearances will cause fatigue of drill-collar connections and shorten their life, even in very mild dog-legs. Another finding regarding fatiguing of collar connections in dog-legs is that rotating with the bit off bottom sometimes may be worse than drilling with the full weight of drill collars on the bit, mainly in highly inclined holes when the inclination decreases with depth in the dog-leg. Means are given for specifying maximum dog-legs compatible with trouble-free holes. An inexpensive technique proposed is to take inclinometer or directional surveys far apart; then, if an excessive dog-leg is detected in some interval, intermediate close-spaced surveys are run in this interval. The application of the findings should result in a decrease of drilling costs, not only by avoiding troubles, but mainly by removing the fear of such troubles. The result would be much more frequent drilling with heavy weights on bit, regardless of hole deviation. Because of errors inherent to their use, presently available surveys are not very suitable for detecting dog-legs. There is a need for instruments especially adapted to dog-leg surveys. Crooked hole drilling rules should fall into two distinct categories—(1) those whose purpose is to bottom the hole as desired, and (2) those whose purpose is to insure a trouble-free hole. Three kinds of first-category rules in usage today are as follows. 1. A means to bottom the hole as desired is to prevent the bottom of the hole from being horizontally too far from the surface location; this may be achieved by keeping the hole inclination below some maximum permissible value such as, for instance, 5. 2. Another means to achieve the same goal is to limit the rate at which the inclination is allowed to increase with depth. A frequently used rate is 1/1,000 ft. In other words, a maximum deviation of l° is allowed at 1,000 ft, 2 at 2,000 ft, 3 at 3,000 ft, etc. 3. Whenever application of the first two means precludes carrying the full weight on bit required for most economical drilling, then the best course is to take advantage of the natural tendency of the hole to drift updip, displace the surface location accordingly and impose a target area within which the hole should be bottomed. This method has already been successfully applied,'.' and its usage probably will become more frequent in the future. Means for calculating the amount of necessary surface location displacement are avail-able.3'5'6 If in high-dip formations the full weight on bit should result in unreasonably great deviations, the situation could be remedied by increasing the size of collars and (if needed) the size of both hole and collars,351 or in some cases by using several stabilizers. Rules which would fall into the second category (i.e., rules whose purpose is to insure a trouble-free hole) are seldom specified today. It is vaguely believed that following Rules 1 and 2 of the first category will automatically prevent troubles. Actually, this is not true. If at some depth the only specified rule is that the hole inclination must be less than 4", the hole may be lost if the deviation suddenly drops from 4 to 2, or if the direction of the drift changes, etc. Rule 3 of the first category is generally used in conjunction with a rule belonging to the second category, namely, that the hole curvature' (dog-leg severity) must not exceed the arbitrarily chosen value of 1½ /100 ft. Moreover, when using this rule, the industry is not clear over what depth intervals the hole curvature should be measured. All this results in a frequent fear

By P. J. Nel, A. Täuber

SYNOPSIS A method is described whereby finely ground glassy granulated blastfurnace slag mixed with small quantities of clay, whiting and quartz has been used for making ceramic tiles in the laboratory. The tiles were semi-dry pressed and devitrification as well as sintering occurred during firing. The properties of the resulting product compared favourably in many respects with ordinary ceramic flooring materials.

By Hemang Desai

A damaged outlet pipe beneath Lenihan Dam has restricted reservoir discharges, severely constraining the owner?s groundwater recharge program. The solution, a new outlet pipeline through the dam?s right abutment, includes an approximately12.2-m-deep (40-ft-deep) shaft and 618.7-m-long, 4.3-m-diameter (2,030-ft long, 14-ft-diameter) tunnel mined in Franciscan melange composed of hard blocks of rock and soft clayey matrix. Alternating road header with drill and blast operations and using steel ribs and shotcrete have proven a flexible combination for handling the variable ground conditions. Excavating the shaft and connecting it to the tunnel require lowering the reservoir for five months, during which time careful construction sequencing and use of a tunnel plug eliminate the risk of an uncontrolled discharge.

By Dominic Orf, Gregory Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction. We were also able to observe the dissipation of the vibrations from the earthquake and see if the low frequencies, that are typical of earthquakes, dissipate at a consistent rate. Regression calculations were performed in order to see if there was a good data fit and if a specific vibration prediction could be made based on the magnitude of an earthquake. “How does quarry/mining/construction blasting compare to the Richter Scale?” This is a very common question that we get from homeowners when discussing vibrations due to blasting activities. This paper is intended to provide some simple answers for such a complicated question. Both the Richter and Mercalli scales are compared to the particle velocities as they were recorded from this earthquake.

By D. D. Howat

In the field of high temperature smelting processes there have been two dramatic changes in the past twenty years. These are, first, the application of tonnage oxygen for direct injection for the refining of molten iron and other metals and to provide the means of enriching air used for the combustion of fuel. Second, the application of electric power for the generation of high temperatures in place of the combustion of fossil fuels. Of these two developments the application of tonnage oxygen for the refining of molten iron has virtually revolutionised the steel industry throughout the world. The magnitude of this development is exemplified by the fact that less than 5 per cent of the world's steel production in 1960 was made by this process or 16 million tons out of a total of 350 million tons of steel produced, while in 1970 over 40 per cent of the world steel production was made by this process, ie, 251 million tons out of 628 million tons total. In the same period the proportion of steel produced by the old-established open-hearth process has shrunk from 75 per cent to 38 per cent. In the whole history of the development of high temperature metallurgical smelting processes there has never been anything remotely approaching this. The other development, the application of electric power for the generation of high temperatures has not had the impact of the oxygen injection process but I believe that what we should call the electric smelting revolution in metallurgical processes has very far-reaching ramifications for steel production and other pyrometallurgical processes. This may seem a bold and brash statement but it must be remembered that the oxygen injection process constitutes a link in the chain critically dependent upon the production of vast tonnages of molten iron from very large modern blast furnaces. The Achilles heel of this chain of processes, upon which such a large percentage of the world's supply of steel depends, is the availability of metallurgical coke in turn dependent on natural resources of coking coal. Without any exception each industrial country in the world faces a shortage of resources of coking coal and in some cases a critical shortage. Certainly within the present century the major iron and steel producing countries of the world will face this critical shortage of coking coal and major modifications to steel making processes will become inevitable. W. F. Cartwright (Deputy Chairman of B.S.C) said recently that there are considerable doubts as to whether the world will be able to provide enough coking coal to meet world steel demands from the late 1970's onwards if the B.F.remains the main means for making iron from ore. This is one of the supreme ironies of the world metallurgical situation to-day when the technology of iron and steel production has reached an extremely high peak of technical efficiency. The newest modern iron blast furnace capable of producing 6 000 to 8 000 tons per day of molten iron represents probably the most efficient piece of high temperature metallurgical plant and operation known to man. The conversion of this molten iron into steel by the oxygen injection process has made available to the engineering industry steel of a quality and at a price which is quite remarkable. Yet this vast metallurgical pyramid rests on the completely insecure and uncertain foundation of inadequate world resources of coking coal. The shortage of reserves of coking coal in this country is acute and it is possible that these resources will be exhausted within the next twenty years. Yet unless some completely unexpected catastrophe occurs the demand for steel in this country will probably rise at a faster rate than in the Western world due to the expansion of the Bantu population and the increased standard of living. To offset the inevitable shortage of coking coal are our much greater resources of bituminous coal which although of low grade provide a suitable fuel for electric power generation. The geographical disposition of the coal fields in relation to the great industrial areas of the Transvaal makes it inevitable that the development of the pyrometallurgical industries must depend heavily on electric power. The position in this country with regard to electrical power generation and consumption is rather anomalous. Per capita consumption of electric power is high - in 1964 almost twice the world average of 870 KWH and twenty-five times the average of 34 KWH for the Continent of Africa. In 1964 fifty-four per cent of the total world electric power was used in industry - the ratio being approximately 1/9 mining to manufacturing uses. As shown in Table I in 1969 67.2 per cent of the total output of electric power from ESCOM was used for mining and other industrial uses but almost in the ratio 6/4 mining to industrial uses. These figures emphasise the enormous importance of the mining industry to the economy of this country and underline the major contribution made by the gold mining industry. What is of very significant importance is that although the mining industry remains by far the largest single consumer of electrical power the consumption of power for industrial uses is rising rapidly as shown in Table II.

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Peter L. Swanson

NIOSH has developed an automated PC-based seismic monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network (LAN) is a central feature of the system. Design requirements include (1) the use of lowcost, off-the-shelf, data acquisition and computer hardware, (2) the capability of automatically merging waveform data sets from different types of monitoring systems, (3) delivery of raw and processed data underground and on the surface, as well as to remote sites, and (4) automated data collection and processing over long periods of time without the need for human intervention. Current mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface and provide 20 to 40 stations within a radius of several kilometers. Event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's hardware and software components, examples of installations in hard-rock and coal mines, and a few observations from western U.S. longwall coal mines.

By Bill M. Stewart, Philip W. Patton, Curtis C. Clark

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines we revisited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.