Search Documents

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-' It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969

By Minoru Sasabe, Mayurni Sorneno, Kazuhiro Goto

I) The Object of the Present Experiment. When the oxygen chemical potential in the gas phase is changed, the oxygen chemical potential in the liquid metal or in the liquid oxide phase will be subsequently changed. The object of the present experiment is to develop a method of measuring the change in the chemical potential of oxygen in liquid metals and in liquid oxides with respect to time, when the oxygen potential in the gas phase changes. II) The Experimental Method. The following types of the oxygen concentration cells with the solid electrolyte of Zr0z-CaO are used: KAZUHIRO GOTO, MemberAIME.MINORU SASABE,and MAYUMl SOMENO are Associate Professor, Research Associate, and Professor, respectively, Department of Metallurgical Engineering, Tokyo Institute of Technology, Meguro-ku, Tokyo, Japan. Manuscript submitted March 12, 1968, EMD. Igas phase liquid Ag or Pb ZrO2-CaO electrolyte!, The measured reversible electromotive force can be expressed by the next equation, provided that the transference number of the oxygen anion in the electrolyte is unity: E = RT/nF log (at electrode I)/P~ (at electrode 11) where is the electromotive force, R is the gas constant, T is absolute temperature, n is valence of oxygen anion, and Pq is the oxygen pressure at the electrodes. As shown in the previous work1 of the authors, the electromotive force is determined by the difference in the chemical potential of oxygen at the vicinity of the interfaces between the solid electrolyte and the electronic conductors used for the two electrodes. Fig. 1 shows the two kinds of the cell assembly used to measure the change of the chemical potential of oxygen in liquid metals and liquid oxides with respect to time. In both cases, the change of the oxygen pressure in the gas phase is measured by the independent oxygen concentration cell located above the

Jan 1, 1969

By Roger Díaz de Cossio

El presente artículo describe algunos aspectos de la educación de la carrera profesional de ingeniería en Europa. Para ello, se obtuvo información de educadores de países como: Inglaterra, Francia, España, Italia, Alemania, Portugal, Bélgica, Suecia, Polonia, Yugoeslavia, Finlandía, Austria y Holanda, donde se evaluó la cantidad de años reales para obtener de título de Ingeniero Civil, en qué niveles está dividida la educación de ingenieros en el país; el nivel de matemáticas que debe poseer un ingeniero al recibir el primer grado; los posibles estudios postprofesionales que existen respecto a la carrera; el número de estudiantes por cada escuela de ingeniería, métodos de enseñanza, y el porcentaje de materias básicas para alguna ingeniería, los materias de aplicación y las herramientas comprenden los programas de las escuelas de ingenierías.

Jan 1, 1969

By R. L. Sundeen

Trackless vehicles, as the name implies, are machines not bound to rails, guide cables, or other direction controlling devices. They include, for the most part, vehicles which are wheel or crawler (track laying) mounted. Power sources may be self contained such as diesel or battery and can be defined as non-captive machines, while connected power sources such as compressed air or electric can be defined as captive machines. Trackless vehicles are used in all phases of underground excavation, loading, hauling and dumping. Early application found most machines with digging ability used to load those with payload hauling ability. As the versatility of trackless methods became more obvious the trackless vehicle has evolved to more productive machines such as the self loading haulers commonly referred to as Load-Haul-Dump equipment. Trackless vehicles find wide use in drifting and tunneling. Ability to negotiate adverse grades is especially noteworthy. Experience drawn from highly efficient room and pillar mining operations has lead to relatively wide application in drawpoint and cut and fill mining.

Jan 1, 1969

By R. R. Judd, H. W. Paxton

The rate of dissolution of cementite was studied in three low-carbon materials: a zone-refined Fe-C alloy, an Fe-0.5pct Mn-C alloy, and a commercial low-carbon steel. The materials were spheroidized, ad then held isothermally at temperatures above the Al. The isothermal anneal was interrupted periodically by a water quench and the specimens were analyzed by quantitative metallography for the amount of aus-tenite formed during the anneal. The results of this study were compared with an analytical model for the process, which assumes that carbon diffusion in aus-tenite is the rate-controlling step for the cementite dissolution process. The correlation between the model and the experimental data is excellent for the zone-refined Fe-C alloys; however, the Fe-0.5 pct Mn-C alloys and the commercial steel deviate from the calculated model. This deviation is thought to be a result of manganese segregation between the carbide and the matrix. The rate of nucleation of austenite at carbide interfaces was reduced by the manganese addition and enhanced by the presence of ferrite-ferrite grain boundaries. PREVIOUS investigations of the nucleation and growth of austenite from ferrite-carbide aggregates are not entirely satisfying for at least one of several reasons. The most prevalent of these is a lack of quantitative data. Engineering studies have been run on many steels with little control over important parameters such as composition and initial aggregate structure. The data obtained are valid only for material with identical chemistry and thermal history. A more informative approach to the problem of aus-tenitization would be to determine the mechanism that controls the rate of solution of carbide in austenite and how it is modified by alloying elements. This information could then be used to calculate an austeniti-zation rate for any material, provided its composition and structure are known. The object of the present work is to establish the rate-controlling step for cementite dissolution in Fe-C austenite and to investigate the modification of this rate by small manganese additions. The composition and structure of the material used were carefully controlled and all measurements were designed to allow a quantitative analysis of the kinetic process that controls the austenitization rate. A MODEL FOR DISSOLUTION OF CEMENTITE Cementite dissolution has been analyzed mathematically by a model that approximates the material used in the experiments. This model postulates a regular ar-array of identical cementite spheroids with 4 C( diam, embedded in a grain boundary- free ferrite matrix. The analysis provides a detailed description of the dissolution of one carbide spheroid and a generalization of the solution by summation over all the carbides in the material. The carbides may be isolated by defining identical, space-filling cells of ferrite around them. If the cell dimensions are greater than the diameter of the austenite sphere resulting from complete dissolution of the carbide, and no interaction (through diffusion in ferrite) takes place between cells during the dissolution process, the model need concern only one cell, since the solution in each cell is identical. In the experimental material, the dimensions of the cell, the carbide, and the final austenite sphere are approximately 24, 4, and 8 p, respectively; use of the single cell is therefore justified. The experimental observations are made on the austenite nodules that form around each carbide during the dissolution process. The model concerns the growth of these austenite nodules. The attendant shrinking of the carbide can be obtained from the same analysis by an extension of the calculations. Several a priori assumptions are necessary to make the analysis of the growth problem tractable. They are: 1) carbon diffusion through the austenite nodule is the rate-controlling process; 2) local equilibrium exists at all interfaces, 3) the austenite nucleus that forms on each carbide instantaneously envelops the carbide; 4) during the austenite growth process, the diffusion flux of carbon in ferrite is insignificant; 5) a quasi-steady state exists in the austenite concentration field; that is, at any instant during the dissolution process, the austenite carbon concentration gradient closely approximates that for a steady-state solution; and 6) the effects of capillarity on the dissolution rate of the carbides can be neglected. Referring to Fig. 1, a mass balance at the y-a interface for an infinitesimal boundary movement gives: Where rb is the outer radius of the austenite shell, C1 and C are carbon concentrations at the interface in austenite and ferrite, respectively, see Fig. 2, is the diffusion coefficient of carbon in austenite for the concentration of carbon at the interface, and t is time. The fifth assumption permits the austenite carbon concentration to be approximated by the Laplace solution for the spherical case. Therefore, where C(Y) is the carbon concentration at r, and A and B are constants. Local interfacial equilibrium fixes the boundary conditions for the diffusion problem. They are:

Jan 1, 1969

By L. F. Bryant, J. P. Hirth, R. Speiser

The surface, gain boundary, and twin boundary energies, as well as the surface diffusion coefficient, of cobalt were determined from tests at 1354°C in pure hydrogen. A value of 1970 ergs per sq cm was calculated for the surface energy, using the zero creep method. It was possible to measure the creep strains at room temperature because the phase transformation was accompanied by negligible irreversible strain and no kinking. Established techniques based on interference microscopy were used to obtain values for the other three properties. The gain boundary and twin boundary energies were 650 ad 12.7 ergs per sq cm, respectively, while a value of 2.75 x l0 sq cm per sec was determined for the surface dufusion coefficient. In the course of a general study of cobalt and cobalt-base alloys, information was required about the surface energy of cobalt. Hence, the present program was undertaken to measure the interfacial free energy, or, briefly, the surface energy, of the solid-vapor interface of cobalt. The microcreep method was selected for this measurement because other surface properties could also be determined from the accompanying thermal grooving at grain boundaries and twin boundaries. A brief summary of the methods for determining the various surface properties follows. At very high temperatures and under applied stresses too small to initiate slip, small-diameter wires will change in length by the process of diffu-sional creep described by Herring.1 The wires acquire the familiar bamboo structure and increase or decrease in length in direct proportion to the net force on the specimen. For a specimen experiencing a zero creep rate, the applied load, wo, necessary to offset the effects of the surface energy, y,, and grain boundary energy, y b, is given by the relation: where r is the wire radius and n is the number of grains per unit length of wire. The first results obtained from wire specimens were reported by Udin, Shaler, and Wulff.' udin3 later corrected these results for the effect of grain boundary energy. The grain boundary energy is determined from measurements of the dihedral angle 8 of the groove which develops by thermal etching at the grain boundary-free surface junction. For an equilibrium configuration: Measurements of the angle 8 can be made on the creep specimens4'5 or on sheet material, as was done in this investigation by a method employing interference microscopy.= If the vapor pressure is low, the rate at which grain boundary grooves widen is determined primarily by surface diffusion and, to a lesser extent, by bulk diffusion. The surface diffusion coefficient, D,, is obtained from interferometric measurements of the groove width as a function of the annealing time, t. As predicted by Mullins~ and verified by experiment, the distance, w,, between the maxima of the humps formed on either side of the grain boundary increases in proportion to if grooving proceeds by surface diffusion alone. For this case: where fl is the atomic volume and n is the number of atoms per square centimeter of surface. When volume diffusion also contributes to the widening, the surface diffusion contribution can be extracted from the data by the method described by Mullins and shewmon.8 Where a pair of twin boundaries intersects a free surface, a groove with an included angle of A + B (using the groove figure and notations of Robertson and shewmong) forms by thermal etching at one twin boundary-free surface junction. If the "torque terms", i.e., the terms in the Herring10 equations describing the orientation dependence of the surface energy, are sufficiently large, an "inverted groove" with an included angle of 360 deg-A'-B' develops at the other intersection. The angles A + B and A' + B' are measured interferometrically. When the angle, , between the twinning plane and the macroscopic surface plane is near 90 deg, the twin boundary energy is calculated from the relation: 1) EXPERIMENTAL TECHNIQUES Five-mil-diam wire containing 56 parts per million impurities was used for making ten creep specimens. These specimens had about 15 mm gage lengths with appended loops of wire and carried loads (the specimen weight below the midpoint of the gage length) ranging from 3.7 to 149.8 mg. The wires were hung inside a can made from 99.6 pct pure cobalt sheet. Beneath the wires were placed small specimens of 20-mil-thick, 99.9982 pct pure cobalt sheet from which the relative twin boundary and grain boundary energies and the surface diffusion coefficient were measured. All the specimens were annealed at a temperature of 1354" i 3°C which is 92 pct of the absolute melting point of cobalt. The furnace atmosphere was 99.9 pct pure hydrogen that was purified further by a Deoxo catalytic unit, magnesium perchlorate, and a liquid-nitrogen cold trap. As a precautionary measure the gas was then passed through titanium alloy turnings which were heated to 280" to 420°C and replaced after every test period. The hydrogen was maintained at a

Jan 1, 1969

By J. E. Korski

Quebec Cartier Mining Co. operates a low-grade iron ore deposit at Lac Jeannine, Que., which is located at the extreme southwestern end of the Quebec-Labrador Trough (Fig. 1). The facilities there include one of the world's largest concentrators, a hydroelectric plant of 60,000 hp, and the modern town of Gagnon. A 191-mile railway connects the mine to the seaport situated at Port Cartier on the St. Lawrence River. The harbor in Port Cartier can accommodate both lake and large ocean- going vessels and is also the site of a major grain terminal. The concentrator in Lac Jeannine is designed to produce some 8 million tpy (tons per year) of specular hematite concentrate, containing 66% Fe, from approximately 20 million tons of crude ore. An annual stripping program of 5 to 8 million cu yd of waste rock uncovers the required ore. Approximately 100,000 tons of ore and waste are removed daily on a year-round, 24-hr-per-day basis. The open pit covers an area with maximum dimensions of 8,000 x 2,600 ft (Fig. 2). Present mining plans call for an ultimate depth of approximately 1,000 ft below original ground level. The rocks in the pit area are typical of this portion of the Grenville geological province. They consist largely of marble, quartz rock, pegmatite, iron formation, and stratigraphically older gneisses. The iron-ore formation consists of medium to coarse-grained specular hematite in a quartz host rock. The formation occurs locally in a plunging, anticlinal form. The topography in the vicinity of the mine is rolling, with maximum variations in elevation of about 400 ft. The hills are thickly wooded with birch, black spruce, and some tamarack. Lakes and muskeg areas are plentiful. Precipitation and temperature records have been kept since 1959. The annual rainfall has ranged between a low of 23 in. and a high of 42 in.

Jan 1, 1969

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By J. J. Frawley, W. J. Childs

PREVIOUS studies have shown that if a supercooled liquid metal was perturbed by vibration the probability of nucleation is is During a recent investi- gation to determine quantitatively the amount of energy needed to cause nucleation in a given supercooled liquid specimen, it was found that at low-energy values in the megacycle range, below the threshold energy value for cavitation, the amount of dynamic supercooling was greater than the amount of static supercooling. That is, if a specimen had a given amount of thermal supercooling under static conditions, its thermal supercooling could be increased by the addition of low-energy sound waves. The material used in this investigation was high-purity bismuth. This material was chosen because of its low melting point and the high degree of supercooling which could be easily obtained. The sound gener- ator employed in this work was a commercially built Sperry ultrasonic testing unit. This unit was equipped with a barium titanate crystal as a piezoelectric transducer. These sound waves were transmitted to the supercooled melt by a Pyrex rod, as shown in Fig. 1. The transducer was coupled to this Pyrex rod wave carrier by motor oil. The Pyrex wave carrier was approximately 1.5 ft long to prevent damage to the transducer by heat. The diameter of the Pyrex wave carrier appears to be critical. In the initial tests a wave carrier of 0.5 in. in diam was employed. However, the sound waves had no effect on the amount of dynamic supercooling. When the diameter of the wave carrier was increased to approximately the inside diameter of the Pyrex crucible, the sound waves were more effective. Approximately 200 g of metal was melted under a stannous chloride flux in a 30-ml beaker by induction heating. The temperature was recorded by a Pyrex-encapsulated chromel-alumel thermocoule which was placed in the beaker after the bismuth melted. The Pyrex wave carrier was immersed slightly below the surface of the liquid bismuth and the specimen was reheated to about 500°C. It was observed that the amount of supercooling depends on the amount of superheating the specimen receives; therefore, for meaningful results the amount of superheating was the same for all heating cycles. The specimen was allowed to cool in air and the change in temperature was continuously monitored with a potentiometric strip-chart recorder.

Jan 1, 1969

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle&apos;s work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,&apos; through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By Jerry L. Straalsund, D. Bruce Masson

A dew-point technique was used to determine the thermodynamic activity of zinc at 430°C in a series of e phase Ag-Zn alloys. The composition of the alloys ranged from 72 to 88 at. pct Zn. This range included the composition at which Massalski and King3 found a reversal in the composition variation of the crystallo-graphic c/a ratio, which they attributed to an overlap of the Fermi surface across the (002) faces of the Brillouin zone. The data is presented in a graph in which RT In yz,, where yz, is the activity coefficient of zinc, is shown as a function of atomic percent zinc. This curve has an unmistakable change in slope at the same composition that Massalski and King observed the beginning of the reversal in the c/a ratio. This change in slope of the thermodynamic data is also attributed to a Brillouin zone overlap. Equations are presented to demonstrate that the thermodynamic activity can be related to the density of states of the conduction electrons, and that the observed phenomena are consistent with this model. It is also demonstrated that the contribution of the density of states can be related to the excess stability, a phenomenological parameter recently shown by Darkeen" to be significant in the interpretation of thermodynamic data of metallic phases. The data seem to indicate that zone overlap has caused a spinodal point, and the resulting misci-bility gap, in the phase diagram. THE problem of developing an adequate thermodynamic model of solid solutions has proven to be difficult, and is still only partially solved. The main approach has been to develop a statistical model, such as that of an ideal solution, regular solution, and so forth, to which can be attached corrections for electronic, vibrational, magnetic, ordering, or other contributions. Such corrective terms are usually derived on an ad hoc basis, and it is difficult to predict in advance what their relative importance will be. This problem has been discussed in general terms by Oriani and Alcock,&apos; who have reviewed several thermodynamic models and a few empirical correlations. The measurements described in the present paper were made to demonstrate in a special case the importance of one such corrective term, the contribu- tion of the energy of the conduction electrons of an alloy. It was our premise that the contribution of the energy of the conduction electrons to the thermodynamic activity of the alloy components could be detected; further, that such an effect would be observed at alloy compositions where other phenomena, also ascribed to the energy and density of states of the conduction electrons, are observed. The idea of the importance of the conduction electrons is hardly new. Hume-Rothery and his adherents have developed the well-known theory of alloy phases in which the sequence of phase fields in binary equilibrium diagrams, especially those involving the noble metals with the IIB, IIIB, and IVB subgroups, can be correlated by replacing the composition variable with the ratio of conduction electrons to atoms, e/a. Jones and others have developed a physical explanation for this correlation, in which they consider the solubility limits of phase fields to be restricted by an intersection between the Fermi surface and a Brillouin zone. The general features of the model are also quite well-known—presumably zone intersection causes the density of states to decrease at critical alloy compositions. The attendant increase in energy of conduction electrons in the original crystal structure allows an alternate structure to become more stable as the concentration of polyvalent solute is increased. In spite of the wide acceptance of these ideas on phase stability, there is only indirect* evidence, such as the variations in lattice parameter recorded extensively by Massalskizy3 and others, that Brillouin zone interactions occur. There are few experimental measurements, other than the correlations of the phase sequence, that substantiate the premise that the energy of conduction electrons affects the solubility limits of alloy phases. Much thermodynamic data of alloys has been found to be consistent with the theory; yet there is a lack of detailed data at compositions where zone intersection and overlap are thought to occur. One would expect that the energy of the conduction electrons would make a measurable contribution to the thermodynamic properties of alloys at compositions near zone intersection and overlap if the theory of Hume-Rothery and Jones is correct. This conclusion cannot be avoided, because the phase boundaries are determined by the requirement that the chemical potential of the components be equal in both phases at equilibrium. An electronic effect large enough to alter the stability of a phase should also affect the thermodynamic activity by a measurable amount.

Jan 1, 1969

By T. Reed Scollon

Major interrelated factors to be considered in assessing the impact of air pollution control regulations on coal are: (I) the fuel and fuel-related limitations of such regulations; (2) the rate of adoption and areal scope of the regulations; and (3) the availability of fuels and fuel-burning equipment to meet the requirements. A growing number of regulations contain provisions limiting the emissions of sulfur oxides or the sulfur content of fuels or both. With few exceptions, these limitations have not yet become fully effective in those areas which have already adopted regulations, and pertinent details of future regulations or legislation for most other areas are unknown at this time. Sufficient information is not avail- able to determine the availability of low-sulfur fuels at various demand and price levels, and large-scale commercial feasibility of sulfur-oxides removal processes and equipment is believed to be some years away. Accordingly, with the many uncertainties and unknowns, it is possible at best to make only a rough assessment of the impact of such regulations or legislation on coal.

Jan 1, 1969

By Stanley C. Suboleski, J. Richard Lucas

Simulator I, a program to simulate production in room and pillar mining systems containing up to six face operations, was developed at Virginia Polytechnic Institute under sponsorship of the Office of Coal Research. Since its inception, several hundred analyses have been run, with over thirty companies using the program. This paper describes the simulation technique used in this program, the output achieved from an analysis, and reviews the experience gained in working with Simulator I.

Jan 1, 1969

By Paul A. Flinn, Jean-Marie Robert Genin

The MCssbauer effect was used to study the distribution of carbon in Fe-C alloys of high carbon content during room-temperature aging. In freshly formed rnartensite the carbon distribution is approximately random; carbon clustering occurs dun&apos;ng aging. In the retained austete the carbon atoms are isolated, suggesting an efiective repulsion; and no rearrangement during room-temperature aging is evident. The kinetics of the carbon clustering in martensite has been studied in detail at 0" . 10". and 20°C. The time and temperature dependence observed is sinzilar to that reported for a variety of other aging effects, such as resistance change, hardness increase, and recovery of internal friction. The stabilization of the martensite kransformation also appears to be related to the clustering effect. DESPITE extensive efforts since the early days of Reaumur, the mechanism which provides the strengthening of steel remains controversial in many cases for several reasons: 1) The structure of as-quenched martensite is not well-determined. 2) Experimental methods capable of distinguishing between various hardening mechanisms are not well-developed. 3) The temperature of formation of many low-alloy martensites is so high that the martensite formed during quenching may be already tempered to some extent before any observation. Among all the hardening phenomena, the most puzzling one occurs at room temperature, where no structural changes have been detected by the usual methods of X-ray diffraction or electron microscopy. However, a new and more sensitive technique became available with the discovery of the MBssbauer effect. This effect makes possible the detection of changes in the local environment of iron atoms in solid solution. It has been extensively used in the study of substitutional alloy systems, for example, Fe-Al,1 Fe-Si,2,3 Fe-Rh,4 and Fe-Ni.5 Making use of the possibility of obtaining new structural information, we undertook an investigation of the aging of high-carbon Fe-C martensite to follow the structural changes involved in the aging at room temperature. Preliminary results6 showed that a clustering of the carbon atoms occurs with time. A systematic study of the kinetics of the process showed a striking similarity to the kinetics of stabilization of the marten-sitic transformation, thus suggesting further investigation of the relationship. EXPERIMENTAL TECHNIQUE To eliminate difficulties with the aging of martensite prior to the first experimental measurements, we needed an alloy with an M, temperature not above room temperature. Other investigators7 were misled by results obtained on alloys which transformed above room temperature and underwent structural changes prior to the first Mossbauer measurements. Winchell and cohen8 dealt with this difficulty by using a third element, nickel, to depress the MS below room temperature. The presence of nickel did not seriously interfere with hardness or resistivity measurements, but it would complicate the interpretation of the Mossbauer data by increasing the variety of iron environments. We chose, therefore, to obtain the necessary lowering of the M, simply by increasing the carbon content. After the first quench to room temperature, our specimens are retained austenite, which we later quench into liquid nitrogen. The martensitic transformation takes place suddenly, so that the as-quenched condition of the samples is retained, since the temperature is low enough to prevent any carbon diffusion. A Massbauer spectrum at 77°K can be taken and analyzed; after an appropriate up-quenching to the aging temperature, a new Mossbauer measurement at 77°K can be made. Fig. 1 shows a typical cycle of experiments. The samples were foils 25 p thick of high-purity

Jan 1, 1969

By J. J. Jonas, J. L. Uvira

Equipment was constructed which permitted the hot compression of 99.8 pct Armco iron and 2.8 pct Si steel at constant true strain rates of 0.05 to 1 per sec over the temperature range 600" to 1000°C. A maximum true strain of 1.9 could be attained, followed by immediate quenching or by isothermal annealing. True stress-true strain curves were obtained, and the steady-state flout stress, a, strain rate, i, and temperature, T, were found to fit the following expression: The constants A, a, n&apos;, and AH were determined for the two ,materials. The activation energies obtained for Arrnco iron and silicon steel are 66 and 80 kcal per mole, respectively, and approximate those for seu- diffusion and for creep. This indicates that hot compression is a diffusion-controlled thermally activated process. THE hot compression of iron and steel is usually carried out in the austenite temperature range,1"7 as this is the one of greatest interest with respect to industrial hot working. However, a disadvantage of testing in the austenite range is that the hot-worked structure is destroyed by the phase transformations taking place during cooling. The present study was therefore carried out in the ferritic temperature range, and the hot-worked substructures were preserved by rapid quenching after deformation. The substructural results will be described in a separate paper, and the present communication is restricted to the strain rate/stress/temperature relationship observed during hot working. The results of hot-compression testing are usually given in the form of true stress/true strain curves, with a different curve for each temperature/strain rate ~ornbination.&apos;,~,~ Sometimes simple algebraic equations are fitted to the curves, so that certain extrapolations or interpolations can be performed.1&apos;2&apos;5 These equations are, however, devoid of mechanistic interpretations. The present study was undertaken to show that hot compression can be described by an equation of the type used in creep studies. That is, it will be shown that the temperature dependence of the strain rate in hot working is well-represented by an Arrhenius term, with an activation energy similar to that for creep. Also it will be seen that the stress dependence of the strain rate is similar to that for creep EXPERIMENTAL METHOD AND MATERIALS The investigation was carried out with the following three ferrous materials: 1) Armco iron; 2) Armco iron with 0.26 pct Mn; 3) 2.8 pct Si steel. The first two materials were utilized for investigations performed in the temperature range 600" to 800°C; the last one was used for tests at temperatures from 600" to 1000°C. The materials were of commercial purity,* as shown in Table I. Cylinders of five different sizes were prepared by strain annealing. The resulting mean grain diameter was 3 mm in the 1-in. Armco iron and 2 mm in the other sizes and grades. Different ratios of diameter/height were used to enable the determination of the coefficient of friction. The specimen faces were provided with concentric grooves, which acted as lubricant holders during compression, as recommended by English and ~ackofen&apos; and others.2&apos;9 Powdered glass lubricants were applied to the samples before hot compression to decrease friction and barreling, following the practice of previous investigator~.~~~~~~~~ Different mixtures of glass powder were used for each temperature, after the determination of suitable compositions by experiment.&apos;&apos; Equipment for Hot Compression. Hot-compression tests were carried out on an adapted 150-ton vertical hydraulic extrusion press and also on a modified high-temperature creep machine. The modified extrusion press was used for temperatures up to 800°C. The following items were added to the press: a) a high-temperature furnace with built-in upper and lower platens; and b) a transmission assembly, which permitted the attainment of logarithmically decreasing crosshead speeds. These accessories are described in detail in Ref. 11.

Jan 1, 1969

By Robert O. Vernon

Urban sprawl, and all its attendant problems, is upon us. In Florida, and much of the rest of the world, this has been intensified by a special problem - the coastal zone - a land of high-intensity urbanization localized where the sea and our citizens interact. Florida is blessed by a long coastline of beautiful beaches, indented by estuaries, lagoons and spring fed rivers. Rocky and sand covered islands invite habitation. A large and varied fauna and flora make recreation an avocation and work a pleasure. Accompanying these people are all the sustaining, and satellite industries that find the climate, labor, and commodity markets, cheap water transportation, and natural resources to be attractive. It is estimated that by the year 2008 a megalopolis will stretch down the Atlantic Seaboard from Georgia to encompass the Keys and extend along the Gulf to Alabama. This city will be fenced by the sea on one side and by the water management works, necessary to provide the water supply for this complex, on the other. What can we do about increasing the amount of water available for this population and decreasing the resultant wastes??? Rarely has there been tendered a more favorable opportunity for a coordinated planning and development project that will provide public access to beaches and multiple use of the coastal lands. Florida, as a peninsula swept by ocean breezes, having a largely indigenous water supply and only the beginning of the pollution of estuarine and coastal waters can cope with air, water and coastal dissipation and pollution, if we have a beginning at providing a constant water supply and at limiting pollution. This answer would appear to lie underground, where the porous limestones are interbedded with impervious fine-grained sediments and ground-water that circulates through these aquifers empty to the ocean and Gulf along the continental slopes.

Jan 1, 1969

By W. A. Haley

This paper discusses how a large wheel loader should be equipped, with particular attention paid to tires and tread life, and describes the several steps that can be taken to provide favorable working conditions and reduce over-all costs. A comparison is then made of wheel loader production and costs vs those of power shovels, and the present and possible future applications of the wheel loader are outlined.

Jan 1, 1969

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,&apos; Si,&apos; Ni,2-5 CO,&apos;-&apos;, Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry&apos;s law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.&apos;2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

By Paul Eimon

In the world of minerals exploration, computer-oriented data storage and retrieval methods are being talked about, studied and researched. The goal is to facilitate the recording, collating, indexing, recovery, and analysis of mineral deposit-prospect data. A survey has been made of the various report forms, suggested outlines, and computer coding forms that are currently used in mineral exploration to index and/or describe mineral deposits and prospects. These forms have a number of common characteristics: location, commodities, type of deposit, host rock, etc. Such basic mineral deposit-prospect "data units" are part of most exploration programs. "Data units" may be comprehensive bound published descriptions of mines or mining districts or 3x5 file cards or elaborate computer coding forms being developed in Canada. Initial attempts to develop computer-oriented information systems have run into the same roadblock: the lack of a body of organized, processible data describing the basic qualities of mineral deposits and prospects. To solve this problem, international committees are considering coding forms, world-wide semantics, and rules or standards for data collection and description. It appears that mistrust and lack of understanding of the computer; fear of loss of proprietary information; and disagreements over terminology are distorting the picture of what has to be done if the mining industry is to grow into more meaningful information systems for mineral exploration.

Jan 1, 1969