Search Documents

By Forrest T. Moyer

The safety record of the metal mining and milling industries in 1965 is reviewed by the Bureau of Mines. The overall injury-frequency rate of 23.77 per million man-hours was 5 percent lower than in 1964 and was the lowest annual rate in a statistical history beginning with 1931. The injury-severity rate of 3,521 days lost per million man-hours in 1965 represented a 5-percent improvement over 1964. However, the total of 3,825 disabling work injuries comprised 61 fatal and 3,764 nonfatal injuries, one and 92 more, respectively, than in 1964. At primary nonferrous smelters, refineries, and reduction plants, the injury-frequency rate of 8.97 per million man-hours in 1965 was 13 percent lower, but the severity rate percent higher than in 1964. these plants in 1965, 4 more of 1,173 days lost per million man-hours was 17 There were 12 fatal and 971 nonfatal injuries at and 28 fewer, respectively, than in 1964.

Jan 1, 1969

By Verne E. Hooker

In situ stresses, based on isotropic and anisotropic relations, were evaluated using computer techniques from overcoring data obtained in dimension stone quarries along the Appalachian Piedmont, the Ozark Uplift, and the Ouachita Tectonic Belt. Stresses in the horizontal plane near the surface are compressive and range from 100 to 4,500 psi. The direction of maximum compressive stress seems to be alined with the general tectonic structure for most of the determinations. The ratio of the maximum to minimum elastic parameters in the horizontal plane ranges from 1.05 to 2.46 for these competent rocks. Isotropic versus anisotropic stress determinations show differences only as great as 25 percent in stress magnitude and 25° in orientation.

Jan 1, 1969

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By Wesley T. Holmes

In this final stage of a three-part investigation of the smelting of titania-bearing iron materials, the Bureau of Mines conducted semicontinuous smelting tests in a laboratory electric arc furnace on four concentrates and one are. The objective was to substantiate the significance of liquidus temperature measurements in predicting satisfactory slag compositions in electric furnace smelting of titaniferous magnetites to produce pig iron. Previously obtained liquidus temperature data were used in determining flux requirements. Self-fluxing pellets of either ore or concentrate plus fluxes and reductants were made to produce pig iron and slags containing 0.2 to 0.6 percent titanium. Individual constituents of the slags generally agreed within 5 percent with the value of the corresponding constituent of target composition. Liquidus temperature of furnace slags generally agreed within 50° C of the value obtained from corresponding nominal synthetic slag. The results of the three phases of the investigation may serve as guide-lines for determining flux requirements in smelting a wide variety of titaniferous magnetites and other titania and iron-bearing materials.

Jan 1, 1969

By S. K. Asunmaa, W. D. English, N. A. Tiner, W. A. Cannon

This paper discusses the reaction of metal surfaces with fluorine. Fluorination reactions result in the formation of metal fluoride films which are "passive" toward further reaction of the metal with fluorine. These films are very adherent, and do not easily detach from the substrate metal by mechanical flexing or thermal shock. Exposure of passive films to a humid atmosphere produces hydrated metal fluorides which cause secondary fluorination reactions upon reexpo-sure of the metal surface to fluorine. The surface films formed range from 10 to 30A in thickness and they pow at the expense of surface oxide films. The apparent film formation is completed rapidly in 15 to 30 min on stainless steel and nickel surfaces. On copper and on Monel surfaces, the film at first grows rapidly, then increases slowly over an extended period of time. Passive films are formed at all fluorine pressures in the range from 0.1 to 1.4 atm at room temperature. ALL metals react when exposed to fluorine. These reactions generally produce surface films which consist of metal fluorides. The rate of reaction is largely determined by the extent to which these films are protective. Although there is an extensive literature concerning reactions of oxygen with metals, there are very few investigations reported concerning fluorine-metal reactions. Brown, Crabtree, and ~uncan' investigated the kinetics of the reaction of gaseous fluorine with copper metal which had been freshly reduced in hydrogen. The reaction rate was independent of pressure over the range from 6 to 60 torr. A logarithmic rate law was obeyed in the temperature range from 25" to 300" ~. There was some deviation at higher temperatures which could have been the onset of a parabolic law. The calculated film thicknesses ranged from about two molecular layers, 10A, for 5 hr exposure at room temperature to thirty-five molecular layers for 5 hr exposure at 200" . The authors concluded that no single mechanism could explain all the observations. O7Donnell and spatkowski2 studied the reaction of fluorine with copper at 450°C at pressures from lo to 133 torr. The reaction was found to be pressure -dependent and followed a logarithmic rate law. It was not entirely diffusion-controlled, and fluorine was thought to be the migrating species in the reaction. Miscellaneous metal-fluorine reactions were investigated by Haendler et ~1.~ Reaction products were identified but no rate data were determined. Air Prod- ucts and Chemicals, Inc., have conducted an investigation of reactions between fluorine and various metal powders at room temperature and 85° C. Fluoride film thickness as a function of time of exposure was reported on the assumption that the reaction takes place between fluorine and metal to form the normal metal fluoride. Surface areas of the powders were only estimated so the relative film thicknesses may not be exact. The data showed reaction rates which were generally logarithmic in character, the rate of film growth virtually ceasing after a few hours exposure time for some alloy powders. The effect of moisture on fluoride films was also investigated by measuring additional reaction with fluorine after exposure of passivated powders to atmosperic moisture. The fluorination of iron was studied by 0'~onnell~ at temperatures from 225" to 525" ~ and at pressures ranging from 20 to 200 torr. In all ranges, the reaction followed a logarithmic rate law and was dependent on the square root of the gas pressure. The author concluded that fluorine gas passes through pores in the film. As the film grows, the blocking of pores leads to a rapid decrease in reaction rate; hence a logarithmic rate law is observed. Jarry, Fischer, and Gunther' investigated the mechanism of the reaction of fluorine with nickel at about 600" to 700°C. On the basis of the metallographic examination of fluoride scales growing on the nickel and from separate radioautographic data, it was claimed that fluorine is the migrating species in the reaction. This is in sharp contrast to the growth of oxide films on nickel where it has been shown that nickel ions migrate through the scale to the gas-solid interface to react with oxygen. Few investigations have been reported of the reaction of fluorine with metal oxides. Such investigations should be of great significance for a better understanding of passivation in view of the ubiquitous oxide films on technical alloys. Haendler et al.3 studied the reaction of fluorine with oxides of copper, tin, titanium, zirconium, and vanadium. Copper (I) oxide reacted as follows in the temperature range 150" to 300"~: temperature above 300" ~ was required for the CuO to react to form additional copper fluoride. Ritter and smith7 also investigated the reaction of fluorine with copper (11) oxide. An oxide powder comprised of spherical particles with a fairly high surface area was reacted with fluorine, starting at room temperature and increasing to 100° C over a period of 3 or 4 hr. The initial reaction was slow until the fluoride film thickness reached about to or 15R at which time the reaction rate accelerated, then decreased again. Most of the kinetic data was obtained during this final phase of reaction. The authors conclude that the film grows slowly at first until the stresses developed in the distorted lattice are sufficient to rupture the initial

Jan 1, 1969

By David L. Holt

The contribution of grain boundary shear to total elongation, CS/E&apos;, has been measured in an Al-Zn eu-tectoid alloy that was quenched from above the invariant temperature, then annealed at 250° C to a grain size of&apos; 1.8 p. At 250°C, ks/E&apos; is low at both high and low strain rates, but reaches a maximum, estimated as 60 pct at an intermediate rate of 5 X 10 per rnin. Rate sensitivity, as measured by the index m = a log a/a log E&apos;, follows the same trend, and furthermore the maximum values of m and -cur at approximately the same strain rate. This result, combined with the metallographic observation that boundary migration enhances boundary shearing, is interpreted as supporting a previous suggestion that the high rate sensitivity characterizing super-plasticity is the result of combined boundary shearing and migration. It is suggested that the latter event relieves stress concentrations at triple points, and smoothes boundaries so that stress is governed largely by a viscous boundary shear. GrAIN boundary shear has been considered in relation to superplasticity in several recent papers.&apos; The problem has been to explain the high strain rate sensitivity of flow stress, and the variation of rate sensitivity with strain rate (E&apos;) and grain size (L). The requirements for superplasticity, small L and high T, suggest the reasonableness of an approach to high rate sensitivity involving grain boundary shear. Further support came from experiments on the A1-Cu eutectic alloy,&apos; where it was found that strain rate sensitivity of cast material annealed to produce an equiaxed, micron-size grain is always low; taking as an index of rate sensitivity m = a log a/a log <, m < 0.3. However, m in hot-worked alloy of comparable grain size can be as high as 0.7. In the cast and annealed material, each phase is a single crystal, the only boundaries are interphase boundaries, and it is, consequently, geometrically impossible for boundary shear to contribute to deformation in any major way. Other observations (for hot-worked material) were a-L at constant (low) strain rates and indications that the rate of recrystallization was enhanced as strain rate increased. As a result of this work, it was proposed that high rate sensitivity arises from a deformation mode of boundary shear associated with boundary migration. Migration serves to relieve stress concentrations at triple points, and smoothes boundaries so that they assume properties of fluid films. On the other hand, the low rate sensitivity observed at high and low strain rates reflects deformation of bulk material. Measurement of the variation of grain boundary shear with strain rate and m have not yet been made. Such measurements are important, especially in view of a proposal, differing in detail from the above, that high m arises merely from a transition between a grain boundary shear mode of deformation at low rates to a transgranular mode at high rates.2&apos;4 In the present work, the contribution of boundary shear to total deformation is measured and in addition metallographic observations are made on surfaces of deformed specimens to look at the interaction between boundary shear and migration. The Al-Zn eutectoid alloy was chosen for its homogeneous, fine-grained structure, which is obtained readily without hot-working. It has also been the subject of a previous phenom-enologically directed study. EXPERIMENTAL Material. Compression specimens, cross section 4 by + in., length \ in., were machined from a sand-cast ingot of composition 77.5 wt pct Zn, 22.5 wt pct Al. (The melt was prepared from 99.9 pct Zn and 99.99 pct Al.) After homogenization at 375°C for 50 hr, the specimens were quenched in brine and removed before the heat evolution that accompanies de -composition of the high-temperature phase.5&apos;6 The resulting microstructure, see Fig. l(a), was too fine for grain boundary sliding to be easily studied; coarser structures were obtained by annealing for various times at 2 50°C. Annealing was terminated by a brine quench. Final average intercept lengths between all grain boundaries (both interphase and those lying in a phase), L, were: 0.5 p [annealed for 15 min, Fig. (a)], 0.8, 1.1, and 1.8 p [Fig. l(b)l. Testing Procedure. An Instron machine was used for most of the compressive deformation. Tests were of two types: those in which crosshead velocity was changed in steps to measure m as a function of strain rate15 and tests at constant velocity to a fixed (engineering) strain of -0.2 (20 pct). Stress reached a steady-state value (a) which was plotted, on a logarithmic scale, against log strain rate (E&apos;). An alternate and equivalent evaluation of m was to take the slope of the log o vs log 6 curve. Time at temperature before testing was 15 min. Strain rates covered by the Instron (4 x lo-&apos; to 4 x 10&apos; per min) were insufficient; at a higher rate of 5 x lo2 per min a gas-operated testing machine was used, the gas driving a piston to compress the specimen at a controlled velocity.&apos; To obtain points on the log a vs log E&apos; curve at low rates, specimens were compressed by a dead weight. strain rate was an average value computed by dividing strain at the end of test by loading time. In some tests strain was measured at fractions of the loading time; creep rate was found to be reasonably constant.

Jan 1, 1969

By C. Laird, C. E. Feltner

May different kinds of dislocation structures have been observed in strain-cycled metals and alloys. In order to understand their pattern and causes, an experimental program has been carried out to determine the influence on the dislocation structures of the three variables: 1) slip character of the material, 2) test temperature, and 3) strain amplitude. The results show that at high strain amplitudes cell structures me formed when the slip character is wavy, and that these are progressively replaced by uniform distributions of dislocations as the stacking fault energy is decreased. At lower strains, dislocation debris is formed which consists primarily of dipoles in wavy slip mode materials and multipoles in planar slip mode materials. Temperature merely acts to change the scale of the structure, smaller cells, and clumps of dislocation debris being associated with lower temperatures. It is shown that the results for many metals fit this pattern, which Parallels that occurring in unidirectional deformation. DISLOCATION structures produced by cyclic strain (fatigue) have been examined in a number of metals by transmission electron microscopy. These studies have produced a variety of interesting and often seemingly conflicting results. For example, different investigators have reported such structural features as cells.le4 bands of tangled dislocations,4&apos;5 dense patches or clusters of prismatic dislocation loops, planar arrays,4&apos;10 and various combinations or mixtures of these different structures. Most of these observations have been made on materials which were initially annealed and cyclically strained at low amplitudes resulting in long lives. Recently we have reported observations of the dislocation structures produced in copper and Cu-7.5 pct Al cycled at large amplitudes, resulting in lives of less than 104 cycles.4 These results, examined in combination with those in the literature, have suggested that a common or consistent structural pattern exists. Variations in this pattern appear to be determined chiefly by the three variables, namely, the slip character of the material,4,11 test temperature. and the strain amplitude. To verify this interpretation, we have studied [he influence of the above three variables (in different combinations) on the resultant structures in cyclically strained metals. Copper, fatigued at room temperature, was chosen as a reference state to which all other observations can be compared. The effect of slip character has been investigated by employing fcc metals of different stacking fault energy. Thus aluminum which has a more wavy slip character than copper, and Cu-2.5 pct A1 having a more planar slip char- acter, have been examined. The aluminum samples were fatigued at 210°K thus making their homologous temperature equal to that of copper at room temperature. The influence of temperature has been evaluated by examining the structures in copper at room temperature and 78°K. Finally the effect of strain amplitude was studied by looking at the structures at amplitudes giving lives ranging from 104 to 107 cycles. All of the specimens were examined at the 50 pct life level at which stage the structures have reached a stable configuration.12 I) EXPERIMENTAL PROCEDURE Strip specimens, 0.006 in. in thickness, were prepared from base elements of 99.99 pct purity or greater. Specimens were fatigued by cementing the strips to a lucite substrate which was subjected to reverse plane bending. This method of testing has been described e1sewhere.7 After fatiguing, specimens were thinned and examined in a Philips EM 200 which was equipped with a goniometer stage capable of ±30-deg tilt and 330-deg rotation of the specimen. On the basis of separate calibrations,13 allowances were made for the relative rotation and inversions between the bright-field images and the diffraction patterns. II) RESULTS AND DISCUSSION The life behavior of the materials under different test conditions is shown in Fig. 1 in the form of plots of total strain range vs cycles to failure. Comparisons of structures produced in the different materials were made at amplitudes which produced equal numbers of cycles to failure. The influence of strain amplitude on the structures produced in the reference state material (copper tested at room temperature) is shown in Fig. 2. At the 104 life level the structure produced comprises cells similar to those previously observed.3,4 They are approximately 0.5 p in diam and the cell walls are generally more regular or sharper than those produced by unidirectional deformation.14 At the 10&apos; life level the

Jan 1, 1969

Stope control information at the C.S.A. mine is obtained by diamond drilling inclined holes from within the stapes. Practical mining outlines are determined from complicated ore contours by a joint mining engineering and geological study. Production holes to achieve this outline are individually marked up and checked. Stope control also extends to selective mucking of ore mixtures for metallurgical reasons and to marginal ore and waste mixtures for economic reasons.

Jan 1, 1969

By Martin H. Stanczyk

Under the Solid Waste Disposal Act, the Bureau of Mines initiated several accelerated in-house research programs to develop new and improved methods of proper and economic solid waste disposal. The program being conducted at the Bureau&apos; College Park Metallurgy Research Center is concerned with eliminating the current waste of valuable materials in municipal refuse by developing low-cost methods for reclaiming and recycling the metal and mineral values contained in incinerator residues. Each year the United States must collect and dispose of in some manner or other, about 150 to 200 million tons of municipal solid wastes. The monetary output for this service ranks third among public services, exceeded only by the costs for schools and roads based on population growth projections and materials use patterns, the quantity of refuse generated by the early 1980&apos;s may approach 300 million tons annually. Currant estimates indicate that only 10 to 20 percent of the total municipal refuse generated is disposed of by incineration. If all refuse were properly incinerated the residues would contain more than 11 million tons of iron and nearly a million tons of mixed nonferrous metals including aluminum, copper, lend, zinc, and tin.

Jan 1, 1969

By J. R. Hauber, N. R. Borch

A study uras made on the creep behavior of cast and extruded SR grade beryllium. It is shown that, for stresses below about 1000 psi in the temperature range 760" to 85o° c, the creep behatior is nearly exactly described by the Nabarro-Herring mechanism. The activation energy is apparently that for self-diffusion, 42 2 kcal per mole, below 1000 psi, but it rises to 88.6&apos; kcal per mole at higher stresses. The slress exponent is 4.5 at the higher stresses. Tertiary creep in this material is clearly related to void formation apparently caused by grain boundary sliding. BERYLLIUM is becoming an increasingly important technological material. A search of the literature has revealed a lack of fundamental studies on the creep of beryllium. This investigation was therefore undertaken to gain insight into the creep behavior of this material. EXPERIMENTAL PROCEDURE Tensile creep samples were prepared from cast and extruded SR grade beryllium. The vendor&apos;s chemical analysis of the beryllium tested is shown in Table I. The test specimens were machined as shown in Fig. 1 from i -in.-diam rods. The machined creep specimens were annealed to remove surface damage and to establish a variation in grain size. The heat treatments and their resulting grain diameters are shown in Table 11. The average grain diameters were determined by the intercept method. True average grain diameters were estimated by multiplying the measured average grain diameters by 1.5.&apos; The creep tests were performed at temperatures from 700" to 850°C in a vacuum of 105 Torr or better in a tantalum-element resistance furnace. Loads were applied by an Instron testing machine such that the stress was held constant to within 20 psi. The test temperature was measured by thermocouples on the sample. With one exception the deviation from the desired test temperature was 2"C, and in that case the deviation was 4"C. Elongations were measured by an extensometer within the vacuum chamber which was fastened to the creep specimens at the grooves in the grip ends, as shown in Fig. 1. The precision of measurement of elongation was 1 X loe4 in. The creep tests were begun only after thermal equilibrium had been established in the sample and the extensometer to insure that there was no strain rate component due to transient thermal effects. Two kinds of creep experiments were performed. First, at constant grain size, the effects of varying stress and temperature were studied. In the second set of experiments, the temperature was held constant and the grain size was varied. The activation energy for creep was determined by varying the temperature at constant stress, as described by orn, during the first set of experiments. The variable grain size experiments revealed that creep at low stress apparently occurred by the abarro-errin&apos; mechanism. In all of the creep tests, the stress was held constant only until sufficient strain had occurred to accurately determine the creep rate. The stress was then raised to a new value and the new creep rate determined. This process was reported until tertiary creep occurred. In this manner several data points were obtained from each specimen. The assumption was made that the structure was not changing appreciably between the incremental stress levels. This was verified by reducing stresses to previously tested levels and comparing the creep rates with the creep rates obtained at the lower strains. The re-producibility was within experimental error over strains on the order of 1 pct. EXPERIMENTAL RESULTS A typical series of creep tests is shown in Fig. 2. Primary creep was not observed in any test. Transient creep, which we define as creep rates that are nonlinear with time, was not observed for any change in stress except where tertiary creep occurred. The absence of both primary and transient creep has been previously reported for hot-pressed powder beryllium.= The data for the creep behavior at constant grain size are summarized in Fig. 3. The data show two distinctly different stress dependencies. At stresses below about 1000 psi, in the equation:

Jan 1, 1969

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By J. H. Bechtold, R. Kossowsky

1 HE superplastic behavior of the eutectoid A1-78 wt pct Zn alloy has been thoroughly investigated by Back-ofen et al.&apos; The superplastic elongations and the marked resistance to necking were rationalized in terms of high strain rate sensitivity. In a subsequent paper2 superplastic behavior was formulated to show Nabarro-Herring diffusional creep as rate controlling at low strain rates, giving way to a dislocation climb process at higher strain rates. In a paper devoted to an interpretation of superplasticity in two-phase alloys, Packer and sherby3 have included the results of an examination of the structure of an Al-Zn eutectoid specimen before and after superplastic deformation. No significant change in grain size or directionality was observed in the deformed microstructures. This one observation led the authors3 to suggest that con- tinuous recrystallization or grain boundary migration was responsible for superplasticity. The purpose of this note is to report our observations on the superplastic behavior of the Al-Zn eutectoid alloy which differ in certain respects from works previously reported. Following Hayden et al., the results are discussed in terms of dislocation climb as the important factor during superplastic deformation. A heat of nominally high (99.995) purity 22 wt pct A1-78 wt pct Zn was induction-melted and cast into a 0.5 by 6 by 12 in. slab. The slab was heated to 350°C and rolled to 1/8-in.-thick plate. The plate was then cold-rolled to 0.040-in. thickness, annealed at 35OaC, and rolled to the final thickness of 0.020 in.* Speci-

Jan 1, 1969

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

The lead concentration of flotation feed ore slurries is determined using two ?-ray absorption gauges mounted directly on a 6 in. diameter flotation feed pipeline. One gauge is a conventional &quot;density&quot; gauge using CS137. The other is a &quot;lead-sensitive&quot; gauge, which depends on the preferential absorption. by lead of 225 key y-rays resulting from Compton backscatter of CS137 y-rays.Gauge outputs are combined using an analogue computer the output signal of which is directly proportional to the lead concentration of the pulp. The accuracy of measurement of the pulp lead concentration is &#177; 3&#183;6 per cent for ore slurries with lead concentrations in the range 0&apos;07-0&#183;16 g/c.c. and pulp densities 1.43-1.60 g/c.c.This paper sets out the development of the technique and details are given of the two experiments (1964, 1966) conducted in the plant at North Broken Hill Limited. The installation of the two-gauge system inthe plant during May 1968 is described. Details are given of the calibration technique used and the results obtained.

Jan 1, 1969

By Ross W. Smith, M. E. Wadsworth, T. James Smolik, A. S. Peck

Ross W. Smith (Acting Instructor, Department of Mineral Engineering, Stanford University, Stanford, Calif.) and T. James Smolik (Kennecott Copper Corp., Salt Lake City, Utah) - Professors Peck and Wads-worth have made an interesting contribution to the study of fluoride activation of beryl. We have a few comments to make regarding the paper and a question to ask of the authors. We note that glass containers were used in the study. Hydrofluoric acid should react with glass to produce SiFg2 in quantity which could adsorb onto the beryl surface (onto either beryllium or aluminum sites). The authors propose that individual F- ions actually go into the mineral surface lattice rather than onto the surface by adsorption of siFi2 ions. Based on infrared reverse bands with an untreated

Jan 1, 1969

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick&apos;s second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method&apos; are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5&apos; could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5&apos; or Ag&apos;lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5&apos; and 0.6 N HNO3 solution for the A"&apos;), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5&apos; atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.&apos;j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?&apos; for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4&apos;5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,&apos; is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel&apos;s work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969

By J. W. Downey, A. E. Dwight, M. H. Mueller, H. Knott, R. A. Conner

Sixty new ternary equiatomic compounds are reported with a hexagonal crystal structure that is isostructural with or very similar to Fe2P, D3h-P62m. HoNiAl is a typical example, with a, = 6.9893 ± 0.0003Å, C, = 3.8204 ± 0.003Å, and c/a = 0.54 7. Three holmium atoms occupy (g): x,0,1/2 three aluminum atoms occupy (f): x,0,0; one nickel atom occupies (b): 0,0,1/2; and two nickel atoms occupy (c): 4, + , 0. The nonequivalent 1(b) and 2(c) sites give rise to two sets of unequal interatornic distances (i.e., Ho-Ni and Al-NL in the case above), which account for the prevalence of Fe2P-type tertmry compounds and the scarcity of binary examples. Unit-cell constants are presented for the sixty compounds and density measurements on the compounds HoNiAl and UFeGa confirm that three formula weights are present per unit cell. Neutron and X-ray powder diffraction intensity measurements were made on CeNiAl and HoNiAl, respectively. The atomic posiLiotml parameters in CeNiAl were determined from neutron data to be x = 0.580 5 0.001 for cerium and 0.219 5 0.001 for aluminum. An investigation of the quasibinary section between the binary compounds CeNi2 and CeA12 revealed a new ternary compound CeNiAl. The compound has a hexagonal structure and is isostructural with the prototype compound Fe2P. Additional examples discovered or confirmed in this investigation provide a total of sixty ternary compounds that are isostructural with or closely related to Fe2P. Previous investigators1&apos;2 reported the unit-cell constants for the hexagonal compounds UFeA1, UCoAl, UIrA1, ZrNiAl, ZrNiGa, HfNiAl, and HfNiGa and the present investigation has confirmed that the compounds are isostructural with Fe2P. Independently, Steeb and petzow3 reported the same structure type for UCoAl, UIrA1, and UNiA1. However, the present results suggest a different atomic site occupancy for the component atoms in the three compounds. A detailed investigation of the relative positions of the three kinds of atoms in the compounds CeNiAl and HoNiAl will be discussed. EXPERIMENTAL PROCEDURE The equiatomic alloys were prepared from elements of 99.9+ pct purity by arc melting under a helium-argon atmosphere. After homogenization at temperatures from 700" to 900&apos; C, a metallographic examination was performed by conventional methods, and density measurements were carried out by the immersion method in CCl4. A powder sample was prepared for diffraction studies by crushing a portion of the annealed button. X-ray diffraction patterns were obtained with a Debye-Scherrer camera, in which the annealed powder was glued to a quartz filament, and indexed with the aid of a Bunn chart. Unit-cell constants were calculated from the computer program of Mueller, Heaton, and Miller4 and d spacings were obtained by the program of Mueller, Meyer, and Simonsen.5 The intensity values were calculated from the relation I, ~ (m)(L.P.)F2 by a computer program written by Busing, Martin, and Levy.6 The absorption and temperature correction factors were neglected. An X-ray study of HoNiAl was carried out to take advantage of: large differences in atomic scattering factors for holmium and aluminum, X-ray patters free of background darkening, negligible oxidation at room temperature, and negligible weight loss in the preparation of this alloy. The neutron diffraction studies were made on a powder sample of CeNiAl contained in a -in. diam V tube and a pattern was obtained with neutrons of wavelength The neutron scattering factors employed (x 10-12 cm). In contrast to the scattering amplitude for X-rays, cesium does not have the largest cross section, however, there is a sufficient difference in the neutron scattering amplitudes to distinguish between the atomic species. The neutron transmission was high, 86 pct; therefore, absorption corrections were not necessary for the cylindrical sample. Most reflections could not be observed individually, because of the relatively large unit cell (a = 6.9756 and c = 4.0206Å) and relatively short neutron wavelength; therefore, the intensity of grouped reflections was considered. The Kennicott modification7 of the Busing-Martin-Levy program6 was employed to determine the identity of the atoms at the various lattice sites and the positional parameters. RESULTS A structure for the prototype compound Fe2P was first reported by Hendricks and Kosting;8 however, the structure was in error. The correct structure, as reported by Rundqvist and Jellinek,9 is as follows. The unit-cell constants and volumes per formula weight (V/M) are given in Table I for the sixty compounds examined in this investigation and classified as Fe2P-type compounds. The structure type was determined initially from a comparison of the unit-cell constants of HoNiAl with other known examples of this structure type1&apos; and from the density of HoNiAl, given in Table 11. The density indicated that three formula weights comprised a unit cell, as in the prototype compound Fe2P. The assignment of the three species to lattice sites was made initially on the basis of atomic size. The large holmium atoms were assigned to the 3(g) sites that have a relatively large interatomic distance to nearest neighbor positions, the small nickel

Jan 1, 1969

By Ronald J. Roman

A mathematical model was developed for the grinding and flotation section of Union Carbide&apos;s Bishop mill and this model was used to indicate how variations in grind, retention time, and calcite and fluorite content effects the mill capacity, tungsten units produced, and the grade and recovery of the scheelite concentrate. A model such as this is a starting point in determining the economic optimum running condition for a mining and milling operation and an example of this is given.

Jan 1, 1969

By O. N. Carlson, W. M. Paulson

A phase diagram is proposed for the Y-C system based on the vesults of thermal analyses, microscopic obsevvations, and X-ray diffraction studies. Three intermediate phases occur in the system: a congru-ently melting fcc phase with a wide range of homogeneity about the composition Y2C, an intermediate solid-solution region between 55 and 58 at. pct C, and a bct dicarbide melting congruently at 2415°C. All three compounds undergo a phase transformation at elezlated temperatures. A continuous serzes of solzd solutions exists between the fcc phase and the high-temperature form of YC2 with a maximum in the solidus at 2000°C and 30 at. pct C and a minimum at 1805°C and 54 at. pct C. THIS investigation of the Y-C system was undertaken as part of a nuclear materials development program. Yttrium-base alloys are of interest as possible containers for liquid metals, and carbides are currently receiving increased attention as high-temperature materials for advanced reactors and other applications. Previous work on this system was limited in scope, and the results were somewhat inconclusive and at times contradictory. Spedding et al.&apos; reported the existence of a triyttrium carbide having an fcc structure with a wide range of homogeneity and Dean et a1.2 reported the existence of a rhombohedra1 phase having the stoichiometry of Y2C. Bachella et a1.3 observed that the latter was the result of ordering of carbon atoms in the fcc solid solution. The ordering range was placed at 800" to 1000°C. Vickery et a1.4 reported a high-melting compound which they identified as yttrium dicarbide, and Spedding and coworkers1 determined the structure of this phase as bct with lattice parameters a = 3.66 and c = 6.17A. Samsonov et al.5 reported the melting point of YC2 as 2300" * 50°C. Recently Bowman et a1.6 found a transformation in the dicarbide from the tetragonal to an fcc form at 1320 20°C. Samsonov and coworkers7 reported a monocarbide of yttrium melting at 1950" * 20°C and also a sesqui-carbide melting at 1800" * 50°C. The existence of the latter has also been indicated by others,1&apos;8 but neither compound has been definitely established. The Y-C phase diagram shown in Fig. 1 was proposed by Chubb and Keller8 in 1964 based on the data available at that time. The tentative nature of this diagram together with the uncertain status of the compounds indicated that additional work on this system was needed. EXPERIMENTAL PROCEDURE Yttrium metal of 99.9 pct purity was prepared for use in this study by the reduction of YCl, with calcium to form a sponge product.9 The major impurities in this material were as follows: 100 ppm C, 150 pprn H, 20 ppm N, 300 to 1000 ppm O, <20 ppm Ca, <100 ppm Cr, <80 ppm Cu, 150 ppm Fe, <30 pprn Mg, <400 ppm Ta, and <100 ppm Ti. Alloys were prepared by arc melting yttrium sponge together with pieces of high-purity graphite rod in a purified argon atmosphere. Homogeneity was insured by repeated melting, inverting the ingot between melts.

Jan 1, 1969