Search Documents

By C. R. Knopp

Gas-oil relative permeability ratio is an important relationship in oil reservoir predictive calculations. A correlation has been developed from 107 gas-flood k/k tests on Venezuelan core samples. The correlating parameter is based on restored-state water saturation tests and' is applicable to both consolidated and poorly consolidated sandstone reservoirs. Data of the correlation show that there are no distinguishah1e differences between the mass-data groupings for the two c1assifications A procedure is recommended for running .sufficient relative. permeability analyses to compute a geometric mean of the sample group. The geometric mean is more representative of the total core, and probably the entire reservoir. For example, while only one in four of the k,,/k,., test curves agreed closely with the resultant correlation of this report, the geometric mean curves of the 16 suites (three samples or more). showed good agreetment ill three cases out of four. INTRODUCTION The gas-oil relative permeability ratio is an important, fundamental relationship in most oil reservoir predictive calculations. Predictive calculations are made to estimate future reservoir production characteristics and ultimate oil recovery. The k1,/k2, relationship is specifically needed to relate the surface gas-oil ratio to the reservoir oil and gas saturation, and to calculate the relative movement of these phases within the reservoir whenever some of the more complex driving mechanisms are present. Laboratory k1/k2, tests are not generally run as a routine analysis. Consequently, k1/k2 data often are not available when needed because the cost of laboratory work could not be justified or the need for such data had not been properly anticipated. When laboratory k1/k2, data are available, they are often very difficult to interpret. For example, wide divergence is sometimes shown in a family of k1,/k1, tests representative of the producing horizon in a single well. With these considerations in mind, a study was made to determine if a relationship might exist between the k1,/k2, curve and some other simple laboratory test criteria. The most probable k1/k2, curve correlation for Venezuela described in this paper is the result of the investigation. The presented correlation defines the most probable gas-flood k,,/k,, curve through the medium of air-water capillary displacement and centrifuge water saturation tests. The laboratory procedures of these tests are. relatively simple, and inexpensive; test data should be. widely available- from routine analysis. DATA AVAILABLE, LABORATORY METHODS The report correlation utilized 107 gas-Hood k1/k2, tests run on sandstone cores of Venezuelan reservoirs. Table 1 is a general tabulation of data pertinent to the tests, while Table 2 summarizes the data. Thetests include 96 from Western Venezuela and 11 from Eastern Venezuela. Eighty-two- of the 107 test samples were sandstones that varied from poorly consolidated to-unconsolidated; 25 were consolidated. The average sample porosity was 26.7 per cent and the average permeability was 1,121 md; these values typify the better sandstone reservoirs of' Venezuela. The Welge gas-flood technique,' based on fundamental Buckley-Leverett frontal displacement theory, was introduced in about 1952 and is widely accepted in the industry. The laboratory procedure is relatively simple, rapid, and can be performed on small core samples. While there have been some minor variations in sample preparation and laboratory procedure in the tests used for the correlation, these tests can be generally summarized as follows. The core sample was first sol vent-extracted and dried. Connate-water saturation was restored by the oil-flushing or evaporation-blow down methods. At the beginning of gas flood the hydrocarbon pore volume was completeiy saturated with the test oil phase. Unsteady-state gas-oil displacement then began with the injection of nitrogen or helium. while the displaced oil and gas phases were incrementally metered at the out-flow face. From the test data, the k,,/k,, curve was calculated by the Welge method.' The individual oil and gas relative permeabilities were also calculated." CORRELATING PROCEDURES In attempting to establish a basis of correlation, we found that broad mid-range sections of 105 of the 107 k,,/k,, test curves could be closely duplicated by a straight line. Only two curves did not show a degree of linearity in this region. Correlation-curve definition parameters were subsequently developed from this observation of consistent mid-range linearity. Possible correlating variables were limited to the physical properties measured on core samples that (1) were widely available as common test data and (2) could be easily and cheaply obtained through future laboratory work. The more obvious possibilities were porosity, permeability and

Jan 1, 1966

Jan 1, 1966

By J. T. Raleigh, D. L. Flock

This study investigated the nature of formation plugging with bacteria and attempted to relate its characteristics to physical rock properties. Fifteen core samples of four specific formation types were defined and plugged using a commonly occurring, uniform sized dead bacteria, Bacillus subtilis. Two of the formation types were fairly uniform-grained sandstones and two were heterogeneous carbonates. The injection rate and concentration of solids in the brine were held constant during the test runs. The pore geometry factor G was a significant petro-physical rock characteristic for correlation with depth of plugging, but lacked importance as a parameter for rate of plugging. Although the G factor may not completely describe porous rock geometry for plugging predictions, for reservoirs with multi-pore systems, there is evidence that the pore geometry factor might form a basis for establishing injection water specification in more llornogeneous reservoirs with only primary porosity development. INTRODUCTION GENERAL PURPOSE Injecting water into oil-bearing formations to increase recovery is common practice in the petroleum industry. One of the most serious operational problems involved with water injection wells is the tendency of the porous rock immediately adjacent to the injection wellbore to plug partially. This results in increased injection pressures and/or a decrease in the rate of injection. This plugging in injection wells can result from a number of causes, including bacteria contained in the injected water.1 The purpose of this work was to investigate the nature of injection plugging with bacteria and to attempt to relate its characteristics to physical rock properties. Many variables exist in research of this type, so, to reduce them, injection rate and concentration of bacteria in brine were held constant. The bacteria used for plugging was a uniform-sized, dead bacteria, Bacillus subtilis, a micro-organism commonly found in water, air and soils. Four specific porous rock types were plugged—two consolidated sandstones and two heterogeneous carbonates. The experimental work involved two distinct phases. The first concerned determining the physical rock properties and the second was the experimental work of actually plugging the selected core samples. PORE GEOMETRY FACTOR Capillary pressure is necessary to displace a wetting fluid from a capillary opening with a nonwetting fluid. The factors which govern capillary pressure are the surface or interfacial tension of the fluids involved, the system wettability and the equivalent pore radius. Thus: P,= 2ucososrd..........(1) Thomeer used the idea that the location and shape of the capillary pressure curve reflect characteristics of the pore structure of any porous media sample.' He presented the mathematical description of capillary pressure curves and of indicated differences in pore geometry of samples. where G = pore geometry factor PC = capillary pressure Pi = displacement pressure (V,)p, = fractional bulk volume occupied by the displacing fluid at any capillary pressure (V,), = fractional bulk volume occupied by the displacing fluid at infinite pressure or total interconnected pore volumes. The shape of the curve is defined by the pore geometry factor G. The curve shape is related directly to the sorting and interconnection of the pores of the sample. The location of an infinite number of curves can be defined by the same asymptotes. However, these curves differ in shape, each curve being described by a specific value of G. Thus, the description of a curve is unique when, in addition to the position of its asymptotes, its shape is defined. These curves can be used graphically to determine the characteristic parameters of any arbitrarily located curve. Those parameters that can be approximated from any capillary pressure curve are: (1) total interconnected pore volume, represented by (V,),- ; (2) extrapolated displacement pressure, the abscissa axis; and (3) pore geometry factor, by the curve shape. PROPERTIES OF BRINE AND BACTERIA The fluid used throughout this study was an aqueous solution of sodium chloride, 25,000 ppm by weight. The addition of salt to fresh water was intended to eliminate clay swelling in the sandstone cores and to retard leaching in the limestone cores. The viscosity of the brine solution at 100F, the temp-

Jan 1, 1966

By F. J. McMulkin

This paper, the 1965 Airey Memorial Lecture, reviews the world-wide technical advances in iron and steelmaking, and offers an appraisal of the new techniques which will be applied in the future. After a review of blast furnace operations, the continuous steelmaking process is described, and the resulting techniques of degassing and continuous casting are discussed at length. Pressure pouring, hot rolling, cold rolling and coating practices are also outlined, and considerable space is devoted to the direct reduction process. Finally, the application of the computer to steelmaking operations is discussed in some detail.

Jan 1, 1966

By Edmund C. Bovey

"AS I begin my remarks this morning, please let me say how honoured and gratified I was to receive your invitation to address you here during your deliberations in historic Quebec City. The high esteem in which your Institute is held is reflected in the respect and deference accorded to it by industry across Canada. I feel privileged to be here with you today.I would like to discuss with you some applications of natural gas in the mining industry and suggest to you, in closing, some possible avenues of future development.Natural gas first became avail-able for industrial purposes in Northern Ontario in late 1958. Acceptance of natural gas, as a source of energy by the industry of that area, has been both widespread and gratifying. The mining industry of Northern Ontario has in-creased its annual use of natural gas by approximately 35 per cent each year since 1958. We believe that this trend will continue, al-though we will probably have to accept a more modest 10 per cent annual gain as the market approaches saturation. I would like to explain how we were able to do this and where all this gas is used. Our first sales were largely a matter of price-and the savings we offered were substantial."

Jan 1, 1966

By Arthur Laing

"IT is indeed a pleasure to have the opportunity of addressing this group today. Not only does it give me the opportunity of meeting with representatives of what is considered by many to be the most dynamic segment of industry in Canada today, but it also allows me to talk about a subject of para-mount interest to myself, the development of the North, and to explain, if even only briefly, some of our beliefs and hopes in this regard.It is inconceivable that all lands north of the 60th parallel, representing 35 per cent of Canada's total land area, which we believe contain a great natural resource potential, will remain as an undeveloped portion of Canada. The re-sources are there, although the people and private industry are as yet not there in sufficient numbers.It has been estimated that in the west and north of Canada there are 1.6 million cubic miles of sedimentary rocks. Of this figure, 342,-000 are thought to lie in Alberta, 115,000 in British Columbia and about 1 million cubic miles are thought to lie in Canada's northern regions, the bulk in the Arctic Islands. On the basis of apparent volumes of sedimentary rock, we estimate that as much as 13 billion barrels of petroleum may lie beneath the permafrost of the North-west Territories, another 3 billion barrels in the Yukon Territory and 33 billion barrels in the Arctic Islands. This is, indeed, a rich and elusive prize, and one which must be sought with a view to fulfilling demands on the production of petroleum."

Jan 1, 1966

Mr. Robert Von Storch opened the meeting at 9:00 a.m. Mr. Von Storch: As a matter of fact, I am very much surprised to see many of these faces. The way you were acting last night I did not expect to see so many but you are evidently all right, and survived. This morning's session is the ?RESEARCH DEVELOPMENT? theme, and our first speaker- (and we made a little switch) - is Jack Huebler, Associate Director, Research Institute of Gas Technology, Chicago, Ill. The switch is because of a projector problem. Jack Huebler was born in Michigan and received degrees in Chemical Engineering and Mathematics from the University of Michigan in 1941. He joined the Surface Combusion Corp. immediately and was with them for 20 years, rising to the head of research. He took leading roles in the invention and development of many heat using processes involving gas chemistry combustion and metallurgy. The now famous Erie Mining Taconite Pellet Process was one of these. He pioneered in gas carburizing and in the preparation and use of prepared atmospheres. He specialized in the heat transfer aspects of many new industrial metal heating processes. He left Surface 5 years ago to join IGT.

Jan 1, 1966

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

By J. W. Spyker, D. H. Filson, W. H. W. Husband

"Large deposits of sodium sulphate exist in southern Saskatchewan in the brines or muddy crystal beds of alkali Jakes. Currently, more than 300,000 tons per year of sodium sulphate are produced from these lakes and sold as salt cake to the paper industry. Most of the production is obtained from the brines of a limited number of Jakes.The Saskatchewan Research Council was requested to develop a process for recovering sodium sulphate from the muddy crystal beds so that this type of deposit could be exploited in the future. A flowsheet was developed with the aid of phase diagram data and the process was studied on a pilot-plant scale using raw material from three different lakes. Satisfactory yields and product purities were obtained in all cases, and an economic analysis indicated that a 100,000-ton-per-year sodium sulphate plant could produce salt cake at a cost of $12.26 per ton for a rate of return upon investment of 16 per cent at current market prices."

Jan 1, 1966

Some important mineral fields are referred to in discussing the formation of placer deposits in Australia.Testing methods include boring by hand, with percussion rigs, with auger and pit digging drills, and by vibro drilling.Sampling errors are minimized by the use of correct techniques and equipment for boring, sampling and sample dressing. A hypothetical set of data is used to demonstrate the final process of evaluation, and somerelevant taxation provisions are discussed.

Jan 1, 1966

By Luther W. Hyde

Ground water, one of Florida's most valuable resources, is also one of its most abundant. The State is fortunate to have several prolific ground- water reservoirs that yield tremendous quantities of water to wells and to some of the world's largest springs. These ground-water reservoirs, or aquifers are of two types artesian and nonarteaian. Ad artesian aquifer is one that contains water under sufficient pressure to rise above the top of the oontaining formation. A nonartesian aquifer is one that contains water which is not confined, and the upper water surface (water table) is free to rise and fall. The principal source of ground water in Florida is the artesian Floridan aquifer which supplies most of the water users in the State. Nonartesian sources include the Biscayne aquifer of southeastern Florida, the sand-and-gravel aquifer of extreme western Florida, and a shallow aquifer which lies at depths of less than 100 feet over much of the State. The accompanying map shows the approximate areas where these aquifers are the main source of supply; however, the boundaries do not represent the areal extents of the aquifers. For example, the Floridan aquifer extends beyond the southern boundary shown on the map, but it is not of great economic significance there because the water is highly mineralized. Aquifers other than the four described occur in the State, but they are, for the most part, of minor significance. One of these is an artesian aquifer which is formed by permeable zones that occur locally within the confining beds above the Floridan aquifer.

Jan 1, 1966

By H. T. McAdams

The logic of regression analysis as an operations research tool is critically examined, and a formal basis for its application to mining problems is developed. The traditional view of regression analysis as a statistical discipline does not provide an adequate basis for evaluating a regression model in a specific area such as ore reserve calculation or process control. In particular, the validity of the residual-sum-of-squares criterion is questioned, and the need for a criterion based on interpolative features of the model is emphasized. Strictly speaking, a regression model is statistically supported only at points at which observations are available, yet inferences are drawn with regard to a continuum. When considered as a mathematical function, therefore, the model is observationally defined only on a domain consisting of a finite number of points. Extension of this domain to an interval of the real line must be based on physical rather than statistical argument. Vector space and function theory concepts useful as a logical framework for a physically oriented problem analysis are discussed and their usefulness demonstrated in a practical problem.

Jan 1, 1966

By V. J. Kniazeff, S. A. Naville

The problem of unsteady-state condensate-gas flow through porous media leads to a set of second-order non-linear partial differential equations. Such a set of equations is numerically solved in the case of radial two-phase flow around a well, taking into consideration both the thermodynamical properties of the fluid and the mechanical properties of the reservoir. The fluid properties, reflecting the PVT relationship of the gaseous and liquid phases, are expressed by using the partial specific masses of the two main separator products in these phases. The flow properties of the reservoir rock are expressed by the generalized Darcy's law for the liquid phase and by a quadratic relationship between the rate of flow and the pressure gradient for the gaseous phase. The numerical solution of the equations for pressure and saturation US radius and time is worked out through programs written for a computer. The evolution of bottom-hole pressures, well productivities or- deliverabilities and effluent compositions with the depletion of the reservoir is easily derived. The application to the Saharian gas-condensate field Hassi R'Mel led to a better understanding of the drainage mechanism. A zone of fairly high liquid saturation develops around the wells, reducing the effective permeability, and represents a loss of condensible products in addition to the PVT-like retrograde condensation. lnside this zone, near the well, the deviation from Darcy's law for the flow of the gaseous phase governs the well deliver-ability. A back-pressure test has been computed and correlates with the field results. INTRODUCTION Two-phase flow of volatile hydrocarbons, like condensate gas or light crude oil, may be treated as the flow of a binary mixture by an arbitrary division of the chemical components into two groups. This is translated into two equations of mass continuity, which constitute a set of relation- ships for the pressure and the saturations vs the space coordinates and the time. The equations contain the laws governing the composition and the motion of the phases. The problem so defined is solved with the assumption that the compositions of the phases at any pressure are respectively the same as those observed in a PVT measuring cell under differential liberation. In a first series of computations, it was assumed that the flow obeys the generalized Darcy's law. A satisfactory representation of the retrograde condensation around the well was thus obtained. In addition, the trend toward decreasing effective permeabilities was obtained, and the computed composition of the effluent checked the laboratory values. However, it has not been possible within this basic assumption to represent the non-linear relationship between the production rate and the bottom-hole pressure drawdown as observed for gas wells in the field. Following the advice of A. Houpeurt it was decided to consider the relative permeability to gas as a function of the velocity of the gas Phase.1 The necessary physical determinations were made by E. COstaséque using a method devised by A. Houpeurt and R. Iffly. As numerical processing of the equations progressed, several difficulties were encountered which were overcome through collaboration with the computer manufacturer. This mathematical model of two-phase flow in porous media had been primarily intended for and extensively applied to the case of the Hassi R'Mel gas-condensate field, operated by SN Repal for SEHR, a joint subsidiary of SN Repal and CFP (A). The programs have also found their applications to forecast the behavior of several fields in the Sahara area containing light and volatile hydrocarbons. BASIC EQUATIONS We will consider a zone in the porous reservoir where the flow properties and the in situ composition of the fluids can be assumed to be uniform. A part of the equations of transient flow can be written with the specific gravity of the fluids being taken equal to the sum of the contributions due to the

Jan 1, 1966

By Harry Perry

The Bureau of Mines is glad to have this opportunity to discuss its present Coal Research Program and its significance to the industry with a group which has for many years been representative of the coal producing community. We believe we have a dynamic program that will help our vast coal resources to find their proper place in the U. S, economy. The present coal research activities of the Bureau are conducted in three organizational subdivisions: Minerals Research, Mineral Resource Development, and Health and Safety. All investigations are carried out in Bureau research facilities located in different sections of the country, Since its creation by the Organic Act of 1910 and subsequent amendments, the Bureau has worked closely with the coal industry--first by providing assistance in mine safety for anthracite and bituminous coal mining, and since that time, in providing information on conservation, safety, mining, preparation, and utilization.

Jan 1, 1966

By Oliver Q. Leone

Electrorefining tests using titanium-nitrogen alloys as anode material showed that no significant quantity of nitrogen was transferred to the cathode deposit. The nitrogen of the anode remained in the scale, and the titanium-nitrogen alloy was anodically insoluble in the electrolyte when the nitrogen content was 11 weight-percent.

Jan 1, 1966

By W. C. Maurer

A study of bit-tooth penetration, or crater forniation. under simulated borehole condirions has been made. Pressure conditions existing when drilling with air, water and mud have been sirnulated for depths of 0 to 20.000 ft. These crater tests showed that a threshold bit-tooth force must he exceeded before a crater is .formed. This thresh old force increased with both tooth dullness and diflerenrial pressure between the borehole and formalion fluids. At low differential pressures, the craters formed in a brittle manner and the cuttings were easily removed. At high differenlial pressures, the cunings were firmly held in the craters and the craters were formed by a pseudoplas-tic mechanism. With constant farce of 6,500 16 applied to the bit reeth, an increase in differential pressure (sitnulated mud drilling) from 0 to 5,000 psi reduced the crater volumes by 90 per cent. A comparable increase in hydrostatic fluid pressure (simulated water drilling) produced only a 50 per cent decrease in volutne while changes in overburden pressure (simulated air drilling) had no detectable effect on crater volume. Crater tests in unconsolidated sand subjected to differential pressure showed that high friction was present in the sand at high pressures. Similar friction belween the cuttings in craters produces the transition from brittle to pseudo plastic craters. INTRODUCTION The number of wells drilled below 15,000 ft increased from 5 in 1950 to 308 in 1964. Associated with these deep wells are low drilling rates and high costs. High bottom-hole pressures produce low drilling rates by increasing rock strength and by creating bottom-hole cleaning problems. This paper describes an experimental investigation of crater formation under bottom-hole conditions simulating air, water and mud drilling. Although numerous investigators have studied bit-tooth penetration (cratering) at atmospheric pressure conditions, only limited work has been done on cratering in rocks subjected to pressures existing in oil wells. Payne and Chippendale2 have studied cratering in rocks subjected to hydrostatic pressure using spherical penetrators. Garner et aLJ conducted crater tests in dry limestone by varying overburden pressure and borehole fluid pressure independently and using atmospheric formation-fluid pressure Gnirk and Cheathem4,5 have studied crater formation in several dry rocks subjected to equal overburden and borehole pressure and atmospheric formotion pressure. Podio and Gray studied the effect of pore fluid viscosity on crater formation using atmospheric borehole and formation-fluid pressurc and varying overburden pressure. Although these studies have provided useful information on crater formation under pressure, they were limited in that the three bottom-hole pressures could not be varied independently and, therefore, that many drilling conditions could not be simulated. The prersure chamber used in this study allowed visual observation of the cratering mechanism and independent control of the borehole, formation and confining pressures. By using different fluids in the chamber, pressure conditions existing in air, water and mud drilling to depths of 20,000 ft were simulated. The mechanisms involved in cratering at these different pressure conditions were studied for teeth of varying dullness and at different loadins rates. High-speed movies (8,000 frames/sec) and closed-circuit television were used to visually study the crater mechanism under pressure. EXPERIMENTAT PROCEDURE PRESSURE CHAMBER The Pressure chamber in Fig. I was used to simulate bottom-hole pressure conditions. This chamber has been pressure-tested to 22,500 psi and is normally operated at pressures up to 15,000 psi. The chamber contains four lucite windows' used for illuminating and observing the crater mechanism under pressurc. A closed-circuit television and a Fastax camera (8,000 frames/sec) have been used in these studies. Cylindrical rock specimens (8-in. diameter X 6-in. long) were subjected to three independently controlled pressures simulating overburden, borehole fluid and formation-fluid pressures. Overburden pressure, which corresponds to the stress induced by the overlying earth mass, was applied by exerting fluid pressure against a rubber sleeve surrounding the rock. Borehole pressure, which is the pressure exerted by the column of mud in the wellbore, was simulated by applying pressure to the fluid overlying the rock in the chamber. Formation pressure was simulated by applying pressure to the water saturating the rock. The borehole and formation pressures were equal except when mud was used in the chamber, in which case the differential pressure between these fluids acted across the mud filter cake.

Jan 1, 1966

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By J. W. Town

The Bureau of Mines conducted phosphate beneficiation studies to determine the influence of mineralogical and textural features on the recovery of phosphate from select bed and composite samples representing different phosphate rock types of the western Phosphoria Formation. Batch heavy-liquid tests showed that ore grade) pellet size, and type of interstitial material were significant parameters affecting concentrate grade and recovery. Recoveries at acid grade (31.5 percent P2O5) ranged from 98 to 56 percent. Liberation was essentially complete at 28 mesh, and recoveries tended to drop when overgrinding occurred.

Jan 1, 1966