Search Documents

By Toshimi Yamane

The internal friction of cold-worked titanium iso-thermally annealed at temperature below the recrystallization temperature was measured. The internal friction was calculated from the half width of a resonance curve of the specimen which was vibrated transversally by the electromagnetic method. The experimental results were as follows: 1) The specimens annealed for a long time at temperature below the re crystallization temperature after cold working have the strain-amplitude dependent internal friction. 2) The internal friction increased by the cold working was decreased during the isothermal annealing. The reason of decrease of the internal friction is considered to be caused by the annihi-lation of lattice defects. 3) There is a linear relation between logQt-1/Q0-1 and (1/T)2/3 below the recrys-tallization temperature, where Q0-1 is the internal friction standing 24 hr at the room temperature after cold rolling, Qt-1 is the internal friction annealed at T°K for t min. 4) The hardness of the cold-worked titanium does not change by the annealing at 300°C for a long time but decreases by annealing at 400ºand 460°C. METALS, when cold worked, show sharp changes in physical and mechanical properties' The internal friction of cold-worked metals increases sharply and has a maximum value1,2 connected with working de- grees. The increased internal friction of cold-worked metals is recovered by annealing. This phenomenon is the well known effect called Köster effect. The recovery of the internal friction occurs earlier than the changes in tensile properties, hardness, or X-ray diffraction, and is very sensitive to the structure of a metal. The mechanism of the recovery at a temperature lower than the recrystallization temperature is being considered variously by many investigators: there are such views as the annihilation of dislocations by smith,' the rearrangement of dislocations mentioned by Nowick,4 and interaction of dislocation with point defects.5 Smith and Nowick also considered the interaction but it is so difficult for them to explain the rearrangement mechanism systematically, it being not considered a special model; therefore, we do not explain it quantitatively. Experiments measuring the recovery of the internal friction of cold-worked metals were performed by Gordon and Nowick6 on NaCl, and by Smith on copper. In addition, there are many studies, particularly those of measurements on copper by other investigators. There are comparatively many investigations on aluminum and iron which are the cubic system,'-' but only a few on metals of the hexagonal system.10 In view of this, I investigated cph titanium at room temperature and measured the internal friction after annealing isothermally at temperature lower than the recrystallization temperature. SAMPLES AND EXPERIMENTAL METHOD samples for the experiment were cut from a 6-mm titanium plate. The long direction of samples was

Jan 1, 1963

Research, whether applied or fundamental, is a human endeavour which increases our understanding of nature. It is insufficient to simply observe, explore, record and classify. It i necessary, as well, to fit the observations into a satisfying theoretical scheme; that is, to synthesize. Two examples of successful research programs in physical metallurgy are di cussed from this point of view. A pessimistic view is taken of the prospects for rapid growth of research activities in the Canadian metallurgical industry. THE term "research" is used indiscriminately to describe any intellectual or experimental activity which leads to a change in society. Proponents of various activities, ex-tending all the way from alloy development to subliminal advertising, use the status of the term for special advantage. With the Canadian Government entering upon a project of support to industrial research, it might be well to determine what definition is most in the public interest. As an academic, I have a rather jealous attachment to the definition that research, whether applied or fundamental, is a human endeavour which increases our understanding of nature.

Jan 1, 1963

By Warren C. Gerler

An overland belt conveyor system is installed for only one reason to save money. It must pay its way on a ton-mile basis over a stated period of time, and do so in competition with other forms of transportation. Such a system with its economies has recently been installed at Simco-Peabody's mine near Coshocton, Ohio by Link-Belt Company. Three miles in length, this system carries coal from open pit and underground mining facilities to the Conesville Power Plant of Columbus & Southern Ohio Electric Company. The coal was formerly trucked from the mine direct to the power plant; but over the years the mining operations have moved progressively farther and farther from the plant, making the over-the-road hauling distance correspondingly greater. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. The majority of the coal is recovered by conventional strip mining. Some underground mining` is performed by the high wall method.

Jan 1, 1963

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3'4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,'-' the segregation process became a successful industrial operation.'r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By Paul T. Allsman

THE THREE words, research, mechanization, and automation are keynote words for mining technology during 1962. Basically interrelated, they not only express the major technologic developments in mining but are the signposts pointing out the road ahead. The process represented by each of these words is evolutionary rather than revolutionary, but developments during the past year indicate a climactical stage has been reached in the process of evolution. Mining research has progressed beyond the stage of academic discussion and is a programed activity within the Federal Government,3 the mining colleges,4 and many of the large mining companies.5 Research was a major agenda item at various national and international mining meetings in 1962. A list of these meetings would include such diverse locales as the Workshop and Symposium on Computers and Computer Applications in Mining and Exploration at the University of Arizona in March; and the 5th Rock Mechanics Symposium at the University of Minnesota, in May; the Rock Mechanics Symposium at McGill University, Montreal, Canada, in September; and the Colloquium XIII, International Society for Rock Mechanics, at Salzburg, Austria, in November.

Jan 1, 1963

By Peter Moon

THE mineral industry of Canada relies heavily upon the talent of its technical men. It is vital to the well-being of the industry that its supply of young, trained men be adequate. At the present time, the industry is acquiring only 200 new graduates a year. The shrinking supply is far below present and future requirements. Other industries and research organizations are competing for engineers and scientists. Dr. J. B. Mawdsley (1), Past-President of the Canadian Institute of Mining and Metallurgy, has recently outlined a program designed to attack the problem. Dr. J'. C. Sproule (2), another former President of the Institute, has stated that: "The need for selection of trainee material is commonly recognized, but little is done about it." The following paper contains a short discussion of occupational interests, and outlines research, using psychological knowledge and measuring techniques, aimed at the identification of desirable recruits for the mineral industry.

Jan 1, 1963

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By Paul Gordon

It is shown that equations for grain-boundary migrntion given by Gordon and Vandermeer, based on a theory first advanced quantitatively by Lucke and Detert, satisfactorily explain recent data on both GRAIN boundary migration in recrystallization and in postrecrystallization grain growth has been the subject of extensive studies for many years. Only solute-independent and solute-dependent boundary migration during recrystallization in zone-refined, poly crystalline aluminum, and during grain growth in zone-refined tin. with the advent of zone-refining, however, has it been possible to carry out such studies on high-purity metals, and thus to delineate quantitatively the major effect On the migration rates of very small percentages of dissolved imPurities. Earlier exPerimental work almost invariably gave migration rate parameters which disagreed with theoretical predictions

Jan 1, 1963

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau's permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By T. Gleason

Problems involved in applying wet scrubbers to gas cleaning coal dust from thermal dryers are reviewed. Careful consideration of all the elements going into a modem coal preparation plant is required in view of the increasing difficulty of applying suitable gas cleaning equipment. This problem arises not only from the presence of finer coals to be handled, but also from the pressures applied by both the general population and the plant operators to improve the standard of gas cleaning performance. The Peabody scrubber is presented by the author as a machine designed to help improve this cleaning operation. Wet scrubbing of fine coal from thermal dryers poses a number of problems in adapting the gas cleaning equipment to the fine particulate matter. Among them are: 1) Dust in gases leaving the thermal dryer cyclones is often extremely fine with high percentages of total dust loading less than 1p in size. 2) Flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulfur or higher. Therefore, comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3) Requirements for residual coal loadings leaving the gas scrubber are continually being lowered, while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend. 4) Installation of a scrubbing system on thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore, the operating costs of gas pressure drop and water requirements must be held to a minimum. We have, then, the basic situation which calls for comparatively high cost stainless steel alloy wet scrubbers, which must be highly effective in removing coal fines particularly in the 0 to 5-p size range. Further, the standards of scrubber performance are continually being raised towards the level where gas discharged from the scrubbers must be essentially free of any coloration due to residual dust. In view of the highly refractive nature of fine coal dust, residual loadings of 0.01 grains per cu ft or less are required to provide a color free discharge gas. In the present specifications under consideration a residual coal loading of 0.05 grains per cu ft would be considered color free, since the discharge gases are saturated in the range of 150°F. The steam plume acts as a masking agent at the point of discharge, and upon dissipation of the 150° saturated vapor stream, the effluent gas stream could be essentially color free. The specification under consideration calls for residual solids loading of 0.05 or less grains per cu ft, given a coal size distribution shown in the basic data in Table I. It is noted that the dust laden coal stream has a size distribution by weight of 33% in the 2 to 5-p size range and 55% in the 0 to 2-p size range. The particle size distribution given in the specifications does not detail the percent by weight less than 1-p in size, and more important, the size distri-

Jan 1, 1963

By John B. Jones

New concepts in shaft kiln processing are included in the design of two large diameter shaft kiln plants now under construction. One kiln will be used to produce cement clinker at the Boettcher plant of the Ideal Cement Company at Fort Collins, Colorado. The other kiln is for the semi-commercial oil shale plant for Petrobras, the Brazil National Oil Company at Sao Mateus do Sul, Parana, Brazil. Investigations on application of the new concepts are proceeding in a portable pilot kiln. The shaft kiln has long been recognized as a method of gas-solids contacting having the following principle advantages: l. High thermal efficiency 2. Ability to handle a variety of feed materials with a wide range of particle sizes 3. Minimum investment and operating cost

Jan 1, 1963

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and publishes, periodically health and safety statistics. This report includes data for 1961 on injury experience, with related employment statistics, at coal mines in the United Status. These data are presented in tabular form under the following headings; General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1963

By Neal Cochran

I consider it a distinct privilege to be afforded the opportunity of discussing the program of the Office of Coal Research. The principal activities I will be discussing are concerned with projects that fall in the utilization area. I will, to be sure, touch on other activities of the Office of Coal Research but am not equipped to discuss these activities in great detail. Research activities of the Office of Coal Research are conducted on a contract basis with commercial, academic, and non-profit institutions. We do not operate any laboratories of our own but we do maintain a very small staff for technical and administrative supervision of our contractors. We have consistently attempted to interest outstanding, creative, and practical research organizations in our program. We are constantly seeking the imaginative new idea that will materially reduce the cost of mining coal, transporting it, or will process it into a more convenient and useable form. In assessing proposals and in developing our program, we search for the improvements that will develop large-scale new uses for coal or coal products or those that support these new uses.

Jan 1, 1963

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By J. B. Stubbins, D. F. Coates, K. L. McRorie

Twenty-two pit slides that occurred in two Canadian open pit mining properties are analyzed. Information on the results of laboratory tests of the rocks and a brief description of the geological environment are also presented. One deduction from the study is that slides seem to be predictable by using established theory. This corroboration indicates that, contrary to normal mining practice, the appropriate slope angle should vary with the height of the wall. In addition, if the general ground water level around an open pit can be reduced, the appropriate slope angles of the walls could then be increased by a determinable amount. The ultimate objective of these investigations is to determine the relationship between the percentage probability of failure of any slope designed with specific strength paraheters. With this relationship it would then be possible to determine optimum slope angles. Because of changes in various economic factors, open pits are now being mined to much greater depths than previously. The need to keep stripping ratios low without endanrrerine.-- lives and equipment provides a strong incentive to determine the maximum practicable wall slopes. Applied research work is currently being conducted to establish the methods for analyzing optimum slopes.

Jan 1, 1963

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By O. Skiredj, J. F. Elliott

It has been necessary to collate the available data on the solubility of graphite in Fe-Si-Mn alloys for a study of slag-metal equilibria in ferromanganese production. That study will be reported later; the collation is reported here. The carbon content of graphite-saturated liquid iron above 1153ºC by Chipman and co-workers1 is: %C= 1.34 + 2.54 x 10~3t(°C) [l] For graphite-saturated manganese above 1322ºC it is: %C = 2.68 + 3.52 x 1CT3 t(°C) [2]

Jan 1, 1963

By C. Dean Starr

The physical basis of the equation correlating electrical conductizlity and temperature coefficient of resistance of solid solution alloys has been inzlestzgated and the nature of the constants evaluated. It is shaun that the same form of correlation is valid irrespective of the magnitude of the temperature coefficient. However, the effect of therma1 expansion and change in resistivity with temberature nust be considered when the magnitude of the temperature coefficient of resistance is near zero. In a comprehensive literature survey conducted at the Armour Research Foundation in 1950, it was found that a linear relationship exists between the electrical conductivity, K, and the temperature coefficient of resistance, a, for solid solution alloys. This was expressed by the equation where B, a constant, depends on the solvent metal but not the solute. A continuing investigation by Hansen, Johnston, and Parks showed this equation was generally appropriate for Cu, Ag, Au, Pd, Pt, and Co base binary solid solution alloys as well as for many ternary alloys of copper over a range of conductivities and temperature coefficient of resistances from 0.02 to 0.60 reciprocal pohm cm and-0.00015to0.004Q per 0 per "C respectively. Eq. [I] was not always valid for alloys that exhibited a change in state (magnetic to nonmagnetic) or for alloys that had a temperature coefficient of resistance near or below zero. For example, in nickel alloys, a simple linear curve as predicted by Eq. [l] was not obtained when the conductivity was plotted against the temperature coefficient of resistance. Hansen suggested that deviations observed were caused by transitions from a ferromagnetic to a nonmagnetic state. Subsequent and more extensive data by ronin on Ni-Mn alloys confirmed Hansen's postulate. While both states independently showed a linear relationship between K and a, the value of B was different for the two states. In some copper and gold base alloys, as well as the platinum and palladium alloys investigated by Hansen, the conductivity did not extrapolate to zero at zero a as demanded by Eq. [I]. This deviation can be readily corrected by simply adding a constant to Eq. [I.] whence Eq. [2] shows the K decreases as a decreases but that K has a positive value when a = 0 which is observed for commercial solid solution alloys as well as the experimental alloys tested by Hansen. While other methods of correlation of electrical properties have been made such as the one by Starr and Wang3 who found a linear relationship between resistivity and temperature coefficient of resistance for Ni-Cr-Al-Cu alloys, the data, in general, can also be correlated by a form of Eq. [2]. Thus, Hansen's empirical equation has considerable merit. The objective of this paper is to determine the physical basis for this equation and to examine the region near zero a in more detail. ELECTRICAL CONDUCTIVITY VS TEMPERATURE COEFFICIENT OF FU3SISTANCE The resistance of a metal or alloy is defined as

Jan 1, 1963

By John E. Kinnison

The Mission mine, located in southern Arizona near Tucson, is a recently developed open pit which produces 15,000 tons per day of copper ore. The mine lies on a wide and gently sloping bajada sweeping northeasterly from the Sierrita mountains. It derives its name from the nearby Mission San Xavier del Bac, built circa 1700. The ore body is everywhere covered by about 200 feet of alluvium, as are the adjacent Pima and Palo Verde mines. The geology of the Mission deposit is known principally through the study of diamond drill holes spaced 150 to 300 feet apart. The open pit is in an infant stage and has not yet revealed much of the deposit, although information obtained there by the operating staff, and from a few thousand feet of exploratory underground workings, has added significantly to the general fund of knowledge. Permission to publish was granted by the American Smelting and Refining Company. I am indebted to Kenyon Richard and J. H. Courtright for criticism of this paper and for their direction during the several years in which I studied the Mission deposit. Acknowledgment is given to consultant in petrography, Robert L. DuBois of the University of Arizona. The only previous publication pertaining directly to the geology of file Mission deposit appeared in 1959 (Richard and Courtright), and may not be everywhere readily available. Cooper (1960) has published a short paper on the district

Jan 1, 1963