Search Documents

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

By K. A. Fowler, L. W. Higley

The effect of uranium on the transformation kinetics and the hardenability of a low- alloy steel was evaluated . Isothermal transformation curves were developed from metallographic studies , and hardenability was determined by standard Jominy end- quench tests . For the steels investigated , the addition of 0.15 weight- percent uranium was found to produce a significant shift in the isothermal transformation curve and caused a related increase in hardenability . These effects diminished rapidly when the uranium content was increased above 0.2 weight - percent .

Jan 1, 1964

By George H. Holmes

Beryllium deposits in the northern Virgin Mountains , Clark County , Nev . , and Mohave County , Ariz . , about 70 miles northeast of Las Vegas , were investigated by the Bureau of Mines . The investigation indicated a widespread occurrence of beryllium- bearing pegmatites within an extensive belt of mica - schist . Several deposits with significant beryllium mineral concentrations were encountered . Only a few of the samples analyzed contained more than 1 percent beryllium oxide ( BeO ) ; in many of the samples , no beryllium was reported . The average tenor of samples from the more important occurrences was 0.25 percent BeO . Chrysoberyl is the predominant beryllium mineral in the pegmatite sills ; beryl predominates in the more massive bodies . Minute quantities of cesium and lithium minerals also occur , but no columbium , tantalum , or other rare minerals were found . Ore dressing tests on a composite sample containing 0.28 percent BeO which was representative of the pegmatite sills , indicated an 85 percent recovery of the chrysoberyl ( 70 percent recovery of total BeO ) by gravity concentration in a concentrate containing 17.6 percent BeO .

Jan 1, 1964

By H. R. Shell, John L. Miller, M. V. Denny

In the mica research program conducted by the Bureau of Mines at Norris , Tenn . , many micas other than silicon fluorphlogopite have been synthesized . It has been well established since the initiation of the program that synthetic micas are important materials useful for their superior or unique properties as well as substitutes for natural micas . The possibility of controlling the physical properties of synthetic mica by isomorphic substitution of other ions in the fluorphlogopite lattice further emphasizes the importance of these materials . Accurate measurement and reporting of their properties constitute an essential part of the research program . The study of germanium fluorphlogopite is in keeping with the requirements of a comprehensive study on isomorphic substitution , specifically to identify precisely the material -- chemically , structurally , and optically . The X- ray measurements , including indexed powder and single crystal data , with a description of the methods used to obtain these data , are provided . 5 Earlier work on germanium mica by R. A. Hatch et al . (5) gave an estimate of the cell parameters from X - ray powder data , but no attempt was made to index the diffraction pattern or to determine the space group symmetry . Later work by E. A. Schatz and J. C. Withers (9) listed X- ray and optical measurements , but no attempt was made to index the mica or determine its symmetry . Roth (7) found that germanium dioxide having the a - quartz structure , when heated with equimolar percentages of MgO , CaO , Sr0 , or Ba0 at 1,235 ° C , formed ABO3 -type compounds , e.g. MgGe03 isostructural with enstatite (MgSiO3 ) . Geo₂ also has a rutile - type polymorph with Ge ++ ions in octahedral coordination . Germanium was substituted for silicon in the serpentine structure by Roy and Roy (8 ) using hydrothermal techniques . These authors wrote as follows : "The substitution of Ge + for Si + yielded a magnesia - germania serpentine , formed easily in euhedral hexagonal plates which in some instances were visible in the light microscope . Electron micrographs and the sharp X - ray diffraction patterns confirm a plate - like rather than tubular habit . " It has been shown in this investigation that substitution of germanium for silicon in the mica structure is readily accomplished without radically changing the characteristics of the mica . Substitutions in the mica structure take place in three locations : Tetrahedral , octahedral , and interlayer positions . The tetrahedral positions are normally occupied by Sit or by a combination of Sit with Al +3 the most common combination being 2A1 +3 and 6Si +4 · , The octahedral position , which has six - fold coordination in phlogopite , contains a larger cation such as magnesium . In muscovite it contains only 2A1 ions ; therefore , this mica is considered a dioctahedral mica , whereas phlogopite is considered trioctahedral . +3 The interlayer position has twelve - fold coordination with six oxygen ions from each of two adjacent tetrahedral silica layers . This is the cleavage plane of the mica and commonly contains the largest cation in the mica structure (e.g. potassium) .

Jan 1, 1964

By David W. Wisecarver

This report describes a tool to engage and/or place a Bureau of Mines type gage to measure borehole deformation in a horizontal , 1½ - inch - diameter , stress relief borehole . The tool was successfully used at a borehole depth of 105 feet . Practical usage up to borehole depths of 200 feet might be realized . The tool was designed to work inside EX- size ( 1½ - inch ID ) diamond - drill drive casing used as drill rod and through which the deformation gage is guided into an EX- size stress relief borehole . Through laboratory experiments it was found that by exercising a reasonable amount of care the deformation gage could be placed at a point within a ± .01 foot distance of a predetermined depth in a horizontal EX- size hole and that the deformation measuring piston or plunger of the gage could be oriented in the borehole within 0.5 ° of a preselected angle of orientation in a vertical plane .

Jan 1, 1964

By Sarkis G. Ampian

Published optical microscopic and X- ray diffraction characteristics of the following compounds are critically evaluated and compared with Bureau of Mines data : Tricalcium aluminate , calcium monoa luminate , dodecacalcium heptaluminate , dicalcium silicate , tricalcium silicate , and sodium aluminate . A recommended set of definitive optical and X- ray diffraction characteristics is presented . These values are used to identify products of the lime soda sinter process for production of alumina . Polymorphism of gamma- , beta- , and alpha prime - dicalcium silicate is reexamined , and new data are presented on polymorphism of tricalcium silicate and sodium aluminate by high- temperature X- ray diffractometry . Polymorphism is not observed for tricalcium aluminate , calcium monoaluminate , and dodecacalcium heptaluminate . Bureau of Mines data indicating a stoichiometry of 12Ca0.7A10 for the phase 5Ca0.3A1 0₂ are discussed . A critical review of the literature concerning calcium dia luminate and sodium undecaluminate ( 8 -A10 ) is also included .

Jan 1, 1964

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By M. E. Tyrrell, C. W. Houck

Mixtures of zirconium diboride and refractory metals of group VI were resistance sintered to high - density compacts using modified electric welding equipment . To evaluate the use of chromium , molybdenum , or tungsten as binders for zirconium diboride the sintered compacts were examined in polished sections and tested for crushing strength , hardness , microhardness , oxidation rate , and resistance to mechanical shock . Chromium yielded the highest compressive strength , the greatest resistance to mechanical shock and oxidation , and a satisfactory Rockwell hardness . Molybdenum did not yield a satisfactory cermet . Tungsten yielded compacts having high microhardness but very low mechanical strength .

Jan 1, 1964

By Alla D. Mah

The heat of combustion of aluminum carbide (Al, C3 ) , obtained directly by combustion calorimetry , was AH298.15 -1,029.6 ± 1.9 kcal / mole . == The heat of formation of aluminum carbide corresponding to this value was AH298.15 = -53.4 ± 2.0 kcal /mole .

Jan 1, 1964

By Charles H. Atkinson, Robert T. Johansen

Tremendous volumes of petroleum ( crude oil and natural gas ) at present cannot be recovered economically . The feasibility of using nuclear explosions for production stimulation therefore has been investigated . Data from underground nuclear tests conducted by the Atomic Energy Commission were reviewed , and the physical effects were evaluated for stimulating petroleum production . Calculations of the effect on ultimate recovery of increasing reservoir temperature with nuclear explosives showed disappointingly small increases . Production increases caused by fracturing of massive low- permeability reservoirs appear technically and economically promising . Petroleum reservoirs that might be converted from submarginal to commercial production are being located and evaluated as to potential reserves and as a location for a field test .

Jan 1, 1964

By L. H. Adami, E. G. King

The heats of formation of four sulfides --MnS ( alabandite ) , FeS ( hexagonal pyrrhotite ) , ZnS ( wurtzite ) , and CdS ( greenockite ) -- were determined by hydrochloric acid solution calorimetry . The heats of formation from the metals and rhombic sulfur at 298.15 ° K are , respectively , -51.01 ± 0.19 , -23.81 ± 0.24 , -45.86 ± 0.20 , and -35.70 ± 0.30 kcal /mole . The corresponding free energies of formation were calculated from the heats of formation and the pertinent entropy values .

Jan 1, 1964

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By Scott W. Hazen, Richard F. Link, George S. Koch

The Mi Vida mine , Big Indian district , San Juan County , Utah , is in an ore deposit of uranium and vanadium minerals disseminated in certain sedimentary beds of the Triassic Chinle formation . Statistical analysis of assays of samples taken from the ore body affords an estimate of the grade of the ore body and provides a prediction about the direction of best mineralization beyond the sampled area . The basic data analyzed are assay results for uranium ( Uз Og ) , vanadium (V₂O ) , and lime (CaO ) from 225 channel samples cut at 79 sample points . Through the use of appropriate statistical methods , particularly regression analysis , the grade of ore may be estimated more precisely than by conventional means , and the most favorable direction to extend the mine may be predicted . Frequency distributions of assay residuals for uranium , vanadium , and lime are compared to frequency distributions of assays without regard to trend . Correlations among these variables are obtained and interpreted . The statistical methods employed illustrate certain techniques that may be used to analyze assay data from ore deposits in general .

Jan 1, 1964

By H. D. Hess, C. P. Mabie

This report describes in detail the results of petrographic research conducted on 21 phosphate ores representing important deposits in southwestern Montana , southeastern Idaho , and northeastern Utah . The ores are described and categorized by mineralogical and chemical composition , thermal behavior of organic carbon , and textural constitution . Descriptive and genetic classification schemes applicable to western phosphate ores are discussed ; results from related studies made of the collophane mineralogy are also presented . The latter studies were centered on determining unit - cell dimensions and CO₂ , P2O5 , and fluorine content of collophane concentrates of 11 high - grade phosphate- rock hand specimens selected solely for this purpose . On the basis of this investigation , operational methods have been developed for quantitatively describing textural and compositional features that are likely to be significant in determining the response of phosphate ores to conventional beneficiation treatments ; systems for classifying the ores in relation to these features have been proposed . Studies to date point out distinct textural and compositional variations in the western phosphates and illustrate their importance in determining optimum beneficiation procedure .

Jan 1, 1964

By Charles C. Myers, Robert M. Doerr

The apparatus described was developed for determining the kinetics of gas - solid reactions at high temperatures by measuring the volume of gas consumed with respect to time . This apparatus consists essentially of a horizontal precision- bore glass tube connecting a small reaction chamber in a furnace to a large constant - temperature reservoir . A drop of mercury in the tube separates the two sides of the system and serves as an indicator that moves at a speed proportional to the rate of gas consumption . The sensitivity of the apparatus depends inversely on both the density of the gas in the system and the cross - sectional area of the tube ; with a tube having an area of 0.079 cm² , the sensitivity for oxygen at 308 ° K and 0.5 atm is 20 cm/mg . The reproducibility of data with the volumetric apparatus is good .

Jan 1, 1964

By T. A. Henrie, E. K. Kleespies

Carbon reduction of rutile and ilmenite in nitrogen and ammonia atmospheres was studied as a method of preparing titanium nitride . Ammonia was a better nitriding agent than nitrogen . The contact between the solid reactants , carbon and rutile , was a prime factor in nitrogen atmospheres and was of lesser import in dissociated ammonia . The reduction process for conversion of rutile to the nitride required carbon . The nitriding of ilmenite- carbon mixtures produced titanium nitride and elemental iron .

Jan 1, 1964

By D. W. Bridges, S. R. Borrowman

Thorium and yttrium oxides were recovered from siliceous ores of the Powderhorn , Colo . , area . Processing comprised ( 1 ) acid curing and subsequent ( 2 ) acid baking , ( 3 ) leaching , and ( 4) solvent extraction of thorium , using a primary alkylamine , and yttrium , using di - 2 - ethylhexyl phosphoric acid . About 95 pct of the contained thorium and yttrium was recovered from ore containing 1.2 pct Th02 and 0.5 pct Y₂ 03. The thoria product was 99 pct Tho ; the yttria product was 77 pct Y₂ 03. A 150 - to - 1 concentration ratio was effected on the latter , but some contaminating lanthanon - group oxides remained .

Jan 1, 1964

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

To increase safety and productivity in mining , the potential uses and hazards of rigid foam were investigated by the Bureau of Mines Experimental Coal Mine . This research resulted in the development of chemical formulations , spraying equipment , and application procedures that permit safe and effective use of urethane foams for improving mine ventilation , for reducing weathering of mine rock and steel , for constructing seals in fire areas , and for thermal insulation .

Jan 1, 1964

By Robert J. Brennan, Edward R. Navrocky, John W. Buch

In an effort to establish a highly productive mechanized mining system for anthracite beds pitching between 10 ° and 20 ° , for which conventional mobile equipment is not adaptable , the Bureau carried out an experiment in longwall mining using an Anderton- type drum cutter loader and friction - type yielding steel roof supports . The roof- support system proved to be inadequate for breaking the overhanging roof at the break line supports , with the result that the roof broke over the solid coal . The accompanying subsidence destroyed the continuity of the roof in the work area , and the project was discontinued .

Jan 1, 1964