Search Documents

By S. S. Marsden, S. A. Khan

Externally generated foam was injected continuously into short porous media. Both flow rate and pressure drop were measured. Liquid saturation was determined by electrical conductivity. Foam yuality I, expressed as the ratio of gas volume to total volume, was varied from 0.70 to 0.96. As measured with a modified fann VG Meter, apparent viscosity of this foam µa decreases with increasing shear rate but usually falls within the range of 50 to 500 cp. At a given shear rate, µa increases almost linearly with I-. When measured with a Bendix Ultraviscoson, kinematic pa is independent of V but absolute pa increases with T from about 3 to 8 cp. The effective permeability -apparent viscosity ratio ke/µa decreases almost linearly with V for porous media of high permeability, but the rate of decrease becomes less for tighter ones. The relative permeability-apparent viscosity ratio kr/µa us V data does not fall on a single line. The kr/µa ratio increases with liquid saturation in the porous medium and with surfactant concentration. Estimates of pa for foam in porous media vary from 30 to 100 cp. INTRODUCTION Although research on the development of a foam-drive, oil recovery process has been going on for almost a decade, most of the significant publications have appeared within the last several years. This illustrates well the rate at which interest in this process is accelerating. Bond and Holbrook 1 were the first to describe the use of foam to improve oil recovery in their patent of 1958. They proposed that an aqueous foaming agent slug be injected into the formation and that this be followed by gas to produce a foam in situ. Fried 2 studied the injection of foam into porous media which had already been subjected to conventional gas or water drives and found that gas could be used to drive a foam bank which would, in turn, displace additional oil in the form of an oil bank. He attributed the increased oil recovery to the high effective viscosity of foam flowing in porous media. His microscopic observations showed the importance of foam generation and regeneration within the porous medium. By injecting both air and aqueous surfactant solution, Bernard3 generated foams within the porous medium in which oil displacement was being studied. In a separate empirical test, he also measured the dynamic foaming characteristics of the same surfactants in water and/or oil. With some exceptions and for the seyen surfactants studied, there seems to be a qualitative relationship between the efficiency of liquid rlisplacrment and the dynamic foaming testtsed. This relationship was not consistent enough to eliminate the necessity of actual foam flood tests in porous media for surfactant selection. In a study basic to gas storage in aquifers, Bennett4 described the displacement of brine by foam in consolidated porous media. Among other things, he stated that the ability of a surfactant solution to foam is more important than the stability of its foam. The presence of a foam bank between the displacing air and the displaced brine improved both breakthrough and ultimate recovery. In a continuation of this work Kolb5 attributed the great reduction in surfactant solution production rate as displacement by air progressed to a decrease in relative permeability to gas. These several effects reported by both Bennett and Kolb can all be attributed to the high apparent viscosity of foam which was obviously flowing in the porous media. Bernard and Holm6 observed that gas permeability in the presence of foam was much less than in the absence of foam when both were measured at the same gas saturations. This reduction in permeability was proportionately greater for more permeable sands and sandstones than for the less permeable. Viscosities of the surfactant solution and air were used for their calculations rather than apparent foam viscosities. The foam stability increased with decreasing permeability, which was probably due to the natural regenerative properties of porous media, and the permeability reduction increased

Jan 1, 1967

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By R. E. Reed-Hill

A simple accurate graphical method for orienting fcc crystals using (111) slip traces on a single surface is described. Solutions placing the pole of the surface in a unit stereographic triangle are obtained using a Wulffnet, a (111) standard projection showing the four (111) planes, and a (111) standard projection ruled into unit stereogmphic triangles. The multiplicity of solutions is described in relation to this method. AN accurate, rapid single-surface technique for orienting fcc crystals, using (111) slip or twin traces, has been a matter of continuing interest, as evidenced by the periodic appearance of papers on this subject.'-4 This note presents a new method possessing some advantages over those previously reported. It is an analog to the technique for hcp metals5 where the solution is based upon a stereographic rotation of the specimen surface on a (0002) standard projection that contains the planes of the possible features that might account for the observed traces. In the hexagonal solution, the axis of rotation is the basal-plane trace in the surface. In the fcc case, the axis of rotation is one of the observed ( 111) slip or twin traces. It has been observed that the solution is greatly facilitated if the indicated movements of the (111) traces during the rotation of the surface are plotted directly on a paper copy of a Wulff net as shown schematically in Fig. 1. The trace selected to represent the axis of rotation is assumed to fall at the north-south poles of the Wulff net. The directions of the other traces are then plotted as points at the proper angles around one-half of the basic circle of the net. The loci of points corresponding to the movements of these traces (directions) during a 90-deg rotation of the surface, about the polar axis of the net, are then easily and accurately drawn by following the appropriate small circles on the Wulff net. The solutions to the problem are obtained with the aid of a (111) standard projection of the (111) planes, see Fig. 2. This is normally a Xerox copy of a carefully drawn master made on high-quality tracing paper. The (111) standard projection is superimposed over the Wulff net and rotated about its center until the points of intersection of the loci of surface traces, drawn on the Wulff net, and the great circles representing the (111) traces, all lie along a common meridian of the Wulff net as demonstrated in Fig. 3. This latter great circle represents a possible position of the surface. The pole of this plane is then plotted on the (111) standard projection. Its location in a unit stereographic triangle may be readily obtained by superimposing (over the standard projection) another tracing paper (111) standard projection subdivided into unit stereographic triangles. The result of this last operation is shown in Fig. 4. MULTIPLICITY OF THE SOLUTIONS The maximum possible number of (111) traces on a single grain surface is four. Any one may be selected as the axis about which the surface is rotated. Corresponding to each such choice are three possible surface-pole orientations, related to each other by a simple 120-deg rotation about the pole of the (111) basic circle. This is a direct result of the threefold symmetry of the (111) standard projection. Since each of the four rotations will normally give a different set of three-pole positions, there are, accordingly, twelve possible solutions. Each of these twelve solutions places the surface pole in the same relative position in a stereographic triangle so that all are crystallo-graphically equivalent. Accordingly, only a single solution is required to obtain a basic orientation of the crystal. It should be noted, however, that the orientations obtained by reflecting* any of these twelve orien- *The reflected orientations may be obtained by a 90-deg rotation of the opposite sense to that shown in Fig. 1. This rotation places the correspond-ing trace loci in the lower hemisphere of the Wulff net rather than in the upper hemisphere. tations through the surface are also possible orientations that could account for the surface traces. Thus, a given set of four traces always corresponds to a pair of basic orientations related by reflection through the specimen surface. This ambiguity can only be re-

Jan 1, 1967

By J. W. Town

Studies were made by the Bureau of Mines to determine the influence of textural features on the beneficiation of phosphate minerals (pellets) from selected bed and composite samples representing different rock types of the Western Phosphoria Formation. The particle size of the samples was reduced by attrition grinding to minus 20-, 28-, or 48-mesh depending on ore grade and gangue matrix. Sizing of the ground material showed that the phosphate pellets would concentrate in the plus 200-, 270-, or 325-mesh size fractions sufficiently so that the phosphate content was above the 31.5 :cent P2O5 required for acidulation. The phosphate content of essentially pure phosphate pellets was shown to range from 33 to 39 percent P2O5. Microscopic identification of the particles in each size fraction showed that the phosphate was either in the pellet form and readily liberated or so intimately associated with the gangue matrix that size reduction necessary Co obtain liberation was impractical.

Jan 1, 1967

By P. C. Tully

The vapor pressure-temperature relationships for saturated pure liquid nitrogen are calculated by the Strobridge equation using a digital computer. This information is presented in two tables: first) in pressure increments of 0.1 psi from 1.8 to 492.9 psia) and second) in temperature increments of 0.1° from 63.15° to 126.26° K. These tables should facilitate the calibration of temperature-measuring devices over this temperature range.

Jan 1, 1967

By J. E. Flinn, E. R. Gilbert

Recently, Green reported some high-temperature, 0.60 to 0.89 T3, creep results on unalloyed tantalum. From his study he determined an activation energy of 114 kcal per mole for steady-state creep using the T, differential-temperature method25 for testing. He accounted for the difference between this value and 110 kcal per mole for self-diffusion by the temperature dependence of the elastic modulus, 4 kcal per mole. This reported activation energy is in apparent disagreement with that which can be determined from Green's isothermal data, which we have plotted as log creep rate vs 1/T in Fig. 15. From this figure, it appears that there are two activation energies of -185 kcal per mole at the higher temperatures and -75 kcal per mole at the lower temperatures. It is not obvious that the data can be fitted to a straight line corresponding to an activation energy of 114 kcal per mole. One is led to two possible conclusions regarding Green's study: there are two discrete processes controlling the creep rate from 0.60 to 0.89 Tm or the apparent activation energy is not discrete but continuously increases with increasing temperature. The former speculation would be in closer agreement with the high-temperature creep behavior of tungsten.28 The apparent disagreement between the activation energies determined by the AT and isothermal methods certainly suggests that further study on the high-temperature creep of tantalum is needed.

Jan 1, 1967

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

By T. F. Archbold, P. G. McCormick

Silica fiber 11arkevs and hardness irzdentatiozs have been used to study the thermal diffusion of racancies in zinc placed in temperature gradients of 460o and 706oK per Cm All markers mored toward the higher temperatures, and the data show that the heat of trarlsport Q is greater than the eizthalpy of z,acancj3 forrjalion E by an amount equal to 3.5 kcal per mole. These results ore not in agreement with those obtained in either of the two previous studies with zinc. The problem is discussed in terms of experimental differences and racancy source and sink efficiencies. THE general interest in thermal-diffusion phenomena over the past several years has prompted a number of marker movement studies using pure metals. In order to understand better the relationships between thermal and mass flow, a general goal of the experiments has been to obtain values for the net enthalpies carried by the diffusing atoms. For self-diffusion by means of the vacancy mechanism, the determination of relative marker positions before and after an anneal in a temperature gradient permits a calculation of a value for (Q - Ef). Q is the transferred enthalpy, and Ef is the enthalpy of vacancy formation in the metal being investigated. The initial experimental study of thermal diffusion in pure metals was accomplished by Shewmon who found essentially no movement of surface-hardness indentation markers in single and bicrystals of zinc held for 20 days in a temperature gradient of 310°C per

Jan 1, 1967

By Warren E. Morrison

The continuing high-level performance of the domestic mineral and mineral fuels industries during 1966 was sustained by the longest business upturn in the Nation's history. Spurred by consumer demand at home and the defense production requirements of the Viet-Nam war, the rising trend of economic activity during the year was reflected in the upward movements of the major economic indicators. At yearend the gross national product (GNP), representing the value of all goods and services produced, stood at $740 billion, $58 billion greater than in 1965. Corrected for price changes, the real value of GNP in terms of 1958 dollars was $648 billion and represented an annual increase in economic activity of 5.4 percent. Some 74 million persons were employed during the year out of a total population of 196.8 million, while unemployment fell below 4 percent. The Federal Reserve Index of Industrial Production averaged 156 for 1966, up 13 points from the previous year. However a jarring note in the 1966 expansion, and one which affected the mineral industries in particular, was the increasing pressure on prices and the threat of inflation. From 1961-65 economic growth was facilitated by relatively stable wages and prices and only mild inflation. During the period average wholesale prices hardly moved while average consumer prices rose only about I percent per year. But this long run of relative price stability ended during 1966 when consumer prices rose 2.9 percent and wholesale prices were up 3.2 percent from the previous year.

Jan 1, 1967

By V. B. Kurfman

The temperature, strain rate, and orientation deDendence of defbrnzation of single-crystal MgAg has been examined. The crystals exhibit a tendency to single glide and little or no hardening at 25°C for many orientations. A much higher hardening rate is observed when multiple glide occurs, such as can be initiated by surface defects. The tendency for easy glide becomes less dependent on surface preparation and orientation as T — 100°C and bars so tested often fail after one-dimensional necking-. At T > 200°C (transition temperature for single-crystal notch sensitivity and poly crystalline ductility) single glide diminishes and two-dirnensionul necking begins. The crystals do not strictly obey a critical resolved shear stress law, but show the influence of {loo) cracks in determining the slip mode. The results are correlated with the difficulty of sciperdzslocation intersection and semibrittle behavior of this compound in single-crystal and poly crystalline form. Comparisons are made with the slip selection mode observed in tungsten, with the reported observations of easy glide in bee metals. and with the mechanical behavior of poly crystalline MgAg. PREVIOUS work on tensile deformation of polycrys-talline MgAgl and bending deformation of single-crystal MgAg2 has shown that the compound is semi-brittle (i.e., notch and grain boundary brittle). If this semibrittleness is supposed to result from the difficulty of multiple glide (associated with the problems of superdislocation intersection) one might expect single crystals deformed in tension to show pronounced single glide and strong orientation dependence of hardening rate. These experiments were done to examine this supposition and to study the tensile deformation of a highly ordered system which may be considered bcc if the difference between the two kinds of atoms is ignored (actual structure: CsC1). EXPERIMENTAL Single-crystal ingots were grown by directional freezing as previously described.' These ingots were sliced into a by a by 2 in, rectangular bars by electric discharge machining, then round tensile bars were conventionally machined to 1/8-in.-diam by 1-in.-long reduced section. The bars were typically tested without an anneal because of the problem of magnesium vapor loss and they were typically tested as mechanically polished. The analyses are within the same limits as those reported earlier; i.e., the average composition for each specimen is within 0.5 at. pct of stoichiometry, while the total range from end to end in a given specimen varies from 0.7 to 1.4 at, pct. There has been no indication in the results of any variation in slip or fracture mode attributable to the composition fluctuations. The slip systems were determined by two-surface analysis of the bars after testing to failure at room temperature. Single glide was so dominant that there was little difficulty in identification of the dominant slip system even though the tensile elongation to failure often approached 7 to 8 pct in room-tempera- ture tests. Elevated-temperature testing was done in a silicone oil bath and low-temperature testing was done in liquid Np or a dry-ice bath. All stress measurements are reported as engineering stress unless otherwise specified, and crosshead travel is used as the strain measurement. RESULTS The tendency toward single glide is best seen in the pictures, Figs. 1, 2, and 3, which depict deformation at fracture as a function of test temperature. While it is possible to find regions of secondary slip by careful microscopy, such regions are very small. The development of a ribbon-shaped configuration from an initially round section bar pulled at 100°C is typical, occurred by single glide, and illustrates the degree to which such glide continues. At temperatures =100°C the bars typically show elongation of 20 to 50 pct by predominently single glide. Despite the large elongation, fracture even at 150°C occurs in a brittle mode, Fig. 2, in the sense that it is an abrupt failure which shows no discernible necking in the second dimension of the bar's cross section (i.e., there is no appreciable action of any slip modes which would decrease the broad dimension of the cross section). Near 200°C the fracture mode changes slightly. Although most of the sample extension is by single glide, after the bar develops the characteristic ribbon shape it begins to neck in the second (i.e., broad) cross-sectional dimension. The bar becomes very thin in the "necked down" region, Fig. 3, and the reduction in area approaches 100 pct. Often there oc-

Jan 1, 1967

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal' and by Chew and Connally' for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7' API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.' All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By W. S. Sanner

Seven samples were analyzed from the major reserves of the Bottom Red Ash bed, Northern anthracite field. The data show variations in thickness and geo-logic structure and in the amount of coal that can be recovered. Recovery of market-grade (less than 17 percent ash) coal is high for all samples, ranging from 76 tp 95 percent in the 3-1/4-by 9/16-inch sizes. The occurrence of coal containing less than 5 percent ash varies from 19.5 to as much as 57.5 percent. Crushing the coarse sizes to minus 9/16 inch increased recovery of market-grade coal in six of seven bed samples. Crushing released sufficient impurities to cause substantial increases in yield of coal containing less than 5 percent ash for all samples. Analyses of the float coal indicate that the quality of coal is comparable for all samples.

Jan 1, 1967

By A. Vaillant

Classifiers that are used to separate granular materials into a coarse and a fine stream, are considered. Fundamental Equations are presented which apply to all, such Classifiers and all feed size distributions. The practical, real Classifier is compared quantitatively with the perfect. Classifier. A Formula is introduced for the Real Classifier Selectivity, that defines what portion of each particle size is sent to the coarse outlet duct. This selectivity function is characterized by three Parameters, one of which (b) is a numerical measure of the sharpness of classification. A new dimensionless variable (J) appears in Equations and Graphs for recirculating load, product size distribution and specific surface in the classified product. This variable combines the effects of sharpness of separation, Classifier setting and fineness of a Rosin-Rammler Type feed to the Classifier. Classifier efficiency is defined, based on Specific Surface.

Jan 1, 1967

By E. W. Bauman

The important role that mineral aggregates assume today in the construction and chemical industries is best attested to by the astronomical tonnage figures for the annual production of aggregates in the United States as reported by the U. S. Bureau of Mines in their "Minerals Yearbook." For 1965, latest publication available, the tabulation shows a total of 1,716,000,000 tons made up of 30,000,000 slag, 908,000,000 sand and gravel, and 778,000,000 crushed stone. A much more favorable statistical position for slag can be established by listing the world-wide tonnage. According to Dr. A, W. Lee, Director, British Slag Federation, in a paper presented before the 8th Annual conference of the British Institute of Works and Highway Superintendents, he estimates that the probable world consumption of slag is in the order of 100,000,000 tons showing--Great Britain with 10,000,000 tons, Germany, 15,000,000 tons, France, 1$000,000 tons and the United States with 30,000,000 tons. Thus it is seen that the United States accounts for almost one-third of the world's consumption of slag and the 3 west European powers another third.

Jan 1, 1967

By F. Galasso, A. Paton

ThE recent emphasis on producing boron fibers by reacting boron trichloride and hydrogen on a hot tungsten wire has brought about a renewed interest in the tungsten boride phase diagram. The reaction of the boron with the tungsten core results in the formation of 6 WB, W2B5, and another tungsten boride phase, which was suspected of being the WB4 phase reported by Chrbtien and Helgorsky.1 While the powder-diffraction data for the boride in the fiber and those reported

Jan 1, 1967

By F. W. Jessen, G. F. Sears

Cavities in massive salt for the purpose of storage of liquid hydrocarbons have assumed a prominent position in recent years. This paper describes a program to facilitate leaching operations for the formation of specifically shaped storage cavities. Various forms and sizes of cavities may be possible through use of the techniques developed. INTRODUCTION The creation of large under ground storage facilities for natural gas and liquified petroleum gases has been practiced for many years. Use of cavities obtained through solution of salt for this purpose is a fairly new and novel approach, but has gained increasing importance due mainly to the economics of this type of mining operation opposed to hard rock mining or surface and pit storage.1 The idea of controlling the shape of any cavity dissolved from massive salt has not been a prime consideration of companies engaged in the formation of storage space. This has been due mainly to an insufficient knowledge of the mechanics of the leaching process and a dearth of published information dealing with both the desirability and ease of control possible for this type of operation. Two distinct advantages are readily ascertainable. From a stability standpoint (i.e., the ability of the completed cavity to withstand stress imposed by overburden pressure and lateral tectonic stresses) a controlled cavity may be generated which will yield the most favorable attitude to these external forces and remain in operable use for longer periods of time.2 A second advantage is that for a given volume, a sphere (which is one controlIed shape possible) represents the minimum surface area exposed. This may become more important in the future when dealing with refrigeration and product losses in underground cavities. The basic solution mining process, without regard for controlling the final shape, is quite simple in that the equipment and materials required to dissolve a cavity in a salt dome or layered salt section are a source of fresh water, a circulating pump, several strings of tubing and a means of disposal of the return brine. To add control measures involves the use of an inert blanket material above the position at which solution proceeds. Initially the annulus of the largest wash pipe is filled with this blanket down to the top of the proposed cavity. The bottom of the proposed cavity is determined by the depth of the original drilled hole or a blanking plug. The blanket material is added incrementally in stages and displaces the water in the enlarging cavity downward. Where the blanket material has displaced the water, no further solution takes place. The rate at which to add this controlling blanket material so as to be able to form specifically shaped cavities of any particular size is of considerable importance. THE PROBLEM It is desirable to have as much information as possible as to the behavior of the mining operation since visual observation obviously is impossible. It would be advantageous, for example, to have a step-by-step program showing how much salt is to be removed, at what rate and the time required. This type of program would facilitate procurement of surface equipment and provide for proper management of manpower requirements, as well as yield a host of intangible benefits. As mentioned earlier, only rule-of-thumb estimates were available until recently and made this type of pre-planned operation haphazardous at best. Recent work3-' has done much to clear up the ambiguities and inaccuracies attendant to solution mining of salt and has helped to place the operation on a more scientific basis. This study attempts to correlate much of the information thus far developed into a complete mining program; to extend the idea of controlled solution mining to include not only spheres, but solid conic sections of the ellipsoidal variety; and to refine the computation of the rate of removal of salt during the various stages of mining. Dommers3 and IIemson4 made extensive laboratory

Jan 1, 1967

By G. L. Barthauer

It is a distinct privilege to have the opportunity of addressing this group today. Although I, myself, am not a mining engineer, I have always had profound admiration and respect for those of you who each day live and work according to the tenets of Murphy's Law. Murphy, as some of you may know, was an Irish philosopher whose sole contribution to his field was the observation, "In the mining industry, if anything can possibly go wrong, it will!" You have heard this afternoon a variety of papers, touching on or describing in some detail imminent problems which presently face the coal industry. Many of these problems show no signs of diminishing. Actually, there is good reason to believe that they will intensify as governing bodies pass additional enabling legislation and regulatory agencies adopt more stringent "Rules and Regulations". In many cases, these groups are seemingly oblivious or indifferent to either cost factors or technical problems involved in achieving the desired goals.

Jan 1, 1967

By Don Reining

The sand and gravel industry in Southern California has made a sizeable contribution to the construction development of the 15 County area in this part of the State. Facing this mineral extraction industry, in the next decade, is a problem of meeting the market demand. The question is, "how can sand, gravel and rock operations be made compatible with goals for sound and attractive community development?" Three basic principal characteristics of the land needed for this-mining industry are: 1. The land must have workable sand, gravel or stone deposits. 2. The land must be properly located for transportation purposes close to the market in order to sell the aggregate at a minimum cost. 3. The land must be zoned so that it will be permissible to mine.

Jan 1, 1967

By A. O. P. Casbarian

An analytical method is developed to determine the variation of the ultimate lateral resistance of a plate in a cohesionless soil with depth. This analysis is based on a modification of Rankine's classical earth pressure theory and the theory of plasticity as applied to soils. The ultimate resistance is defined as the product of the effective stress at the midpoint of the plate, the area of the plate and a dimensionless variable termed the ultimate resistance factor. This variable has been plotted us the depth ratio: i.e., the ratio of of the depth of embedment us the height of the plate. The resistance of a plate may then be calculated using the values af the ultimate resistance factor from the chart provided or the equation may be programmed for use in an analysis of anchor systems in cohesionless soils. It is emphasized that the analysis is semitheoretical. The theory has been compared with experimental results reported in the literature and results indicate general agreement. Actual field tests are necessary to further verify this theory. INTRODUCTION With the exploration for oil offshore in waters all over the world, it is of importance to determine the behavior of the various soils in relation to their ultimate resistance to deformation. Examples of such problems are the holding capacity of anchors and the lateral resistance of piles. Very little information is available in the published literature on the design and performance of anchors, in either cohesive or cohesionless soils. The analysis developed in this report is the first step in obtaining a solution for the determination of anchor holding capacity in a cohesionless material. DISCUSSION The theory used in the analysis is based on the ultimate strength of the soil and is the maximum resistance developed by the plate against further movement. In such a state the elastic deformations are disregarded in comparison with the plastic deformations. Hence, the plate can be considered as completely rigid. The theory of plasticity determines the three unknown stresses at any point by means of two equilibrium conditions for a small earth element in combination with the failure condition. However, the exact solutions can only be carried out in a few simple cases such as, for example, when the rupture or failure lines are straight (Rankine theory) or with spiral and straight rupture lines (Prandtl theory).l Kiitter 2 derived a single equation expressing the variation of the stress in any given rupture line. To utilize this equation, it is necessary to know the stress in the rupture line at a certain point. Unfortunately, this is difficult to obtain unless the rupture line intersects the free surface at a certain angle or when the earth is cohesion-less and unloaded. A method to overcome this is to consider only the boundary conditions at both ends of a rupture line without investigating the equilibrium of the earth above the rupture line. This assumes that the rupture lines meet the surface at statically correct angles, so that boundary stresses may be determined. As Kiitter's equation furnished a relation between these stresses, the unit earth pressure may be calculated at the point where the rupture line meets the wall. Another way in which Kotter's equation may be applied is in investigating the equilibrium of a soil mass above a rupture line. This method assumes that the failure or rupture line is known and that the boundary stresses in the rupture line at the ground surface can be determined. In this case it is possible to determine the earth pressure from the equations of equilibrium.

Jan 1, 1967