Search Documents

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By Y. Mishima, R. Shiromizu

THE equilibrium y phase in Cu-Be alloys forms by discontinuous precipitation, the new phase nucleating at the grain boundaries and growing into grains on both sides of the boundary. When the alloy is aged above 500°C, however, growth may take place into only one of the grains.1'2 In A1-Ag alloys it is known that the precipitate has the same orientation as the grain in which no growth takes place.3, 4 This was confirmed in the present investigation on a Cu-Be alloy. A Cu-1.79 wt pct Be alloy was solution-treated at 810°C for 2+ hr, quenched into water at O°C, and aged at 600°C for 1 hr in a salt bath. The specimen was thinned by chemical polishing and electropolishing at room temperature in a solution of H3PO4 saturated with CrOs. The foil produced was examined in a JEM 150 electron microscope operating at 150 kv. Fig. 1 shows precipitates growing on only one side of the grain boundary. The black platelike precipitates were identified as the y phase. Electron dif-

Jan 1, 1969

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytic expressions were developed and applied in two preuious papers to predict effects of solidification variables on macrosegvegation. In this paper, experiments are reported to test the analyses quantitatively and qualitatively. Good quantitative agreement is obtained between predicted and measured compositions for the following types of segregation (all experiments were on laboratory-size ingots of Al-4.5 pct Cu alloy): (a) inuerse segregation, (b) composition distribution in ingots solidified with unidirectional heat and fluid flow, (c) simulated centerline segregation, and (d) segregation resulting fro, change in solidification cross section. In addition, qualitative agreement of prediction of theory with experiment is obtained for (a) segregation resulting from sudden change in heat extraction during solidification, (b) centerline segregation in a bidirectionally solidified ingot, and (c) under-riser positive segregation. IN two previous papers,''2 it was shown that a variety of apparently different types of macrosegregation result from the same basic mechanism. This mechanism is the flow of solute -rich liquid to feed solidification and thermal contractions. Analytic expressions were derived and examples given of their application to predict macrosegregation. Calculations were for Al-4.5 pct Cu alloy. In this paper, we describe a series of experiments designed to test results of the foregoing calculations. All experiments were on laboratory-size ingots (weighing 10 lb or less), of A1-4.5 pct Cu alloy, nominal composition. APPARATUS AND PROCEDURE A typical mold and chilling arrangement used for unidirectional solidification is shown in Fig. 1. Before casting, this assembly was placed in an electrically heated air furnace, and heated to 680" to 700°C. When the plaster reached the desired temperature (usually 1 to 2 hr after the furnace temperature), the mold was filled through a funnel extending from the outside of the furnace into the cavity. The assembly, with liquid, was held for several minutes to allow convection to subside. The coolant, either air or water (depending on the desired solidification rate), was turned on and the ingot solidified. With the four sides and top insulated, heat removal for solidification was through the bottom surface, resulting in a fully columnar structure. Design of the casting cavity was varied, as discussed below, to produce desired macrosegregation effects. However, for castings solidified with unidirectional heat flow, the top was always open to the furnace atmosphere and temperature. The bottom sur- face rested on a chill through which the heat was extracted, and all other surfaces were insulated with plaster. In one case to be discussed, the mold design was changed to obtain bidirectional solidification. In this case, two vertical chills were used (on two faces of the mold) and the bottom was insulated. In a last case discussed, that dealing with under-riser segregation, experiments were conducted in bottom-chilled sand molds at ambient temperature. Except for this one case, all experiments were conducted in the electrically heated air furnace as described above. In many ingots, thermocouples were used to obtain continuous records of solidification. In all cases, these were chromel-alumel couples with output continuously monitored on a twelve-channel recorder. Where thermocouples were employed, these were embedded in the refractory mold walls during mold-making so their heads extended to the vertical centerline. Six to nine couples were employed, placed at intervals from the chill. METAL-MEL TING PROCEDURE Aim analysis was A1-4.5 pct Cu; alloy was prepared from high-purity aluminum (99.9 pct Al) and A1-Cu master alloy (50 pctOFHC Copper, 50 pct high-purity Al). The A1-4.5 pct Cu alloy was cast in 5- to 7-lb ingots for subsequent remelting for the macrosegregation experiments. Melting for ingot casting was as follows. After preheating the melting crucible for an hour or more, the charge was melted and superheated to a temperature of 690" to 720°C. After stirring, the melt was degassed with chlorine for 10 min. After stirring again for 1 min, a gas sample, under reduced pressure, was taken. When the sample was gas-free, the crucible

Jan 1, 1969

By P. M. Kelly, E. P. Butler

The stability of a 70/30 Mn-Cu alloy aged to peak damping has been investigated using electron microscopy, X-ray diffraction, and torsional pendulum measurements. Storage at room temperature or at 100" C causes a reduction in damping capacity. This is shown to be due to the formation of subdomains which "lock" the main domain structure and so hinder their movement. After storage the damping capacity can be restored by a retransformation treatment, which generates structures identical to those found in newly aged specimens. Plastic deformation by rolling also causes a decrease in damping capacity. In this case the damping capacity can only be restored by retransformation if the amount of deformation is less than about 5 pct. THE general metallography and structure of these high damping capacity alloys has been discussed in Part I of this work.1 Part II deals with some of the variables that affect the damping capacity. In particular, the stability of the damping capacity of a 70/30 alloy aged for 2 hr at 425° C and quenched has been investigated. The temperature sensitivity of the damping capacity of a 70/30 alloy aged for 2 hr at 450° C has been reported by Birchon.2 The damping capacity begins to decrease with increasing temperature, and is very low above the M, temperature of 125°C. The cubic — tetragonal transformation is completely reversible and there is no apparent thermal hysteresis associated with the change in damping capacity. Another important effect was first reported by Dean and his coworkers.3 They noticed a decrease in the damping capacity with time for specimens of a quenched tetragonal alloy. More recently workers at the Admiralty Materials Laboratory 4 have studied the stability of an aged 70/30 alloy. They found that the damping capacity decreased to half its original value after about 1000 hr at room temperature. EXPERIMENTAL The techniques used for electron microscopy and X-ray diffraction have been described in Part I. The damping capacity was measured by means of a torsional pendulum, using rectangular specimens, 3 by 0.3 mm with a 6 cm gage length. The specific damping capacity, S.D.C., was calculated as a percent amplitude decay in free vibrations over 10 cycles, starting at an amplitude which corresponded to a 700 psi surface shear stress. Because of the stress dependence of the damping,' the values obtained were about a third those reported for a 5000 psi surface shear stress.' RESULTS a) Effect of Aging Temperature. The effect of aging temperature on the damping capacity is shown in Fig. 1. The damping capacity reaches a peak of 12 pct after aging at 400° to 425°C) then begins to decrease as the volume fraction of a Mn increases. At higher aging temperatures the structure becomes cubic again with a low damping capacity. b) Stability of the Aged Structure. The damping capacity of the aged alloy decreases with time at room temperature. This process could be accelerated by storing at 100°C, when about 100 hr were required for the damping to fall to half its original value. The results of room temperature and 100°C storage, for times up to 1000 hr, are shown in Fig. 2. The damping capacity starts to decrease after about 24 hr at 18° C and 1 to 2 hr at 100°C. It was found, however, that the damping could be almost completely restored by retransformation. The specimens were held at a temperature above the M, for a short time, 250° C for 5 min, and then quenched. The values of damping capacity for specimens that were aged, stored, and then retransformed are shown by the full points in Fig. 2. X-ray measurements of the c/a ratio and hardness readings on the specimens did

Jan 1, 1969

By R. E. Goodman, M. A. Mahtab

The, state of stress around a vertical wellbore in rock following nonlinear stress-strain laws is examined by means of finite element analysis. The wellbore, is considered an axisymmetrier body with axisymmetric loading. The initial vertcal and borizontal stresses are "locked" in the rock elements around the wellbore and a new state of stress is generated by the displacements which occur around the borehole. A point-uise variation of the elastic moduli is made on the basis of the new stress state and the triaxial data. The initial stresses tire now reintroduced along with tile changed moduli and original boundary constraints. This procedure is repeatrd until convergent stresses are reached. The effect of nonlinearity on streases is examined for a 6,000-ft wellbore in a scbistose gnezss and Berea sandstone using results of laborratory triaxial compression tests. The results sbou that the effect is restrited to one well radius from the bottom periphery of the bole. Beyond a distance of one-quarter radius, the elfect of nonlinearity on stresscs IS almost always less than percent for the cases conszdered, The consideration of a static pressure inside the well does not magnify the effect of monlinearity on borehole stresscs. INTRODUCTION The terms " wellbore" and "borehole" here designate cylindrical openings in the ground with vertical axis and a circular cross-section. A knowledge of the stress redistribution that occurs on excavating a wellbore is important in understanding (1) the behavior of the lined or unlined hole, (2) hydraulic fracture response, and (3) the effect of stress redistribution on drillability; also it is important in predicting initial stresses in the virgin ground, and in analyzing the response of measuring instruments placed in the borehole. Our knowledge of the state of stress around a wellbore has been restricted to homogeneous, isotropic, elastic material and derives chiefly from the analysis by Miles and Toppingl and the photoelastic work of Galle and Wilhoit2 and Word and Wilhoit.3 In this investigation the state of stress is examined for a nonlinear elastic material by means of finite element analysis. Many rocks possess stress-strain curves that depart notably from straight lines in their initial or final portions. While the literature contains abundant stress-strain data from triaxial tests (axisymmetric loading) on cylindrical rock specimens, there is little information on rock deformability under nonaxisymmetric loading conditions such as occur at each point around the bottom of a wellbore. Although there is some knowledge of the effect of intermediate principal stress on rock strength, there is virtually nothing known about its effect on rock deformability; therefore, we have assumed here that the effect of intermediate principal stress can be ignored. A schistose gneiss4 and Berea sandstone5 were selected as representative rocks for this analysis. The traditional graphs of deviator stress (ol -o3) vs axial strain were reworked to give the tangent modulus as a function of the deviator stress for varying values of the minor principal stress. The result is a nesting family of skewed, bell-shaped curves for tile gneiss (Fig. 1A) and the sandstone (Fig. 2A). A similar replotting of the lateral strain data defines the variation of Poisson's ratio (v) with the deviator stress and confining pressure. These curves, shown in Fig. 1B for the gneiss and in Fig. 2B for the sandstone, are not so well ordered as the tangent modulus curves. However, all of these display an increase of v with deviator stress application, but the rate of increase diminishes with confinement. The ET and v curves for the two rock types are tabulated in Tables 1A and 1A for use in a digital computer so that material properties corresponding to a given state of stress can be assigned by interpolation. STATEMENT OF THE PROBLEM Given a state of stress in the ground prior to drilling a hole (initial stresses), we assume that

Jan 1, 1969

By H. J. Ramey, I. S. Bousaid

Experimental results on the oxidation reaction kinetics in the forward combustion oil recovery process are presented. A total of 48 runs were made wherein a stationary thin layer of coked, unconsoli-dated sand was burned isothermally in a combustion cell. Individual runs were made at various temperature levels to permit determination of the effect of temperature upon the reaction. An expression was obtained for the burning rate of carbon as a function of carbon concentration, combustion temperature and oxygen partial pressure. The carbon burning rate for two types of crude oil indicated a first order reaction with respect to both carbon concentration and oxygen partial pressure. The effect of combustion temperature on the reaction rate constant matched the Arrhenius equation. The activation energy was similar for the two crude oils examined. The activation energy decreased for a porous media containing clay. The rate of oxidation of crude oil at reservoir temperature was found to be significant. Other significant findings included information on hydrogen-carbon content of fuel residues, fuel reactivity and the products of combustion. INTRODUCTION The production of crude oil by underground combustion has been studied in the laboratory by many investigators.1-5 Results of laboratory and field experiments have been reported in the literature describing the forward combustion process. But as yet, no qualitative or quantitative study of the kinetics of fuel combustion involved in this process has been reported. The fuel concentration and the rate at which fuel is burned at the front are important factors governing the air requirement in a forward combustion operation. Although the fuel is essentially unrecoverable crude, the air required to burn the fuel is an important economic factor in this process. Because fuel is burned, the heat transport associated with forward combustion is a key and unique feature of this new oil recovery method. Many investiga-tors5-9 have presented information on the heat transmission and fluid mechanics involved in forward combustion. Berry and Parrish10 demonstrated the utility of considering reaction kinetics in reverse burning. From differential thermal analysis, Tadema11 presented a qualitative discussion of the nature of reactions between oil and oxygen in combustion oil recovery. Although little quantitative work has been done on the reaction kinetics involved in forward combustion oil recovery, an extensive literature does exist on combustion of carbons and oils, and carbonaceous residues from cracking catalyst pellets. Dart, et al., 12 studied the combustion rate for oxidation of carbonaceous residues on clay catalyst pellets, and found the reaction to be second-order with respect to carbon concentration, and first-order with respect to oxygen partial pressure for carbon concentrations less than 2 weight percent of the catalyst weight. The reaction appeared to be first-order with respect to carbon concentration for concentrations greater than 2 percent. Metcalfe13 noted that other workers had found that aging of the fuel during the combustion process was responsible for changing coke properties, and it accounted for the apparent second-order carbon concentration effect found by Dart, et al. It appears that burning of residues from cracking pellets is first-order with respect to both carbon concentration and oxygen partial pressure. Dart, et al., also observed that hydrogen in the hydrocarbon residue appeared to react faster than the carbon. Lewis, et al.,14 studied oxidation of charcoal, coke and graphite in a fluidized bed. Gas velocities were high enough to partially lift and circulate the carbon particles. Their results indicated first-order reaction dependency with respect to both carbon concentration and oxygen partial pressure. One

Jan 1, 1969

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

By Reino Kurppa

The Pyhäsalmi mine of the Outokumpu Co. is located in central Finland (Fig. 1). The deposit was discovered in the autumn of 1958. Construction of the mine was started a year later, and production began on Mar. 1, 1962 (Fig. 2). At present, 750,000 metric tons (mt) of ore and a nearly equal amount of country rock are mined annually. Slightly over one-half million tons of various concentrates are produced per year, of which 85% is pyrite concentrate, 10% zinc concentrate, and 5% copper concentrate. The pyrite concentrate is treated in the company's pyrite smelter,1 yielding elementary sulfur, sulfur dioxide, and iron-oxide cinders, as well as electric power. Thus all the sulfides, totaling 75% of the ore, are of economic value. This is a fact which had a bearing on the development of the stoping method. GEOLOGY The ore is of breccia type containing fragments of country rock of varying sizes. It is coarse-grained pyrite ore containing sphalerite and chalcopyrite as a matrix between the pyrite grains. Only small amounts of pyrrhotite have been observed in certain marginal parts of the orebody. The ore averages 0.85% Cu, 3.0% Zn, 38% S, and 33% Fe. The orebody extends from the surface down to at least 500 m, which is the lowest level from which present information has been obtained. Horizontally, the orebody is 650 m long. It is 75 m wide at its central part, narrowing towards the ends (Fig. 3). At a depth of 115 m, the orebody suddenly narrows down to a thickness of 25 to 30 m. In the northern part of the orebody, the dip is 50° to 70°, but elsewhere it is almost vertical (Fig. 3).

Jan 1, 1969

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and*pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anortho- site layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spinel-bearing meta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the Goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, Ni, etc. liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

The liquid products of low-temperature carbonisation of coal are of variable composition, very much influenced by the rank and type of coal, and process parameters. In general the tar contains a high proportion of phenols and a low proportion of bases. The neutral oil is more analogous to a thermally cracked petroleum oil than to a high temperature tar. Present practice and possible future trends in the production of chemicals and liquid fuels from low temperature tar are reviewed in the light of recent work on the detailed composition of the tar The phenols and aromatics will probably continue to be of most value, with the bases a useful source of spec- ialty products. However the high aliphatic content of the neutral oil (particularly 1-olefins and n-paraffins) is bound to receive more attention for chemicals as well as for liquid Fuels.

Jan 1, 1969

To provide suitable backfill material for the cut and fill mining method being used to extract ore from the C.S.A. mine, flotation tailings are deslimed in single stage cyclones. The sand fraction is stored on the surface in unagitated storage bins before being pumped underground, while the slime portion is thickened and pumped to a residue dam. Design and operating details of the sand preparation and storage sections are given.The initial preparation of a stope for filling, consists of laying percolation and decantation drainage pipes on the sill floor. Preparation for fllling of subsequent lifts consists of rearing up the ventilation pipes at the ends of the stope, preparing the decantation system, and building a barricade or wall. The fill is carried to, and discharged into, the stope through 4 in. diameter pipes and filling of any section is carried out 24 hr/day normally without supervision. The fill is retieulated underground to the 1200 ft level through rubber lined pipe installed in the upcast shaft. Boreholes of 3 in. diameter drilled from the1200 ft level convey fill to the 1800 ft level. The mine drainage system is basically designed to handle the water associated with hydraulic filling. A system of primary and secondary sumps has been installed to handle the percolation and decantation drainage from stapes and to allow settling of fines before the water is fed to the main pump station.A programme of investigation into the properties of the emplaced fill is in progress. Results to date indicate that the fill as presently placed and drained, will not cause any problems in the mining of vertical orebodies by cut and fill methods for lifts in excess of 300 ft.

Jan 1, 1969

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By G. C. Laurence

"This paper discusses the hazards and extensive precautions taken in Canadian uranium mines, concentrating plants and processing plants. It also outlines Canadian policy regarding the control of the sale and distribution of uranium and other nuclear materials.OVER THIRTY YEARS AGO, I spoke to The Canadian Institute of Mining and Metallurgy here in Montreal about radioactivity and its dangers. I must have made quite an impression thirty odd years ago, because now you have asked me to do it again. Of course, the picture has changed. Then they were mining uranium ore, recovering the radium from it and throwing away the uranium. Now they are still mining uranium ore, but are throwing the radium out on the tailings dumps. Thirty years ago, most people did not know what ""radioactivity"" meant. Nowadays, they have beard that it is dangerous, and some of them, recently, be-came worried about the radium in the tailings dumps and what becomes of it."

Jan 1, 1969

By S. G. Epstein

Electromigration has been measured in dilute liquid alloys of lead in antimony and antimony in lead. In these alloys antimony migrates with the electron current; lead migrates in the opposite direction. These results, which contradict the mass criterion, were predicted by the electron drag model for electromigration in liquid alloys. The existing experimental data are shown to correlate with the difference in electrical resistivities of the alloy components. FOR many years investigators have attempted to relate observed electromigration phenomena in liquid alloys to the physical properties of the alloy components. The most successful correlation was found by Angus et' al.,1 who in 1959 proposed an empirical criterion for predicting the relative direction of motion of the components of a liquid alloy in an electric field: the component with the smallest atomic mass concentrates at the cathode. While this criterion is obeyed in nearly all the alloy systems which had been investigated, the physical basis for such an effect was not understood. It was also disturbing that the mass criterion predicted the wrong sign for the Haeffner effect; observations with pure liquid metals revealed that in every instance the lighter isotope was transported to the anode.2 Klemm3 explained these isotopic separations by suggesting that the lighter isotopes were more mobile and more easily carried to the anode with the electron stream. Additionally, several deviations from the mass criterion have been found in liquid alloys, notably involving transition metals such as chromium, nickel, palladium, and zirconium, which migrate to the anode in liquid bismuth.4'5 Recently, a model has been proposed6 in which electromigration in liquid alloys is attributed primarily to the interaction between the electron stream and the metal ions. In essence, this model predicts that the component with the greater electron-ion scattering cross section will be preferentially transported to the anode, displacing the other component to the cathode. The electrical resistivity of each pure component at its melting point is taken as the measure of its scattering cross section. This model was developed from the results of systematic studies with various solutes in liquid mercury,7'8 bismuth,9 and sodium.10 In every alloy, the component with the greater resistivity has centrates at the anode. Coincidentally, in every instance the component with the greater resistivity has also the greater mass, apparently satisfying the mass criterion. In order to differentiate between electron-ion coupling and atomic mass as the relevant physical prop- erty influencing electromigration, measurements were made with Pb-Sb alloys. Lead has an atomic mass nearly twice that of antimony, but lead has an electrical resistivity of 91 microhm-cm while antimony has a value of 113.5 microhm-cm at their respective melting points. The mass criterion predicts that in an alloy of the two antimony will concentrate at the cathode; the electron drag model predicts that antimony will concentrate at the anode. EXPERIMENTAL To conclusively determine the relative motion of lead and antimony in each other, solute electromigration was measured in dilute liquid alloys of antimony in lead and lead in antimony. Both starting materials were 99.999+ pct pure. The measurements were made with the same capillary-reservoir technique previously used for measuring electromigration in liquid bismuth alloys.11 Several changes in the experimental apparatus were necessary, however, to accommodate liquid antimony, which has a higher melting point than bismuth. The modified apparatus is depicted in Fig. 1. In each experiment four quartz capillaries were filled with the molten alloy. A direct current was passed through two of the capillaries; the electrode in one of these capillaries was made the cathode, and the electrode in the other was made the anode. The remaining two capillaries sampled the alloy in the reser-

Jan 1, 1969

By E. T. Turkdogan, L. S. Darken

Using the quadratic formalism, thermodynamic equations are derived for the composition dependence of the heat and entropy of mixing. The applicability of these equations is confirmed by available experimental data on the activities and heats of mixing for binary metallic systems of Group ZZB elements. In a recent paper arkeen' introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. That is, in the terminal region, which may extend to as much as 60 at. pct, the logarithm of the activity coefficient, log y,, of component 2 is a linear function of (1 - N,)' where N2 is the atom fraction of component 2. Similarly, for the other component, log yl is a linear function of (1 - N,)'. A number of iron-base binary liquid alloys were shown to obey this quadratic formalism. arkeen' extended this formalism also to any corner of a ternary system and showed that the activity coefficients of the components 1, 2 and 3 (1 is taken as the solvent) can be represented by quadratic terms involving five parameters, four of the binaries and one for the ternary system. Numerous examples given by arkeen' demonstrated the general applicability of the quadratic formalism to iron-base systems over a wide composition range. In this paper further examples are given of binary liquid systems (Group IIB elements, Zn, Cd, and Hg) and of several solid solutions, again demonstrating the appropriateness of this concept. A further purpose of this paper is to extend the quadratic formalism to the enthalpy and excess entropy of binary metallic solutions and to test the equations so found using available experimental data. QUADRATIC FORMALISM FOR HEATS AND ENTROPIES OF MIXING OF BINARY METALLIC SOLUTIONS The following equations, reproduced from Darken's paper, are for the two terminal regions of binary systems. at infinite dilution and a's are temperature dependent parameters to be determined from the experimental data. Although the quadratic formalism is an assumed representation of the data, Eqs. [I] to [4] are thermo-dynamically consistent with the Gibbs-Duhem relation and satisfy Raoult's and Henry's laws as limiting cases. As pointed out previously,' the following form of the Gibbs-Duhem equation facilitates the integration in general but particularly in regions I and 11, where each of the derivatives is constant. The partial molar enthalpy of solution i, (and i; the value of i, at infinite dilution) are related to the activity coefficients y, and y," by the thermodynamic relation Differentiating Eq. [l ] with respect to 1/T and substituting the above thermodynamic relation gives for region (I) It is reasonable to assume that over a temperature range of experimental interest, the enthalpy of mixing is essentially independent of temperature, implying from Eq. [7] that the derivative da,,/d(l/) is also independent of temperature. On the basis of this argument, the temperature dependence of a has the form where £ and S have the units of enthalpy and entropy respectively; they are characteristic parameters for a terminal region of a binary system, e.g. for region (I), C12, S12 and for region (II), d:,,, S2,. Using this equation gives for dff ,/ d(l/), From Eqs. [7] and [9] an expre_ssion is obtained for the composition dependence of L,. Similar calculations are made for El and the results are summarized below for the two terminal regions. For region (I), The corresponding expressions for the molar heat of solution, AHM, are readily obtained from the above equations for the two terminal regions: For region (I),

Jan 1, 1969

By Daniel T. O’Brian

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented in this paper.

Jan 1, 1969

By Ivan Simon, R. K. McConnell

Anticipating the availability of tiltmeters suitable for use in boreholes, this article proposes a method of using one or more of these meters to determine in situ stress distribution before and after mining operations. Several ways of using relief techniques to measure in situ stresses in rocks have been developed. These techniques, summarized by Merrill,1 involve measuring deformations which take place when a specimen of rock is wholly or partially isolated from the stress field in the surrounding rock. Measurements of rock deformation caused by stress relief from mining operations can, in principle, also be used to estimate in situ stress distributions. Müller2 has mentioned experiments being carried on in Austria with a "deformation indicator" to determine the tilting of holes drilled before a mine opening is made. Similar work using borehole extensometers has been reported by Potts? and Duvall4 has called attention to the possible use of tiltmeters in making these measurements. Considerable attention is now being paid to the use of tiltmeters in detecting rock deformation associated with fault movements, earthquakes, earth tides, etc. The instruments used for these measurements have usually been of the mercury tube, water tube, or quartz fiber type, but because of their large size, and/or fragile nature, such instruments would not be suitable for use in mining stress measurements. Recent instrumentation developments, however, give promise that rugged, sensitive tiltmeters small enough for use in boreholes may soon be available.' In anticipation of these developments, this article presents a number of calculations of the possibility of using one or more tiltmeters emplaced in a drill hole prior to mining operations to determine the in situ stress distribution both before and after a mining operation. Consider point p (x, z) near a tunnel of radius a

Jan 1, 1969

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969